Scribd
Upload
129 views58 pages

53 36765 ME591 2012 1 1 1 Analog Signal Conditionning

Analog signal conditioning circuits modify sensor or transducer outputs into a form that can be converted to digital data. There are two main types: passive circuits using components like resistors without external power, and active circuits using operational amplifiers which require power. Common active circuits include inverting and non-inverting amplifiers, filters, comparators, and sample-and-hold amplifiers. The goal is to amplify or modify signals, reduce noise, and ensure signals match the input range of data acquisition systems for optimal analog to digital conversion.

Uploaded by

Abhishek Kumbalur
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
129 views58 pages

53 36765 ME591 2012 1 1 1 Analog Signal Conditionning

Analog signal conditioning circuits modify sensor or transducer outputs into a form that can be converted to digital data. There are two main types: passive circuits using components like resistors without external power, and active circuits using operational amplifiers which require power. Common active circuits include inverting and non-inverting amplifiers, filters, comparators, and sample-and-hold amplifiers. The goal is to amplify or modify signals, reduce noise, and ensure signals match the input range of data acquisition systems for optimal analog to digital conversion.

Uploaded by

Abhishek Kumbalur
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 58

Analog Signal Conditioning

Analog and Digital Electronics

Electronics

Digital
Electronics

Analog
Electronics

Analog Electronics
Analog
Electronics
Operational
Amplifiers

741
LF351
TL084
LM324

Transistors

2N2222
2N3906
BC517
TIP 122
TIP 126

TRIAC

Thyristors
3

BTA600.40A

Analog Signal Conditioning

Types
Passive circuits
- Does not need power
- Resistance to voltage convergence
- Filtering

Active circuits
-

Requires outside power


Amplifications and filtering
Level shift
Filtering

Passive Circuits Amplification


Potential Divider
Convert the change in resistance into change in voltage
A load resistance is used to achieve the above goal as well as to limit the
current

Vs
I
Rl Rt

Vs
Vs
Vt
Rt I max
Rl Rt min
Rl Rt

Active Circuit Amplification


Operational Amplifiers (op-amp)
The primary purpose for the analog signal conditioning circuitry is to
modify the transducer or sensor output into a form that can be optimally
converted to a discrete time digital data stream by the data acquisition
system. Some important input requirements of most data acquisition
systems are:
The input signal must be a voltage waveform. The process of converting the

sensor output to a voltage can also be used to reduce unwanted signals,


that is noise.

The dynamic range of the input signal should be at or near the dynamic
range of the data acquisition system (usually equal to the voltage
reference level, Vref, or 2Vref). This is important in maximizing the
resolution of the analog to digital converter (ADC).
The source impedance, Zs , of the input signal should be low enough so that
changes in the input impedance, Zin, of the data acquisition system do not
affect the input signal.
The bandwidth of the input signal must be limited to less than half of the
sampling rate of the analog to digital conversion.

741 Op Amps pin-out

The ideal operational amplifier model

The op amp model: (a) open loop; (b) closed loop; (c) ideal.

The ideal op am model is based on the following assumptions:


it has infinite impedance at both inputs, consequently there is
no current drawn from the input circuits; I- = I+
it has infinite gain, hence the difference between the input
and output voltages is zero. This is denoted by short circuiting
the two inputs; V- = V+
it has zero output impedance, so that the output voltage is
independent of the output current.

Operational Amplifiers

Vout = A(V2 V1)


Vout = Output voltage.
A = Open-loop gain.
V1 = Inverting input.
V2 = Noninverting input.

10

Inverting Amplifier
Vout = -Vin ( Rf / Ri )

The inverting amplifier can amplify the signal with certain gain but with
inverting the polarity of the input signal.

14

Inverting Amplifiers

Non-inverting Amplifiers

The non-inverting amplifier can amplify the signal with


certain gain with the same polarity of the input signal.

Unity Gain Buffer

If RF=0 and Ri = 0 and is open (removed), then the gain of the


non-inverting amplifier is unity.

Buffer
Vout = Vin

The buffer can be used to keep the voltage level constant but increasing the
current (take the current from the power supply circuit)

18

The summing amplifier

The difference amplifier

The instrumentation amplifier


When the input signals are very low level and also have noise, the difference
amplifier is not able to extract a satisfactory difference signal. Possibly the
most important circuit configuration for amplifying sensor output when the
input signals are very low level is the instrumentation amplifier (IA). The
requirements for an instrumentation amplifier are as follows:
Finite, accurate and stable gain, usually between 1 and 1000.
Extremely high input impedance.
Extremely low output impedance.
Extremely high common mode rejection ratio (CMRR).

CMRR is the ratio of the gain of the amplifier for differentialmode signals (signals that are different between the two
inputs) to the gain of the amplifier for common-mode signals
(signals that are the same at both inputs).

Integrator amplifiers

The differentiator amplifier

Comparator

It takes analog sensor voltage and compares it to a threshold


voltage, Vref.
If the sensor's voltage is greater than the threshold, the
output of the circuit is maximum (typically 5 V).
If the sensor's output is less than the threshold, the output of
the circuit is minimum (usually OV).

Comparator
Vout = 5v if v+ > v= 0v if v+ < v-

The comparator can compare the input signal from a


sensor with a certain threshold to get 0v or 5v.
28

Comparator
Vout = 5v if v+ > v= 0v if v+ < v-

30

Effect of Noise

Sample and hold amplifier

The purpose of sample and hold circuitry is to take a snapshot of the


sensor signal and hold the value. An ADC must have a stable signal in
order to accurately perform a conversion.
The switch connects the capacitor to the signal conditioning circuit once
every sample period. The capacitor then holds the measured voltage until
a new sample is acquired. Often, the sample and hold circuit is
incorporated in the same integrated circuit package as the amplifier.

Problems with sample and hold amplifiers


Finite aperture time: The sample and hold takes a period of
time to capture a sample of the sensor signal. This is called
the aperture time. Since the signal will vary during this time,
so the sampled signal can be slightly inaccurate.
Signal feed through: When the sample and hold is not
connected to the signal, the value being held should remain
constant. Unfortunately, some signal does bleed through the
switch to the capacitor, causing the voltage being held to
change slightly.
Signal droop: The voltage being held on the capacitor starts to
slowly decrease over time if the signal is not sampled often
enough.

Logarithmic Operational Amplifier

Antilog Operational Amplifier

Filters
Types of filters
1- Low-pass filter
2- High-pass filter
3- Band-pass filter
4- Band-reject filter

Low-pass filter

High-pass filter

Active filters
The low-pass active filter

The high-pass active filter

The band-pass active filter

Voltage-to-current converter
i = v / R
o

i = output current
o

Vi = input voltage

Current-to-voltage converter

You might also like