Scribd
Upload
72 views

5 Ce52 Design of RC Structures

This document contains 10 questions related to the design of reinforced concrete structures. Question 1 asks to derive an expression for percentage of tension and determine characteristic concrete strength from compression test results. Question 5 asks to determine reinforcement for a T-beam with given loading and geometry. Question 9 asks to design a rectangular footing for a given column load and soil bearing capacity.

Uploaded by

Danish Bhat
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
72 views

5 Ce52 Design of RC Structures

This document contains 10 questions related to the design of reinforced concrete structures. Question 1 asks to derive an expression for percentage of tension and determine characteristic concrete strength from compression test results. Question 5 asks to determine reinforcement for a T-beam with given loading and geometry. Question 9 asks to design a rectangular footing for a given column load and soil bearing capacity.

Uploaded by

Danish Bhat
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

SRI SIDDHARTHA INSTITUTE OF TECHNOLOGY, TUMKUR.

(An Autonomous Institution under Visvesvaraya Technological University, Belgaum.)

B.E., SEMESTER END EXAMINATIONS - AUGUST 2012


CE52 : DESIGN OF RC STRUCTURES
TIME: 3.00 Hrs

SEM:SUMMER

MAX MARKS: 100

NOTE: Missing data, if any may suitably be assumed. Use if IS 456-2000 and SP-16 is permitted.

1.a)

b)

Derive an expression for percentage of tension, for a given factored moment, material
properties and sectional properties.
Determine the characteristic strength of concrete which has given the following
compression test results on 150mm cubes.
40, 45, 38 41, 39, 51 48 38 N/mm2

c)

A rectangular section of effective size 230mm X


beam for a clear span of 6m. The thickness
maximum total uniformly distributed load can
reinforced with steel 4 bars of 20mm diameter
Use M25 concrete and Fe 415 steel.

500mm is used as a simply supported


of support is 230 mm. What is the
be allowed on the beam, the beam
is provided only on the tension side.

06

04

10

OR
2.a)

b)

3.a)
b)

Design a doubly reinforced beam is of 300mm x 600mm overall size, with an effective
cover of 50mm on both the compression and tension sides, factored moment 400 KNm. Use M20 concrete and Fe 415 steel. Sketch the details of reinforcements.
What is a doubly reinforced beam? Explain the circumstances of using doubly
reinforced beams.

Explain for any two types of shear failure in R.C beams with the help of neat sketches.
A simply supported beam 300mm wide and 600mm effective depth carries a uniformly
distributed load of 70 KN/m including its own weight over an effective span of 5 mts.
the reinforcement consists of 4 bars of 25mm diameter, out of these, two bars can be
safely bent up at one m distance from left support. Design the shear reinforcement for
the beam. Use M20 concrete and Fe 415 steel.

10

06

04

16

OR
4.a)

A simply supported slab 120mm thick a span 3.60m is reinforced with 10mm diameter
at 100 mm pitch at an effective cover of 20mm, if concrete grade is M20 and steel
grade Fe 415. Calculate the deflection due to creep for slabs, when it carries imposed
live load of 2 KN/m2 and floor finish 1KN/m2. Assum e 50% live load to be permanent
and creep co efficient = 1.6.

20

5.a)

A 6m effective span simply supported beam is supporting a slab of 100mm thickness


and ribs below the slab are 200mm wide and 300mm deep, the slab and beams are
cost as to act together, the beams are spaced at 4.5m centre to centre. Determine the
reinforcement for T-beam to carry an imposed load of 5 KN/m2 of the slab, floor finish
1.5 KN/m2. Use M20 concrete and Fe 415 steel. Sketch the detail^ of reinforcements.

20

OR
6.a)

Write a short note on the torsional reinforcement.

b) A cantilever beam projects 2.5m beyond the fixed end and carries a super imposed
load of 12KN per meter run. Design the cantilever using M20 concrete and Fe 415
steel. The width of support is 350mm and width of cantilever beam is 250mm. sketch
the details of reinforcement.

7.a)

b)

Design a Cantilever chejja slab projecting 1.50 m from support wall. Adopt a live load
2.0 KN/m2, use M20 concrete and Fe 415 grade of steel, floor finish 0.50 KN/m2 and
ceiling finish 0.375 KN/m2. Sketch the details of reinforcement.

16

iq

Explain the difference between one way slab and two way slab.
OR

8.a)

9.a)

Determine the reinforcement for a column of a braced frame for the following data.
Pu = 1800 KN. M ux = 150 KN-M, Muy = 110 KN-m, unsupported length of column = 4m.
Effective cover 50mm use M20 concrete and Fe 415 steel.

20

Design a rectangular footing for a rectangular column 230mm x 460mm to carry a load
of 1300 KN. The safe bearing capacity of soil is 130 KN/m2. Use M20 concrete and Fe
415 steel. Sketch the details of reinforcements.

20

OR
10.a)

Design a suitable stair for an office building which has a stair room measuring 2.6m x
5.0m. The height of the floor is 3.6m. Live load is 4 KN/m. Sketch the reinforcement
details. Wall = 230mm. R=150mm T=250mm. Adopt M25 concrete and Fe 415 steel.

**************

20

You might also like