International Journal of Advanced Scientific and Technical Research

Available online on http://www.rspublication.com/ijst/index.html

Issue 3 volume 6, Nov.-Dec. 2013

ISSN 2249-9954

_____________________________
Chloride ion migration/diffusion through concrete and test methods
Altaf Ahmad1, Anil Kumar2
Dept. of Engg. Chemistry, Al-Kabir Polytechnic, Mango, Jamshedpur, India
2
Dept. of Applied Science and Humanities, National Institute of Foundry and Forge
Technology (NIFFT), Hatia, Ranch, India
Abstract:
In the present day models for the life of concrete structures, the causes of failure have been
earmarked and role of chloride ion has been placed at the top, because of comparative ease of
Cl- transport in concrete structure and its extraordinary damaging effect on the existing
passivating film on the rebar surface. Therefore, diffusion of Cl- ions through concrete media
has been given pronounced recognition and various testing techniques for the measurement of
diffusion of Cl- have been developed and standardized.
1

Keywords: Diffusion, interdiffusion, diffusion coefficient, Ficks laws, pore solution,

AASHTO permeation test, Nordtest, immersion test.

1. Introduction:
Concrete is a composite cement based material which is multi component, micro-porous and
microstructure sensitive construction material. It provides fluid flow channels associated
with ion transport and this fact causes important phenomena like diffusion of gases, ions
(particularly Cl- ions etc.), all of which deteriorate the life expectancy of concrete and also of
rebar embedded concrete. Migration, particularly penetration of chloride ion in the form of
diffusion, has become the most important topic because of its role in damaging the concrete
structures. Resistance to damage, or in other words, the life of reinforced concrete depends on
the effective passivation of the rebar steel, which depends upon the alkalinity (that is OH- ion
concentration)of the moist concrete. The effective passivation due to OH- ion is adversely
affected by the presence of Cl- ion in particular and carbonation of the concrete which
actually reduces the concentration of OH- ion.
In case the OH- ion concentration is lower than 11.5, the adherence of oxide film on
the rebar surface is disturbed and become less protective. In the case when the concrete
around the rebar is carbonated and the concentration of OH- ion gets reduced in the pore
solution, the similar result is observed. It occurs in one or more of the following ways: as the
CO2 molecule penetrate into the concrete it reacts with Ca(OH)2 with C S H gel, with
alkali and also with Ca++ ions in pore solution, resulting drastic decrease in the alkalinity of
the pore solution to the level of about pH 8. Then this carbonation front progresses to the
surface of the reinforcing bar, depending on depth of the concrete cover and on the rate of
diffusion of CO2 and time.
It has been noted that films of ferric oxide are more resistant to chloride ion than the
ferrous oxide films which are prone to soluble complex formation with ClFe(OH)2 + Cl- =
[FeCl]x
This means, the presence of Cl- ion in the pore solution will continuously attack
Fe(OH)2 coverage on the reinforcing bar (this is due to auto-catalytic reaction tendency of Clions), which may lead to local pitting due to the continuous and repetitive attack. Actually
there could be a competition between passivation process (ferrous oxide film changing to
ferric oxide) and ferrous oxide film forming complex with Cl- ion (i.e. deterioration of film).
But, a higher OH- ion concentration provides the stability of ferric oxide film. Here the role
of dissolved oxygen is in favour of normal passivation route by primarily directing
conversion of ferrous to ferric oxide. As a result the zones of low dissolved oxygen content

_______________________________________
R S. Publication (http://rspublication.com), [email protected]

Page 151

International Journal of Advanced Scientific and Technical Research

Available online on http://www.rspublication.com/ijst/index.html

Issue 3 volume 6, Nov.-Dec. 2013

ISSN 2249-9954

_____________________________
will suffer pitting attack. The above analysis indicates the role of hydroxide to Cl-ratio in
controlling the onset of pitting corrosion.
Thus the depassivation due to chloride ion is a function of net balance between
competing processes stabilization / repair of the film by OH- and disruption of the film by
Cl- ion. It is expected therefore that there is a threshold (or critical) chloride ion concentration
that must be exceeded before depassivation can take place.
The threshold value is a function of pH (Fig.1). But most specifications do not address
Cl-/OH- for the purpose of life prediction, these rather refer only to total Cl- concentration in
the concrete. For example, a recommendation indicates that the chloride content be smaller
than 0.2% of the cement content of the concrete [1]. It should be taken into account that it is
only the chloride dissolved in the concrete pore solution that functions to depassivate the
steel.

Fig.1 Relations between threshold chloride ion concentration and the pH level of the pore
solution as suggested by Hausman [2] and Diamond [3].
Now, there may be various sources of chloride ordinarily found in concrete e.g., it may
come as an admixtured component or in chloride contaminated aggregates or mixed water,
salt spray salt placed on concrete pavements. In case if chlorides were not incorporated in the
original concrete, then penetration of Cl- ions to the vicinity of steel rebar is controlled by the
concrete cover (i.e. depth of cover) and also by other factors like moisture content, pore
structure and the nature of concrete admixtures used. In the similar way CO2 penetration is
affected by the above factors. The concrete cover also plays a role by providing path for ionic
current between anodic and cathodic portions of the rebar surface, for continuation of
corrosion. For example: (i) if the cover is un-cracked the diffusion and the electrical
resistance are controlled by pore structure and the degree of saturation of the pores. Actually
the un-cracked concrete cover acts as a barrier to diffusion of Cl- ions (and also CO2 gas and
dissolved O2). The diffusion of all these species are sensitive to pore structure of the concrete.
Whereas chloride diffusion occurs mainly through solution, CO2 diffuses in the gas phase and
oxygen may diffuse either as dissolved molecules in solution or in gas phase. (ii) If the
concrete cover is cracked, the width and shape of the cracks control the rate of entry of Clions, and also carbonation [4-5]. Summing up these processes, it appears that the fundamental
modes of transport of Cl- ion in the concrete are diffusion, capillary absorption, evaporative
transport and hydrostatic pressure. Movement of chloride ion under a concentration gradient

_______________________________________
R S. Publication (http://rspublication.com), [email protected]

Page 152

International Journal of Advanced Scientific and Technical Research

Available online on http://www.rspublication.com/ijst/index.html

Issue 3 volume 6, Nov.-Dec. 2013

ISSN 2249-9954

_____________________________
is known as diffusion, which means Cl- ion concentration on the outside surface of the
concrete is greater than on the inside, which allows a natural flow of Cl- ion from regions of
high concentration to low concentration. This is the principle mechanism which drives Clions in the pore structure of concrete [6-7]. These pores are interconnected interstitial spaces
between the gel particles, occupying about 28% of the total volume of gel. Actually gel pores
are much smaller in size than the capillary pores, being in the range of 0.5 2.5 nm. The total
volume of gel pores increases along with the volume of gel as the hydration proceeds.
However the volume of capillary pores decreases with the progress of hydration.
The process of capillary absorption occurs when the dry surface of concrete is
exposed to moisture (containing chloride).In this case the solution is drawn into the porous
matrix of concrete by the process of capillary suction (like sponge). It may however reduce
the distance that chloride ion must travel by diffusion [8].Concrete being a porous materials,
it absorbs water when the water comes in contact, because of the suction in the pores caused
by capillary action. This action depends upon surface tension, viscosity, density of the liquid,
the contact angle between the water and the pore walls and on the radius of the pore.
However the contact angle is small due to the presence of molecular attraction between water
and cement paste.
The mechanism of evaporative transport is a result of vapour conduction from a wet
surface to a drier surface. This means a body of liquid in the pore structure of the concrete
evaporates and leaves deposits of chloride inside.
Permeation is another mechanism of chloride ingress which is driven by the
hydrostatic pressure gradient. This gradient provides the required force to move the liquid
containing the chloride ions through the internal concrete matrix. For example a constant
wave function or retained body of water (in bridges, piers, docks etc.) may give the necessary
hydrostatic pressure gradient in marine environment [9].
Among the above methods of chloride ion transport the most familiar method is
movement of Cl- ion under concentration gradient. For this, the concrete must have a
continuous liquid phase having a chloride ion concentration gradient. It may be noted that in
the bulk of the concrete the pores remain saturated and the chloride movement is controlled
by the concentration gradient.
2. Factors governing Cl- Penetrability (Chloride Penetration into Concrete
Structure):
Chloride ion penetration into Concrete Structure is mainly described in terms of pore
structure of the concrete, which at the first instance, is controlled by the raw materials, the
actual practice being followed and the age. Thus chloride penetrability can be explained as
being influenced by the following factors.
(i) Water-Cement ratio of the concrete: this ratio is affected by the use of supplementary
cementing materials which may subdivide the pore structure.
(ii) Aging/degree of hydration: with aging of the concrete, greater amount of hydration can
be expected, which result into more highly developed pore structure.
(iii) Use of supplementary cementing materials: there are many such materials (such as fly
ash) which require longer time to hydrate, [10-11] affecting the chloride penetration.
(iv) Effect of temperature on pore structure: the effect of temperature (high temperature)
during casting/curing of concrete accelerates the curing process. Thus, as the concrete
ages, temperature affected cured concrete will be more matured. As a result this will
have better resistance to Cl- ion penetration than normally cured material. However as
the normally cured concrete ages, this has a chance to hydrate more fully. In this case,
some research findings have indicated a lower Cl- ion diffusion coefficient than the
high temperature cured concrete [12-13]. This conclusion has been attributed to the

_______________________________________
R S. Publication (http://rspublication.com), [email protected]

Page 153

International Journal of Advanced Scientific and Technical Research

Available online on http://www.rspublication.com/ijst/index.html

Issue 3 volume 6, Nov.-Dec. 2013

ISSN 2249-9954

_____________________________
coarse structure i.e. initially developed in the high temperature cured concrete due to
its initial rapid hydration as well as the possible development of internal microcracking.
(v) Binding capacity: theoretically, concrete is not inert to chlorides in pore solution, a
fraction of Cl- ion will always react with concrete matrix, in the form of chemically or
physically bound, and once bound, it will reduce the rate of diffusion. Therefore the
rate of Cl- ion penetration into concrete will be affected by the Cl- ion binding capacity
of the concrete. Again, once the steady state condition is reached, and the diffusion
coefficient is measured then all the binding can be presumed to have taken place, and
then the effect of binding capacity cannot be observed. However, so long the steady
state condition has not been reached, the binding capacity will affect the results. The
role of supplementary cementing materials on binding capacity have been studied by
many [14-16] with no conclusive remarks.
(vi) Role of C3A content: the C3A content of cement has been found to positively influence
the binding capacity i.e. it increases binding as observed by many [17-19].
2.1 Pore Structure:
Among the various factors responsible for the deterioration of rebar/concrete bond,
ingress of chloride ion is most important, because (as explained earlier) of its role in the
depassivation of the rebar surface. Ordinarily, although under the alkali condition the rebar
surface remains passivated, yet the environment inside the concrete remain vulnerable to
entry of different species, because the cement paste in its formative hydration period contains
pores, which are occupied by evaporable water and during prolong hydration, the products of
hydration fill the space, reducing the volume of interconnected capillary system. Thus this
volume fraction of capillary pores depends on w/c ratio and degree of hydration. When
cement reacts with water, the reaction product has smaller volume than the substance of
hydration, which is due to chemical shrinkage. This difference in volume leads to pore
formation, and as long as water and unhydrated cement are present, these pores can fill up
with cement hydration products: It has been observed that capillary porosity cannot be
avoided but capillary discontinuity is achieved after two weeks of hardening for w/c < 0.5,
requires six months for w/c = 0.6 and is practically not possible for w/c > 0.7 [20-22].
Pores ranging in size from a few nm to several m are generally considered capillary
pores [23-25]. Interlayerspaces of CSHgel are referred to as gel pores of a few nm [26-27].
In addition,macropores (air voids) also exist in concrete owing to entrapped air bubbles and
incomplete compaction (mm in size) [23-25]. In the interfacial transition zone (ITZ) the
capillary porosity is generally higher with better interconnectivity and also the hydration
products are different [28].
2.2 Pore solution:
For certain specific laboratory tests simulated pore water solution (called pore solution) is
prepared in which the rebar is dipped for performing different kind of studies. The pore
solution is prepared with 0.002 M Ca(OH)2 + 0.045 M NaOH + 0.26 M KOH at pH 13.5 [2931]. Also, there are many other simulated solutions in which experiments can be conducted
[32-33].

2.3 Moisture Content:

_______________________________________
R S. Publication (http://rspublication.com), [email protected]

Page 154

International Journal of Advanced Scientific and Technical Research

Available online on http://www.rspublication.com/ijst/index.html

Issue 3 volume 6, Nov.-Dec. 2013

ISSN 2249-9954

_____________________________
At a given pore structure, water in the concrete can be present in different forms [3435], e.g.,chemically bound water (combined in hydration products), interlayer water (held in
gel pores), adsorbed water (on the pore walls), capillary water (held in capillaries) and water
in macropores and air voids. At full hydration ( = 1), the amount of chemically bound water
which depends upon degree of hydration is generally at 0.23 0.25 g. water / g. cement [26].
When water has evaporated from pores, a layer of adsorbed water is still present on
the pore walls regardless of pore size. The thickness of adsorbed layer depends upon the
relative humidity in the pores and other related factors like available internal pore surface. It
may be noted that capillary pores hold water by capillary forces, which are again dependent
upon temperature, relative humidity etc. Macro-pores have no capillary action and thus only
fill up when concrete is submerged.
2.4 Permeability and Transport:
The presence of pores may be seen as the efficient system for transport of liquids and gases,
which are responsible for deterioration or durability of the reinforced concrete [23,
35].However, the transport of gel water or adsorbed water is under the effect of surface
forces. Transport properties are proportional to the extent of capillary pores and their
interconnectivity which was observed in experiments on the coefficient of permeability for
stationary water transport in cement paste vs. the volume fraction of capillary porosity. It was
found that both pore structure and the presence of capillaries strongly depended on w/c ratio
(and also on degree of hydration). This means that the permeability increases nonlinearly
with increasing w/c ratio particularly above w/c 0.5[36-37].
As noted earlier, water sucked into the concrete is the carrier of dissolved Cl- ions.
Capillary suction becomes dominant mechanism for concrete in the splash zone during the
cyclic wetting and drying process that controls the capillaries, to be filled up or emptied.
However, it was observed that absorption by capillary action was faster than water loss by
evaporation during drying cycles [34-35].
3.0 Critical Cl- content or Cl- threshold value:
The term critical or threshold (Ccrit) Cl- means the concentration required to destroy the
passive film on the surface of steel embedded in concrete. Ccrit mainly depends on pH of the
pore solution. Thus higher the amount of OH- ions, the amount of Ccrit to initiate corrosion
increases [38], anda critical ratio is Cl-/OH- = 0.6 which means, e.g., if the pH is 13 instead of
12, the tolerable Cl- ion concentration is 10 times higher than at pH 12. A high alkalinity of
concrete pore solution offers resistance against Cl- induced corrosion. This gives a necessary
caution before using puzzolanic material (which lowers the pH) for concrete structures.
Ccrit is also influenced by the type of steel/concrete interface, e.g., if the interface is
covered with solid hydration products (particularly in the case of calcium hydroxide) the Ccrit
increases [39-40]. An easy reference of the role of interface is a higher Cl- value of Ccrit is
required for steel embedded in concrete as compared of steel immersed in alkaline solution
[41-43]. It is also important to note that macroscopic or microscopic defects at the
steel/concrete interface are also important factors for Ccrit value.
4.0 Ficks laws:

4.1 Historical Development:

_______________________________________
R S. Publication (http://rspublication.com), [email protected]

Page 155

International Journal of Advanced Scientific and Technical Research

Available online on http://www.rspublication.com/ijst/index.html

Issue 3 volume 6, Nov.-Dec. 2013

ISSN 2249-9954

_____________________________
The phenomenon of diffusion is perceived as a descriptive term for spreading in all direction
from a source and as such this term refers to the net movement of matter, attributed to the
random movement of molecules, taking place from a region of concentration to one of lower
concentration. It has a classical form and numerous variants of this classical form developed
adhoc for specific applications in different disciplines. The notion that diffusion is a physical
process (obeying quantitative laws) and explicable in terms of the behaviour of individual
molecules can be traced to the work of Dalton at the beginning of the 19th century [44](1808).
Another work of Deutrochet (1827) was related to diffusion in liquid systems as a dynamic
counterpart, osmosis [45-46]. Another work was produced by Graham (1833) who found that
gas diffusion dependent in a simple way to the relative molecular mass of gas molecules and
he extended this phenomena to the study of liquids [47-48]. Ludwig and Brcke (1852)
recognized the importance of the matter and studied the phenomena with limited success
[49]. Another study by Pfeffer (1877) showed measurement of osmosis through
semipermeable membrane: Actually, work of Fick confronted this problem in which diffusion
and osmosis were conceived in terms of passage through some kind of physical barrier, a
porous membrane. However Fick (1855) assumed another kind of model in which he
simplified the matter in the form of a mathematical model, giving net rate of solute
movement and local curvature of concentration gradient [50]. This work of Fick (1855) is
widely acknowledged and have established the law of diffusion, inductively from
experimental data. The relationship, known Ficks law of diffusion gives the rate at which the
concentration of the substance at any point x in a system is proportional to the curvature of
the concentration gradient at that point, and the proportionality constant is the diffusion
coefficient or diffusivity (D) in the system. Einstein (1905) and von Smoluchowski(1906)
independently found an explanation for Ficks law in molecular terms [51-52]. Actually these
authors were in search of a critical test for kinetic theory, but they arrived at the explanation
of the phenomena of Brownian motion [52], and in addition they derived the Ficks law as a
macroscopic diffusion process in terms of molecular kinetic mechanism of Brownian motion
in fluid system where there are concentration gradients. Thus we see that the classical theory
comparising Ficks law, the Brownian motion concept and the Einstein von Smoluchowski
model, were developed from a number of scientific advances in 19th and early 20th century
physics and physiology, e.g., the study of Brownian motion, osmotic theory, the theory of
heat conduction, kinetic theory and the study of diffusion per se, the above work of
Einstein and von Smoluchowski further assisted (through the theory of stochastic processes)
Wiener (1964) to study probability distribution of diffusing particles in order to study an
individual particle to pass during a stated interval of time between any two points in a defined
space[53]. This Stochastic theory has been influential in quantum mechanics (e.g. Feynmans
path integral method), in mathematics (Functional analysis, differential equation and
probability theory) and in several other fields [54].
4.2 The Driving Force for Diffusion:
The diffusion occurs only when a concentration gradient exists for example, in an electrolytic
solution. The concentration of an ionic species i, may be assumed to vary in the x direction
but is constant in the y and z directions and one can map equi-concentration surfaces which
will be parallel to the y z plane (Fig. 2).

_______________________________________
R S. Publication (http://rspublication.com), [email protected]

Page 156

International Journal of Advanced Scientific and Technical Research

Available online on http://www.rspublication.com/ijst/index.html

Issue 3 volume 6, Nov.-Dec. 2013

ISSN 2249-9954

_____________________________

Fig. 2 Schematic representation of a slice of electrolytic solution in which the concentration

of a species i' is constant on the equi-concentration surfaces parallel to the yz plane.
The situation pictured in Fig. 2 can also be considered in terms of the partial molar free
energy (or chemical potential, ) of the particular species i' as:

----- (1)
Here ci is a function of x and the chemical potential also is a function of x, i.e., the chemical
potential varies along the x coordinate.
Now, if we assume that the species i has an initial concentration cI at xI to a final
concentration cF at xF, then the change in free energy (or chemical potential) of the system is
(explained in Fig. 3).

----- (2)

Fig. 3 Schematic representation of the work done W in transporting one mole of species i
from an equiconcentration surface where its concentration and chemical potential are c I and
Ito a surface where its concentration and chemical potential are cF and F.
This change in free energy is equal to the net work done on the system in an isothermal,
constant-pressure reversible process. The work done to transport one mole of species i from
xI to xF is

----- (3)

_______________________________________
R S. Publication (http://rspublication.com), [email protected]

Page 157

International Journal of Advanced Scientific and Technical Research

Available online on http://www.rspublication.com/ijst/index.html

Issue 3 volume 6, Nov.-Dec. 2013

ISSN 2249-9954

_____________________________
The above case is comparable to work done (W) in mechanics in which a mass is lifted from
a height XI to XF at the expense of
W = FG (XF XI) = FG X = U,
Where, FG is gravitational force on the body and U = gravitational potential energy.
An infinitesimal change in energy distance relation (in mechanics) will be

Here the negative of the gradient of gravitational potential energy defines the gravitational
force. Similarly the negative of the gradient of electrostatic potential defines the electric
force, and therefore the negative of the gradient of the chemical potential would act formally
like a force. Again, just as the gravitational force results in the motion of a mass and the
electric force results in the motion of a charge, the chemical-potential gradient results in the
net motion (or transfer) of the species ifrom a region of high chemical potential to a region of
low chemical potential. This net flow of the species idown the chemical-potential gradientis
called diffusion, and therefore the gradient of chemical potential may be looked upon as the
diffusion force FD. Thus, one can write

----- (4)

4.3 Fick's First Law (Steady-State Diffusion):

The gradient of chemical potential resulting from a non-uniform concentration is equivalent
to a driving force for diffusion and it produces a diffusion flux, J (i.e. the number of moles of
species i' crossing per second per unit area of a plane normal to the flow direction).
If diffusion is occurring, the driving force FD and the flux J may reach values that do not
change with time (i.e. a steady state), then a relation between the diffusion flux J and the
diffusion force FD can be given by a power series
----- (5)
Where A, B, C, etc., are constants. If FD is less than unity and sufficiently small, the terms
containing the powers of FD (greater than unity) can be neglected and
----- (6)
Here the constant A must be zero; otherwise, it will mean that one would have the impossible
situation of having diffusion even though there is no driving force for diffusion.
Hence the assumption of a sufficiently small driving force leads to the result
----- (7)
i.e., the flux is linearly related to the driving force and a value of FD = 0 corresponds to an
equilibrium situation; but assumption of a small value of FD is required to ensure a linear
relation (Eqn. 7) between flux and force which is tantamount to saying that the system is near
equilibrium, but not at equilibrium.
Now, the driving force on 1 mole of ions being di/dx (Eqn. 4)then if the
concentration of the diffusing species adjacent to the transit plane (Fig. 4), across which the
flux is to be studied i.e. ci moles per unit volume, the driving force FD, at this plane,will be
ci(di/dx). Then the (Eqn. 7) becomes

----- (8)

Using

and assuming ideal behaviour, eqn. 8, becomes

----- (9)
----- (10)

_______________________________________
R S. Publication (http://rspublication.com), [email protected]

Page 158

International Journal of Advanced Scientific and Technical Research

Available online on http://www.rspublication.com/ijst/index.html

Issue 3 volume 6, Nov.-Dec. 2013

ISSN 2249-9954

_____________________________

Fig. 4 Diagram for the derivation of the linear relation between the diffusion flux JI and the
concentration gradient dci /dx.
Thus, the steady-state diffusion flux can be shown to be proportional to the gradient of
concentration. This proportionality existed has been empirically known as Ficks first law of
steady state diffusion:
----- (11)
Where, D is called diffusion coefficient, and
----- (12)
in which B is a constant and therefore it may appears that D also is a constant, but expression
(Eqn. 12) was obtained only because an ideal solution was considered, and use of activity
coefficients were ignored in Eqn. 1. Thus strictly, diffusion coefficient is not a constant but, if
the variation of the activity coefficient is not significant over the concentration difference that
produces diffusion, then for all practical purposes D is a constant. The quantity D can be
understood in a fundamental way only by probing into the ionic movements, the results of
which show up in the macroscopic world as the phenomenon of diffusion.
4.4 Fick's Second Law (Non-Steady-State Diffusion):
The most fundamental differential equation of diffusion in an isotropic medium can be
derived from Ficks First Law (Eqn. 11). So far we have considered steady-state diffusion in
which neither the flux nor the concentration of diffusing particles in various regions changes
with time i.e the whole transport process is time independent. Now, if a concentration gradient
is suddenly produced in the electrolyte initially in a time-invariant equilibrium condition, then
diffusion starts, but it will not immediately reach a steady state that does not change with time.
It means the distance variation of concentration, which is zero at equilibrium, will not
instantaneously reach the final steady-state.
To study the variation of concentration with time, let us consider a Consider a
parallelepiped (Fig. 5) of unit area and length dx through ions are diffusing in through the left
face and out through the right face, as a continuous of x. If c is the concentration of ions at the
left face, the concentration at the right face is

_______________________________________
R S. Publication (http://rspublication.com), [email protected]

Page 159

International Journal of Advanced Scientific and Technical Research

Available online on http://www.rspublication.com/ijst/index.html

Issue 3 volume 6, Nov.-Dec. 2013

ISSN 2249-9954

_____________________________

Fig. 5. The parallel piped of electrolyte used in the derivation of Fick's second law.
From Ficks law (Eqn. 11), the flux into the left face J L is
-----(13)
and the flux out of the right face is
-----(14)
The net outflow of material from the parallelepiped of volume dx is
-----(15)
The term
is the net outflow of ions per unit volume per unit time. This net
outflow of ions is variation of concentration with time, i.e., dc / dt, and therefore the eqn. 15
can be written as
----- (16)
Where, the partial differential equation has been used because the concentration depends both
on time and distance (c = f(x, t)). If the diffusion is one dimensional i.e. if there is gradient of
concentration only along the X-axis, eqn. 16 is generally referred as Ficks second law of
diffusion.
4.5 Diffusion of Cl- ions in concrete:
Ficks First Law describes the flow of a substance (e.g. impurity) showing that the rate of
diffusion of the substance across a plane is proportional to the concentration gradient across
the plane. In case of Cl- ion diffusion into concrete, the diffusion process in one dimensional
and Ficks law (steady state diffusion) is applicable. The rate of diffusion includes the effect
of porous matrix of concrete that contains both solid and liquid components. This equation
can only be used after a steady state condition is obtained because the equation does not
involve the change in concentration in time.
The Ficks Second Law involves changes of concentration gradient with time in the form:
------- (17)
If the following boundary conditions are assumed: surface concentration of Cl-is
constant (C(x=0, t>0) = Co), initial concentration in the concrete is zero (C(x>0, t=0) = 0)
and the concentration at an infinite point far enough from the surface is zero (C(x=, t>0) =
0). The equation was reduced (Cranks solution), [55] as follows:

_______________________________________
R S. Publication (http://rspublication.com), [email protected]

Page 160

International Journal of Advanced Scientific and Technical Research

Available online on http://www.rspublication.com/ijst/index.html

Issue 3 volume 6, Nov.-Dec. 2013

ISSN 2249-9954

_____________________________
-------- (18)
where,

C(x,t) =chloride concentration, measured at depth x and exposure time t (%

mass)
t = the exposure time (sec)
erf =error function (tables with values of the error function are given in
standard mathematical reference books).
The Crank's solution to Fick's Second Law of Diffusion [55] can also be presented in
the following form:
-------- (19)
Where Ci= initial chloride-ion concentration of the cementitious mixture prior to the
submersion in the exposure solution (% mass). A common method of determining the
chloride diffusion in concrete is to expose saturated samples to a chloride solution for a
known period of time. The chloride concentrations at varying depths are then obtained and
diffusion coefficients and surface chloride concentrations are determined by fitting the
profiled data to the non-linear Fick's Second Law of Diffusion solution [56].
5.0 Testing techniques for diffusion of Cl-:
Testing techniques have been designed primarily for measurement of diffusivity of
chloride ions with aim to simulate practical conditions. Naturally, therefore, depending on
outlook of the test the techniques are different. For instance, some tests involve slow
migration of chloride ion, whereas some tests carry out the experiments at faster rate. In some
cases the migration have been enhanced by application of external voltage, which therefore is
no more auto-migration, rather it may be termed as enforced migration. Generally in the
measurement of D (Cl- ion), no difference is underlined between the auto/enforced migration,
although there should be a difference to be underlined. There are many national/international
specifications for the measurement of D, all of which utilize equations for Ficks diffusion.
5.1 Interdiffusion study (I-& Cl-):
This method involves the study of interdiffusion of I- and Cl- ions and the tracer diffusion of
Cs+ ions in water saturated OPC at 30 0C, as a function of w/c ratio (during fabrication) [57].

Fig. 6 Schematic diagram of the diffusion cell [57].

_______________________________________
R S. Publication (http://rspublication.com), [email protected]

Page 161

International Journal of Advanced Scientific and Technical Research

Available online on http://www.rspublication.com/ijst/index.html

Issue 3 volume 6, Nov.-Dec. 2013

ISSN 2249-9954

_____________________________
The basic arrangement (Fig. 6) is used to measure intrinsic diffusion coefficient (Di)
in which cement sample forms a partition between two sides of the diffusion cell. Di at steady
state condition is calculated by
(20)
Where, Di is the intrinsic diffusion coefficient (m2 sec-1) of the particular species, V is the
volume of the low concentration side of the cell (i.e. C2), l is the thickness and A is the cross
section area of cement specimen.
Result established:
i) The diffusion of ion is a strong function of w/c ratio
ii) The apparent activating energies for Di are significantly affected by irreversible thermally
induced changes in the pore structure particularly during the heating part of thermal cycle.
5.2 AASHTO T259 (Salt Ponding Test):
In this test [58] concrete samples (three slabs each of 75 mm thick and 300 mm2 surface area)
are covered on the sides, the top surface (300 mm2) is kept open where ponding is made with
3% NaCl solutions and the bottom surface is connected to an atmosphere of 50% relative
humidity. A schematic representation is given in (Fig. 7).

Fig. 7 AASHTO T259 (Salt Ponding) test Setup [58]

The concrete slabs were moist cured for 14 days and then stored in a drying room at 50%
relative humidity for 28 days. The sides of slabs are sealed. After this conditioning treatment,
a 3% NaCl solution is ponded on the top surface for 90 days. During this time the bottom
surface is exposed to drying environment (50% relative humidity). After this period the slabs
are removed and the chloride concentration is determined in 0.5 inch thick slices parallel to
the ponding surfaces.
The salt ponding test was found to be too crude, because it does not give proper
chloride ingress profile. Beside there is an initial sorption effect when the slabs are first
exposed to solution, when salt solution is drawn quickly into the pores of the concrete.
Another factor is that the exposure of bottom face to a 50% relative humidity environment
during the test causes chloride to be drawn into the concrete through a mechanism other than
the diffusion. Another factor by which vapour transmission from wet front in the concrete to
the drier atmosphere at external face takes place, which may also carry chloride ions. This
effect is called wicking. It was noted that chloride migration by capillary absorption in this
test is not comparable to life time chloride diffusion behaviour of the structure.

_______________________________________
R S. Publication (http://rspublication.com), [email protected]

Page 162

International Journal of Advanced Scientific and Technical Research

Available online on http://www.rspublication.com/ijst/index.html

Issue 3 volume 6, Nov.-Dec. 2013

ISSN 2249-9954

_____________________________
5.3 Nordtest NT Build 443 (1995) (Bulk Diffusion Test):
This Nordic test [59]was developed to overcome some of the deficiencies of salt ponding test
and was based on the immersion test APM 302 [60]. As compared to test method of APM
302, in this case the test specimen is saturated with lime water. This method prevents any
initial sorption effect when chloride solution is used. In this test other than the top surface all
other surfaces are sealed and the top surface is uncovered and exposed to 2.8 M NaCl
solution (Fig. 8). It is left this way 35 days (minimum).

Fig. 8 Nordtest Setup

For chloride analysis milling of surface at depth increament on the order of 0.5 mm
are made and the chloride content of the powder is determined according to AASHTO T260
[61]. The error function solution of Ficks second law is then fit to the curve and a diffusion
value and surface chloride concentration is determined.
(21)
The test is recommended to be carried out for a period extended to 90 days or longer
for higher quality concretes and also for modelling purpose.
5.4 Nordtest NT Build 492 (Non-Steady State Migration Test):
The Nordic standard NT BUILD 492 [62] was based on the CTH Rapid Test [63], with some
modifications [64].
The test procedure involves:
Vacuum saturating the specimen by using AASHTO T277 [65];
Mounting the specimen in the migration cell (a silicon rubber tube) and filling the
downstream cell with 0.3 N NaOH solution (anolyte);
Placing the cell in the upstream reservoir (a plastic box) containing 10% NaCl
solution (catholyte);
Applying an external potential of 30 V DC between the two electrodes and adjusting
the potential (in a range of 10 to 60 V DC) according to the initial current so as to
keep the power consumption of the specimen in most cases less than 2 W;
After test (usually 24 hours), the specimen is axially splitted into two pieces;
Spraying 0.1 M AgN03 solution on one of the freshly split surfaces of the specimen
and, when the white silver chloride precipitation on the split surface is clearly visible
(about 15 minutes), measuring the penetration depths across the split surface at
intervals of 10 mm to obtain 5 to 7 valid depth readings;

_______________________________________
R S. Publication (http://rspublication.com), [email protected]

Page 163

International Journal of Advanced Scientific and Technical Research

Available online on http://www.rspublication.com/ijst/index.html

Issue 3 volume 6, Nov.-Dec. 2013

ISSN 2249-9954

_____________________________
The chloride diffusion coefficient, Dnssm is then calculated from the equation:
(22)
Where xd is the average value of the penetration depths, t is the test duration, and can be
taken as a laboratory constant.
(23)
5.5 Nord Test NT Build 355 (Steady State Migration Test):
The Nordic standard NT BUILD 355 [66] was developed earlier (1980's) and revised in
1990's. This is a steady state migration test, which has following procedure.
Coating the curved surface of the specimen with epoxy resin;
Saturating the specimen by immersion in saturated lime water until the weight
changes by not more than 0.1% per day;
Mounting the specimen between the migration cells and filling the upstream cell with
5% NaCl solution and the downstream cell with 0.3 N NaOH solution;
Applying an external potential of 12 V DC between the two cells and measuring the
actual potential drop across the specimen by using two reference electrodes;
Qualitatively checking the downstream cell for chlorides by using slightly acidified 1
M AgN03 solution until a white precipitate can be observed;
Quantitatively determining chloride contents in the downstream cell at least once a
day over at least seven days by using a standardized method;
Performing linear regression analysis of at least five points of the linear part of the c-t
(concentration-time) curve until a linear correlation coefficient of at least 0.9 is
obtained;
Calculating the chloride flux J from the slope of the linear regression.
The chloride diffusion coefficient, Dssm, is then calculated using the following equation:
(24)
Where,
Dssm: chloride diffusion coefficient (steady state migration)
R:
gas constant, R = 8.314 J/(K-mol);
T:
average value of the initial and final temperatures in the anolyte solution (K);
L:
thickness of the specimen (m);
z:
absolute value of ion valence, for chloride, (z=1);
F:
Faraday constant, F = 9.648 x 104 J/(V-mol);
E: absolute value of the potential difference between the upstream solution
and the downstream solution, measured by using two reference electrodes (v);
c1, c2: chloride concentration in the upstream and downstream cell, respectively.
Kg/m3
J:
chloride flux, kg/(m2s);
V2: volume of the downstream cell, (m3);
A:
cross-sectional area of the specimen, (m2);
c2/ t: slope of the concentration-time plot, (kg/m3s).
Although this method gives sufficient precision for moderately permeable concrete,
yet the reproducibility is poor in case of low permeability concrete.

_______________________________________
R S. Publication (http://rspublication.com), [email protected]

Page 164

International Journal of Advanced Scientific and Technical Research

Available online on http://www.rspublication.com/ijst/index.html

Issue 3 volume 6, Nov.-Dec. 2013

ISSN 2249-9954

_____________________________
5.6 AASHTO T277: Electrical Indication of Concretes Ability to Resist chloride Ion
Penetration (Rapid Chloride Permeability Test) (ASTM C1202):
In this test [67] a water saturated, 50 mm thick, 100mm dia concrete specimen is subjected to
60 V DC voltage for six hours, as shown in (Fig. 3).

Fig. 9 AASHTO T277 (ASTM C1202) test set up.

The figure shows, that two stainless steel electrode (surfaceperforated) are placed on two
sides. On one side a reservoir contains 3.0% NaCl solution (connected to ve terminal) and
on the other side, the second reservoir contains 0.3 M NaOH solution, its electrode is
connected to +ve terminal. Originally this test was referred to as the Rapid Chloride
Permeability Test (RCPT) although this test does not give permeability. Some objections to
this test are:
i) the current passed is for all ions (not just for chloride ions)
ii) the measurements are before the steady state migration is achieved, and
iii) ahigher voltage may lead to increase in temperature, especially for low quality concretes
[68 72].
Despite these limitations, many attempts have been made to successfully correlate
RCPT values with diffusion coefficients from other tests [73-74].
5.7 Rapid Migration Test (CTH test):
In this test [63] a migration cell is setup with a specimen of 100 mm dia and 50 mm thick and
the applied voltage is kept at 30 volt (Fig. 10). Although the experimental setup is similar to
other electrical migration test, in this case the chloride concentration of the downstream
solution is not monitored and after specified duration of test (8 hrs) the samples are removed
and split and the depth of chloride penetration is determined in one half of the specimen using
colorimetric technique, in which the AgNO3 solution is used (i.e. sprayed) as indicator. The
chlorides bind with silver to produce whitish silver chloride. In the absence of chlorides, the
silver bonds with hydroxides of concrete giving brownish colour. Otsuki 1992 [75]
determined that the optimum concentration of AgNO3 to be used is 0.1N solution that gives a
colour change corresponding to the location of a soluble chloride concentration of 0.15% by
weigh of cement.

_______________________________________
R S. Publication (http://rspublication.com), [email protected]

Page 165

International Journal of Advanced Scientific and Technical Research

Available online on http://www.rspublication.com/ijst/index.html

Issue 3 volume 6, Nov.-Dec. 2013

ISSN 2249-9954

_____________________________

Fig. 10 Tang and Nilsson migration cell .

The above experiment examines the total chloride content and the soluble chloride percentage
to determine whether the chloride comes from external sources or from initial mixing, the w/c
ratio of the concrete.
The depth of penetration can be used to determine Cl- ion diffusion coefficient from
the Nernst-Einstein equation [63].
(25)
Where, Xf is the injection point of chloride ion profile, which is related to the depth given by
the colorimetric technique.
This CTH test has been found to be more useful than RCPT related examination of
actual Cl- ion movement and temperature rise.
5.8 Resistivity Technique:
Another method [76] for assessing the ability of chlorides to penetrate concrete uses electrical
resistance and conductivity measurement. The conductivity of saturated porous medium
(concrete) is primarily determined by the conductivity of pore solution and is given by a term
formation factor (FF).
where, is the conductivity of the porous material and 0 is the conductivity of the pore
solution. However the conductivity and the diffusivity in a porous medium are both related to
same factors, e.g. tortuosity, constrictivity, pore size and connectivity and are given by,

Where, D is the diffusivity of the porous medium and D0 is the diffusivity of the chloride ion
in the pore solution [77].
There are two types of test to determine the resistivity value involving direct current
or alternating current [76]. The measurement of alternating resistance can be done by placing
a test specimen (concrete) between two electrodes and applying an A.C. voltage and
monitoring current to determine a resistance value. Direct current resistivity is measured by

_______________________________________
R S. Publication (http://rspublication.com), [email protected]

Page 166

International Journal of Advanced Scientific and Technical Research

Available online on http://www.rspublication.com/ijst/index.html

Issue 3 volume 6, Nov.-Dec. 2013

ISSN 2249-9954

_____________________________
applying a voltage between two electrodes with the concrete sandwiched between them (Fig.
11).

Fig. 11 DC Resistivity measuring device.

Because the concrete conducts electricity as an electrolyte, there is a polarisation effect which
causes the actual voltage (causing current) to be reduced by an amount. If the polarisation
effect is constant at different applied voltages, this can be accounted for by measuring at two
given voltages e.g. for D.C. resistance [76].
(26)
where, R is the resistance, Ea1 and Ea2 are the two applied voltages and I1 and I2 are the
relevant currents. From this resistivity can be calculated using,
(27)
where, is the resistivity, A is the cross- sectional area and L is the length of the specimen.
5.9 Wenners in situ Resistivity Measurement:
Fig. 12 shows an array of probes for determining resistivity of concrete in situ (i.e. without
removing cores to place between plates). An array of four probes is set at four points, at a
constant distance apart a. Between the two outer points the current a current is applied while
between two inner points the potential is measured. This has advantage of eliminating the
influence of polarisation as the actual potential is measured in the inner region. When the
thickness is much greater than the distance between the points (i.e. a semi-infinite region), the
resistivity can be calculated as [78],
(28)
Where, is the resistivity, a is the distance between points, P is the measured potential, and I
is the applied current.

_______________________________________
R S. Publication (http://rspublication.com), [email protected]

Page 167

International Journal of Advanced Scientific and Technical Research

Available online on http://www.rspublication.com/ijst/index.html

Issue 3 volume 6, Nov.-Dec. 2013

ISSN 2249-9954

_____________________________

Fig. 12 Wenner Array Probe .

If the Thickness is not much greater than the distance between the two points, a correction
factor may be used [78]. The resistivity tests avoids heating of the concrete (voltage can be
low 10 volt or lower) [77]. The main drawback of this technique is in its determination of
conductivity of pore solution (either pore solution must be removed from concrete to get
resistivity, or the concrete may be pre-saturated with a solution of known conductivity). Presaturation requires drying of concrete. Drying may lead to damage of pore structure due to
micro-cracking, which may increase the diffusivity [79]. Another important fact is that the
pore solution contains a wide range of ions (alkali hydroxides), which may precipitate if the
concrete is dried (as a necessity before pore saturation). The precipitated ions may affect the
conductivity. As a precaution a highly conductive solution (5M NaCl), [77] is normally used.
In this way, this technique manages to ensure a steady state condition from the start of the
testing procedure. For very high quality concretes, it will be difficult to extract the pore
solution, which is an important disadvantage [80].
5.10 Pressure Penetration Technique:
In this method [81] the flow of chloride ion into concrete is accelerated by exposing one face
of the concrete to a chloride containing solution, which is under pressure. This pressure will
drive the chloride ions into the concrete under both conditions of convection and diffusion
[81]. The method is similar to determining water permeability using a pressure cell, in which
concrete specimen is pre-saturated with water and placed in a permeability cell (with proper
sealing to avoid leakage). Fig. 13 shows the chloride containing solution at one face of the
concrete on top of which pressure is applied for a given period of time, after which the
concrete sample is removed from the cell and tested for chlorides.

_______________________________________
R S. Publication (http://rspublication.com), [email protected]

Page 168

International Journal of Advanced Scientific and Technical Research

Available online on http://www.rspublication.com/ijst/index.html

Issue 3 volume 6, Nov.-Dec. 2013

ISSN 2249-9954

_____________________________

Fig. 13 Pressure Penetration Test Procedure

The proposed condition governing the convection and diffusion is given by eqn. 16 [81].
(29)
Where

is the average linear rate of flow which is [81]

(30)
Where k is the hydraulic permeability, n is the porosity and h is the applied pressure head.
The solution to this differential equation is [81].
(31)
The above equation allows the determination of chloride diffusion coefficient, if a chloride
profile is known at a specific time, which can be obtained as describe below. The depth of
chloride penetration of known concentration of chloride at a specific time can be
conveniently determined using a colorimetric technique (such as AgNO3 spray procedure
explained in CTH test) [5.7]. This value can also be used to determine water permeability the
[82].
(32)
where k is the hydraulic conductivity, n is the porosity, l is the length of the specimen, x d is
the depth of chloride penetration, t is the time over which pressure was applied and h is the
applied head.
5.11 Sorptivity technique:
The term sorptivity is used as a measure of capillary forces exerted by the pore structure
causing fluids to withdrawn unto the body of the material.
For simplicity, the one dimensional flow can be stated as [83].
(33)
Where i is the cumulative water absorption per unit area of inflow surface, S is the sorptivity
and t is the elapsed time. To determine sorptivity of concrete specimen in the laboratory a
simple technique is given in (Fig. 14).

_______________________________________
R S. Publication (http://rspublication.com), [email protected]

Page 169

International Journal of Advanced Scientific and Technical Research

Available online on http://www.rspublication.com/ijst/index.html

Issue 3 volume 6, Nov.-Dec. 2013

ISSN 2249-9954

_____________________________

Figure14. Lab Sorptivity Technique.

For the determination of sorptivity, the concrete specimen is pre conditioned to a certain
moisture condition either by drying the specimen for seven days in an oven at 50 0C or by
drying for four days at 50 0C and then cooling in a sealed container for three days. The sides
of the specimen are sealed with tape. The initial mass of the specimen is taken (time zero)
and then it is immersed to a depth 5 10 mm in water. At selected times (1, 2, 3, 4, 5, 9, 12,
16, 20 and 25 minute) the specimen is removed from water, excess water blotted out and then
the specimen is weighed. It is then replaced in the water and then stopwatch is started again.
The gain in mass per unit area over the density of water is plotted vs. square root of elapsed
time. The slope of the line gives the reported sorptivity. While sorptivity tests can avoid
many of the difficulties of the RCPT, it does have some limitations, such as the following:

5.12

It is only able to evaluate the surface of the concrete, i.e., sorptivity test involving
the time frame will not give any information of the bulk properties of the
concrete. Therefore, in case of high performances services where the steels
(rebars) are at typical depths, the sorptivity results will not be useful.
Another difficulty arises in field tests where moisture content varies drastically,
making sorptivity data unusable [83].
Sorptivity is not a constant property over the long term. Therefore, sorptivity (S i)
obtained at initial exposure, will change (because of additional absorption) to
another sorptivity (Sf) [84].
Sorptivity is not a familier term with construction engineers compared to
permeability or diffusion.
Other electromigration techniques:

5.12.1 Determination of D using Nernst Planck equation:

The use of electrical field for the movement (migration) of chloride ion has been utilized in
many techniques. Such data can also be collected by measuring, in particular, the actual
movement of chloride ion (as opposed to simply measuring the amount of charge passed).
Using Nernst Planck equation [85].

_______________________________________
R S. Publication (http://rspublication.com), [email protected]

Page 170

International Journal of Advanced Scientific and Technical Research

Available online on http://www.rspublication.com/ijst/index.html

Issue 3 volume 6, Nov.-Dec. 2013

ISSN 2249-9954

_____________________________
(34)
The following terms can be measured [85].
Where,
Ji
= Flux of the ionic species (i)
Di
= Diffusion co-efficient of the ionic species (i)
Ci(X) = Concentration of ionic species as a function of location (X)
Zi
= Valence of the ionic species (i)
F
= Faradays constant
R
= Universal gas constant
T
= Temperature
E(X) = Applied electrical potential as a function of X, and
Vi(X) = Convection velocity of ionic species (i).
According to Andrade 1994 [86], when an electric field is applied in an electrolyte, the ions
move due to diffusion (differences in concentration), convection (electrolyte movement) and
migration (differences in potential), which is represented in the equation above (Eqn. 34).
Now in such situation, where there is no pressure or moisture gradient (no convection) and
assuming that the diffusion is negligible as compared to the electrical migration (which is
sufficiently reasonable if the applied voltage is about 10 15 volt) the equation (Eqn. 34)
becomes [86].
(35)
Also one can have from above equation
(36)
Where,

= Activity co-efficient
l
=concrete disc thickness (cm.)
JCl
= Flux of chloride ion (mol/cm2.S)
Therefore the above simplification for D can be utilized once the chloride ion flux is
known and if it is assumed that the voltage drop across the cell is linear.
5.12.2 Determination of D using Nernst Einstein equation:
It has been discussed that Ficks law can be used to determine diffusion of migrating
ion with the help of the standard solution of the equation [17]. However in this diffusion
process, the fluxing species must not react with the matrix, and matrix is homogeneous in
structure and composition. If the concrete is considered to be a solid electrolyte, the
diffusivity of the charged species i in concrete is related to its partial conductivity, as given
by Nernst Einstein equation [87].
(37)
Where,
Di
= Diffisivity of species i (cm2/s).
R
= Universal gas constant (8.314J/mol. K)
T
= Absolute temperature (K)
i
= Partial conductivity of species i(S/cm)
Zi
= Charge ofspecies i
F
= Faradays constant (96500 Coulomb/mol)
Ci
= Concentration of species I (mol/cm3).

_______________________________________
R S. Publication (http://rspublication.com), [email protected]

Page 171

International Journal of Advanced Scientific and Technical Research

Available online on http://www.rspublication.com/ijst/index.html

Issue 3 volume 6, Nov.-Dec. 2013

ISSN 2249-9954

_____________________________
The partial conductivity i is given as,

ti
= Transference no. of species i

= Conductivity of concrete

(38)

Also,
(39)
Where, Qi and Ii are the amount of charge and current contribution of the species i to the
total electric quantity Q and current I, respectively. This means if the diffusivity of an ion is
to be determined by the Nernst Einstein equation, the transference number of the ion must
be known, however a simpler approach is to take ti = 1.0. This is in agreement with the results
obtained from laboratory and field data for ordinary concrete, Portland cement and mortar [88
103].
5.12.3 Test method on Nernst Einstein equation:
5.12.3.1 Method 1
Page et al [104] studied the effect of cement matrix variables on diffusion of chloride ions
in concrete. The principle aims to establish a simple technique for study of chloride diffusion
kinetics in mature cement pastes and to explain the effect on diffusion of the following
factors.
1. w/c ratio and temperature for specimens of constant cement composition.
2. Curing condition and interfacial segregation for specimens of fixed cement
composition and w/c ratio at constant temperature.
3. Variation in cement composition for specimens of fixed w/c ratio at constant
temperature.
Experimental Cell: The figure (Fig. 15) below shows a two compartment cell, in which the
samples were made from cement paste (with desired w/c ratio in the range of 0.4 0.6). The
cement paste were cast into cylindrical PVC moulds (dia 4.9 mm and length 75 mm) and
compacted by vibration.

Fig. 15 Diffusion Cell

A typical set of result is shown in (Fig. 16).

_______________________________________
R S. Publication (http://rspublication.com), [email protected]

Page 172

International Journal of Advanced Scientific and Technical Research

Available online on http://www.rspublication.com/ijst/index.html

Issue 3 volume 6, Nov.-Dec. 2013

ISSN 2249-9954

_____________________________

Fig. 16 Chloride diffusion through OPC paste of w/c 0.4 at 25 0C

In the experiment, an initial delay (t0) was allowed to establish Cl- diffusion across the
thickness of the specimen disc. It was noted that there was a linear increase with time in the
Cl- concentration (C2) of the solution in compartment 2, while concentration (C1) in
compartment 1 was remaining effectively constant over the period of measurement. This
condition was noted as quasi steady state diffusion and it implies that the flux (J) is normal
to the diffusion direction and the activity (of Cl-) is effectively constant. Therefore the flux
can be given by [104]
(40)
2 -1
Where, D is the effective diffusivity of chloride ion through the disc in m s (assumed to be
independent of concentration), V is the volume of solution in compartment 2 in m3, A is the
cross-sectional area in m2, 1 is the thickness of the disc in m and C1 and C2, the solution
concentrations, are assumed to be equal to the surface activities of chloride ion in moles /m3.
The above work also included the values of diffusivity of Cl- at various temperatures in OPC
paste (w/c varying). The results of the data was given as Arrhenius plot, constructed by
means of linear regression analysis (Fig. 17) [104] and were found to be reasonably aggreable
[Fig. 16 and 17].

Fig. 17 Arrhenius Plots [104]

_______________________________________
R S. Publication (http://rspublication.com), [email protected]

Page 173

International Journal of Advanced Scientific and Technical Research

Available online on http://www.rspublication.com/ijst/index.html

Issue 3 volume 6, Nov.-Dec. 2013

ISSN 2249-9954

_____________________________
5.12.3.2 Method 2 :
Test method (Two Chamber Cell): A two chamber cell utilizes with concrete sample at
the division between two chambers is shown in (Fig. 18) [87]. Usually the concrete sample is
a disc of 100 mm dia and length 15 50 mm. The thickness of the disc will affect the
duration of test. However the thickness is important to avoid the influence of aggregate
interfaces. If the size of the aggregate is comparable to the thickness, there may exist a weak
transition zone around the aggregate, which may provide a faster path to the movement of the
chloride ions. To avoid this, the thickness must be sufficiently larger than the maximum
aggregate size. The cathode chamber may contain chloride ions and the anode chamber may
contain water or lime water. A voltage is then applied, and chloride ion concentration of the
downstream (anode chamber) is monitored and the change of chloride ion concentration (vs.
time) allows to find the diffusion coefficient. Role of applied voltage is important because it
controls the time required to perform the test e.g. a low voltage may avoid the heating of the
sample but may prolong the duration of test. A wide variety of voltages are reported in
literatures, e.g. 10 12 volt range, to avoid heating of sample, but these result in long test
duration[77, 105 109].

Fig.18. Typical chloride migration cell

6.0

Conclusion:

Different testing techniques for the study of diffusion of chloride ions which is the primary
cause for the deterioration and ultimate failure of rebar metals and concrete structures have
been briefly discussed above. Yet, most of the testing techniques have invariably used
various effective parameters assuming these as constants or negligible, as a result of which,
individually each test is answerable to one particular type of environmental condition. This
means if a multitude of factors are observed to be effecting chloride migration, then more
than one type of test procedure are to be conducted. Another poignant aspect is that in the
Ficks law there are different possibilitieswhich have been undermined, and these will come
up every time a new environmental parameter possesses threat to the concrete structure such
as the effect of fatigue (on rebar). A brief review of tests on chloride migration indicates that
the techniques involving electro migration have been given greater share, which is probably

_______________________________________
R S. Publication (http://rspublication.com), [email protected]

Page 174

International Journal of Advanced Scientific and Technical Research

Available online on http://www.rspublication.com/ijst/index.html

Issue 3 volume 6, Nov.-Dec. 2013

ISSN 2249-9954

_____________________________
due to the interest of rapid evaluation of the effect of chloride migration. But such data
cannot be true representative of the natural rate of migration of chloride ions, in spite of
arranging tests at lower range of voltage e.g. 1 3 volt. In this context it may be noted that
there always exist a self driving force inside the concrete cover which provides path for
ionic current between the anodic and cathodic portions of the rebar surface. However to track
this natural process is time consuming, beside the fact that such a test would involve year(s)
longtests which may be interrupted or distracted by different other evolving factors during the
period of experimentation.
Acknowledgement:
The authors express their thanks to the principal, Al-Kabir polytechnic. Mango,
Jamshedpur, India and Director, National Institute of Foundry and Forge Technology,
(NIFFT), Hatia, Ranchi, India for their support and encouragement
References:
1.
Anon., the Durability of Steel in Concrete, Part I. Mechanism of Protection and
Corrosion. Building Research Establishment Digest No. 263, UK, 1982.
2.
Hausman, D.A., Steel Corrosion in Concrete. Materials Protection, 6(11) (1967), 1922.
3.
Diamond, S., Chloride Concentrations in Concrete Pore Solutions Resulting From
Calcium and Sodium Chloride Admixtures. Cement, Concrete and Aggregates, 8(2)
(1986), 97-102.
4.
H. Ushiyama and S. Goto, Proc. 6th Intl. Cong. Chem. Cement, Moscow, 1974, Vol.
II-l, 331-337.
5.
S. Goto, M. Tsunetani, H. Yanagida and R. Kondo, J. Ceram. Soc. Japan, 87, (3), 127133 (1979).
6.
Tuutti, K. (1982). Corrosion of Steel in Concrete. Swedish Cement and Concrete
research Institute, 469.
7.
Stanish, K. and Thomas, M. (2003). The Use of Bulk Diffusion Tests to Establish
Time Dependent Concrete Chloride Diffusion Coefficients. Cement and Concrete
research, 33(1), 55-62.
8.
Thomas, M.D.A., Pantazopoulou, S.J. and Martin-Perez, B (1995). Service Life
Modelling of Reinforced Concrete Structures Exposed to Chlorides: A Literature
review. Department of Civil Engineering, University of Toronto, 45.
9.
Chini, A.R, Muszynski, L.C. and Hicks, J. (2003). Determination of Acceptance
Permeability Characteristics for Performance related Specifications for Portland
Cement Concrete. Final report No. BC 354-41, Florida Department of Transportation.
10.
Bamforth, P.B., Improving the Durability of Concrete Using Mineral Admixtures,
Concrete Durability in the Arabian Gulf, pp. 1-26, 1995.
11.
Tang, L. and Nilsson, L.-O., Chloride Diffusivity in High Strength Concrete, Nordic
Concrete Research, Vol. 11, pp. 162-170, 1992.
12.
Detwiler, R.J., Kjellsen, K.O., and Gjorv, O.E. Resistance to Chloride Intrusion of
Concrete Cured at Different Temperatures, ACI Materials Journal, Vol. 88, No. 1, pp.
19-24, 1991.
13.
Cao, Y., and Detwiler, R.J., Backscatter Electron Imaging of Cement Pastes Cured at
Elevated Temperatures, Cement and Concrete Research, Vol. 25, No. 3, pp. 627-638,
1995.
14.
Byfors, K., Chloride Binding in Cement Paste, Nordic Concrete Research, Vol. 5, pp.
27-38, 1986.

_______________________________________
R S. Publication (http://rspublication.com), [email protected]

Page 175

International Journal of Advanced Scientific and Technical Research

Available online on http://www.rspublication.com/ijst/index.html

Issue 3 volume 6, Nov.-Dec. 2013

ISSN 2249-9954

_____________________________
15.

16.

17.

18.
19.

20.
21.

22.
23.
24.
25.
26.

27.
28.
29.

30.
31.
32

33.

34.

Rasheeduzzafar, Dakhil, F.D., Bader, M.A. and Khan, M.M., Performance of

Corrosion Resisting Steels in Chloride Bearing Concrete, ACI Materials Journal, Vol.
89, No. 5, pp. 439-448, 1992.
Thomas, M.D.A., Pantazopoulou, S.J., and Martin-Perez, B., Service Life Modelling
of Reinforced Concrete Structures Exposed to Chlorides-A Literature Review,
prepared for the Ministry of Transportation, Ontario, at the University of Toronto,
1995.
Holden, W.R., Page, C.L., and Short, N.R., The Influence of Chlorides and Sulphates
on Durability, Corrosion of Reinforcement in Concrete Construction, (ed. A.P.
Crane), Ellis, Horwood, Chichester, pp. 143-150, 1983
Midgley, H.G., and Illston, J.M., The Penetration of Chlorides into Hardened Cement
Pastes, Cement and Concrete Research, Vol. 14, No. 4, pp. 546-558, 1984.
Hansson, C.M., and Sorenson, B., The Threshold Concentration of Chloride in
Concrete for the Initiation of Corrosion, Corrosion Rates of Steel in Concrete, ASTM
SP 1065, 99.3-16, 1990.
T.C. Powers, L.E. Copeland, H.M. Mann, Capillary continuity or discontinuity in
cement pastes, J. PCA Res. Dev. Lab. May (1959) 38-48.
M.R. Nokken, R.D. Hooton, Discontinuous Capillary Porosity in Concrete Does it
Exist? in: J. Weiss, K. Kovler, J. Marchand, S. Mindess (Eds.), Int. Symp. on
Advances in Concrete through Science and Engineering, Evanston, Illinois, Rilem,
2004.
G. Ye, Percolation of capillary pores in hardening cement pastes, Cem. Concr. Res.
35 (2005) 167-176.
A.M. Neville, Properties of Concrete, 4th Ed, Longman Ltd, 1995.
P. Grbl, H. Weigler, S. Karl, Beton, 2nd Ed, Ernst &Sohn, Berlin, 2001. (in
German).
L. Bertolini, B. Elsener, P. Pedeferri, R. Polder, Corrosion of steel in concrete,
WILEY VCH, Weinheim, 2004.
T.C. Powers, T.L. Brownyard, Studies of the Physical Properties of Hardened
Portland Cement Paste, Bulletin 22, Research Laboratories of the Portland cement
Association, 1948.
T.C. Powers, Physical Properties of Cement Paste, Proc. 4th Int. Symp. Chemistry of
Cement, Washington, D.C., 1960, pp. 577-613.
J.C. Maso (Ed.) Interfacial Transition Zone in Concrete, 1996, E & FN Spon, London.
Mammoloti L, Hansson C. M. Hope B. B. Corrosion Admixtures in concrete Part II:
Effect on Chloride Threshold Values for Corrosion of Steel in Synthetic Pore
Solutions. Cement and Concrete Research 1999; 29: 15831589p.
Kitowski C. J., Wheat H. G. Effect of Chlorides on Reinforcing Steel Exposed to
Simulated Concrete Solutions, Corrosion, NACE International 1990.
Ramirez C. W., Borgard B., Jones D., Heidersbach R. Laboratory Simulation of
Corrosion in Reinforced Concrete. Materials Performance 1990; 3339p.
Yuming Tang, Guodong Zhang and Yu Zuo. The Inhibition Effects of Several
Inhibitors on Rebar in Acidified Concrete Pore Solution. Construction and Building
Materials 2002; 28: 327332p.
Abosrra L., Youseffi M., Ashour A. F. Effectiveness of Calcium Nitrite in Retarding
Corrosion of Steel in Concrete, International Journa of Concrete Structures and
Materials 2011; 5(1): 65 73p.
L.-O. Nilsson, Hygroscopic moisture in concrete - drying, measurements & related
material properties, Report TVBM-1003, Division of Building Materials, Lund
Institute of Technology, 1980.

_______________________________________
R S. Publication (http://rspublication.com), [email protected]

Page 176

International Journal of Advanced Scientific and Technical Research

Available online on http://www.rspublication.com/ijst/index.html

Issue 3 volume 6, Nov.-Dec. 2013

ISSN 2249-9954

_____________________________
35.

36.
37.
38.
39.
40.
41.

42.

43.
44.
45.

46

47.
48.
49.
50.
51.

52.

53.
54.
55.
56.

S. Rostam, R.F.M. Bakker, A.W. Beeby, G. Hartl, D.V. Nieuwenburg, P. Schiessl, L.

Sentler, A.P.v. Vugt, Durable Concrete Structures, 2nd ed, Comit Euro-International
du Bton, Lausanne, Switzerland / Thomas Telford Services Ltd., 1989.
T.C. Powers, Structure and physical properties of hardened Portland cement paste, J.
Am. Ceram. Soc. 41 (1958) 1-6.
T.C. Powers, L.E. Copeland, J.C. Hayes, H.M. Mann, Permeability of Portland
Cement Paste, J. Amer. Concr. Ins. 51 (1954) 285-298.
D.A. Hausmann, Steel corrosion in concrete. How does it occur? Mater.
Protection 6 (1967) 19-23.
A. Bumel, Die Auswirkung von Betonzusatzmitteln auf das Korrosionsverhalten von
Stahl in Beton, Zement-Kalk-Gips 7 (1959) 294-305. (in German).
C.L. Page, Mechanism of corrosion protection in reinforced concrete marine
structures, Nature 258 (1975) 514-515.
C.L. Page, P. Lambert, P.R.W. Vassie, Investigations of reinforcement corrosion. 1.
The pore electrolyte phase in chloride-contaminated concrete, Mater. Struct. 24
(1991) 243-252.
P. Lambert, C.L. Page, P.R.W. Vassie, Investigations of reinforcement corrosion. 2.
Electrochemical monitoring of steel in chloride-contaminated concrete, Mater. Struct.
24 (1991) 351-358.
C.L. Page, Initiation of chloride-induced corrosion of steel in concrete: role of the
interfacial zone, Mater. Corros. 60 (2009) 586-592.
Dalton, John. 1808. A New System of Chemical Philosophy, Part I, Manchester:
Unlisted Publisher.
Dutrochet, Ren-J-H. 1827. Recherchessur L-endosmose et sur les
PhnomnesParticuliers aux Corps Vivants. Annales de Chimieet de Physique 35:
411437.
Dutrochet, Ren-J-H. 1827. Nouvelles Observations surLendosmoseetLexosmose,
et sur la Cause de ce Double Phnomne. Annales de Chimieet de Physique 35: 393
400.
Graham, Thomas. 1833. On the Law of Diffusion of Gases. Philosophical Magazine
2: 175204.
Graham, Thomas. 1850. On the Diffusion of Liquids. Philosophical Transactions of
the Royal Society 140: 146.
Ludwig, Carl F. W. 1852 and 1856. Lehrbuch der Physiologie des Menschen (2
Volumes), Heidelberg: University Press.
Fick, Adolf E. 1855. ber Diffusion.Annalen der Physike, Leipzig 94: 5986.
Einstein, Albert. 1905. Von der molekulrkinetischenTheorie der
WrmegefordeteBewegung von in ruhendenFlssigkeitensuspendiertenTeilchen.
Annalen der Physike17:549554.
Von Smoluchowski, Maryan. 1906. ZurkinetischenTheorie der
BrownschenMolekulrbewegung und der Suspensionen. Annalen der Physike21:
756780.
Wiener, Norbert. 1964. Selected Papers No 2. Cambridge, Mass.: Harvard University
Press.
Wax, N. (ed.). 1954. Selected Papers on Noise and Stochastic Processes. New York:
Dover Press.
Crank, J., The mathematics of Diffusion, 2nd ed., Clarendon Press, Oxford, 1975.
Hamilto. H. R., Boyd, Andrew J. and Vivas, E., Permeabilty of concrete
Comparison of conductivity and Diffusion Methods, UF Project no. 00026899,
University of Florida, 2007.

_______________________________________
R S. Publication (http://rspublication.com), [email protected]

Page 177

International Journal of Advanced Scientific and Technical Research

Available online on http://www.rspublication.com/ijst/index.html

Issue 3 volume 6, Nov.-Dec. 2013

ISSN 2249-9954

_____________________________
57.
58.

59.
60.
61.

62.

63.
64.

65.

66.

67.

68.

69.
70.

71.

72.

73.

74.

A. Atkinson and A. K. Nickerson, The diffusion of ions through water-saturated

cement, Journal of Materials Science 19 (1984)) 3068-3078.
Standard Method of Test for Resistance of Concrete to Chloride Ion Penetration,
(T259-80), American Association of State Highway and Transportation Officials,
Washington, D.C., U.S.A., 1980.
NT BUILD 443, 'Concrete, hardened: Accelerated chloride penetration', Nordtest,
Espoo, Finland, (1995).
Frederiksen, J. M., 'APM 302 - Danish test method for the chloride ingress into
concrete' (in Danish), Dansk Beton(2) (1992) 22-27.
Standard Method for Sampling and Testing for Chloride Ion in Concrete and Concrete
Raw Materials, (T260-94), American Association of State Highway and
Transportation Officials, Washington, D.C., U.S.A, 1994.
NT BUILD 492, 'Concrete, mortar and cement-based repair materials: Chloride
migration coefficient from non-steady state migration experiments', Nordtest, Espoo,
Finland, (1999).
Tang, L. and Nilsson, L.-O., Chloride Diffusivity in High Strength Concrete,
Nordic Concrete Research, Vol. 11, pp. 162-170, 1992.
Tang, L., 'Chloride diffusion coefficient of concrete and relevant test methods - The
state of the art and suggestions for future work', SP Report 1997:23, SP Swedish
National Testing and Research Institute, Boras, Sweden, (1997).
AASHTO, 'Standard method of test for rapid determination of the chloride
permeability of concrete', AASHTO T 277, American Association of State Highway
and Transportation Officials, Washington D.C., (1983).
NT BUILD 355, 'Concrete, mortar and cement-based repair materials: Chloride
diffusion coefficient from migration cell experiments', Ed. 2, Nordtest, Espoo,
Finland, (1997).
Standard Test Method for Electrical Indication of Chlorides Ability to Resist
Chloride (ASTM C1202-94) 1994 Annual Book of ASTM Standards V 04.02,
ASTM, Philadelphia, pg. 620-5.
Andrade, C. Calculation of Chloride Diffusion Coefficients in Concrete from Ionic
Migration Measurements Cement and Concrete Research, Vol. 23, No, 3, pp. 724742, 1993.
Zhang, M.H., and Gjorv, O.E., Permeability of High Strength Lightweight
Concrete, ACI Materials Journal, Vol. 88, No. 5, pp. 463-469, 1991.
Malek, R.I.A., and Roy, D.M., The Permeability of Chloride Ions in Fly Ash-Cement
Pastes, Mortars, and Concrete, MRS Symposium, Vol. 113, Materials Research
Society, Pittsburgh, pp. 291-300, 1996.
Roy, D.M., Hydration, Microstructure and Chloride Diffusion of Chloride Ions in
Hardened Cement Pastes, ACI SP-114, Vol. 2, American Concrete Institute, Detroit,
pp. 1265-1281, 1989.
Geiker, M., Thaulow, N. and Andersen, P.J., Assessment of Rapid Chloride Ion
Permeability Test of Concrete With and Without Mineral Admixtures, In Durability
of Building Materials, (ed. J.M. Baker, P.J. Nixon, A.J. Majumdar, H. Davis) E&FN
Spon, London, pp. 493-502, 1990.
Berke, N. S., and Hicks, M.C., Estimating the Life Cycle of Reinforced Concrete
Decks and Marine Piles Using Laboratory Diffusion and Corrosion Data, Corrosion
Forms and Control for Infrastructure, ASTM STP 1137, V. Chaker, ed., American
Society for Testing and Materials, Philadelphia, 1992.
Thomas, M.D.A., and Jones, M.R., A Critical Review of Service Life Modelling of
Concretes Exposed to Chlorides, Concrete in the Service of Mankind: Radical

_______________________________________
R S. Publication (http://rspublication.com), [email protected]

Page 178

International Journal of Advanced Scientific and Technical Research

Available online on http://www.rspublication.com/ijst/index.html

Issue 3 volume 6, Nov.-Dec. 2013

ISSN 2249-9954

_____________________________
75.

76.
77.
78.

79.
80.

81.
82.

83.
84.
85.

86.

87.
88.
89.
90.
91.
92.
93.
94.
95.
96.
97.
98.
99.
100.

Concrete Technology, (eds. R.K. Dhir and P.C. Hewlett), E.&F.N. Spon, London, pp.
723-736, 1996.
Otsuki, N., Nagataki, S., and Nakashita, K., Evaluation of AgNO3 Solution Spray
Method for Measurement of Chloride Penetration into Hardened Cementitious Matrix
Materials, ACI Materials Journal, Vol. 89, No. 6, pp. 587-592, 1992.
Monfore, G.E. The Electrical Resistivity of Concrete, Journal of the PCA Research
and Development Laboratories, pg. 35-48, May, 1968.
Streicher, P.E. and Alexander, M.G., A Chloride Conduction Test for Concrete,
Cement and Concrete Research, Vol. 25, No. 6, pp. 1284-1294, 1995.
Morris, W., Moreno, E.I. and Sagues, A. A., Practical Evaluation of Resistivity of
Concrete in Test Cylinders using a Wenner Array Probe, Cement and Concrete
Research, Vol. 26, No. 12, pp. 1779-1787, 1996.
Neville, A.M. Properties of Concrete- 3rd Edition, Longman Scientific and Technical,
Essex, England, 1981.
Andrade, C. Calculation of Chloride Diffusion Coefficients in Concrete From Ionic
Migration Measurements Cement and Concrete Research, Vol. 23, No, 3, pp. 724742, 1993.
Freeze, R.A., and Cherry, J.A. Groundwater, Prentice-Hall, Inc., New Jersey, 1979.
Valenta, O. Kinetics of Water Penetration into Concrete as an Important Factor of its
Deterioration and of Reinforcement Corrosion, RILEM International Symposium:
Durability of Concrete - 1969, Part 1, Prague, pp. A177-A189, 1969.
Hall, C. Water Sorptivity of Mortars and Concretes: A Review, Magazine of Concrete
Research, Vol. 41, No. 147, pp. 51-61, 1989.
Martys, N.S., and Ferraris, C.F., Capillary Transport in Mortars and Concrete,
Cement and Concrete Research, Vol. 27, No. 5, pp. 747-760, 1997.
Andrade, C. Calculation of Chloride Diffusion Coefficients in Concrete from Ionic
Migration Measurements Cement and Concrete Research, Vol. 23, No, 3, pp. 724742, 1993.
Andrade, C. and Sanjuan, M.A., Experimental Procedure for the Calculation of
Chloride Diffusion Coefficients in Concrete from Migration Tests, Advances in
Cement Research, Vol. 6, No. 23, pp. 127-134, 1994.
Xinying Lu, Application of the Nernst-Einstein Equation to Concrete, Cement and
Concrcte Research, Vol. 27, No. 2, pp. 293-302, 1997.
CL. Page, N.R. Short and A. El. Tarras, Cem. Concr.Res. 11,395 (1981).
G. Sergi, S.W. Yu, and C.L. Page, Mag. Concr. Res. 44, 63 (1992).
R.K. Dhir, M.R. Jones, and H.E.H. Ahmed, Mag. Concr. Res. 43, 37 (1991).
Kevin A. McDonald and Derek 0. Northwood, Cem. Concr.Res. 25, 1407 (1995).
P. Halamickova, R.J. Detwiler, D.P. Bentz, and E.J. Garboczi, Cem. Concr.Res. 25,
790 (1995).
P.J. Tumidajski, G.W. Chan, R.F. Feldman, G. Stratbdee, Cem. Concr.Res. 25, 1556
(1995).
S. Goto and D. M. Roy, Cem.Concr. Res. 11,75 I (1981).
V.T. Ngala, C.L. Page, L.J. Parrottand SW. Yu, Cem. Concr.Res. 25,819 (1995).
R.K. Dhir, M.R. Jones, H.E.H. Ahmed and A.M.G. Seneviratne, Mag. Concr. Res. 42,
177 (1990).
Tang Luping and Lam-Olof Nilsson, AC1 Mater. Jour. 89,49 (1992).
T. Sugiyama, T. W. Bremner, Y. Tsuji, Cem. Concr.Res. 26, 781 (1996).
C. Andrade, M.A. Sanjuan, A. Recuero, and 0. Rio, Cem. Concr.Res. 24, 1214
(1994).
Tiewei Zhang and Odd. E. Gjorv, Cem. Concr. Res. 24, 1534( 1994).

_______________________________________
R S. Publication (http://rspublication.com), [email protected]

Page 179

International Journal of Advanced Scientific and Technical Research

Available online on http://www.rspublication.com/ijst/index.html

Issue 3 volume 6, Nov.-Dec. 2013

ISSN 2249-9954

_____________________________
101.
102.
103.
104.
105.

106

107

108.

109.

R.F. Feldman, G.W. Chan, R.J. Brousseau, and P.J. Tumidajski, AC1 Mater. Jour.
91,246 (1994).
KC. Liam, S.K. Roy and D.O. Northwood, Mag. Concr. Res. 44,205 (1992).
O.E. Gjorv, Kefeng Tan, and Min-Hong Zhang, AC1 Mater.Jour. 91,447 (1994).
C.L. Page, N.R. Short and A. El Tarras, Diffusion of Chloride Ions in Hardened
Cement Pastes, Cement and Concrete Research. Vol. 11, pp. 395-406, 1981.
Andrade, C. and Sanjuan, M.A., Experimental Procedure for the Calculation of
Chloride Diffusion Coefficients in Concrete from Migration Tests, Advances in
Cement Research, Vol. 6, No. 23, pp. 127-134, 1994.
Delagrave, A., Marchaud, J., and Samson, E. Prediction of Diffusion Coefficients in
Cement-Based Materials on The Basis of Migration Experiments, Cement and
Concrete Research, Vol. 26, No. 12, pp. 1831-1842, 1996.
Detwiler, R.J., Kjellsen, K.O., and Gjorv, O.E. Resistance to Chloride Intrusion of
Concrete Cured at Different Temperatures, ACI Materials Journal, Vol. 88, No. 1,
pp. 19-24, 1991.
Jacobsen, S., Marchaud, J., and Boisvert, L., Effect of Cracking and Healing on
Chloride Transport in OPC Concrete, Cement and Concrete Research, Vol. 26, No.
6, pp. 869-881, 1996.
McGrath., P. and Hooton, R.D., Influence of Voltage on Chloride Diffusion
Coefficients from Chloride Migration Tests, Cement and Concrete Research, Vol.
26, No. 8, pp. 1239-1244, 1996.

_______________________________________
R S. Publication (http://rspublication.com), [email protected]

Page 180