Scribd
Upload
308 views

Earthquake Analysis Procedure

Seismic coefficient method is used to analyze buildings up to certain heights depending on their zone and regularity. This document outlines the steps to define and apply seismic loads in STAAD Pro. First, seismic load definitions are generated by specifying parameters from Indian codes like zone factor, response reduction factor, soil type, etc. Then seismic weight is calculated including dead and appropriate live loads. Finally, four seismic load cases are added - two each for X and Z directions with factors of 1 and -1. Appropriate load combinations are used for superstructure and substructure analysis.

Uploaded by

V.m. Rajan
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
308 views

Earthquake Analysis Procedure

Seismic coefficient method is used to analyze buildings up to certain heights depending on their zone and regularity. This document outlines the steps to define and apply seismic loads in STAAD Pro. First, seismic load definitions are generated by specifying parameters from Indian codes like zone factor, response reduction factor, soil type, etc. Then seismic weight is calculated including dead and appropriate live loads. Finally, four seismic load cases are added - two each for X and Z directions with factors of 1 and -1. Appropriate load combinations are used for superstructure and substructure analysis.

Uploaded by

V.m. Rajan
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 4

Earthquake Analysis Using Seismic Coefficient Method

EARTH QUAKE ANALYSIS USING SEISMIC COEFFICIENT METHOD:


Seismic Coefficient method is applicable for buildings:
(a) Regular Buildings :
Height < 90m in zones II & III.
<40m in zones IV & V
(b) Irregular Buildings :
Height < 40m in zones II & III.
<12m in zones IV & V
The Various methods used in STAAD Pro for earthquake analysis are:
1. Lumped mass method (introduced by Research Engineers before
2007)
2. Member weight method (Introduced by Bentley after 2007)
3. Reference load method (Introduced by Bentley after 2007)
4. Converting static load to equivalent seismic analysis .
Design of seismic shear (VB)
Total design seismic base shear VB along any principal direction is given by
VB= Ah W
Ah= Design horizontal acceleration spectrum value
Ah= (Z/2) (I/R) (Sa/g)
W= Seismic weight of building
= Dead load + appropriate amount of imposed load.
Note:
1. Live load upto and including 3.0 KN/m2 =25% of imposed load.
2. Live load > 3.0KN/m2 = 50% of imposed load.
3. For calculating design seismic forces imposed load on roof need not be
considered.
Applying Seismic in STAAD Pro :
There are two parts.
Part 1: Define Seismic load.
Part 2: Applying Defined Seismic Load
Part 1 : Define Seismic Load
The value of Ah is computed by generating Seismic Load Definition by
specifying
following parameters in STAAD.
Main menu CommandsLoadingDefinitionsSeismic LoadIS18932002
(OR)
Click Load and DefinitionsClick DefinitionsSeismic LoadAdd.

Seismic parameter screen will appear. Select Type: IS1893-2002Click


GenerateAdd.
Select city or zone: (Table 2 of IS 1893-2002)
Seismic zone
Seismic
intensity
Zone factor

II

III

IV

Low

Moderate

Severe

Very Severe

0.10

0.16

0.24

0.36

Response Reduction Factor (RF) : (Table 7 of IS 1893-2002)


5 for Special Moment Resistance Frame (SMRF)
3 for Ordinary Moment Resistance Frame (OMRF)
Important Factor (I) : (Table 6 of IS 1893-2002)
1 for ordinary Residential building
1.5

for Important Building

Rock or Soil sites Factor (SS): Clause 6.4.5 of IS 1893-2002)


1 for hard soil (N> 30)
2 for Medium soil (10< N < 30)
3 for soft soil (N< 10)
Type of structure (ST) (optional): (Clause 7.6 of IS 1893-2002)
1 for RCC Frame Building
2 for Steel Frame Building
3 for all other Building
Damping ratio (DM): (Table 3 of IS 1893-2002)
0.05% for concrete.
PX= Period in X direction : (Optional)
PZ= Period in Z direction : (Optional)
The approximate fundamental natural period of vibration in seconds for
RC Frame buildings without brick in- fills T=0.075 h0.75
For all other buildings including frame buildings with brick in-fills Tx= 0.09 h
dx
dx = dimension in X direction.
Tz= 0.09 h
dz

dz = dimension in X direction.
h = height of building in metre
d= base dimension at plinth in metre along the direction of force.
Depth of Foundation (DT): (For under ground structures)
Click Generate Add Close.
To calculate Seismic weight of building (w):
Click Z 0.16 RF 3 I 1.5 SS 2 ST 1 DM 0.05 Add.
Seismic Definitions screen will appear.
Click self weight self weight 1 Add.
Click member weight Loading type: UNI

weight: 12 KN/m (for external

wall)
6 KN/m (for internal wall) Add.
Click Floor weight Pressure : 4 KN/m2 ( dead load)
Y range: Mini: 3.0m Max: 15.0m Add.
Floor weight Pressure : 0.50KN/m2 ( appropriate Live load) Add.
Y range: Mini=3.0m Max=12.0m (except roof slab) Add Close.
Note:
1. W= Seismic weight of Building= Dead load+ appropriate amount of
imposed load. Live load up to and including 3.0KN/m2 =0.25% of
imposed load.
Live load > 3.0KN/m2
=50% of imposed load.
For calculating design seismic forces imposed load in roof need not be
considered.
Click self weight select to view Assign.
Click Member weight Main menu Select Beam parallel to X and
Beam parallel to Z Assign to selected beam AssignYes Close.
2. In seismic analyses always first load case shall be seismic load only.
Part 2: Applying defined Seismic Load :
Click Load case details Add.
Member 1 Loading type: Seismic
Title: Seismic in X +ve Add.

Number 2 loading Type: Seismic


Title : Seismic in X ve Add.
Number 3 loading Type: Seismic
Title : Seismic in Z +ve Add.
Number 4 loading Type: Seismic
Title : Seismic in Z ve Add close.
Highlight seismic in X +ve Add.
Seismic load X direction Factor=1 Add.
Highlight seismic in X -ve Add.
Seismic load X direction Factor=-1 Add.
Highlight seismic in Z +ve Add.
Seismic load Z direction Factor=1 Add.
Highlight seismic in Z +ve Add.
Seismic load Z direction Factor=-1 Add Close.
Load combination to be considered in case of Seismic
1. For Superstructure (Ultimate load condition)
1. 1.5 (DL+LL)
2. 1.5 (DL+ S in X +ve)
3. 1.5(DL+ S in X ve)
4. 1.5 (DL+ S in Z +ve)
5. 1.5 (DL+ S in Z ve)
6. 1.2(DL+LL+ S in X+ve)
7. 1.2(DL+LL+ S in X-ve)
8. 1.2(DL+LL+ S in Z+ve)
9. 1.2(DL+LL+ S in Z-ve)
10. 0.9DL+ 1.5 S in X +ve
11. 0.9DL +1.5 S in X-ve
12. 0.9DL+ 1.5 S in Z+ve
13. 0.9DL + 1.5 S in Z-ve.
2. For Sub structure ( Service load condition )
1. (DL+LL)
2. DL+ S in X+ve
3. DL + S in X-ve
4. DL + S in Z +ve
5. DL + S in Z ve
6. DL+0.8LL+ S in X +ve
7. DL+0.8LL+ S in X ve
8. DL+0.8LL+ S in Z+ve
9. DL+0.8LL+ S in Z-ve

You might also like