How to to replace Motherboard without Reinstalling Windows

This article is for users that want to replace Motherboard on their computers
without reinstalling the Windows Operating System and keep all programs,
files & settings untouched.

Consider the following scenarios:

1. You want to upgrade your main computer parts (mainboard, CPU, RAM,
etc.) but you want to keep your current Windows installation, in order to keep
your program settings & files untouched and not reinstall them from the
beginning.

2. You want to to change the SATA hard disk controller mode from IDE to
AHCI or RAID (or vice versa) in BIOS in order to succeed better performance
or compatibility.

If you come in one of the above scenarios, then you will may realize that
Windows cannot boot and crash with a BSOD (Blue Screen Of Death) error
"STOP 0x0000007B INACCESSABLE_BOOT_DEVICE". This is happen because
Windows cannot find the correct drivers for the SATA hard disk controllers. To
bypass this problem and to avoid to reinstall Windows, you must "tell"
Windows using the Windows Registry, to use the Standard SATA Hard Disk
Controller driver during startup. To accomplish this, just follow the steps
below to make the appropriate modifications in Windows Registry and then
Windows will boot up normally to Windows. After boot, they will install the
necessary hard disk controller drivers according to BIOS hard disk SATA
controller's mode settings e.g. IDE Compatible mode (aka Legacy or ATA
Compatible) or AHCI or RAID mode.

How to tell Windows to use the Standard SATA hard disk controller driver via
Windows Registry.

Before continue please read and then follow the instructions mentioned in
one of the following scenarios, according your situation:

Scenario 1: You haven't replace the motherboard yet (in order to upgrade
your computer) and your computer starts (boot) normally to Windows. In this
case you have to modify the registry from the current working Windows
environment before proceeding to computer upgrade.

Scenario 2: Windows fails to boot because:

You have already replace the motherboard, OR because

In this case you have to use an Offline Registry Editor to modify registry
settings.

Scenario 1: Modify Registry before you replace (upgrade) the mainboard on

Use these instructions only if you haven't replace your motherboard yet and
Windows starts normally . If you have already replace the motherboard
and/or Windows cannot boot, then follow the instructions in Scenario 2.

1. Boot Windows normally and then open Windows Registry Editor. To do that:

Press Windows Image-201_thumb_thumb_thumb_thumb1_t + R keys

Type regedit and press Enter.

image_thumb6_thumb

IMPORTANT: Before you continue to modify the registry, first take a registry
backup. To do that:

a. From main menu go to File & select Export.

2. Inside Windows Registry, navigate (from the left pane) to this key:

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\msahci

image

3. At the right pane double click at 'Start' DWORD value and change its value
data to 0 (zero). Click OK when finish.

image

4. Now perform the same modification to this key:

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\pciide

image

image

5. If you use RAID (otherwise ignore this step) then you have to perform the
same modification to this key:

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\iaStorV

6. Close Registry editor.

That's it! Now you 're ready to continue with your computer upgrade. When
done, enter you BIOS settings and specify the SATA mode (IDE-ATA, AHCI or
RAID) according your needs or leave the default setting. Exit BIOS settings
and start Windows. Windows should start without problems. and install the
required hard disk controller drivers. When Windows finishes the driver
installation, continue to install the rest device drivers for your new
motherboard..

Scenario 2: Windows fails to boot: Modify registry using an OFFLINE registry

Use these instructions only if Windows fails to boot because you have
already replace your motherboard or because you have changed the SATA
controller mode in BIOS.

In this scenario you have to use an offline Registry editor to modify the
Windows Registry. For this task, I prefer to use the Windows Recovery
Environment found on Windows 7 or Windows Vista installation DVD. To open
Registry Editor from the Windows Installation DVD follow the process below:

1. Place the Windows Installation DVD on your CD/DVD drive and boot your
computer from the Windows installation DVD.

Notice: In order to boot from the DVD, you must set the CD/DVD device as
the first boot device in BIOS settings. To do that:

Power On your computer and press "DEL" or "F1" or "F2" or "F10" to enter
BIOS (CMOS) setup utility.
(The way to enter into BIOS Settings depends on the computer
manufacturer).
Inside BIOS menu, find the "Boot Order" setting.
(This setting is commonly found inside "Advanced BIOS Features" menu).
At Boot Order setting, set the CD/DVDRW device as the first boot device.
Save and exit from BIOS settings.

2. At the first screen press Next.

image

3. At the next screen, select "Repair your computer".

image

4. At System Recovery Options (1st screen) click Next.

image

5. At Choose a recovery tool screen, choose Command Prompt.

image

6. At command window type "regedit" (without quotes) & press Enter.

image

In Registry Editor:

7. Highlight the HKEY_LOCAL_MACHINE key.

image

8. From File menu select Load Hive (to load the offline registry).

image

9. Navigate to the disk where Windows installed on (e.g. "C:").

10. Open the system file found in "%Windir%\system32\config\" directory.

image

11. Type a Key Name for the offline registry (e.g. "Offline") and press OK.

image

12. Double-click to expand the HKEY_LOCAL_MACHINE key and you should a

image

13. Expand this new key & navigate (from the left pane) to this subkey:

HKEY_LOCAL_MACHINE\Offline\ControlSet001\services\msahci

image

14. At the right pane double click at Start (DWORD) and change its value data
to 0 (zero). Click OK when finish.

image

15. Perform the same modification to this subkey:

HKEY_LOCAL_MACHINE\Offline\ControlSet001\services\pciide

image

image

16. If you use RAID (otherwise ignore this step) you have to perform the same
modification to this key:

HKEY_LOCAL_MACHINE\Offline\ControlSet001\services\iaStorV

17. When you finish with the modifications, highlight the key you created
before (e.g. "Offline") and from the File menu choose Unload Hive to write
back the changes you made to the offline Registry.

image

18. Close the Registry editor, the Command prompt window and Restart your
computer.

19. Enter BIOS settings and specify the SATA mode (IDE-ATA, AHCI or RAID)
according your needs or leave the default settings.

20. Exit BIOS settings, remove the Windows Installation DVD from the
CD/DVD drive and let Windows to start normally.

Windows should start without problems and then will install the required hard
disk controller drivers.

That's it!