Scribd
Upload
960 views

Flashscan Heat Detectors

honeywell heat detector

Uploaded by

we202
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
960 views

Flashscan Heat Detectors

honeywell heat detector

Uploaded by

we202
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

TC808B1041(CDN),

TC808B1058(CDN),
TC808B1066(CDN)
Intelligent Thermal (Heat)
Detectors with FlashScan
Honeywell TC808B(CDN) Series intelligent plug-in thermal
detectors with integral communication has features that surpass conventional detectors. Point ID capability allows each
detectors address to be set with rotary, decimal address
switches, providing exact detector locations. TC808B(CDN)
Series thermal detectors use an innovative thermistor sensing
circuit
to
produce
135F/57C
fixed-temperature
(TC808B1041/CDN) and rate-of-rise thermal detection
(TC808B1058/CDN)
in
a
low-profile
package.
TC808B1066(CDN) provides fixed high-temperature detection
at 190F/88C. These thermal detectors provide effective,
intelligent property protection in a variety of applications.
TC808(CDN) Series detectors are compatible with Honeywell
XLS series Fire Alarm Control Panels (FACPs) in CLIP or
FlashScan mode
FlashScan (U.S. Patent 5,539,389) is a communication protocol that greatly enhances the speed of communication
between analog intelligent devices. Intelligent devices communicate in a grouped fashion. If one of the devices within the
group has new information, the panels CPU stops the group
poll and concentrates on single points. The net effect is
response speed greater than five times that of earlier designs.

Features
Sleek, low-profile, stylish design.
State-of-the-art thermistor technology for fast response.
Rate-of-rise model (TC808B1058/CDN), 15F (8.3C) per
minute.
Factory preset fixed temperature at 135F (57C); high-temperature model fixed at 190F (88C).
Addressable by device.
Compatible with FlashScan and CLIP protocol systems.
Rotary, decimal addressing (1-99 on CLIP systems, 1-159
on FlashScan systems).
Two-wire SLC connection.
Visible LEDs blink every time the unit is addressed.
360-field viewing angle of the visual alarm indicators (two
bi-color LEDs). LEDs blink green in Normal condition and
turn on steady red in Alarm.
Integral communications and built-in device-type identification.
Remote test feature from the panel.
Built-in functional test switch activated by external magnet.
Walk test with address display (an address of 121 will blink
the detector LED 12-(pause)-1).
Low standby current.
Backward-compatible.
Built-in tamper-resistant feature.
Designed for direct-surface or electrical-box mounting.
Sealed against back pressure.
Plugs into separate base for ease of installation and maintenance. Separate base allows interchange of photoelectric, ionization and thermal sensors.

B210-2251.jpg

General

TC808B1041 in B210LP(A) Base

SEMS screws for wiring of the separate base.


Constructed of off-white fire-resistant plastic, designed to
commercial standards, and offers an attractive appearance.
94-5V plastic flammability rating.
Remote LED output connection to optional RA100Z(A)
remote LED annunciator.
Optional sounder, relay, and isolator bases.
Optional flanced surface mounting kit.

Specifications
Size: 2.1" (5.3 cm) high; base determines diameter.
B210LP(A): 6.1" (15.5 cm) diameter.
B501(A): 4.1" (10.4 cm) diameter.
B200S(A): 6.875" (17.46 cm) diameter.
B200SR(A): 6.875" (17.46 cm) diameter.
B224RB(A): 6.2" (15.748 cm) diameter.
B224BI(A): 6.2" (15.748 cm) diameter.
Shipping weight: 4.8 oz. (137 g).
Operating
temperature
range:
TC808B1041(CDN),
TC808B1058(CDN), TC808B1066(CDN), TC808B1058(CDN):
20C to 38C (4F to 100F); TC808B1066(CDN): 20C to
66C (4F to 150F).
Detector spacing: UL approved for 50 ft. (15.24 m) center to
center. FM approved for 25 x 25 ft. (7.62 x 7.62 m) spacing.
Relative humidity: 10% 93% noncondensing.
Thermal ratings: fixed-temperature setpoint 135F (57C),
rate-of-rise detection 15F (8.3C) per minute, high temperature heat 190F (88C).

ELECTRICAL SPECIFICATIONS
Voltage range: 15 - 32 volts DC peak.
Standby current (max. avg.): 300 A @ 24 VDC (one communication every 5 seconds with LED enabled).
LED current (max.): 6.5 mA @ 24 VDC (ON).

Applications
Use thermal detectors for protection of property. For further
information, go to systemsensor.com for manual I56-407-00,
Applications Manual for System Smoke Detectors, which provides detailed information on detector spacing, placement,
zoning, wiring, and special applications.

Installation

INTELLIGENT BASES

The TC808B Series plug-in intelligent thermal detectors use a


separate base to simplify installation, service, and maintenance. Installation instructions are shipped with each detector.
A special tool allows maintenance personnel to plug in and
remove detectors without using a ladder

NOTE: A or CDN suffix indicates ULC Listed model.

Mount base (all base types) on an electrical backbox which is


at least 1.5" (3.81 cm) deep. For a chart of compatible junction
boxes, see 85-3043.
NOTE: 1) Because of the inherent supervision provided by the
SLC loop, end-of-line resistors are not required. Wiring T-taps or
branches are permitted for Style 4 (Class B) wiring. 2) When
using relay or sounder bases, consult the TC811A1006(CDN)
installation sheet I56-1385 for device limitations between isolator
modules and isolator bases.

Agency Listings and Approvals


These listings and approvals apply to the modules specified in
this document. In some cases, certain modules or applications
may not be listed by certain approval agencies, or listing may
be in process. Consult factory for latest listing status.

UL Listed: S1196.
ULC Listed: S6972.
FM Approved.
CSFM:
7272-1130:0206
TC808B1066(CDN) only].

[TC808B1041(CDN)

and

Product Line Information


NOTE: A or CDN suffix indicates ULC Listed model.

TC808B1041: Intelligent thermal detector fixed 135F. Must be


mounted to one of the bases listed below.
TC808B1041CDN: Same as TC808B1041 but with ULC Listing.
TC808B1058: Intelligent thermal detector with rate-of-rise feature.
TC808B1058CDN: Same as TC808B1058 but with ULC Listing.
TC808B1066: Intelligent high-temperature 194F thermal
detector.
TC808B1066CDN: Same as TC808B1066 but with ULC Listing.

NOTE: For details about intelligent bases and their mounting, see
85-3043.

B210LP(A): Standard U.S. flanged low-profile mounting base.


B210LPBP: Bulk pack of B210LP; package contains 10.
B501(A): Standard European flangeless mounting base.

B501BP: Bulk pack of B501; package contains 10.


B200S(A): Addressable Intelligent, programmable sounder
base capable of producing sound output in high or low volume
with ANSI Temporal 3, ANSI Temporal 4, continuous tone,
marching tone, and custom tone.
B200SR(A): Intelligent sounder base capable of producing
sound output with ANSI Temporal 3 or continuous tone.
Replaces B501BH series bases in retrofit applications.
B224RB(A): Intelligent relay base. Screw terminals: up to 14
AWG (2.0 mm). Relay type: Form-C. Rating: 2.0 A @ 30 VDC
resistive; 0.3 A @ 110 VDC inductive; 1.0 A @ 30 VDC inductive.
B224BI(A): Intelligent isolator base. Isolates SLC from loop
shorts. Maximum: 25 devices between isolator bases; see
Note 2 under Installation. Replaces 14507371-005(CDN).

ACCESSORIES
F110: Retrofit flange to convert B210LP(A) to match the
14507371-001(CDN) profile, or to convert older high-profile
bases to low-profile.
F110BP: Bulk pack of F110; package contains 15.
F210: Replacement flange for B210LP(A) base.
RA100Z(A): Remote LED annunciator. 3 32 VDC. Fits U.S.
single-gang electrical box. Supported by B210LP(A) and
B501(A) bases only.
SMB600: Surface mounting kit, flanged.
M02-04-00: Test magnet.
M02-09-00: Test magnet with telescoping handle.
XR2B: Detector removal tool. Allows installation and/or
removal of FlashScan Series detector heads from base in
high ceiling installations. Includes T55-127-010.
T55-127-010: Detector removal tool without pole.
XP-4: Extension pole for XR2B. Comes in three 5-foot (1.524
m) sections.

This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific
applications or anticipate all requirements. All specifications are subject to change without notice.
FlashScan is a registered trademark of Honeywell International Inc.
2011 by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited.

Automation and Control Solutions


Honeywell International Inc.

Honeywell Limited-Honeywell Limite

1985 Douglas Drive North

35 Dynamic Drive

Golden Valley, MN 55422

Scarborough, Ontario M1V 4Z9

www.honeywell.com

74-3354-3 Rev. 12-11


December 2011
Made in the U.S.A.
U.S. Registered Trademark
2011 Honeywell International Inc.
Page 2 of 2

You might also like