Scribd
Upload
147 views

UPC1

The document is a user manual for a Universal Protocol Converter (UPC) that interfaces banknote validators with host machines. It describes how to program the UPC using SAM-BA software or USB to enable compatibility with different validators and machine interfaces. Key sections explain the kit components, power requirements, software installation, connecting the UPC for programming, programming supported protocols, and using the UPC with a validator and host machine.

Uploaded by

Bogicevic Dejan
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
147 views

UPC1

The document is a user manual for a Universal Protocol Converter (UPC) that interfaces banknote validators with host machines. It describes how to program the UPC using SAM-BA software or USB to enable compatibility with different validators and machine interfaces. Key sections explain the kit components, power requirements, software installation, connecting the UPC for programming, programming supported protocols, and using the UPC with a validator and host machine.

Uploaded by

Bogicevic Dejan
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 24

UNIVERSAL PROTOCOL CONVERTER

USER MANUAL

INTELLIGENCE IN VALIDATION

UNIVERSAL PROCOL CONVERTER


1

UPC1

1 INTRODUCTION
This manual describes the operation of the UPC Validator
Interfacing System, programmed with firmware via the Atmel SAMBA programming software or via USB.
This document is intended for those who will:
Program the UPC
Implement the UPC into machines
We recommend that you study this manual as there are many new
features permitting new uses and more secure applications. If you
do not understand any part of this manual please refer to
www.gaming-upc.com.
2 KIT COMPONENTS
The UPC Kit comprises of the following:
UPC Device
UPC to Validator cable
3 POWER REQUIREMENTS
When programming the UPC using the SAM-BA software, it is
necessary to provide power from an external source.

UNIVERSAL PROTOCOL CONVERTOR


2

UPC1

4 GENERAL DESCRIPTION
The UPC is a validator interfacing system designed to enable the
implementation of Bank Note Validators in the field into specific
machines (see Appendix 2 for supported Banknote validators).
It is possible to programme the UPC with an alternative software file
to ensure machine compatibility. The UPC is a communications
buffer and leaves the factory as a straight through voltage
converter.
Once the UPC has been programmed, the user can:
Implement the validator with a standard SSP interface into
a specific machine.
The UPC can be programmed with compatible interface
software via the Atmel SAM-BA programming software.
Reprogramming is also possible via USB.
The UPC software will ensure compatible operation of the
validator in the host/gaming machine.
The UPC is configurable to work with machines which
deliver power at voltages of +12v or up to +48V. The
voltage selection on the UPC must be made by setting
the jumper link on the UPC.
The UPC can operate in various serial mode options TTL,
RS232 or Opto isolated communications.
There are three additional parallel input lines and three
parallel output lines for the UPC at TTL levels.
The validator will be powered from +12v via the UPC.

UNIVERSAL PROTOCOL CONVERTOR


3

UPC1

5 SOFTWARE INSTALLATION ALSO REFER TO SECTION 7


PROGRAMMING
NOTE: - Install the SAM-BA software on to your PC.
The software is available for download using the following web site
link http://www.atmel.com/dyn/resources/prod_documents/Install
AT91-ISP v1.12.exe
It is necessary to ensure that the COM port selected on your PC to
allow programming of the UPC must be within the following range:
COM1 to COM10
It is necessary to use serial communication via debug serial
interface, TXD on pa10 (pin 29), and RXD on pa9 (pin 30) Pins 29 &
30 of the microcontroller are only used as spare comm inputs on
the UPC so we can use them for downloading firmware

UNIVERSAL PROTOCOL CONVERTOR


4

UPC1

UNIVERSAL PROTOCOL CONVERTOR


5

UPC1

UNIVERSAL PROTOCOL CONVERTOR


6

UPC1

UNIVERSAL PROTOCOL CONVERTOR


7

UPC1

6 CONNECTING THE UPC TO A PC


The UPC is connected to a PC for programming purposes via a DA2
kit. The power for the UPC is then supplied via the DA2 kit. When
programming using SAMBA (or JTAG) binary interface files should
be used.
The programming cable connects to pins 11 & 15 of the UPC on
the validator connector (CON2). The firmware is downloaded to
the UPC via a DA2 kit.
The programming cable is configured specifically for the UPC. It is
necessary to ensure that the following pins have been crossed on
the programming cable: Pins 11 & 12 and 15 & 16 must be crossed
over. See APPENDIX B for a drawing of the cable.

UNIVERSAL PROTOCOL CONVERTOR


8

UPC1

7 PROGRAMMING THE UPC


The UPC supports the following interfaces. Please contact
[email protected] for full details of compatible interfaces.

PR01
PR02
PR03
PR04
PR05

PR00
UPC used only as power supply (+48v to +12v) and i/o
voltage levels converter

Compatible Protocols still to be implemented on UPC

PR06
PR07

Please refer to www.gaming-upc.com for further information.

UNIVERSAL PROTOCOL CONVERTOR


9

UPC1

SAMBA or JTAG programming is necessary if firmware becomes


corrupted (this could happen during programming).
DO NOT DISCONNECT the UPC while the firmware upgrade is taking
place. Doing so could permanently damage the UPC. It is
necessary to insert a short circuit in place of R48 (see location
highlighted on the picture below) for more than 10 seconds, but
less than 15 seconds, to allow a new file to be programmed into
the UPC.
The UPC can be programmed via a DA2 kit with the Sam-Ba
software from Atmel as described in this manual. The device that
should be selected for programming is AT91SAM7S64-EK.

1) Install Atmel ISP Programmer (you can download it from


here)
2) Connect UPC CON2 to DA2 via special programming
cable
3) Short R48 (donotfit resistor next to LEDs) on UPC for more
than 10 seconds but less than 15 seconds
4) Unplug UPC and plug back again
UNIVERSAL PROTOCOL CONVERTOR
10

UPC1

5) Start Atmel SAM-BA


6) Select correct DA2 COM port (must be within COM1 and
COM10)
7) Select board AT91SAM7S64-EK
8) Click on connect
9) Click on the open icon next to Send file button and
select firmware file
10)Click on the Send file button
11)Confirm unlocking and locking programmed sectors
12)Click on Link, Disconnect. Unplug the UPC
7.1 PROGRAMMING VIA USB - RECOMMENDED
Install the UPC Utilities software UPCUtilities_1_0_3.msi available to
download from www.gaming-upc.com within Download Centre /
Firmware

UNIVERSAL PROTOCOL CONVERTOR


11

UPC1

The UPC Utilities will now install


UNIVERSAL PROTOCOL CONVERTOR
12

UPC1

Connect the UPC to a pc via a USB cable. Found new hardware


message will appear.

Select No, not this time to Windows Update.


UNIVERSAL PROTOCOL CONVERTOR
13

UPC1

Select Install From A List Or Specific Location (Advanced)

Ensure the location is C\:Program Files\UPCUtilities


UNIVERSAL PROTOCOL CONVERTOR
14

UPC1

Click Continue Anyway to install

UNIVERSAL PROTOCOL CONVERTOR


15

UPC1

Click Finish The UPC software is now installed


To open the UPC Utilities Program select: Start All Programs UPC
Utilities Universal Protocol Converter Utilities.
Using the Utilities Menu tab you can access
Set UPC Options
Monitor
Set PR01 Configuration
Update UPC OS
Connect the UPC to your PC via a USB
cable for programming.

Set UPC Options


Provides information on the currently installed UPC interface and
firmware version.
Host Drive TTL RS232 or Host Drive Opto Isolated options.

UNIVERSAL PROTOCOL CONVERTOR


16

UPC1

Monitor
Select RUN to monitor all traffic:
Target Traffic indicates communication between UPC and
validator
Host Traffic indicates communication between UPC and host
machine
Log file locations allows traffic communication to be saved to a
file on your PC

UNIVERSAL PROTOCOL CONVERTOR


17

UPC1

Set UPC PR01 Configuration Data


Get UPC Data allow manual changes
Set Data to UPC to set changes to UPC
Auto Detect Cfg attach to existing validator and host machine
for current interface information.
Abort Auto Cfg
Exit

UNIVERSAL PROTOCOL CONVERTOR


18

UPC1

Update UPC OS
Use Open UPC Files to alter interfaces.
If the update files do not appear automatically select C: Program
Files/UPC Utilities/Update Files
Select the required interface. Use dpc. files when programming via
USB.
Click Run Update.
Please note this update will take approximately 2-3 minutes
DO NOT DISCONNECT.

The flashing red LED on the UPC indicates it is updating. DO NOT


DISCONNECT the USB or UPC during update.

UNIVERSAL PROTOCOL CONVERTOR


19

UPC1

8. USING THE UPC


8.1 CONNECTING A VALIDATOR TO THE UPC
Connect the UPC to the banknote validator via the supplied cable
(CN382)

UNIVERSAL PROTOCOL CONVERTOR


20

UPC1

8.2 CONNECTING THE UPC TO THE HOST MACHINE


The connections to the UPC are dependant on which interface is
to be used. The cable must be wired as required. The connections
are shown in the table below
Pin Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16

Function
+V
0V
RS232 TxD
RS232 RxD
TxD Opto Emitter
RxD Opto Anode
TxD Opto Collector
RxD Opto Cathode
Parallel In 2
Parallel In 3
TTL RxD
Parallel In 1
Parallel Out 2
Parallel Out 3
TTL TxD
Parallel Out 1

The pictures below show an example cable of an RS232


connection

UNIVERSAL PROTOCOL CONVERTOR


21

UPC1

APPENDIX A COMMS INDICATOR


Led colour
Red
Green

Indication
Valid data from the Host
machine
Valid data from the validator

UNIVERSAL PROTOCOL CONVERTOR


22

UNIVERSAL PROTOCOL CONVERTER


USER MANUAL
APPENDIX B SAMBA PROGRAMMING CABLE

UPC 23

UNIVERSAL PROTOCOL CONVERTER


USER MANUAL
APPENDIX C SUPPORTED BANK NOTE VALIDATORS
The UPC has been tested with the following bill acceptors
-

NV9
NV10
BV20
BV50
BV100
NV200

UPC 24

You might also like