Scribd
Upload
253 views

Creating LUN in NetApp Using CLI

Creating a LUN in NetApp involves using CLI commands to carve out storage space on a vfiler and present it to a Solaris machine using iSCSI. The key steps are to 1) configure the iSCSI HBA on Solaris, 2) login to the NetApp console, 3) determine the volume with enough space, 4) create a qtree, 5) use CLI commands to create the LUN, 6) create an initiator group with the Solaris IQN, 7) map the LUN to the initiator group, and 8) verify the LUN is visible on the Solaris box.

Uploaded by

anon_326668689
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
253 views

Creating LUN in NetApp Using CLI

Creating a LUN in NetApp involves using CLI commands to carve out storage space on a vfiler and present it to a Solaris machine using iSCSI. The key steps are to 1) configure the iSCSI HBA on Solaris, 2) login to the NetApp console, 3) determine the volume with enough space, 4) create a qtree, 5) use CLI commands to create the LUN, 6) create an initiator group with the Solaris IQN, 7) map the LUN to the initiator group, and 8) verify the LUN is visible on the Solaris box.

Uploaded by

anon_326668689
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

Creating LUN in NetApp Using CLI

If you want to create a LUN (Logical Unit Number) on a vfiler in NetApp, you will be forced to use CLI
commands. There is no wizard GUI tool for vfilers at least for now.
To carve up a storage space in NetApp to be presented to a SPARC Solaris machine using iSCSI
HBA, I used the following steps:
1. Configure iSCSI HBA on Solaris (i.e., configure IP address, netmask, gateway, vlan tagging [it if its
on a separate vlan], etc)
2. Login through NetApp console or remote session.
3. Go to the vfiler
nas3240> vfiler context vfiler-iscsi
4. Determine which volume to create the LUN. Make sure it has enough space.
nas3240@vfiler-iscsi> vol status
nas3240@vfiler-iscsi> df -h
5. Create qtree. I usually create the LUN on qtree level instead of volume. This makes my structure
cleaner.
nas3240@vfiler-iscsi> qtree create /vol/iscsi_apps/solaris
6. Create the LUN using this syntax: lun create -s size -t ostype lun_path
nas3240@vfiler-iscsi> lun create -s 200g -t solaris /vol/iscsi_apps/solaris/lun0
Successful execution of this command wil create LUN /vol/iscsi_apps/solaris/lun0 with a size of
200GB, and space-reserved. For LUN, the best practice is to thick provision (space-reserved), so
you wont have problems when the storage runs out of space.
7. Create initiator group or igroup which contain the IQN for the solaris host. Initiate a iscsi login
command from solaris host, and NetApp will see the IQN number. This IQN number will appear on
the console and you can cut and paste that number. Use this syntax to create igroup: igroup create -i
-t ostype initiator_group iqn_from_host
nas3240@vfiler-iscsi> igroup create -i -t solaris solaris_group iqn.200004.com.qlogic.gs2342345.2

8. Map the LUN to the host using igroup you created. Use this syntax: lun
maplun_path initiator_group [lun_id] where: lun_path is the path name of the LUN you
created,initiator_group is the name of the igroup you created, and lun_id is the identification number
that the initiator uses when the LUN is mapped to it. If you do not enter a number, Data ONTAP
generates the next available LUN ID number.
nas3240@vfiler-iscsi> lun map /vol/iscsi_apps/solaris/lun0 solaris_group
9. Verify LUN list and their mapping.
nas3240@vfiler-iscsi> lun show -m
LUN path
Mapped to
LUN ID Protocol

vol/iscsi_apps/solaris/lun0
solaris_group
2
iSCSI
10. Go to solaris box, and do iSCSI refresh. Check that it can see the LUN disk that has been
provisioned.

What is the difference between NFS and CIFS?


NFS is the "Network File System" for Unix and Linux operating systems. It allows files to be
shared transparently between servers desktops laptops etc. It is a client/server application that
allows a user to view store and update files on a remote computer as though they were on their
own computer. Using NFS the user or a system administrator can mount all or a portion of a file
system.
CIFS is the "Common Internet File System" used by Windows operating systems for file sharing.
CIFS uses the client/server programming model. A client program makes a request of a server
program (usually in another computer) for access to a file or to pass a message to a program that
runs in the server computer. The server takes the requested action and returns a response. CIFS is
a public or open variation of the Server Message Block Protocol (SMB) developed and used by
Microsoft and it uses the TCP/IP protocol.
NFS and CIFS are the primary file systems used in NAS. CIFS tends to be a bit more "chatty" in
its communications.

You might also like