Scribd
Upload
56 views28 pages

Network Devices

This document discusses various networking devices and their functions. It describes network interface cards (NICs) that connect devices to networks and add addressing. Repeaters and hubs extend network segments but don't filter, while bridges and switches can filter traffic using MAC addresses to limit collisions. Routers connect different network types and architectures, and determine optimal paths using routing tables. Gateways translate between different network protocols to allow communication. Each device has advantages like extending coverage or limiting traffic, and disadvantages like complexity, speed or cost.

Uploaded by

Ashin Antony
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
56 views28 pages

Network Devices

This document discusses various networking devices and their functions. It describes network interface cards (NICs) that connect devices to networks and add addressing. Repeaters and hubs extend network segments but don't filter, while bridges and switches can filter traffic using MAC addresses to limit collisions. Routers connect different network types and architectures, and determine optimal paths using routing tables. Gateways translate between different network protocols to allow communication. Each device has advantages like extending coverage or limiting traffic, and disadvantages like complexity, speed or cost.

Uploaded by

Ashin Antony
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 28

NETWORKING DEVICES

CONTENTS

Network Segments
NICs
Repeaters
Hubs
Bridges
Switches
Routers
Gateways
Advantages and Disadvantages

OSI MODEL
NODE B
Receiving Device

NODE A
Sending Device
Layer 7
Application Layer
Layer 6
Presentation Layer
Layer 5
Session Layer
Layer 4
Transport Layer
Layer 3
Network Layer
Layer 2
Data Link Layer
Layer 1
Physical Layer

Supports the communication between


applications over the network
Presents data to the receiver
in a form it recognises
Establishes a connection and
terminates it when no longer required
Acknowledges the flow of data
including re-transmission where required
Adds the appropriate network
addresses to packets

Adds the MAC addresses to packets

Transmits the data on the medium

Layer 7
Application Layer
Layer 6
Presentation Layer
Layer 5
Session Layer
Layer 4
Transport Layer
Layer 3
Network Layer
Layer 2
Data Link Layer
Layer 1
Physical Layer

MAC ADDRESS

Media Access Control address, a hardware address that


uniquely identifies each node of a network.

The Data Link Control (DLC) layer of the OSI


Reference Model is divided into two sublayers: the
Logical Link Control (LLC) layer and the Media
Access Control (MAC) layer.

The MAC layer interfaces directly with the network


medium. Consequently, each different type of network
medium requires a different MAC layer.

NETWORK SEGMENTS

Usually an area of a LAN

The area of the network bound by bridges or switches


where collisions are propagated, or the area bound by
a router to prevent the propagation of broadcasts

Dividing a network in to segments allows the majority


of traffic to stay remain local

NETWORK SEGMENTS
Switch

Hub
Hub
Hub

Segment 1

Segment 3
Segment 2

NETWORK INTERFACE CARD (NIC)

At source:
Receives the data packet from the Network Layer
Attaches its the MAC address to the data packet
Attaches the MAC address of the destination device
to the data packet
Converts data in to packets suitable for the particular
network (Ethernet, Token Ring, FDDI)
Converts packets in to electrical, light or radio
signals
Provides the physical connection to the media

NETWORK INTERFACE CARD (NIC)

As a destination device
Provides the physical connection to the media
Translates the signal in to data
Reads the MAC address to see if it matches its own
address
If it does match, passes the data to the Network
Layer

REPEATER

Allows the connection of segments, therefore extends the


network beyond the maximum length of a single segment

Functions at the Physical Layer of the OSI model

Connects segments of the same network, even if they use


different media

Has three basic functions


Receives a signal and cleans it
Re-times the signal to avoid collisions
Transmits the signal on to the next segment

HUB

A central point of a star topology

Allows the multiple connection of devices

Can be more than a basic Hub providing additional


services (Managed Hubs, Switched Hubs, Intelligent
Hubs)

In reality a Hub is a Repeater with multiple ports

Functions in a similar manner to a Repeater

HUB

Works at the Physical Layer of the OSI model

Passes data no matter which device it is addressed to

BRIDGE

Like a Repeater or Hub it connects segments

Works at Data Layer not Physical

Uses MAC address to make decisions

Acts as a filter, by determining whether or not to


forward a packet on to another segment

BRIDGE

Builds a Bridging Table, keeps track of devices on each


segment

Filters packets, does not forward them, by examining


their MAC address

It forwards packets whose destination address is on a


different segment from its own

It divides a network in to multiple collision domains


so reducing the number of collisions

COLLISION DOMAIN

A collision occurs when a station begins transmission


and then receives the beginning of a frame from another
station.

The station will immediately stop transmission and


issue a JAM signal onto the wire.

This will indicate to the other transmitting station that a


collision has occurred and both stations will back off
for a random amount of time and try to re-transmit

COLLISION DOMAIN

Collision Domain is defined as all the segments


between a pair of bridges or other layer 2 devices.

The reason for this is that all traffic must appear on all
the cables between bridges.

Thus if a frame is transmitted from a station on a


concentrator, all the stations on that concentrator will
see the frame at nearly the same time.

BRIDGE
Uses the Spanning Tree Protocol (STP) to decide whether to
pass a packet on to a different network segment

Bridge

A Transmits to
C, bridge will
not pass it to
Segment B

Segment A

D
B

G Transmits to
B, bridge will
pass it to
Segment A

Segment B

H
F

SWITCH

A multiport Bridge, functioning at the Data


Link Layer

Each port of the bridge decides whether to


forward data packets to the attached network

Keeps track of the MAC addresses of all


attached devices (just like a bridge)

Acts like a Hub, but filters like a Bridge

ROUTER

Works at Network Layer.

Can connect different network segments, if they are in the same


building or even on the opposite side of the globe

Work in LAN, MAN and WAN environments

Allows access to resources by selecting the best path

Can interconnect different networks Ethernet with Token Ring

Changes packet size and format to match the requirements of the


destination network

ROUTER

Two primary functions to determine the best path


and to share details of routes with other routers

Routing Table a database which keeps track of the


routes to networks and the associated costs

ROUTER

Static Routing routes are manually configured by a


network administrator

Dynamic Routing adjust automatically to changes in


network topology, and information it receives from
other routers

Routing Protocol uses a special algorithm to route


data across a network.

GATEWAY

Allows different networks to communicate by offering


a translation service from one protocol stack to
another

They work at all levels of the OSI model due to the


type of translation service they are providing

GATEWAY

Address Gateway connects networks using the same


protocol, but using different directory spaces such as
Message Handling Service

Protocol Gateway connects network using different


protocols. Translates source protocol so destination can
understand it

Application Gateway translates between applications


such as from an Internet email server to a messaging
server

Advantages & Disadvantages:


Repeater

Advantages

Can connect different types of media,


Can extend a network in terms of distance,
Does not increase network traffic

Disadvantages

Extends the collision domain,


Can not filter data,
Can not connect different network architectures,
Limited number only can be used in network

Advantages & Disadvantages:


Hub

Advantages

Cheap,
Can connect different media types

Disadvantages

Extends the collision domain,


Can not filter information,
Passes packets to all connected segments

Advantages & Disadvantages:


Bridge

Advantages

Limits the collision domain,


Can extend network distances,
Uses MAC address to filter traffic,
Eases congestion,
Can connect different types of media,
Some can connect differing architectures

Disadvantages

Broadcast packets can not be filtered,


More expensive than a repeater,
Slower than a repeater due to additional processing of
packets

Advantages & Disadvantages:


Switch

Advantages

Limits the collision domain,


Can provide bridging,
Can be configured to limit broadcast domain

Disadvantages

More expensive than a hub or bridge,


Configuration of additional functions can be very complex

Advantages & Disadvantages


Router

Advantages

Limits the collision domain,


Can function in LAN or WAN,
Connects differing media and architectures,
Can determine best path/route,
Can filter broadcasts

Disadvantages

Expensive,
Must use routable protocols,
Can be difficult to configure (static routing),
Slower than a bridge

THANK YOU

You might also like