Scribd
Upload
56 views5 pages

I Answered As Follows:: The Accidental Admission or Escape of Liquid or Gas or Light Through A Hole or Crack

A business associate asked about procedures for conducting leak tests of pouches made of different materials and containing different products. The questioner was looking for baseline parameters like vacuum pressure, hold time, and any standards for different materials or pouch sizes. In response, the assistant explained that all packages will leak beyond a certain pressure or condition, and there are two main types of leak tests: vacuum and pressure tests. For vacuum leak testing, parameters like vacuum level and hold time can be adjusted based on the package material and distribution conditions, with higher quality packages requiring more stringent tests. The assistant provided examples of vacuum levels and hold times used in practice and referenced in standards.

Uploaded by

Kek Siang Ming
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
56 views5 pages

I Answered As Follows:: The Accidental Admission or Escape of Liquid or Gas or Light Through A Hole or Crack

A business associate asked about procedures for conducting leak tests of pouches made of different materials and containing different products. The questioner was looking for baseline parameters like vacuum pressure, hold time, and any standards for different materials or pouch sizes. In response, the assistant explained that all packages will leak beyond a certain pressure or condition, and there are two main types of leak tests: vacuum and pressure tests. For vacuum leak testing, parameters like vacuum level and hold time can be adjusted based on the package material and distribution conditions, with higher quality packages requiring more stringent tests. The assistant provided examples of vacuum levels and hold times used in practice and referenced in standards.

Uploaded by

Kek Siang Ming
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

A business associate recently posted on my forum on linkedin :

https://www.linkedin.com/groups/6966345

Hi,
Need to know the procedures for conducting the leak test of pouches
made of different laminates and of different products.
The baseline for setting the vacuum pressure, hold time, delay, release
time etc.
Is there any standards for different laminates or pouch sizes?
Thank you in advance for your kind support.

I answered as follows :
Hello Mr. Karthick.
Thank you for posting your query on this forum.
Hope my answer below is helpful to you and other readers. You all are
welcome to share your views. Maybe your views can help enhance my
limited knowledge on this vast subject of packaging.
Firstly lets define Leakage :
the accidental admission or escape of liquid or gas or light through a hole
or crack.
Or in simpler words relevant to our subject, an Undesirable Escape of
product from its container / packaging can be termed as leakage.
Surprising though it may sound, there is nothing in the world called as
Bullet-Proof or Water-Proof. A bullet-proof vest is actually a bulletresistant vest which is resistant only upto a certain calibre of projectile
fired from a certain distance. A Water-proof watch is actually a Water-

Resistant watch which is resistant only upto a certain depth or certain


exposure time.
Similarly, there is nothing like a Leak-Proof container. It is actually a leakresistant container which is resistant to leakage only upto a certain
pressure or condition. Beyond which it will start leaking.
So, any and every container / package will leak. The higher the
resistance, the better the container.
There are 2 general types of Leak Tests.
The Vacuum Leak Test which is the most common one and is used for
almost any kind of impervious package such as bottle or pouch or sachet,
etc.
The Pressure Leak Test which is useful only on Semi-Rigid packaging
such as bottles.

The Pressure Leak Test is done by closing the open end with a plug and
injecting air into it and holding it under pressure for a second or 2. If the
pressure drops, it signifies leakage. This test has its own flaws and is
highly dependent on the sealing plug quality and certain other factors.
Variants of this test enable online pre-fill leak detection of 100% samples
which is a positive point in its favour. Automatic rejection system can also
be added to the filling line to remove faulty containers before they reach
the filling station.
Other variants also allow you to test the Filled Containers by pressing the
side walls and measuring tightness. Not a fool-proof method but has its
own set of advantages.

Coming to our main topic of discussion on Vacuum Leakage Test.


Vacuum Leakage Test (VLT) is done by placing a package in a transparent
chamber like a Dessicator, applying Vacuum and holding it there for some
time.
VLT is primarly of 2 types. Wet Test and Dry Test.
If your product is solid or in powder form and the package has air inside
it, then its better to test it submerged in water. When vacuum is applied,
the pressure in the Tank reduces and drops below atmospheric pressure.
The air inside the package will start expanding till the pressure inside the
package is equal and opposite to the vacuum level. So if you have a 400
mmhg vacuum in the tank, the pressure inside the packaging with be +

400 mm hg. If there is any pinhole or leakage in the pouch / container,


you will see a stream of air bubble emanating from the package. We then
hold the vacuum at this level for some a few seconds. During this period,
weak seals and capillary defects (which were not immediate leakages, but
would have failed anyway in the market), will open up and show
airbubbles. The vacuum is then released and tank brought back to normal
atmospheric pressure. The packages are then removed and cut open to
inspect the content. Is it wet ? Sometimes packages may not show air
bubbles but you will find that the end of the test the water will have
penetrated into the package through the leak points.
If your product is in liquid for, then you can test it in dry condition also.
The product will pressurise during the vacuum phase and will ooze out
from the leak points, if any.
This test is very easy and versatile. Unfortunately it is unable to detect
micro-leakages from packages which contain high viscosity fluids. Eg.
Ketchup, Paste, etc., because the product itself blocks the pinhole and
prevents escape of air / product.
Another new concept coming up in the market is of Micro-Leak Detection
systems which uses a combination of Gas and Gas sensors to detect
leakages. We shall be introducing a product of this type in the first
quarter of 2016 to the Asian Market.

Coming back again to our main topic and your question of How
much Vacuum and How much Hold Time.
As I said in the beginning, there is nothing as a Leak Proof Packaging.
All packages will leak (or burst) at a certain pressure.
The higher your need for quality, the higher will be your Vacuum and
Time setting.
Company A is a local manufacturer of Tea in pouch. His distribution is in a
range of 300-400 Kms. His product gets sold in less than 1 month and his
brand is not a very famous one. He will suffice with 300 mmhg and 30
second test.
Company B is a Multi-National giant packing Tea in a pouch. His
distribution is in a range of 1000-2000 Kms or even export. His product
gets sold in about 3-6 months and his brand is a premium one. He cannot
allow a leaking package to spoil his brand image. He will need even 500
mmhg and 120-180 second test.
There is no one size fits all concept here.

The basic rule of thumb is that start at 300mmhg and check if market
complaints are getting reduced. If not, increase the vacuum and / or
time. Till the point you reach a scenario where your market complaints
are zero or negligible. Then use it as a benchmark for regular testing.
ASTM D 4991 specifies a method wherein the vacuum is gradually
increased to about 950mbar to detect the level of vacuum at which the
Rigid Containers (Bottles) start leaking.
ASTM D 5094 (Method B) specifies a Vibration Test followed by a vacuum
leak test at 250 mmhg for 10 mins.
ASTM D 3078 specifies Low, Medium and High Vacuum Test levels at
30 second for Flexible Packages. Low = 305-330mmhg, Medium = 457483mmhg, High = 609-635mmhg.
Another scenario is that you need to ensure that your package is worthy
of Air-Travel in non-pressurised Aircrafts or fit for use in high-altitude
locations. ASTM 6653 gives a table of various flying altitudes and vacuum
/ pressure levels at those heights. Eg. If you need to ensure that your
product is safe at an altitude of 20,000 ft above sea level, set the Vacuum
Leakage Test to be greater than 411mmhg.
More data on this is available on http://www.engineeringtoolbox.com/airaltitude-pressure-d_462.html
NoteSince we are using vacuum gage, you must subtract the desired
mmhg from 760 to achieve the vacuum mmhg. For example, 760 - 349 =
411 vacuum mmhg, equating into 20,000 ft.

Hope I was able to explain the method and values properly. And the
information was useful to you and others.

Best Regards,

Rohit Chawla.

Rohit Chawla
Test Techno Consultants

Phone : +91 - 265 - 2308600

K-1, 23/2, G.I.D.C. Ranoli

Mobile : +91 - 98240 69001

Vadodara - 391350

Email : [email protected]

Gujarat. INDIA.

Website : www.PackTest.com

You might also like