Scribd
Upload
228 views

Lab Manual Hardware For Students PDF

The document is a lab manual containing instructions and objectives for experiments on a microwave communication trainer and RF amplifier. It describes the configuration and components of the MW-2000 system, including a transmitter, receiver, antennas and other blocks. It provides procedures for students to characterize the gain and return loss of an RF amplifier by measuring output power and return loss at various input frequencies using a spectrum analyzer and RF signal generator. Students are asked to record measurements in tables and plot the results. Similar procedures are given to characterize a detector circuit by measuring its output voltage for different input signal levels.

Uploaded by

Ghulam Shabbir
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
228 views

Lab Manual Hardware For Students PDF

The document is a lab manual containing instructions and objectives for experiments on a microwave communication trainer and RF amplifier. It describes the configuration and components of the MW-2000 system, including a transmitter, receiver, antennas and other blocks. It provides procedures for students to characterize the gain and return loss of an RF amplifier by measuring output power and return loss at various input frequencies using a spectrum analyzer and RF signal generator. Students are asked to record measurements in tables and plot the results. Similar procedures are given to characterize a detector circuit by measuring its output voltage for different input signal levels.

Uploaded by

Ghulam Shabbir
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 18

RF & MICROWAVE LAB MANUAL

LAB MANUAL 11

INTRODUCTION TO MICROWAVE
COMMUNICATION TRAINER
MW-2000 OVERVIEW:

Department of Telecommunication Engineering UET Taxila

RF & MICROWAVE LAB MANUAL

MW-2000 SYSTEM CONFIGURATION:

OBJECTIVES OF TRAINING:

Department of Telecommunication Engineering UET Taxila

RF & MICROWAVE LAB MANUAL

GENERAL FEATURES:

COMPONENTS:

Department of Telecommunication Engineering UET Taxila

RF & MICROWAVE LAB MANUAL

LAB ASSIGNMENT 11

INTRODUCTION TO MICROWAVE
COMMUNICATION TRAINER
1. Describe the exact range and a few applications of devices operating in the ISM band?
2. Draw the block diagram of the MW-2000 trainer in the complete communication system
configuration briefly elaborating the purpose of each block?

Department of Telecommunication Engineering UET Taxila

RF & MICROWAVE LAB MANUAL

LAB MANUAL 12

RF AMPLIFIER
Objectives:

Basic concepts:

Department of Telecommunication Engineering UET Taxila

RF & MICROWAVE LAB MANUAL

Stability:

Department of Telecommunication Engineering UET Taxila

RF & MICROWAVE LAB MANUAL

BY USING SPECTRUM ANALYSER AND RF SIGNAL GENERATOR AS TEST


INSTRUMENT.

Department of Telecommunication Engineering UET Taxila

RF & MICROWAVE LAB MANUAL

Procedure:

Department of Telecommunication Engineering UET Taxila

RF & MICROWAVE LAB MANUAL

Department of Telecommunication Engineering UET Taxila

RF & MICROWAVE LAB MANUAL

Record measuremants in the following table:


Frequency 2.2 2.24 2.28 2.3 2.34 2.38 2.4 2.42 2.44 2.46
GHz
Pin
dBm
Pr
dBm
RL
dB
Pout
dBm
Gain

RL=Pr[dBm] + 6dB+2dB Pin[dBm]


Gain= Pout[dBm] +1dB -Pin[dBm]+10dB

Then plot a graph between RL and frequency

Department of Telecommunication Engineering UET Taxila

10

RF & MICROWAVE LAB MANUAL

Costruct a new system

Department of Telecommunication Engineering UET Taxila

11

RF & MICROWAVE LAB MANUAL

And note down the measurements in following table:


Signal
generator
-24.5
-22.5
-20.5
-18.5
-16.5
-14.5
-12.5
-10.5
-8.5
-6.5
-4.5
-2.5
0.5
2.5
4.5

Pin[dBm]

Pout[dBm]

Department of Telecommunication Engineering UET Taxila

gain

12

RF & MICROWAVE LAB MANUAL

LAB ASSIGNMENT 12

RF AMPLIFIER
1. Paste all your reading tables and plots on your work book.

Department of Telecommunication Engineering UET Taxila

13

RF & MICROWAVE LAB MANUAL

LAB MANUAL 13

DETECTOR DESIGN
Objective:
To understand the theory and operation principles of Detectors.

Detector:
The simplest form of envelope detector is the diode detector. A diode detector is simply
a diode between the input and output of a circuit, connected to a resistor and capacitor in
parallel from the output of the circuit to the ground. If the resistor and capacitor are correctly
chosen, the output of this circuit should approximate a voltage-shifted version of the original
(baseband) signal. A simple filter can then be applied to filter out the DC component.

Department of Telecommunication Engineering UET Taxila

14

RF & MICROWAVE LAB MANUAL

Test instruments:

Procedure:

Department of Telecommunication Engineering UET Taxila

15

RF & MICROWAVE LAB MANUAL

Construct the following system:

Department of Telecommunication Engineering UET Taxila

16

RF & MICROWAVE LAB MANUAL

Record measuremants in the following table:


Frequency 2.2 2.24 2.28 2.3 2.34 2.38 2.4 2.42 2.44 2.46
GHz
Pin
dBm
Pr
dBm
RL
dB
RL=Pr[dBm] + 6dB+2dB Pin[dBm]

Then plot a graph between RL and frequency

Department of Telecommunication Engineering UET Taxila

17

RF & MICROWAVE LAB MANUAL

LAB ASSIGNMENT 13

DETECTOR
1. Paste all your reading tables and plots on your work book.

Department of Telecommunication Engineering UET Taxila

18

You might also like