----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
+============================================================+
| MIDAS(Modeling, Integrated Design & Analysis Software)
|
| midas Gen - Design & checking system for windows
|
+============================================================+
| RC-Member(Beam/Column/Brace/Wall) Analysis and Design
|
| Based On Eurocode2:04, Eurocode2, ACI318-11,
|
|
ACI318-08, ACI318-05, ACI318-02, ACI318-99,
|
|
ACI318-95, ACI318-89, NSR-10, CSA-A23.3-94,
|
|
BS8110-97
|
|
|
|
|
|
|
|
(c)SINCE 1989 |
+============================================================+
| MIDAS Information Technology Co.,Ltd.
(MIDAS IT) |
| MIDAS IT Design Development Team
|
+============================================================+
|
HomePage : www.MidasUser.com
|
+============================================================+
| Gen 2016
|
+============================================================+
*. DEFINITION OF LOAD COMBINATIONS WITH SCALING UP FACTORS.
------------------------------------------------------------------------------------LCB C
Loadcase Name(Factor) + Loadcase Name(Factor) + Loadcase Name(Fac
tor)
------------------------------------------------------------------------------------1 1
DL( 1.300) +
LL( 1.500)
2 1
DL( 1.300) +
LL( 1.500) +
WL-X( 0.
900)
3 1
DL( 1.300) +
LL( 1.500) +
WL-Y( 0.
900)
4 1
DL( 1.300) +
LL( 1.050) +
WL-X( 1.
500)
5 1
DL( 1.300) +
LL( 1.050) +
WL-Y( 1.
500)
6 1
DL( 1.300) +
LL( 1.500) +
WL-X(-0.
900)
7 1
DL( 1.300) +
LL( 1.500) +
WL-Y(-0.
900)
8 1
DL( 1.300) +
LL( 1.050) +
WL-X(-1.
500)
9 1
DL( 1.300) +
LL( 1.050) +
WL-Y(-1.
500)
10 1
DL( 1.000) +
LL( 0.300) +
EQ-X( 1.
000)
11 1
DL( 1.000) +
LL( 0.300) +
EQ-Y( 1.
000)

12 1

DL( 1.000) +

LL( 0.300) +

EQ-X(-1.

000)
13 1
DL( 1.000) +
LL( 0.300) +
EQ-Y(-1.
000)
-------------------------------------------------------------------------------------

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
13
*.DESCRIPTION OF BEAM DATA (iSEC =
2) : BEAM1
Section Type : Rectangle (RECT)
Beam Length (Span)
=
1.000 m.
Section Depth (Hc)
=
0.400 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
0.00 kN-m., LCB = 13
Negative Bending Moment N-Mu =
43.30 kN-m., LCB = 8
Shear Force
Vu =
82.16 kN. , LCB = 6
*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.342
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomin = 0.0000
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004)) =
-. Rhomax = k*Rho_et
=
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0059
-. Rhomin < Rho < Rhomax ---> O.K !

0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
52.97 kN-m.
47.67 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.000 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0073
0.0033
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0060
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
52.05 kN-m.
46.85 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.924 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute shear strength of concrete.
-. Vu
=
82.16 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
50.83 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
38.12 kN.
-. Vu > phiVc ---> Shear reinforcement is required.
( ). Compute required shear reinforcement. ( Av1 = 0.00008
-. Vs = (Vu-phiVc)/phi =
58.71 kN.
-. 4*SQRT(fc)*bw*d =
101.66 kN.
-. 8*SQRT(fc)*bw*d =
203.32 kN.
-. Vs < 4*SQRT(fc)*bw*d ---> O.K !
-. Avmin1 = 50*bw/fys
= 0.00025 m^2/m.
-. Avmin2 = 0.75*SQRT(fc)*bw/fys = 0.00021 m^2/m.
-. Avmin = MAX[ Avmin1, Avmin2 ] = 0.00025 m^2/m.
-. Avreq = Vs/(fys*d) = 0.00063 m^2/m.
-. Av
= MAX[ Avmin, Avreq ] = 0.00063 m^2/m.
-. N_leg = 2
-. Maximum spacing smax = MIN[ d/2, 24 in ] =
0.168
-. Calculate spacing s1 = N_leg*Av1 / Av
= 0.24816
-. Applied spacing s
= MIN[ smax, s1 ] =
0.168

m^2. )

m.
m.
m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
14
*.DESCRIPTION OF BEAM DATA (iSEC =
2) : BEAM1
Section Type : Rectangle (RECT)
Beam Length (Span)
=
1.000 m.
Section Depth (Hc)
=
0.400 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
0.00 kN-m., LCB = 13
Negative Bending Moment N-Mu =
51.39 kN-m., LCB = 8
Shear Force
Vu =
100.41 kN. , LCB = 6
*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.077
2- 1-P16
0.00060
Bottom
2
0.342
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomin = 0.0000
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004)) =
-. Rhomax = k*Rho_et
=
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0059
-. Rhomin < Rho < Rhomax ---> O.K !

0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
52.97 kN-m.
47.67 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.000 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0097
0.0033
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0093
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.071 m.
71.68 kN-m.
64.51 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.797 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute shear strength of concrete.
-. Vu
=
100.41 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
48.75 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
36.56 kN.
-. Vu > phiVc ---> Shear reinforcement is required.
( ). Compute required shear reinforcement. ( Av1 = 0.00008
-. Vs = (Vu-phiVc)/phi =
85.14 kN.
-. 4*SQRT(fc)*bw*d =
97.49 kN.
-. 8*SQRT(fc)*bw*d =
194.98 kN.
-. Vs < 4*SQRT(fc)*bw*d ---> O.K !
-. Avmin1 = 50*bw/fys
= 0.00025 m^2/m.
-. Avmin2 = 0.75*SQRT(fc)*bw/fys = 0.00021 m^2/m.
-. Avmin = MAX[ Avmin1, Avmin2 ] = 0.00025 m^2/m.
-. Avreq = Vs/(fys*d) = 0.00096 m^2/m.
-. Av
= MAX[ Avmin, Avreq ] = 0.00096 m^2/m.
-. N_leg = 2
-. Maximum spacing smax = MIN[ d/2, 24 in ] =
0.161
-. Calculate spacing s1 = N_leg*Av1 / Av
= 0.16412
-. Applied spacing s
= MIN[ smax, s1 ] =
0.161

m^2. )

m.
m.
m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
15
*.DESCRIPTION OF BEAM DATA (iSEC =
1) : BEAM2
Section Type : Rectangle (RECT)
Beam Length (Span)
=
4.100 m.
Section Depth (Hc)
=
0.300 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
7.71 kN-m., LCB =
Negative Bending Moment N-Mu =
12.54 kN-m., LCB =
Shear Force
Vu =
13.47 kN. , LCB =

4
8
8

*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.242
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0024
0.0024
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0083
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
36.33 kN-m.
32.70 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.236 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0085
-. Rhomin < Rho < Rhomax ---> O.K !

=
=
=
=
=

0.0033
0.0042
0.0033
0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
35.41 kN-m.
31.87 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.393 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================
( ). Compute shear strength of concrete.
-. Vu
=
13.47 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
35.72 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
26.79 kN.
-. phiVc/2 < Vu < phiVc ---> Minimum shear reinforcement is require
d.
( ). Compute required shear reinforcement. ( Av1 =
-. Avmin1 = 50*bw/fys
=2.500e-004
-. Avmin2 = 0.75*SQRT(fc)*bw/fys =2.054e-004
-. Av
= MAX[ Avmin1, Avmin2 ] =2.500e-004
-. N_leg = 2
-. Calculate spacing s1 = N_leg*Av1 / Av
-. Applied spacing s
= MIN[ s1, d/2, 24 in

0.00008 m^2. )
m^2/m.
m^2/m.
m^2/m.
=
] =

0.628 m.
0.118 m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
17
*.DESCRIPTION OF BEAM DATA (iSEC =
2) : BEAM1
Section Type : Rectangle (RECT)
Beam Length (Span)
=
3.050 m.
Section Depth (Hc)
=
0.400 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
5.48 kN-m., LCB =
Negative Bending Moment N-Mu =
10.83 kN-m., LCB =
Shear Force
Vu =
23.48 kN. , LCB =

9
5
5

*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.342
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0008
0.0008
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0059
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
52.97 kN-m.
47.67 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.115 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0060
-. Rhomin < Rho < Rhomax ---> O.K !

=
=
=
=
=

0.0033
0.0017
0.0017
0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
52.05 kN-m.
46.85 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.231 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================
( ). Compute shear strength of concrete.
-. Vu
=
23.48 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
50.83 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
38.12 kN.
-. phiVc/2 < Vu < phiVc ---> Minimum shear reinforcement is require
d.
( ). Compute required shear reinforcement. ( Av1 =
-. Avmin1 = 50*bw/fys
=2.500e-004
-. Avmin2 = 0.75*SQRT(fc)*bw/fys =2.054e-004
-. Av
= MAX[ Avmin1, Avmin2 ] =2.500e-004
-. N_leg = 2
-. Calculate spacing s1 = N_leg*Av1 / Av
-. Applied spacing s
= MIN[ s1, d/2, 24 in

0.00008 m^2. )
m^2/m.
m^2/m.
m^2/m.
=
] =

0.628 m.
0.168 m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
18
*.DESCRIPTION OF BEAM DATA (iSEC =
2) : BEAM1
Section Type : Rectangle (RECT)
Beam Length (Span)
=
3.150 m.
Section Depth (Hc)
=
0.400 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
4.95 kN-m., LCB =
Negative Bending Moment N-Mu =
16.83 kN-m., LCB =
Shear Force
Vu =
32.26 kN. , LCB =

9
5
3

*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.342
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0008
0.0008
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0059
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
52.97 kN-m.
47.67 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.104 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0060
-. Rhomin < Rho < Rhomax ---> O.K !

=
=
=
=
=

0.0033
0.0027
0.0027
0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
52.05 kN-m.
46.85 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.359 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================
( ). Compute shear strength of concrete.
-. Vu
=
32.26 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
50.83 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
38.12 kN.
-. phiVc/2 < Vu < phiVc ---> Minimum shear reinforcement is require
d.
( ). Compute required shear reinforcement. ( Av1 =
-. Avmin1 = 50*bw/fys
=2.500e-004
-. Avmin2 = 0.75*SQRT(fc)*bw/fys =2.054e-004
-. Av
= MAX[ Avmin1, Avmin2 ] =2.500e-004
-. N_leg = 2
-. Calculate spacing s1 = N_leg*Av1 / Av
-. Applied spacing s
= MIN[ s1, d/2, 24 in

0.00008 m^2. )
m^2/m.
m^2/m.
m^2/m.
=
] =

0.628 m.
0.168 m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
21
*.DESCRIPTION OF BEAM DATA (iSEC =
2) : BEAM1
Section Type : Rectangle (RECT)
Beam Length (Span)
=
3.050 m.
Section Depth (Hc)
=
0.400 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
5.73 kN-m., LCB =
Negative Bending Moment N-Mu =
19.70 kN-m., LCB =
Shear Force
Vu =
36.39 kN. , LCB =

9
5
3

*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.342
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0009
0.0009
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0059
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
52.97 kN-m.
47.67 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.120 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0060
-. Rhomin < Rho < Rhomax ---> O.K !

=
=
=
=
=

0.0033
0.0032
0.0032
0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
52.05 kN-m.
46.85 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.421 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================
( ). Compute shear strength of concrete.
-. Vu
=
36.39 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
50.83 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
38.12 kN.
-. phiVc/2 < Vu < phiVc ---> Minimum shear reinforcement is require
d.
( ). Compute required shear reinforcement. ( Av1 =
-. Avmin1 = 50*bw/fys
=2.500e-004
-. Avmin2 = 0.75*SQRT(fc)*bw/fys =2.054e-004
-. Av
= MAX[ Avmin1, Avmin2 ] =2.500e-004
-. N_leg = 2
-. Calculate spacing s1 = N_leg*Av1 / Av
-. Applied spacing s
= MIN[ s1, d/2, 24 in

0.00008 m^2. )
m^2/m.
m^2/m.
m^2/m.
=
] =

0.628 m.
0.168 m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
22
*.DESCRIPTION OF BEAM DATA (iSEC =
2) : BEAM1
Section Type : Rectangle (RECT)
Beam Length (Span)
=
3.150 m.
Section Depth (Hc)
=
0.400 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
4.92 kN-m., LCB =
Negative Bending Moment N-Mu =
22.70 kN-m., LCB =
Shear Force
Vu =
39.50 kN. , LCB =

9
5
3

*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.342
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0008
0.0008
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0059
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
52.97 kN-m.
47.67 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.103 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0060
-. Rhomin < Rho < Rhomax ---> O.K !

=
=
=
=
=

0.0033
0.0037
0.0033
0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
52.05 kN-m.
46.85 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.485 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================
( ). Compute shear strength of concrete.
-. Vu
=
39.50 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
50.83 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
38.12 kN.
-. Vu > phiVc ---> Shear reinforcement is required.
( ). Compute required shear reinforcement. ( Av1 = 0.00008
-. Vs = (Vu-phiVc)/phi =
1.84 kN.
-. 4*SQRT(fc)*bw*d =
101.66 kN.
-. 8*SQRT(fc)*bw*d =
203.32 kN.
-. Vs < 4*SQRT(fc)*bw*d ---> O.K !
-. Avmin1 = 50*bw/fys
= 0.00025 m^2/m.
-. Avmin2 = 0.75*SQRT(fc)*bw/fys = 0.00021 m^2/m.
-. Avmin = MAX[ Avmin1, Avmin2 ] = 0.00025 m^2/m.
-. Avreq = Vs/(fys*d) = 0.00002 m^2/m.
-. Av
= MAX[ Avmin, Avreq ] = 0.00025 m^2/m.
-. N_leg = 2
-. Maximum spacing smax = MIN[ d/2, 24 in ] =
0.168
-. Calculate spacing s1 = N_leg*Av1 / Av
= 0.62800
-. Applied spacing s
= MIN[ smax, s1 ] =
0.168

m^2. )

m.
m.
m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
23
*.DESCRIPTION OF BEAM DATA (iSEC =
2) : BEAM1
Section Type : Rectangle (RECT)
Beam Length (Span)
=
2.763 m.
Section Depth (Hc)
=
0.400 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
3.88 kN-m., LCB =
Negative Bending Moment N-Mu =
18.29 kN-m., LCB =
Shear Force
Vu =
33.98 kN. , LCB =

9
5
3

*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.342
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0006
0.0006
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0059
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
52.97 kN-m.
47.67 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.081 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0060
-. Rhomin < Rho < Rhomax ---> O.K !

=
=
=
=
=

0.0033
0.0030
0.0030
0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
52.05 kN-m.
46.85 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.390 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================
( ). Compute shear strength of concrete.
-. Vu
=
33.98 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
50.83 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
38.12 kN.
-. phiVc/2 < Vu < phiVc ---> Minimum shear reinforcement is require
d.
( ). Compute required shear reinforcement. ( Av1 =
-. Avmin1 = 50*bw/fys
=2.500e-004
-. Avmin2 = 0.75*SQRT(fc)*bw/fys =2.054e-004
-. Av
= MAX[ Avmin1, Avmin2 ] =2.500e-004
-. N_leg = 2
-. Calculate spacing s1 = N_leg*Av1 / Av
-. Applied spacing s
= MIN[ s1, d/2, 24 in

0.00008 m^2. )
m^2/m.
m^2/m.
m^2/m.
=
] =

0.628 m.
0.168 m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
24
*.DESCRIPTION OF BEAM DATA (iSEC =
2) : BEAM1
Section Type : Rectangle (RECT)
Beam Length (Span)
=
1.000 m.
Section Depth (Hc)
=
0.400 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
0.00 kN-m., LCB = 13
Negative Bending Moment N-Mu =
41.11 kN-m., LCB = 8
Shear Force
Vu =
75.45 kN. , LCB = 8
*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.342
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomin = 0.0000
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004)) =
-. Rhomax = k*Rho_et
=
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0059
-. Rhomin < Rho < Rhomax ---> O.K !

0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
52.97 kN-m.
47.67 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.000 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0069
0.0033
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0060
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
52.05 kN-m.
46.85 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.878 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute shear strength of concrete.
-. Vu
=
75.45 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
50.83 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
38.12 kN.
-. Vu > phiVc ---> Shear reinforcement is required.
( ). Compute required shear reinforcement. ( Av1 = 0.00008
-. Vs = (Vu-phiVc)/phi =
49.77 kN.
-. 4*SQRT(fc)*bw*d =
101.66 kN.
-. 8*SQRT(fc)*bw*d =
203.32 kN.
-. Vs < 4*SQRT(fc)*bw*d ---> O.K !
-. Avmin1 = 50*bw/fys
= 0.00025 m^2/m.
-. Avmin2 = 0.75*SQRT(fc)*bw/fys = 0.00021 m^2/m.
-. Avmin = MAX[ Avmin1, Avmin2 ] = 0.00025 m^2/m.
-. Avreq = Vs/(fys*d) = 0.00054 m^2/m.
-. Av
= MAX[ Avmin, Avreq ] = 0.00054 m^2/m.
-. N_leg = 2
-. Maximum spacing smax = MIN[ d/2, 24 in ] =
0.168
-. Calculate spacing s1 = N_leg*Av1 / Av
= 0.29277
-. Applied spacing s
= MIN[ smax, s1 ] =
0.168

m^2. )

m.
m.
m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
26
*.DESCRIPTION OF BEAM DATA (iSEC =
1) : BEAM2
Section Type : Rectangle (RECT)
Beam Length (Span)
=
1.113 m.
Section Depth (Hc)
=
0.300 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
5.97 kN-m., LCB = 9
Negative Bending Moment N-Mu =
0.00 kN-m., LCB = 13
Shear Force
Vu =
14.69 kN. , LCB = 9
*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.242
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0019
0.0019
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0083
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
36.33 kN-m.
32.70 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.183 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomin = 0.0000
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004)) =
-. Rhomax = k*Rho_et
=

0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0085
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
35.41 kN-m.
31.87 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.000 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute shear strength of concrete.
-. Vu
=
14.69 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
36.56 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
27.42 kN.
-. phiVc/2 < Vu < phiVc ---> Minimum shear reinforcement is require
d.
( ). Compute required shear reinforcement. ( Av1 =
-. Avmin1 = 50*bw/fys
=2.500e-004
-. Avmin2 = 0.75*SQRT(fc)*bw/fys =2.054e-004
-. Av
= MAX[ Avmin1, Avmin2 ] =2.500e-004
-. N_leg = 2
-. Calculate spacing s1 = N_leg*Av1 / Av
-. Applied spacing s
= MIN[ s1, d/2, 24 in

0.00008 m^2. )
m^2/m.
m^2/m.
m^2/m.
=
] =

0.628 m.
0.121 m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
27
*.DESCRIPTION OF BEAM DATA (iSEC =
5) : BEAM3
Section Type : Rectangle (RECT)
Beam Length (Span)
=
3.050 m.
Section Depth (Hc)
=
0.300 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
3.84 kN-m., LCB =
Negative Bending Moment N-Mu =
3.50 kN-m., LCB =
Shear Force
Vu =
11.17 kN. , LCB =

6
2
3

*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.242
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0012
0.0012
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0083
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
36.33 kN-m.
32.70 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.117 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0085
-. Rhomin < Rho < Rhomax ---> O.K !

=
=
=
=
=

0.0033
0.0011
0.0011
0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
35.41 kN-m.
31.87 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.110 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================
( ). Compute shear strength of concrete.
-. Vu
=
11.17 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
36.56 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
27.42 kN.
-. Vu < phiVc/2 ---> Shear reinforcement is not required.
( ). Compute required shear reinforcement.
-. Applied spacing s
= MIN[ d/2, 24 in ] =

0.121 m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
29
*.DESCRIPTION OF BEAM DATA (iSEC =
5) : BEAM3
Section Type : Rectangle (RECT)
Beam Length (Span)
=
2.763 m.
Section Depth (Hc)
=
0.300 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
1.71 kN-m., LCB =
Negative Bending Moment N-Mu =
22.26 kN-m., LCB =
Shear Force
Vu =
42.02 kN. , LCB =

7
3
3

*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.242
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0005
0.0005
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0083
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
36.33 kN-m.
32.70 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.052 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0085
-. Rhomin < Rho < Rhomax ---> O.K !

=
=
=
=
=

0.0033
0.0076
0.0033
0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
35.41 kN-m.
31.87 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.698 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================
( ). Compute shear strength of concrete.
-. Vu
=
42.02 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
35.72 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
26.79 kN.
-. Vu > phiVc ---> Shear reinforcement is required.
( ). Compute required shear reinforcement. ( Av1 = 0.00008
-. Vs = (Vu-phiVc)/phi =
20.31 kN.
-. 4*SQRT(fc)*bw*d =
71.45 kN.
-. 8*SQRT(fc)*bw*d =
142.90 kN.
-. Vs < 4*SQRT(fc)*bw*d ---> O.K !
-. Avmin1 = 50*bw/fys
= 0.00025 m^2/m.
-. Avmin2 = 0.75*SQRT(fc)*bw/fys = 0.00021 m^2/m.
-. Avmin = MAX[ Avmin1, Avmin2 ] = 0.00025 m^2/m.
-. Avreq = Vs/(fys*d) = 0.00031 m^2/m.
-. Av
= MAX[ Avmin, Avreq ] = 0.00031 m^2/m.
-. N_leg = 2
-. Maximum spacing smax = MIN[ d/2, 24 in ] =
0.118
-. Calculate spacing s1 = N_leg*Av1 / Av
= 0.50425
-. Applied spacing s
= MIN[ smax, s1 ] =
0.118

m^2. )

m.
m.
m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
31
*.DESCRIPTION OF BEAM DATA (iSEC =
2) : BEAM1
Section Type : Rectangle (RECT)
Beam Length (Span)
=
3.100 m.
Section Depth (Hc)
=
0.400 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
40.72 kN-m., LCB = 4
Negative Bending Moment N-Mu =
0.00 kN-m., LCB = 13
Shear Force
Vu =
14.91 kN. , LCB = 8
*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.342
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0066
0.0033
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0059
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
52.97 kN-m.
47.67 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.854 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomin = 0.0000
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004)) =
-. Rhomax = k*Rho_et
=

0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0060
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
52.05 kN-m.
46.85 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.000 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute shear strength of concrete.
-. Vu
=
14.91 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
51.66 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
38.75 kN.
-. Vu < phiVc/2 ---> Shear reinforcement is not required.
( ). Compute required shear reinforcement.
-. Applied spacing s
= MIN[ d/2, 24 in ] =

0.171 m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
32
*.DESCRIPTION OF BEAM DATA (iSEC =
2) : BEAM1
Section Type : Rectangle (RECT)
Beam Length (Span)
=
3.100 m.
Section Depth (Hc)
=
0.400 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
49.36 kN-m., LCB = 4
Negative Bending Moment N-Mu =
0.00 kN-m., LCB = 13
Shear Force
Vu =
14.70 kN. , LCB = 4
*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.328
2- 1-P16
0.00060
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0089
0.0033
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0092
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.071 m.
73.05 kN-m.
65.75 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.751 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomin = 0.0000
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004)) =
-. Rhomax = k*Rho_et
=

0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0060
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
52.05 kN-m.
46.85 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.000 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute shear strength of concrete.
-. Vu
=
14.70 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
49.58 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
37.18 kN.
-. Vu < phiVc/2 ---> Shear reinforcement is not required.
( ). Compute required shear reinforcement.
-. Applied spacing s
= MIN[ d/2, 24 in ] =

0.164 m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
33
*.DESCRIPTION OF BEAM DATA (iSEC =
2) : BEAM1
Section Type : Rectangle (RECT)
Beam Length (Span)
=
3.100 m.
Section Depth (Hc)
=
0.400 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
34.53 kN-m., LCB = 4
Negative Bending Moment N-Mu =
0.00 kN-m., LCB = 13
Shear Force
Vu =
27.71 kN. , LCB = 8
*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.342
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0056
0.0033
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0059
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
52.97 kN-m.
47.67 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.724 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomin = 0.0000
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004)) =
-. Rhomax = k*Rho_et
=

0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0060
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
52.05 kN-m.
46.85 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.000 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute shear strength of concrete.
-. Vu
=
27.71 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
51.66 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
38.75 kN.
-. phiVc/2 < Vu < phiVc ---> Minimum shear reinforcement is require
d.
( ). Compute required shear reinforcement. ( Av1 =
-. Avmin1 = 50*bw/fys
=2.500e-004
-. Avmin2 = 0.75*SQRT(fc)*bw/fys =2.054e-004
-. Av
= MAX[ Avmin1, Avmin2 ] =2.500e-004
-. N_leg = 2
-. Calculate spacing s1 = N_leg*Av1 / Av
-. Applied spacing s
= MIN[ s1, d/2, 24 in

0.00008 m^2. )
m^2/m.
m^2/m.
m^2/m.
=
] =

0.628 m.
0.171 m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
44
*.DESCRIPTION OF BEAM DATA (iSEC =
3) : ROOF BEAM
Section Type : Rectangle (RECT)
Beam Length (Span)
=
2.775 m.
Section Depth (Hc)
=
0.350 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
5.62 kN-m., LCB =
Negative Bending Moment N-Mu =
10.85 kN-m., LCB =
Shear Force
Vu =
29.77 kN. , LCB =

9
5
5

*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.292
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0012
0.0012
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0069
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
44.65 kN-m.
40.18 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.140 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0070
-. Rhomin < Rho < Rhomax ---> O.K !

=
=
=
=
=

0.0033
0.0024
0.0024
0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
43.73 kN-m.
39.36 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.276 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================
( ). Compute shear strength of concrete.
-. Vu
=
29.77 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
43.28 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
32.46 kN.
-. phiVc/2 < Vu < phiVc ---> Minimum shear reinforcement is require
d.
( ). Compute required shear reinforcement. ( Av1 =
-. Avmin1 = 50*bw/fys
=2.500e-004
-. Avmin2 = 0.75*SQRT(fc)*bw/fys =2.054e-004
-. Av
= MAX[ Avmin1, Avmin2 ] =2.500e-004
-. N_leg = 2
-. Calculate spacing s1 = N_leg*Av1 / Av
-. Applied spacing s
= MIN[ s1, d/2, 24 in

0.00008 m^2. )
m^2/m.
m^2/m.
m^2/m.
=
] =

0.628 m.
0.143 m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
45
*.DESCRIPTION OF BEAM DATA (iSEC =
3) : ROOF BEAM
Section Type : Rectangle (RECT)
Beam Length (Span)
=
3.050 m.
Section Depth (Hc)
=
0.350 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
4.50 kN-m., LCB =
Negative Bending Moment N-Mu =
16.00 kN-m., LCB =
Shear Force
Vu =
34.11 kN. , LCB =

9
5
5

*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.292
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0010
0.0010
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0069
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
44.65 kN-m.
40.18 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.112 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0070
-. Rhomin < Rho < Rhomax ---> O.K !

=
=
=
=
=

0.0033
0.0036
0.0033
0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
43.73 kN-m.
39.36 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.406 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================
( ). Compute shear strength of concrete.
-. Vu
=
34.11 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
43.28 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
32.46 kN.
-. Vu > phiVc ---> Shear reinforcement is required.
( ). Compute required shear reinforcement. ( Av1 = 0.00008
-. Vs = (Vu-phiVc)/phi =
2.21 kN.
-. 4*SQRT(fc)*bw*d =
86.56 kN.
-. 8*SQRT(fc)*bw*d =
173.11 kN.
-. Vs < 4*SQRT(fc)*bw*d ---> O.K !
-. Avmin1 = 50*bw/fys
= 0.00025 m^2/m.
-. Avmin2 = 0.75*SQRT(fc)*bw/fys = 0.00021 m^2/m.
-. Avmin = MAX[ Avmin1, Avmin2 ] = 0.00025 m^2/m.
-. Avreq = Vs/(fys*d) = 0.00003 m^2/m.
-. Av
= MAX[ Avmin, Avreq ] = 0.00025 m^2/m.
-. N_leg = 2
-. Maximum spacing smax = MIN[ d/2, 24 in ] =
0.143
-. Calculate spacing s1 = N_leg*Av1 / Av
= 0.62800
-. Applied spacing s
= MIN[ smax, s1 ] =
0.143

m^2. )

m.
m.
m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
46
*.DESCRIPTION OF BEAM DATA (iSEC =
3) : ROOF BEAM
Section Type : Rectangle (RECT)
Beam Length (Span)
=
3.150 m.
Section Depth (Hc)
=
0.350 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
3.45 kN-m., LCB =
Negative Bending Moment N-Mu =
19.81 kN-m., LCB =
Shear Force
Vu =
37.07 kN. , LCB =

9
5
5

*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.292
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0007
0.0007
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0069
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
44.65 kN-m.
40.18 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.086 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0070
-. Rhomin < Rho < Rhomax ---> O.K !

=
=
=
=
=

0.0033
0.0045
0.0033
0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
43.73 kN-m.
39.36 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.503 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================
( ). Compute shear strength of concrete.
-. Vu
=
37.07 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
43.28 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
32.46 kN.
-. Vu > phiVc ---> Shear reinforcement is required.
( ). Compute required shear reinforcement. ( Av1 = 0.00008
-. Vs = (Vu-phiVc)/phi =
6.15 kN.
-. 4*SQRT(fc)*bw*d =
86.56 kN.
-. 8*SQRT(fc)*bw*d =
173.11 kN.
-. Vs < 4*SQRT(fc)*bw*d ---> O.K !
-. Avmin1 = 50*bw/fys
= 0.00025 m^2/m.
-. Avmin2 = 0.75*SQRT(fc)*bw/fys = 0.00021 m^2/m.
-. Avmin = MAX[ Avmin1, Avmin2 ] = 0.00025 m^2/m.
-. Avreq = Vs/(fys*d) = 0.00008 m^2/m.
-. Av
= MAX[ Avmin, Avreq ] = 0.00025 m^2/m.
-. N_leg = 2
-. Maximum spacing smax = MIN[ d/2, 24 in ] =
0.143
-. Calculate spacing s1 = N_leg*Av1 / Av
= 0.62800
-. Applied spacing s
= MIN[ smax, s1 ] =
0.143

m^2. )

m.
m.
m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
47
*.DESCRIPTION OF BEAM DATA (iSEC =
3) : ROOF BEAM
Section Type : Rectangle (RECT)
Beam Length (Span)
=
2.763 m.
Section Depth (Hc)
=
0.350 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
2.14 kN-m., LCB =
Negative Bending Moment N-Mu =
17.91 kN-m., LCB =
Shear Force
Vu =
35.00 kN. , LCB =

9
5
5

*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.292
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0005
0.0005
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0069
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
44.65 kN-m.
40.18 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.053 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0070
-. Rhomin < Rho < Rhomax ---> O.K !

=
=
=
=
=

0.0033
0.0041
0.0033
0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
43.73 kN-m.
39.36 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.455 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================
( ). Compute shear strength of concrete.
-. Vu
=
35.00 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
43.28 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
32.46 kN.
-. Vu > phiVc ---> Shear reinforcement is required.
( ). Compute required shear reinforcement. ( Av1 = 0.00008
-. Vs = (Vu-phiVc)/phi =
3.39 kN.
-. 4*SQRT(fc)*bw*d =
86.56 kN.
-. 8*SQRT(fc)*bw*d =
173.11 kN.
-. Vs < 4*SQRT(fc)*bw*d ---> O.K !
-. Avmin1 = 50*bw/fys
= 0.00025 m^2/m.
-. Avmin2 = 0.75*SQRT(fc)*bw/fys = 0.00021 m^2/m.
-. Avmin = MAX[ Avmin1, Avmin2 ] = 0.00025 m^2/m.
-. Avreq = Vs/(fys*d) = 0.00004 m^2/m.
-. Av
= MAX[ Avmin, Avreq ] = 0.00025 m^2/m.
-. N_leg = 2
-. Maximum spacing smax = MIN[ d/2, 24 in ] =
0.143
-. Calculate spacing s1 = N_leg*Av1 / Av
= 0.62800
-. Applied spacing s
= MIN[ smax, s1 ] =
0.143

m^2. )

m.
m.
m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
49
*.DESCRIPTION OF BEAM DATA (iSEC =
3) : ROOF BEAM
Section Type : Rectangle (RECT)
Beam Length (Span)
=
3.050 m.
Section Depth (Hc)
=
0.350 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
5.42 kN-m., LCB =
Negative Bending Moment N-Mu =
14.50 kN-m., LCB =
Shear Force
Vu =
33.47 kN. , LCB =

9
5
5

*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.292
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0011
0.0011
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0069
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
44.65 kN-m.
40.18 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.135 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0070
-. Rhomin < Rho < Rhomax ---> O.K !

=
=
=
=
=

0.0033
0.0033
0.0033
0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
43.73 kN-m.
39.36 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.368 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================
( ). Compute shear strength of concrete.
-. Vu
=
33.47 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
43.28 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
32.46 kN.
-. Vu > phiVc ---> Shear reinforcement is required.
( ). Compute required shear reinforcement. ( Av1 = 0.00008
-. Vs = (Vu-phiVc)/phi =
1.36 kN.
-. 4*SQRT(fc)*bw*d =
86.56 kN.
-. 8*SQRT(fc)*bw*d =
173.11 kN.
-. Vs < 4*SQRT(fc)*bw*d ---> O.K !
-. Avmin1 = 50*bw/fys
= 0.00025 m^2/m.
-. Avmin2 = 0.75*SQRT(fc)*bw/fys = 0.00021 m^2/m.
-. Avmin = MAX[ Avmin1, Avmin2 ] = 0.00025 m^2/m.
-. Avreq = Vs/(fys*d) = 0.00002 m^2/m.
-. Av
= MAX[ Avmin, Avreq ] = 0.00025 m^2/m.
-. N_leg = 2
-. Maximum spacing smax = MIN[ d/2, 24 in ] =
0.143
-. Calculate spacing s1 = N_leg*Av1 / Av
= 0.62800
-. Applied spacing s
= MIN[ smax, s1 ] =
0.143

m^2. )

m.
m.
m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
50
*.DESCRIPTION OF BEAM DATA (iSEC =
3) : ROOF BEAM
Section Type : Rectangle (RECT)
Beam Length (Span)
=
3.150 m.
Section Depth (Hc)
=
0.350 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
3.39 kN-m., LCB =
Negative Bending Moment N-Mu =
19.88 kN-m., LCB =
Shear Force
Vu =
37.18 kN. , LCB =

9
5
5

*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.292
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0007
0.0007
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0069
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
44.65 kN-m.
40.18 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.084 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0070
-. Rhomin < Rho < Rhomax ---> O.K !

=
=
=
=
=

0.0033
0.0045
0.0033
0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
43.73 kN-m.
39.36 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.505 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================
( ). Compute shear strength of concrete.
-. Vu
=
37.18 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
43.28 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
32.46 kN.
-. Vu > phiVc ---> Shear reinforcement is required.
( ). Compute required shear reinforcement. ( Av1 = 0.00008
-. Vs = (Vu-phiVc)/phi =
6.30 kN.
-. 4*SQRT(fc)*bw*d =
86.56 kN.
-. 8*SQRT(fc)*bw*d =
173.11 kN.
-. Vs < 4*SQRT(fc)*bw*d ---> O.K !
-. Avmin1 = 50*bw/fys
= 0.00025 m^2/m.
-. Avmin2 = 0.75*SQRT(fc)*bw/fys = 0.00021 m^2/m.
-. Avmin = MAX[ Avmin1, Avmin2 ] = 0.00025 m^2/m.
-. Avreq = Vs/(fys*d) = 0.00008 m^2/m.
-. Av
= MAX[ Avmin, Avreq ] = 0.00025 m^2/m.
-. N_leg = 2
-. Maximum spacing smax = MIN[ d/2, 24 in ] =
0.143
-. Calculate spacing s1 = N_leg*Av1 / Av
= 0.62800
-. Applied spacing s
= MIN[ smax, s1 ] =
0.143

m^2. )

m.
m.
m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
51
*.DESCRIPTION OF BEAM DATA (iSEC =
3) : ROOF BEAM
Section Type : Rectangle (RECT)
Beam Length (Span)
=
2.763 m.
Section Depth (Hc)
=
0.350 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
2.20 kN-m., LCB =
Negative Bending Moment N-Mu =
17.68 kN-m., LCB =
Shear Force
Vu =
34.86 kN. , LCB =

9
5
5

*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.292
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0005
0.0005
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0069
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
44.65 kN-m.
40.18 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.055 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0070
-. Rhomin < Rho < Rhomax ---> O.K !

=
=
=
=
=

0.0033
0.0040
0.0033
0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
43.73 kN-m.
39.36 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.449 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================
( ). Compute shear strength of concrete.
-. Vu
=
34.86 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
43.28 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
32.46 kN.
-. Vu > phiVc ---> Shear reinforcement is required.
( ). Compute required shear reinforcement. ( Av1 = 0.00008
-. Vs = (Vu-phiVc)/phi =
3.20 kN.
-. 4*SQRT(fc)*bw*d =
86.56 kN.
-. 8*SQRT(fc)*bw*d =
173.11 kN.
-. Vs < 4*SQRT(fc)*bw*d ---> O.K !
-. Avmin1 = 50*bw/fys
= 0.00025 m^2/m.
-. Avmin2 = 0.75*SQRT(fc)*bw/fys = 0.00021 m^2/m.
-. Avmin = MAX[ Avmin1, Avmin2 ] = 0.00025 m^2/m.
-. Avreq = Vs/(fys*d) = 0.00004 m^2/m.
-. Av
= MAX[ Avmin, Avreq ] = 0.00025 m^2/m.
-. N_leg = 2
-. Maximum spacing smax = MIN[ d/2, 24 in ] =
0.143
-. Calculate spacing s1 = N_leg*Av1 / Av
= 0.62800
-. Applied spacing s
= MIN[ smax, s1 ] =
0.143

m^2. )

m.
m.
m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
53
*.DESCRIPTION OF BEAM DATA (iSEC =
3) : ROOF BEAM
Section Type : Rectangle (RECT)
Beam Length (Span)
=
2.050 m.
Section Depth (Hc)
=
0.350 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
0.00 kN-m., LCB = 13
Negative Bending Moment N-Mu =
37.87 kN-m., LCB = 8
Shear Force
Vu =
44.17 kN. , LCB = 8
*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.292
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomin = 0.0000
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004)) =
-. Rhomax = k*Rho_et
=
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0069
-. Rhomin < Rho < Rhomax ---> O.K !

0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
44.65 kN-m.
40.18 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.000 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0090
0.0033
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0070
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
43.73 kN-m.
39.36 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.962 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute shear strength of concrete.
-. Vu
=
44.17 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
43.28 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
32.46 kN.
-. Vu > phiVc ---> Shear reinforcement is required.
( ). Compute required shear reinforcement. ( Av1 = 0.00008
-. Vs = (Vu-phiVc)/phi =
15.62 kN.
-. 4*SQRT(fc)*bw*d =
86.56 kN.
-. 8*SQRT(fc)*bw*d =
173.11 kN.
-. Vs < 4*SQRT(fc)*bw*d ---> O.K !
-. Avmin1 = 50*bw/fys
= 0.00025 m^2/m.
-. Avmin2 = 0.75*SQRT(fc)*bw/fys = 0.00021 m^2/m.
-. Avmin = MAX[ Avmin1, Avmin2 ] = 0.00025 m^2/m.
-. Avreq = Vs/(fys*d) = 0.00020 m^2/m.
-. Av
= MAX[ Avmin, Avreq ] = 0.00025 m^2/m.
-. N_leg = 2
-. Maximum spacing smax = MIN[ d/2, 24 in ] =
0.143
-. Calculate spacing s1 = N_leg*Av1 / Av
= 0.62800
-. Applied spacing s
= MIN[ smax, s1 ] =
0.143

m^2. )

m.
m.
m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
54
*.DESCRIPTION OF BEAM DATA (iSEC =
3) : ROOF BEAM
Section Type : Rectangle (RECT)
Beam Length (Span)
=
2.050 m.
Section Depth (Hc)
=
0.350 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
0.00 kN-m., LCB = 13
Negative Bending Moment N-Mu =
38.78 kN-m., LCB = 8
Shear Force
Vu =
45.53 kN. , LCB = 8
*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.292
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomin = 0.0000
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004)) =
-. Rhomax = k*Rho_et
=
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0069
-. Rhomin < Rho < Rhomax ---> O.K !

0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
44.65 kN-m.
40.18 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.000 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0092
0.0033
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0070
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
43.73 kN-m.
39.36 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.985 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute shear strength of concrete.
-. Vu
=
45.53 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
43.28 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
32.46 kN.
-. Vu > phiVc ---> Shear reinforcement is required.
( ). Compute required shear reinforcement. ( Av1 = 0.00008
-. Vs = (Vu-phiVc)/phi =
17.43 kN.
-. 4*SQRT(fc)*bw*d =
86.56 kN.
-. 8*SQRT(fc)*bw*d =
173.11 kN.
-. Vs < 4*SQRT(fc)*bw*d ---> O.K !
-. Avmin1 = 50*bw/fys
= 0.00025 m^2/m.
-. Avmin2 = 0.75*SQRT(fc)*bw/fys = 0.00021 m^2/m.
-. Avmin = MAX[ Avmin1, Avmin2 ] = 0.00025 m^2/m.
-. Avreq = Vs/(fys*d) = 0.00022 m^2/m.
-. Av
= MAX[ Avmin, Avreq ] = 0.00025 m^2/m.
-. N_leg = 2
-. Maximum spacing smax = MIN[ d/2, 24 in ] =
0.143
-. Calculate spacing s1 = N_leg*Av1 / Av
= 0.62800
-. Applied spacing s
= MIN[ smax, s1 ] =
0.143

m^2. )

m.
m.
m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
55
*.DESCRIPTION OF BEAM DATA (iSEC =
3) : ROOF BEAM
Section Type : Rectangle (RECT)
Beam Length (Span)
=
1.350 m.
Section Depth (Hc)
=
0.350 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
0.00 kN-m., LCB = 13
Negative Bending Moment N-Mu =
17.90 kN-m., LCB = 8
Shear Force
Vu =
27.88 kN. , LCB = 8
*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.292
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomin = 0.0000
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004)) =
-. Rhomax = k*Rho_et
=
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0069
-. Rhomin < Rho < Rhomax ---> O.K !

0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
44.65 kN-m.
40.18 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.000 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0040
0.0033
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0070
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
43.73 kN-m.
39.36 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.455 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute shear strength of concrete.
-. Vu
=
27.88 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
43.28 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
32.46 kN.
-. phiVc/2 < Vu < phiVc ---> Minimum shear reinforcement is require
d.
( ). Compute required shear reinforcement. ( Av1 =
-. Avmin1 = 50*bw/fys
=2.500e-004
-. Avmin2 = 0.75*SQRT(fc)*bw/fys =2.054e-004
-. Av
= MAX[ Avmin1, Avmin2 ] =2.500e-004
-. N_leg = 2
-. Calculate spacing s1 = N_leg*Av1 / Av
-. Applied spacing s
= MIN[ s1, d/2, 24 in

0.00008 m^2. )
m^2/m.
m^2/m.
m^2/m.
=
] =

0.628 m.
0.143 m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
58
*.DESCRIPTION OF BEAM DATA (iSEC =
3) : ROOF BEAM
Section Type : Rectangle (RECT)
Beam Length (Span)
=
3.050 m.
Section Depth (Hc)
=
0.350 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
5.50 kN-m., LCB =
Negative Bending Moment N-Mu =
15.61 kN-m., LCB =
Shear Force
Vu =
36.14 kN. , LCB =

4
8
8

*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.292
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0012
0.0012
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0069
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
44.65 kN-m.
40.18 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.137 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0070
-. Rhomin < Rho < Rhomax ---> O.K !

=
=
=
=
=

0.0033
0.0035
0.0033
0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
43.73 kN-m.
39.36 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.396 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================
( ). Compute shear strength of concrete.
-. Vu
=
36.14 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
43.28 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
32.46 kN.
-. Vu > phiVc ---> Shear reinforcement is required.
( ). Compute required shear reinforcement. ( Av1 = 0.00008
-. Vs = (Vu-phiVc)/phi =
4.90 kN.
-. 4*SQRT(fc)*bw*d =
86.56 kN.
-. 8*SQRT(fc)*bw*d =
173.11 kN.
-. Vs < 4*SQRT(fc)*bw*d ---> O.K !
-. Avmin1 = 50*bw/fys
= 0.00025 m^2/m.
-. Avmin2 = 0.75*SQRT(fc)*bw/fys = 0.00021 m^2/m.
-. Avmin = MAX[ Avmin1, Avmin2 ] = 0.00025 m^2/m.
-. Avreq = Vs/(fys*d) = 0.00006 m^2/m.
-. Av
= MAX[ Avmin, Avreq ] = 0.00025 m^2/m.
-. N_leg = 2
-. Maximum spacing smax = MIN[ d/2, 24 in ] =
0.143
-. Calculate spacing s1 = N_leg*Av1 / Av
= 0.62800
-. Applied spacing s
= MIN[ smax, s1 ] =
0.143

m^2. )

m.
m.
m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
59
*.DESCRIPTION OF BEAM DATA (iSEC =
3) : ROOF BEAM
Section Type : Rectangle (RECT)
Beam Length (Span)
=
3.150 m.
Section Depth (Hc)
=
0.350 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
5.56 kN-m., LCB =
Negative Bending Moment N-Mu =
17.10 kN-m., LCB =
Shear Force
Vu =
37.55 kN. , LCB =

8
4
5

*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.292
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0012
0.0012
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0069
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
44.65 kN-m.
40.18 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.138 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0070
-. Rhomin < Rho < Rhomax ---> O.K !

=
=
=
=
=

0.0033
0.0039
0.0033
0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
43.73 kN-m.
39.36 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.435 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================
( ). Compute shear strength of concrete.
-. Vu
=
37.55 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
43.28 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
32.46 kN.
-. Vu > phiVc ---> Shear reinforcement is required.
( ). Compute required shear reinforcement. ( Av1 = 0.00008
-. Vs = (Vu-phiVc)/phi =
6.79 kN.
-. 4*SQRT(fc)*bw*d =
86.56 kN.
-. 8*SQRT(fc)*bw*d =
173.11 kN.
-. Vs < 4*SQRT(fc)*bw*d ---> O.K !
-. Avmin1 = 50*bw/fys
= 0.00025 m^2/m.
-. Avmin2 = 0.75*SQRT(fc)*bw/fys = 0.00021 m^2/m.
-. Avmin = MAX[ Avmin1, Avmin2 ] = 0.00025 m^2/m.
-. Avreq = Vs/(fys*d) = 0.00009 m^2/m.
-. Av
= MAX[ Avmin, Avreq ] = 0.00025 m^2/m.
-. N_leg = 2
-. Maximum spacing smax = MIN[ d/2, 24 in ] =
0.143
-. Calculate spacing s1 = N_leg*Av1 / Av
= 0.62800
-. Applied spacing s
= MIN[ smax, s1 ] =
0.143

m^2. )

m.
m.
m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
60
*.DESCRIPTION OF BEAM DATA (iSEC =
3) : ROOF BEAM
Section Type : Rectangle (RECT)
Beam Length (Span)
=
2.763 m.
Section Depth (Hc)
=
0.350 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
4.36 kN-m., LCB =
Negative Bending Moment N-Mu =
13.16 kN-m., LCB =
Shear Force
Vu =
33.11 kN. , LCB =

9
5
5

*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.292
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0009
0.0009
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0069
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
44.65 kN-m.
40.18 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.108 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0070
-. Rhomin < Rho < Rhomax ---> O.K !

=
=
=
=
=

0.0033
0.0029
0.0029
0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
43.73 kN-m.
39.36 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.334 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================
( ). Compute shear strength of concrete.
-. Vu
=
33.11 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
43.28 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
32.46 kN.
-. Vu > phiVc ---> Shear reinforcement is required.
( ). Compute required shear reinforcement. ( Av1 = 0.00008
-. Vs = (Vu-phiVc)/phi =
0.88 kN.
-. 4*SQRT(fc)*bw*d =
86.56 kN.
-. 8*SQRT(fc)*bw*d =
173.11 kN.
-. Vs < 4*SQRT(fc)*bw*d ---> O.K !
-. Avmin1 = 50*bw/fys
= 0.00025 m^2/m.
-. Avmin2 = 0.75*SQRT(fc)*bw/fys = 0.00021 m^2/m.
-. Avmin = MAX[ Avmin1, Avmin2 ] = 0.00025 m^2/m.
-. Avreq = Vs/(fys*d) = 0.00001 m^2/m.
-. Av
= MAX[ Avmin, Avreq ] = 0.00025 m^2/m.
-. N_leg = 2
-. Maximum spacing smax = MIN[ d/2, 24 in ] =
0.143
-. Calculate spacing s1 = N_leg*Av1 / Av
= 0.62800
-. Applied spacing s
= MIN[ smax, s1 ] =
0.143

m^2. )

m.
m.
m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
62
*.DESCRIPTION OF BEAM DATA (iSEC =
3) : ROOF BEAM
Section Type : Rectangle (RECT)
Beam Length (Span)
=
2.050 m.
Section Depth (Hc)
=
0.350 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
27.08 kN-m., LCB = 4
Negative Bending Moment N-Mu =
0.00 kN-m., LCB = 13
Shear Force
Vu =
23.53 kN. , LCB = 4
*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.292
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0060
0.0033
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0069
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
44.65 kN-m.
40.18 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.674 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomin = 0.0000
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004)) =
-. Rhomax = k*Rho_et
=

0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0070
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
43.73 kN-m.
39.36 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.000 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute shear strength of concrete.
-. Vu
=
23.53 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
44.11 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
33.08 kN.
-. phiVc/2 < Vu < phiVc ---> Minimum shear reinforcement is require
d.
( ). Compute required shear reinforcement. ( Av1 =
-. Avmin1 = 50*bw/fys
=2.500e-004
-. Avmin2 = 0.75*SQRT(fc)*bw/fys =2.054e-004
-. Av
= MAX[ Avmin1, Avmin2 ] =2.500e-004
-. N_leg = 2
-. Calculate spacing s1 = N_leg*Av1 / Av
-. Applied spacing s
= MIN[ s1, d/2, 24 in

0.00008 m^2. )
m^2/m.
m^2/m.
m^2/m.
=
] =

0.628 m.
0.146 m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
63
*.DESCRIPTION OF BEAM DATA (iSEC =
3) : ROOF BEAM
Section Type : Rectangle (RECT)
Beam Length (Span)
=
2.050 m.
Section Depth (Hc)
=
0.350 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
49.43 kN-m., LCB = 4
Negative Bending Moment N-Mu =
0.00 kN-m., LCB = 13
Shear Force
Vu =
42.14 kN. , LCB = 4
*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.278
2- 1-P16
0.00060
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0129
0.0033
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0108
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.071 m.
60.58 kN-m.
54.52 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.907 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomin = 0.0000
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004)) =
-. Rhomax = k*Rho_et
=

0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0070
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
43.73 kN-m.
39.36 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.000 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute shear strength of concrete.
-. Vu
=
42.14 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
42.02 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
31.52 kN.
-. Vu > phiVc ---> Shear reinforcement is required.
( ). Compute required shear reinforcement. ( Av1 = 0.00008
-. Vs = (Vu-phiVc)/phi =
14.16 kN.
-. 4*SQRT(fc)*bw*d =
84.05 kN.
-. 8*SQRT(fc)*bw*d =
168.10 kN.
-. Vs < 4*SQRT(fc)*bw*d ---> O.K !
-. Avmin1 = 50*bw/fys
= 0.00025 m^2/m.
-. Avmin2 = 0.75*SQRT(fc)*bw/fys = 0.00021 m^2/m.
-. Avmin = MAX[ Avmin1, Avmin2 ] = 0.00025 m^2/m.
-. Avreq = Vs/(fys*d) = 0.00018 m^2/m.
-. Av
= MAX[ Avmin, Avreq ] = 0.00025 m^2/m.
-. N_leg = 2
-. Maximum spacing smax = MIN[ d/2, 24 in ] =
0.139
-. Calculate spacing s1 = N_leg*Av1 / Av
= 0.62800
-. Applied spacing s
= MIN[ smax, s1 ] =
0.139

m^2. )

m.
m.
m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
64
*.DESCRIPTION OF BEAM DATA (iSEC =
3) : ROOF BEAM
Section Type : Rectangle (RECT)
Beam Length (Span)
=
2.050 m.
Section Depth (Hc)
=
0.350 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
46.79 kN-m., LCB = 4
Negative Bending Moment N-Mu =
0.00 kN-m., LCB = 13
Shear Force
Vu =
39.98 kN. , LCB = 4
*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.278
2- 1-P16
0.00060
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0121
0.0033
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0108
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.071 m.
60.58 kN-m.
54.52 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.858 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomin = 0.0000
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004)) =
-. Rhomax = k*Rho_et
=

0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0070
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
43.73 kN-m.
39.36 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.000 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute shear strength of concrete.
-. Vu
=
39.98 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
42.02 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
31.52 kN.
-. Vu > phiVc ---> Shear reinforcement is required.
( ). Compute required shear reinforcement. ( Av1 = 0.00008
-. Vs = (Vu-phiVc)/phi =
11.29 kN.
-. 4*SQRT(fc)*bw*d =
84.05 kN.
-. 8*SQRT(fc)*bw*d =
168.10 kN.
-. Vs < 4*SQRT(fc)*bw*d ---> O.K !
-. Avmin1 = 50*bw/fys
= 0.00025 m^2/m.
-. Avmin2 = 0.75*SQRT(fc)*bw/fys = 0.00021 m^2/m.
-. Avmin = MAX[ Avmin1, Avmin2 ] = 0.00025 m^2/m.
-. Avreq = Vs/(fys*d) = 0.00015 m^2/m.
-. Av
= MAX[ Avmin, Avreq ] = 0.00025 m^2/m.
-. N_leg = 2
-. Maximum spacing smax = MIN[ d/2, 24 in ] =
0.139
-. Calculate spacing s1 = N_leg*Av1 / Av
= 0.62800
-. Applied spacing s
= MIN[ smax, s1 ] =
0.139

m^2. )

m.
m.
m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
67
*.DESCRIPTION OF BEAM DATA (iSEC =
1) : BEAM2
Section Type : Rectangle (RECT)
Beam Length (Span)
=
0.950 m.
Section Depth (Hc)
=
0.300 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
0.00 kN-m., LCB = 13
Negative Bending Moment N-Mu =
19.40 kN-m., LCB = 2
Shear Force
Vu =
37.69 kN. , LCB = 2
*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.242
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomin = 0.0000
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004)) =
-. Rhomax = k*Rho_et
=
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0083
-. Rhomin < Rho < Rhomax ---> O.K !

0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
36.33 kN-m.
32.70 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.000 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0066
0.0033
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0085
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
35.41 kN-m.
31.87 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.609 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute shear strength of concrete.
-. Vu
=
37.69 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
35.72 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
26.79 kN.
-. Vu > phiVc ---> Shear reinforcement is required.
( ). Compute required shear reinforcement. ( Av1 = 0.00008
-. Vs = (Vu-phiVc)/phi =
14.52 kN.
-. 4*SQRT(fc)*bw*d =
71.45 kN.
-. 8*SQRT(fc)*bw*d =
142.90 kN.
-. Vs < 4*SQRT(fc)*bw*d ---> O.K !
-. Avmin1 = 50*bw/fys
= 0.00025 m^2/m.
-. Avmin2 = 0.75*SQRT(fc)*bw/fys = 0.00021 m^2/m.
-. Avmin = MAX[ Avmin1, Avmin2 ] = 0.00025 m^2/m.
-. Avreq = Vs/(fys*d) = 0.00022 m^2/m.
-. Av
= MAX[ Avmin, Avreq ] = 0.00025 m^2/m.
-. N_leg = 2
-. Maximum spacing smax = MIN[ d/2, 24 in ] =
0.118
-. Calculate spacing s1 = N_leg*Av1 / Av
= 0.62800
-. Applied spacing s
= MIN[ smax, s1 ] =
0.118

m^2. )

m.
m.
m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
68
*.DESCRIPTION OF BEAM DATA (iSEC =
1) : BEAM2
Section Type : Rectangle (RECT)
Beam Length (Span)
=
4.100 m.
Section Depth (Hc)
=
0.300 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
6.84 kN-m., LCB =
Negative Bending Moment N-Mu =
14.48 kN-m., LCB =
Shear Force
Vu =
24.83 kN. , LCB =

4
8
6

*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.242
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0021
0.0021
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0083
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
36.33 kN-m.
32.70 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.209 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0085
-. Rhomin < Rho < Rhomax ---> O.K !

=
=
=
=
=

0.0033
0.0048
0.0033
0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
35.41 kN-m.
31.87 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.454 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================
( ). Compute shear strength of concrete.
-. Vu
=
24.83 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
35.72 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
26.79 kN.
-. phiVc/2 < Vu < phiVc ---> Minimum shear reinforcement is require
d.
( ). Compute required shear reinforcement. ( Av1 =
-. Avmin1 = 50*bw/fys
=2.500e-004
-. Avmin2 = 0.75*SQRT(fc)*bw/fys =2.054e-004
-. Av
= MAX[ Avmin1, Avmin2 ] =2.500e-004
-. N_leg = 2
-. Calculate spacing s1 = N_leg*Av1 / Av
-. Applied spacing s
= MIN[ s1, d/2, 24 in

0.00008 m^2. )
m^2/m.
m^2/m.
m^2/m.
=
] =

0.628 m.
0.118 m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
69
*.DESCRIPTION OF BEAM DATA (iSEC =
2) : BEAM1
Section Type : Rectangle (RECT)
Beam Length (Span)
=
2.763 m.
Section Depth (Hc)
=
0.400 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
3.78 kN-m., LCB =
Negative Bending Moment N-Mu =
14.75 kN-m., LCB =
Shear Force
Vu =
29.33 kN. , LCB =

9
5
3

*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.342
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0006
0.0006
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0059
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
52.97 kN-m.
47.67 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.079 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0060
-. Rhomin < Rho < Rhomax ---> O.K !

=
=
=
=
=

0.0033
0.0024
0.0024
0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
52.05 kN-m.
46.85 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.315 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================
( ). Compute shear strength of concrete.
-. Vu
=
29.33 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
50.83 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
38.12 kN.
-. phiVc/2 < Vu < phiVc ---> Minimum shear reinforcement is require
d.
( ). Compute required shear reinforcement. ( Av1 =
-. Avmin1 = 50*bw/fys
=2.500e-004
-. Avmin2 = 0.75*SQRT(fc)*bw/fys =2.054e-004
-. Av
= MAX[ Avmin1, Avmin2 ] =2.500e-004
-. N_leg = 2
-. Calculate spacing s1 = N_leg*Av1 / Av
-. Applied spacing s
= MIN[ s1, d/2, 24 in

0.00008 m^2. )
m^2/m.
m^2/m.
m^2/m.
=
] =

0.628 m.
0.168 m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
70
*.DESCRIPTION OF BEAM DATA (iSEC =
1) : BEAM2
Section Type : Rectangle (RECT)
Beam Length (Span)
=
1.113 m.
Section Depth (Hc)
=
0.300 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
5.48 kN-m., LCB = 9
Negative Bending Moment N-Mu =
0.00 kN-m., LCB = 13
Shear Force
Vu =
13.90 kN. , LCB = 9
*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.242
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0017
0.0017
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0083
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
36.33 kN-m.
32.70 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.168 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomin = 0.0000
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004)) =
-. Rhomax = k*Rho_et
=

0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0085
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
35.41 kN-m.
31.87 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.000 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute shear strength of concrete.
-. Vu
=
13.90 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
36.56 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
27.42 kN.
-. phiVc/2 < Vu < phiVc ---> Minimum shear reinforcement is require
d.
( ). Compute required shear reinforcement. ( Av1 =
-. Avmin1 = 50*bw/fys
=2.500e-004
-. Avmin2 = 0.75*SQRT(fc)*bw/fys =2.054e-004
-. Av
= MAX[ Avmin1, Avmin2 ] =2.500e-004
-. N_leg = 2
-. Calculate spacing s1 = N_leg*Av1 / Av
-. Applied spacing s
= MIN[ s1, d/2, 24 in

0.00008 m^2. )
m^2/m.
m^2/m.
m^2/m.
=
] =

0.628 m.
0.121 m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
71
*.DESCRIPTION OF BEAM DATA (iSEC =
1) : BEAM2
Section Type : Rectangle (RECT)
Beam Length (Span)
=
0.950 m.
Section Depth (Hc)
=
0.300 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
0.00 kN-m., LCB = 13
Negative Bending Moment N-Mu =
19.20 kN-m., LCB = 6
Shear Force
Vu =
37.34 kN. , LCB = 6
*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.242
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomin = 0.0000
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004)) =
-. Rhomax = k*Rho_et
=
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0083
-. Rhomin < Rho < Rhomax ---> O.K !

0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
36.33 kN-m.
32.70 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.000 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0065
0.0033
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0085
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
35.41 kN-m.
31.87 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.602 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute shear strength of concrete.
-. Vu
=
37.34 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
35.72 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
26.79 kN.
-. Vu > phiVc ---> Shear reinforcement is required.
( ). Compute required shear reinforcement. ( Av1 = 0.00008
-. Vs = (Vu-phiVc)/phi =
14.06 kN.
-. 4*SQRT(fc)*bw*d =
71.45 kN.
-. 8*SQRT(fc)*bw*d =
142.90 kN.
-. Vs < 4*SQRT(fc)*bw*d ---> O.K !
-. Avmin1 = 50*bw/fys
= 0.00025 m^2/m.
-. Avmin2 = 0.75*SQRT(fc)*bw/fys = 0.00021 m^2/m.
-. Avmin = MAX[ Avmin1, Avmin2 ] = 0.00025 m^2/m.
-. Avreq = Vs/(fys*d) = 0.00022 m^2/m.
-. Av
= MAX[ Avmin, Avreq ] = 0.00025 m^2/m.
-. N_leg = 2
-. Maximum spacing smax = MIN[ d/2, 24 in ] =
0.118
-. Calculate spacing s1 = N_leg*Av1 / Av
= 0.62800
-. Applied spacing s
= MIN[ smax, s1 ] =
0.118

m^2. )

m.
m.
m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
78
*.DESCRIPTION OF BEAM DATA (iSEC =
3) : ROOF BEAM
Section Type : Rectangle (RECT)
Beam Length (Span)
=
2.050 m.
Section Depth (Hc)
=
0.350 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
0.00 kN-m., LCB = 13
Negative Bending Moment N-Mu =
20.65 kN-m., LCB = 8
Shear Force
Vu =
24.04 kN. , LCB = 8
*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.292
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomin = 0.0000
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004)) =
-. Rhomax = k*Rho_et
=
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0069
-. Rhomin < Rho < Rhomax ---> O.K !

0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
44.65 kN-m.
40.18 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.000 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0047
0.0033
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0070
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
43.73 kN-m.
39.36 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.525 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute shear strength of concrete.
-. Vu
=
24.04 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
43.28 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
32.46 kN.
-. phiVc/2 < Vu < phiVc ---> Minimum shear reinforcement is require
d.
( ). Compute required shear reinforcement. ( Av1 =
-. Avmin1 = 50*bw/fys
=2.500e-004
-. Avmin2 = 0.75*SQRT(fc)*bw/fys =2.054e-004
-. Av
= MAX[ Avmin1, Avmin2 ] =2.500e-004
-. N_leg = 2
-. Calculate spacing s1 = N_leg*Av1 / Av
-. Applied spacing s
= MIN[ s1, d/2, 24 in

0.00008 m^2. )
m^2/m.
m^2/m.
m^2/m.
=
] =

0.628 m.
0.143 m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
79
*.DESCRIPTION OF BEAM DATA (iSEC =
3) : ROOF BEAM
Section Type : Rectangle (RECT)
Beam Length (Span)
=
2.050 m.
Section Depth (Hc)
=
0.350 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
23.99 kN-m., LCB = 4
Negative Bending Moment N-Mu =
0.00 kN-m., LCB = 13
Shear Force
Vu =
21.03 kN. , LCB = 4
*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.292
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0053
0.0033
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0069
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
44.65 kN-m.
40.18 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.597 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomin = 0.0000
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004)) =
-. Rhomax = k*Rho_et
=

0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0070
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
43.73 kN-m.
39.36 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.000 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute shear strength of concrete.
-. Vu
=
21.03 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
44.11 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
33.08 kN.
-. phiVc/2 < Vu < phiVc ---> Minimum shear reinforcement is require
d.
( ). Compute required shear reinforcement. ( Av1 =
-. Avmin1 = 50*bw/fys
=2.500e-004
-. Avmin2 = 0.75*SQRT(fc)*bw/fys =2.054e-004
-. Av
= MAX[ Avmin1, Avmin2 ] =2.500e-004
-. N_leg = 2
-. Calculate spacing s1 = N_leg*Av1 / Av
-. Applied spacing s
= MIN[ s1, d/2, 24 in

0.00008 m^2. )
m^2/m.
m^2/m.
m^2/m.
=
] =

0.628 m.
0.146 m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
82
*.DESCRIPTION OF BEAM DATA (iSEC =
3) : ROOF BEAM
Section Type : Rectangle (RECT)
Beam Length (Span)
=
1.625 m.
Section Depth (Hc)
=
0.350 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
0.28 kN-m., LCB =
Negative Bending Moment N-Mu =
1.33 kN-m., LCB =
Shear Force
Vu =
2.63 kN. , LCB =

8
4
4

*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.292
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

= 0.0033
=5.8672e-005
=5.8672e-005
= 0.0155
= 0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0069
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
44.65 kN-m.
40.18 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.007 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0070
-. Rhomin < Rho < Rhomax ---> O.K !

=
=
=
=
=

0.0033
0.0003
0.0003
0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
43.73 kN-m.
39.36 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.034 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================
( ). Compute shear strength of concrete.
-. Vu
=
2.63 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
43.28 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
32.46 kN.
-. Vu < phiVc/2 ---> Shear reinforcement is not required.
( ). Compute required shear reinforcement.
-. Applied spacing s
= MIN[ d/2, 24 in ] =

0.143 m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
84
*.DESCRIPTION OF BEAM DATA (iSEC =
3) : ROOF BEAM
Section Type : Rectangle (RECT)
Beam Length (Span)
=
0.700 m.
Section Depth (Hc)
=
0.350 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
4.61 kN-m., LCB =
Negative Bending Moment N-Mu =
1.88 kN-m., LCB =
Shear Force
Vu =
23.85 kN. , LCB =

4
8
8

*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.292
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0010
0.0010
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0069
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
44.65 kN-m.
40.18 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.115 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0070
-. Rhomin < Rho < Rhomax ---> O.K !

=
=
=
=
=

0.0033
0.0004
0.0004
0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
43.73 kN-m.
39.36 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.048 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================
( ). Compute shear strength of concrete.
-. Vu
=
23.85 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
44.11 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
33.08 kN.
-. phiVc/2 < Vu < phiVc ---> Minimum shear reinforcement is require
d.
( ). Compute required shear reinforcement. ( Av1 =
-. Avmin1 = 50*bw/fys
=2.500e-004
-. Avmin2 = 0.75*SQRT(fc)*bw/fys =2.054e-004
-. Av
= MAX[ Avmin1, Avmin2 ] =2.500e-004
-. N_leg = 2
-. Calculate spacing s1 = N_leg*Av1 / Av
-. Applied spacing s
= MIN[ s1, d/2, 24 in

0.00008 m^2. )
m^2/m.
m^2/m.
m^2/m.
=
] =

0.628 m.
0.146 m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB =
98
*.DESCRIPTION OF BEAM DATA (iSEC =
5) : BEAM3
Section Type : Rectangle (RECT)
Beam Length (Span)
=
1.150 m.
Section Depth (Hc)
=
0.300 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
0.54 kN-m., LCB =
Negative Bending Moment N-Mu =
5.62 kN-m., LCB =
Shear Force
Vu =
12.56 kN. , LCB =

5
9
9

*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.242
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0002
0.0002
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0083
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
36.33 kN-m.
32.70 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.016 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0085
-. Rhomin < Rho < Rhomax ---> O.K !

=
=
=
=
=

0.0033
0.0018
0.0018
0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
35.41 kN-m.
31.87 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.176 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================
( ). Compute shear strength of concrete.
-. Vu
=
12.56 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
35.72 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
26.79 kN.
-. Vu < phiVc/2 ---> Shear reinforcement is not required.
( ). Compute required shear reinforcement.
-. Applied spacing s
= MIN[ d/2, 24 in ] =

0.118 m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB = 101
*.DESCRIPTION OF BEAM DATA (iSEC =
3) : ROOF BEAM
Section Type : Rectangle (RECT)
Beam Length (Span)
=
1.625 m.
Section Depth (Hc)
=
0.350 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
0.00 kN-m., LCB = 13
Negative Bending Moment N-Mu =
9.30 kN-m., LCB = 9
Shear Force
Vu =
23.71 kN. , LCB = 9
*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.292
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomin = 0.0000
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004)) =
-. Rhomax = k*Rho_et
=
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0069
-. Rhomin < Rho < Rhomax ---> O.K !

0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
44.65 kN-m.
40.18 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.000 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0021
0.0021
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0070
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
43.73 kN-m.
39.36 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.236 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute shear strength of concrete.
-. Vu
=
23.71 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
43.28 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
32.46 kN.
-. phiVc/2 < Vu < phiVc ---> Minimum shear reinforcement is require
d.
( ). Compute required shear reinforcement. ( Av1 =
-. Avmin1 = 50*bw/fys
=2.500e-004
-. Avmin2 = 0.75*SQRT(fc)*bw/fys =2.054e-004
-. Av
= MAX[ Avmin1, Avmin2 ] =2.500e-004
-. N_leg = 2
-. Calculate spacing s1 = N_leg*Av1 / Av
-. Applied spacing s
= MIN[ s1, d/2, 24 in

0.00008 m^2. )
m^2/m.
m^2/m.
m^2/m.
=
] =

0.628 m.
0.143 m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB = 102
*.DESCRIPTION OF BEAM DATA (iSEC =
3) : ROOF BEAM
Section Type : Rectangle (RECT)
Beam Length (Span)
=
1.350 m.
Section Depth (Hc)
=
0.350 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
0.53 kN-m., LCB =
Negative Bending Moment N-Mu =
6.64 kN-m., LCB =
Shear Force
Vu =
9.64 kN. , LCB =

4
8
8

*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.292
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0001
0.0001
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0069
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
44.65 kN-m.
40.18 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.013 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0070
-. Rhomin < Rho < Rhomax ---> O.K !

=
=
=
=
=

0.0033
0.0015
0.0015
0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
43.73 kN-m.
39.36 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.169 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================
( ). Compute shear strength of concrete.
-. Vu
=
9.64 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
43.28 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
32.46 kN.
-. Vu < phiVc/2 ---> Shear reinforcement is not required.
( ). Compute required shear reinforcement.
-. Applied spacing s
= MIN[ d/2, 24 in ] =

0.143 m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB = 103
*.DESCRIPTION OF BEAM DATA (iSEC =
5) : BEAM3
Section Type : Rectangle (RECT)
Beam Length (Span)
=
1.350 m.
Section Depth (Hc)
=
0.300 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
16.24 kN-m., LCB =
Negative Bending Moment N-Mu =
9.21 kN-m., LCB =
Shear Force
Vu =
26.37 kN. , LCB =

4
8
4

*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.242
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0052
0.0033
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0083
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
36.33 kN-m.
32.70 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.497 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0085
-. Rhomin < Rho < Rhomax ---> O.K !

=
=
=
=
=

0.0033
0.0030
0.0030
0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
35.41 kN-m.
31.87 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.289 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================
( ). Compute shear strength of concrete.
-. Vu
=
26.37 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
36.56 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
27.42 kN.
-. phiVc/2 < Vu < phiVc ---> Minimum shear reinforcement is require
d.
( ). Compute required shear reinforcement. ( Av1 =
-. Avmin1 = 50*bw/fys
=2.500e-004
-. Avmin2 = 0.75*SQRT(fc)*bw/fys =2.054e-004
-. Av
= MAX[ Avmin1, Avmin2 ] =2.500e-004
-. N_leg = 2
-. Calculate spacing s1 = N_leg*Av1 / Av
-. Applied spacing s
= MIN[ s1, d/2, 24 in

0.00008 m^2. )
m^2/m.
m^2/m.
m^2/m.
=
] =

0.628 m.
0.121 m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB = 107
*.DESCRIPTION OF BEAM DATA (iSEC =
3) : ROOF BEAM
Section Type : Rectangle (RECT)
Beam Length (Span)
=
1.150 m.
Section Depth (Hc)
=
0.350 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
2.20 kN-m., LCB =
Negative Bending Moment N-Mu =
1.42 kN-m., LCB =
Shear Force
Vu =
5.62 kN. , LCB =

4
8
4

*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.292
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0005
0.0005
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0069
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
44.65 kN-m.
40.18 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.055 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0070
-. Rhomin < Rho < Rhomax ---> O.K !

=
=
=
=
=

0.0033
0.0003
0.0003
0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
43.73 kN-m.
39.36 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.036 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================
( ). Compute shear strength of concrete.
-. Vu
=
5.62 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
44.11 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
33.08 kN.
-. Vu < phiVc/2 ---> Shear reinforcement is not required.
( ). Compute required shear reinforcement.
-. Applied spacing s
= MIN[ d/2, 24 in ] =

0.146 m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB = 108
*.DESCRIPTION OF BEAM DATA (iSEC =
3) : ROOF BEAM
Section Type : Rectangle (RECT)
Beam Length (Span)
=
2.750 m.
Section Depth (Hc)
=
0.350 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
1.99 kN-m., LCB =
Negative Bending Moment N-Mu =
10.32 kN-m., LCB =
Shear Force
Vu =
10.36 kN. , LCB =

8
4
4

*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.292
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0004
0.0004
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0069
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
44.65 kN-m.
40.18 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.050 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0070
-. Rhomin < Rho < Rhomax ---> O.K !

=
=
=
=
=

0.0033
0.0023
0.0023
0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
43.73 kN-m.
39.36 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.262 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================
( ). Compute shear strength of concrete.
-. Vu
=
10.36 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
43.28 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
32.46 kN.
-. Vu < phiVc/2 ---> Shear reinforcement is not required.
( ). Compute required shear reinforcement.
-. Applied spacing s
= MIN[ d/2, 24 in ] =

0.143 m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB = 109
*.DESCRIPTION OF BEAM DATA (iSEC =
2) : BEAM1
Section Type : Rectangle (RECT)
Beam Length (Span)
=
0.350 m.
Section Depth (Hc)
=
0.400 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
25.26 kN-m., LCB = 4
Negative Bending Moment N-Mu =
0.00 kN-m., LCB = 13
Shear Force
Vu =
52.03 kN. , LCB = 8
*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.342
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0040
0.0033
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0059
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
52.97 kN-m.
47.67 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.530 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomin = 0.0000
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004)) =
-. Rhomax = k*Rho_et
=

0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0060
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
52.05 kN-m.
46.85 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.000 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute shear strength of concrete.
-. Vu
=
52.03 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
51.66 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
38.75 kN.
-. Vu > phiVc ---> Shear reinforcement is required.
( ). Compute required shear reinforcement. ( Av1 = 0.00008
-. Vs = (Vu-phiVc)/phi =
17.72 kN.
-. 4*SQRT(fc)*bw*d =
103.32 kN.
-. 8*SQRT(fc)*bw*d =
206.65 kN.
-. Vs < 4*SQRT(fc)*bw*d ---> O.K !
-. Avmin1 = 50*bw/fys
= 0.00025 m^2/m.
-. Avmin2 = 0.75*SQRT(fc)*bw/fys = 0.00021 m^2/m.
-. Avmin = MAX[ Avmin1, Avmin2 ] = 0.00025 m^2/m.
-. Avreq = Vs/(fys*d) = 0.00019 m^2/m.
-. Av
= MAX[ Avmin, Avreq ] = 0.00025 m^2/m.
-. N_leg = 2
-. Maximum spacing smax = MIN[ d/2, 24 in ] =
0.171
-. Calculate spacing s1 = N_leg*Av1 / Av
= 0.62800
-. Applied spacing s
= MIN[ smax, s1 ] =
0.171

m^2. )

m.
m.
m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB = 110
*.DESCRIPTION OF BEAM DATA (iSEC =
2) : BEAM1
Section Type : Rectangle (RECT)
Beam Length (Span)
=
2.750 m.
Section Depth (Hc)
=
0.400 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
45.45 kN-m., LCB = 4
Negative Bending Moment N-Mu =
0.00 kN-m., LCB = 13
Shear Force
Vu =
23.10 kN. , LCB = 8
*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.342
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0074
0.0033
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0059
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
52.97 kN-m.
47.67 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.953 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomin = 0.0000
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004)) =
-. Rhomax = k*Rho_et
=

0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0060
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
52.05 kN-m.
46.85 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.000 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute shear strength of concrete.
-. Vu
=
23.10 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
51.66 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
38.75 kN.
-. phiVc/2 < Vu < phiVc ---> Minimum shear reinforcement is require
d.
( ). Compute required shear reinforcement. ( Av1 =
-. Avmin1 = 50*bw/fys
=2.500e-004
-. Avmin2 = 0.75*SQRT(fc)*bw/fys =2.054e-004
-. Av
= MAX[ Avmin1, Avmin2 ] =2.500e-004
-. N_leg = 2
-. Calculate spacing s1 = N_leg*Av1 / Av
-. Applied spacing s
= MIN[ s1, d/2, 24 in

0.00008 m^2. )
m^2/m.
m^2/m.
m^2/m.
=
] =

0.628 m.
0.171 m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB = 111
*.DESCRIPTION OF BEAM DATA (iSEC =
5) : BEAM3
Section Type : Rectangle (RECT)
Beam Length (Span)
=
2.775 m.
Section Depth (Hc)
=
0.300 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
2.15 kN-m., LCB =
Negative Bending Moment N-Mu =
18.77 kN-m., LCB =
Shear Force
Vu =
34.08 kN. , LCB =

5
9
7

*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.242
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0007
0.0007
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0083
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
36.33 kN-m.
32.70 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.066 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0085
-. Rhomin < Rho < Rhomax ---> O.K !

=
=
=
=
=

0.0033
0.0064
0.0033
0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
35.41 kN-m.
31.87 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.589 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================
( ). Compute shear strength of concrete.
-. Vu
=
34.08 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
35.72 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
26.79 kN.
-. Vu > phiVc ---> Shear reinforcement is required.
( ). Compute required shear reinforcement. ( Av1 = 0.00008
-. Vs = (Vu-phiVc)/phi =
9.72 kN.
-. 4*SQRT(fc)*bw*d =
71.45 kN.
-. 8*SQRT(fc)*bw*d =
142.90 kN.
-. Vs < 4*SQRT(fc)*bw*d ---> O.K !
-. Avmin1 = 50*bw/fys
= 0.00025 m^2/m.
-. Avmin2 = 0.75*SQRT(fc)*bw/fys = 0.00021 m^2/m.
-. Avmin = MAX[ Avmin1, Avmin2 ] = 0.00025 m^2/m.
-. Avreq = Vs/(fys*d) = 0.00015 m^2/m.
-. Av
= MAX[ Avmin, Avreq ] = 0.00025 m^2/m.
-. N_leg = 2
-. Maximum spacing smax = MIN[ d/2, 24 in ] =
0.118
-. Calculate spacing s1 = N_leg*Av1 / Av
= 0.62800
-. Applied spacing s
= MIN[ smax, s1 ] =
0.118

m^2. )

m.
m.
m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB = 112
*.DESCRIPTION OF BEAM DATA (iSEC =
5) : BEAM3
Section Type : Rectangle (RECT)
Beam Length (Span)
=
2.750 m.
Section Depth (Hc)
=
0.300 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
9.84 kN-m., LCB =
Negative Bending Moment N-Mu =
23.65 kN-m., LCB =
Shear Force
Vu =
37.16 kN. , LCB =

8
4
4

*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.242
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0031
0.0031
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0083
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
36.33 kN-m.
32.70 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.301 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0085
-. Rhomin < Rho < Rhomax ---> O.K !

=
=
=
=
=

0.0033
0.0082
0.0033
0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
35.41 kN-m.
31.87 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.742 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================
( ). Compute shear strength of concrete.
-. Vu
=
37.16 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
35.72 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
26.79 kN.
-. Vu > phiVc ---> Shear reinforcement is required.
( ). Compute required shear reinforcement. ( Av1 = 0.00008
-. Vs = (Vu-phiVc)/phi =
13.83 kN.
-. 4*SQRT(fc)*bw*d =
71.45 kN.
-. 8*SQRT(fc)*bw*d =
142.90 kN.
-. Vs < 4*SQRT(fc)*bw*d ---> O.K !
-. Avmin1 = 50*bw/fys
= 0.00025 m^2/m.
-. Avmin2 = 0.75*SQRT(fc)*bw/fys = 0.00021 m^2/m.
-. Avmin = MAX[ Avmin1, Avmin2 ] = 0.00025 m^2/m.
-. Avreq = Vs/(fys*d) = 0.00021 m^2/m.
-. Av
= MAX[ Avmin, Avreq ] = 0.00025 m^2/m.
-. N_leg = 2
-. Maximum spacing smax = MIN[ d/2, 24 in ] =
0.118
-. Calculate spacing s1 = N_leg*Av1 / Av
= 0.62800
-. Applied spacing s
= MIN[ smax, s1 ] =
0.118

m^2. )

m.
m.
m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB = 113
*.DESCRIPTION OF BEAM DATA (iSEC =
5) : BEAM3
Section Type : Rectangle (RECT)
Beam Length (Span)
=
1.150 m.
Section Depth (Hc)
=
0.300 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
0.00 kN-m., LCB = 13
Negative Bending Moment N-Mu =
25.11 kN-m., LCB = 4
Shear Force
Vu =
48.42 kN. , LCB = 2
*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.242
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomin = 0.0000
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004)) =
-. Rhomax = k*Rho_et
=
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0083
-. Rhomin < Rho < Rhomax ---> O.K !

0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
36.33 kN-m.
32.70 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.000 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0087
0.0033
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0085
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
35.41 kN-m.
31.87 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.788 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute shear strength of concrete.
-. Vu
=
48.42 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
35.72 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
26.79 kN.
-. Vu > phiVc ---> Shear reinforcement is required.
( ). Compute required shear reinforcement. ( Av1 = 0.00008
-. Vs = (Vu-phiVc)/phi =
28.84 kN.
-. 4*SQRT(fc)*bw*d =
71.45 kN.
-. 8*SQRT(fc)*bw*d =
142.90 kN.
-. Vs < 4*SQRT(fc)*bw*d ---> O.K !
-. Avmin1 = 50*bw/fys
= 0.00025 m^2/m.
-. Avmin2 = 0.75*SQRT(fc)*bw/fys = 0.00021 m^2/m.
-. Avmin = MAX[ Avmin1, Avmin2 ] = 0.00025 m^2/m.
-. Avreq = Vs/(fys*d) = 0.00044 m^2/m.
-. Av
= MAX[ Avmin, Avreq ] = 0.00044 m^2/m.
-. N_leg = 2
-. Maximum spacing smax = MIN[ d/2, 24 in ] =
0.118
-. Calculate spacing s1 = N_leg*Av1 / Av
= 0.35506
-. Applied spacing s
= MIN[ smax, s1 ] =
0.118

m^2. )

m.
m.
m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB = 114
*.DESCRIPTION OF BEAM DATA (iSEC =
5) : BEAM3
Section Type : Rectangle (RECT)
Beam Length (Span)
=
1.625 m.
Section Depth (Hc)
=
0.300 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
11.82 kN-m., LCB = 4
Negative Bending Moment N-Mu =
0.00 kN-m., LCB = 13
Shear Force
Vu =
17.94 kN. , LCB = 6
*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.242
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0037
0.0033
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0083
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
36.33 kN-m.
32.70 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.362 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomin = 0.0000
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004)) =
-. Rhomax = k*Rho_et
=

0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0085
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
35.41 kN-m.
31.87 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.000 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute shear strength of concrete.
-. Vu
=
17.94 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
36.56 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
27.42 kN.
-. phiVc/2 < Vu < phiVc ---> Minimum shear reinforcement is require
d.
( ). Compute required shear reinforcement. ( Av1 =
-. Avmin1 = 50*bw/fys
=2.500e-004
-. Avmin2 = 0.75*SQRT(fc)*bw/fys =2.054e-004
-. Av
= MAX[ Avmin1, Avmin2 ] =2.500e-004
-. N_leg = 2
-. Calculate spacing s1 = N_leg*Av1 / Av
-. Applied spacing s
= MIN[ s1, d/2, 24 in

0.00008 m^2. )
m^2/m.
m^2/m.
m^2/m.
=
] =

0.628 m.
0.121 m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB = 115
*.DESCRIPTION OF BEAM DATA (iSEC =
2) : BEAM1
Section Type : Rectangle (RECT)
Beam Length (Span)
=
1.000 m.
Section Depth (Hc)
=
0.400 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
37.04 kN-m., LCB = 2
Negative Bending Moment N-Mu =
0.00 kN-m., LCB = 13
Shear Force
Vu =
68.24 kN. , LCB = 6
*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.342
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0060
0.0033
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0059
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
52.97 kN-m.
47.67 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.777 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomin = 0.0000
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004)) =
-. Rhomax = k*Rho_et
=

0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0060
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
52.05 kN-m.
46.85 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.000 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute shear strength of concrete.
-. Vu
=
68.24 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
51.66 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
38.75 kN.
-. Vu > phiVc ---> Shear reinforcement is required.
( ). Compute required shear reinforcement. ( Av1 = 0.00008
-. Vs = (Vu-phiVc)/phi =
39.33 kN.
-. 4*SQRT(fc)*bw*d =
103.32 kN.
-. 8*SQRT(fc)*bw*d =
206.65 kN.
-. Vs < 4*SQRT(fc)*bw*d ---> O.K !
-. Avmin1 = 50*bw/fys
= 0.00025 m^2/m.
-. Avmin2 = 0.75*SQRT(fc)*bw/fys = 0.00021 m^2/m.
-. Avmin = MAX[ Avmin1, Avmin2 ] = 0.00025 m^2/m.
-. Avreq = Vs/(fys*d) = 0.00042 m^2/m.
-. Av
= MAX[ Avmin, Avreq ] = 0.00042 m^2/m.
-. N_leg = 2
-. Maximum spacing smax = MIN[ d/2, 24 in ] =
0.171
-. Calculate spacing s1 = N_leg*Av1 / Av
= 0.37654
-. Applied spacing s
= MIN[ smax, s1 ] =
0.171

m^2. )

m.
m.
m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB = 116
*.DESCRIPTION OF BEAM DATA (iSEC =
5) : BEAM3
Section Type : Rectangle (RECT)
Beam Length (Span)
=
1.625 m.
Section Depth (Hc)
=
0.300 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
1.44 kN-m., LCB =
Negative Bending Moment N-Mu =
7.11 kN-m., LCB =
Shear Force
Vu =
18.85 kN. , LCB =

5
9
9

*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.242
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0004
0.0004
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0083
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
36.33 kN-m.
32.70 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.044 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0085
-. Rhomin < Rho < Rhomax ---> O.K !

=
=
=
=
=

0.0033
0.0023
0.0023
0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
35.41 kN-m.
31.87 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.223 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================
( ). Compute shear strength of concrete.
-. Vu
=
18.85 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
35.72 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
26.79 kN.
-. phiVc/2 < Vu < phiVc ---> Minimum shear reinforcement is require
d.
( ). Compute required shear reinforcement. ( Av1 =
-. Avmin1 = 50*bw/fys
=2.500e-004
-. Avmin2 = 0.75*SQRT(fc)*bw/fys =2.054e-004
-. Av
= MAX[ Avmin1, Avmin2 ] =2.500e-004
-. N_leg = 2
-. Calculate spacing s1 = N_leg*Av1 / Av
-. Applied spacing s
= MIN[ s1, d/2, 24 in

0.00008 m^2. )
m^2/m.
m^2/m.
m^2/m.
=
] =

0.628 m.
0.118 m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB = 117
*.DESCRIPTION OF BEAM DATA (iSEC =
5) : BEAM3
Section Type : Rectangle (RECT)
Beam Length (Span)
=
1.350 m.
Section Depth (Hc)
=
0.300 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
0.00 kN-m., LCB = 13
Negative Bending Moment N-Mu =
24.07 kN-m., LCB = 8
Shear Force
Vu =
34.78 kN. , LCB = 8
*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.242
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomin = 0.0000
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004)) =
-. Rhomax = k*Rho_et
=
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0083
-. Rhomin < Rho < Rhomax ---> O.K !

0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
36.33 kN-m.
32.70 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.000 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0083
0.0033
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0085
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
35.41 kN-m.
31.87 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.755 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute shear strength of concrete.
-. Vu
=
34.78 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
35.72 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
26.79 kN.
-. Vu > phiVc ---> Shear reinforcement is required.
( ). Compute required shear reinforcement. ( Av1 = 0.00008
-. Vs = (Vu-phiVc)/phi =
10.65 kN.
-. 4*SQRT(fc)*bw*d =
71.45 kN.
-. 8*SQRT(fc)*bw*d =
142.90 kN.
-. Vs < 4*SQRT(fc)*bw*d ---> O.K !
-. Avmin1 = 50*bw/fys
= 0.00025 m^2/m.
-. Avmin2 = 0.75*SQRT(fc)*bw/fys = 0.00021 m^2/m.
-. Avmin = MAX[ Avmin1, Avmin2 ] = 0.00025 m^2/m.
-. Avreq = Vs/(fys*d) = 0.00016 m^2/m.
-. Av
= MAX[ Avmin, Avreq ] = 0.00025 m^2/m.
-. N_leg = 2
-. Maximum spacing smax = MIN[ d/2, 24 in ] =
0.118
-. Calculate spacing s1 = N_leg*Av1 / Av
= 0.62800
-. Applied spacing s
= MIN[ smax, s1 ] =
0.118

m^2. )

m.
m.
m.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
*.midas Gen - RC-BEAM Analysis/Design Program.
*.PROJECT
:
*.DESIGN CODE : ACI318-08,
*.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in U.S. Customary
units in the report)
*.MEMBER
: Member Type = BEAM, MEMB = 121
*.DESCRIPTION OF BEAM DATA (iSEC =
5) : BEAM3
Section Type : Rectangle (RECT)
Beam Length (Span)
=
3.150 m.
Section Depth (Hc)
=
0.300 m.
Section Width (Bc)
=
0.200 m.
Concrete Strength (fc)
=
20684.278 KPa.
Modulus of Elasticity (Ec)
= 21525567.059 KPa.
Main Rebar Strength (fy)
=
413685.566 KPa.
Stirrups Strength (fys)
=
275790.378 KPa.
Modulus of Elasticity (Es)
= 199948023.746 KPa.
*.FORCES AND MOMENTS AT CHECK POINT <I> :
Positive Bending Moment P-Mu =
5.49 kN-m., LCB =
Negative Bending Moment N-Mu =
22.20 kN-m., LCB =
Shear Force
Vu =
43.71 kN. , LCB =

7
3
3

*.REINFORCEMENT PATTERN :
--------------------------------------------------------Location
i
di( m.)
Rebar
Asi( m^2.)
--------------------------------------------------------Top
1
0.064
2-P16
0.00040
Bottom
2
0.242
2-P16
0.00040
--------------------------------------------------------Stirrups : P10
===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.050 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.256 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.256 m.
-. s
=
0.084 m. < smax ---> O.K.

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et

=
=
=
=
=

0.0033
0.0017
0.0017
0.0155
0.0155

( ). Check ratio of tensile reinforcement.

-. Rho = As/(bw*d) = 0.0083
-. Rhomin < Rho < Rhomax ---> O.K !
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
36.33 kN-m.
32.70 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn =
0.168 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================
( ). Compute design parameter.
-. beta1 = 0.8500 ( fc < 4000 psi.)
( ). Check spacing of reinforcement closet to the tensile face.
-. fs = (2/3)*fy
=2.758e+005 KPa.
-. cc =
0.056 m.
-. s1 = 15*(40000/fs) - 2.5Cc =
0.242 m.
-. s2 = 12*(40000/fs)
=
0.305 m.
-. smax = MIN[ s1, s2 ]
=
0.242 m.
-. s
=
0.084 m. < smax ---> O.K.
( ). Compute required ratio of reinforcement.
-. k
= 1.000000
-. Rhomi1 = MAX[ 3*SQRT(fc)/fy, 200/fy ]
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ]
-. Rhomin = MIN[ Rhomi1, Rhomi2 ]
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004))
-. Rhomax = k*Rho_et
( ). Check ratio of tensile reinforcement.
-. Rho = As/(bw*d) = 0.0085
-. Rhomin < Rho < Rhomax ---> O.K !

=
=
=
=
=

0.0033
0.0076
0.0033
0.0155
0.0155

----------------------------------------------------------------------------------------midas Gen - RC-Beam Design

[ ACI318-08 ]
Gen
2016
================================================================================
==========
( ). Compute moment capacity.
-. a
= As*fy/(0.85*fc*bw) =
-. Mn
= As*fy*(d-a/2)
=
-. phi
= 0.90
-. phiMn = phi*Mn
=

0.047 m.
35.41 kN-m.
31.87 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn =
0.697 < 1.000 ---> O.K.
===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================
( ). Compute shear strength of concrete.
-. Vu
=
43.71 kN.
-. Vc
= 2*SQRT(fc)*bw*d =
35.72 kN.
-. phi
= 0.75
-. phiVc = phi*Vc
=
26.79 kN.
-. Vu > phiVc ---> Shear reinforcement is required.
( ). Compute required shear reinforcement. ( Av1 = 0.00008
-. Vs = (Vu-phiVc)/phi =
22.56 kN.
-. 4*SQRT(fc)*bw*d =
71.45 kN.
-. 8*SQRT(fc)*bw*d =
142.90 kN.
-. Vs < 4*SQRT(fc)*bw*d ---> O.K !
-. Avmin1 = 50*bw/fys
= 0.00025 m^2/m.
-. Avmin2 = 0.75*SQRT(fc)*bw/fys = 0.00021 m^2/m.
-. Avmin = MAX[ Avmin1, Avmin2 ] = 0.00025 m^2/m.
-. Avreq = Vs/(fys*d) = 0.00035 m^2/m.
-. Av
= MAX[ Avmin, Avreq ] = 0.00035 m^2/m.
-. N_leg = 2
-. Maximum spacing smax = MIN[ d/2, 24 in ] =
0.118
-. Calculate spacing s1 = N_leg*Av1 / Av
= 0.45390
-. Applied spacing s
= MIN[ smax, s1 ] =
0.118

m^2. )

m.
m.
m.