Scribd
Upload
2K views

Conjugate Beam Method

The conjugate beam method can be used to determine beam deflections and slopes. It involves drawing a conjugate beam that has the same length as the real beam but different supports. The conjugate beam is loaded with the bending moment diagram of the real beam. Using static equilibrium equations, the shear and moment at points on the conjugate beam can be determined, which equal the slope and deflection, respectively, at corresponding points on the real beam. Sample problems demonstrate how to use this method to analyze statically determinate and indeterminate beams.

Uploaded by

ofreneo_joshua4437
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
2K views

Conjugate Beam Method

The conjugate beam method can be used to determine beam deflections and slopes. It involves drawing a conjugate beam that has the same length as the real beam but different supports. The conjugate beam is loaded with the bending moment diagram of the real beam. Using static equilibrium equations, the shear and moment at points on the conjugate beam can be determined, which equal the slope and deflection, respectively, at corresponding points on the real beam. Sample problems demonstrate how to use this method to analyze statically determinate and indeterminate beams.

Uploaded by

ofreneo_joshua4437
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 24

Beam Deflections: Geometric

Methods
Conjugate Beam Method

Conjugate Beam Method

The conjugate-beam method was developed by H.


Mller-Breslau in1865.
Essentially, it requires the same amount of
computation as the moment-area theorems to
determine a beams slope or deflection;
However, this method relies only on the principles of
statics, and hence its application will be more
familiar.

A conjugate beam corresponding to a real beam is a


fictitious beam of the same length as the real beam, but
it is externally supported and internally connected such
that if the conjugate beam is loaded with the M=EI
diagram of the real beam, the shear and bending
moment at any point on the conjugate beam are equal,
respectively, to the slope and deflection at the
corresponding point on the real beam.

Here the shear V compares with the slope , the


moment M compares with the displacement ,
and the external load w compares with the M/EI
diagram.
To make use of this comparison we will now
consider a beam having the same length as the
real beam, but referred to here as the conjugate
beam,

The conjugate beam is loaded with the M/EI


diagram derived from the load w on the real beam.
From the above comparisons, we can state two
theorems related to the conjugate beam, namely,
Theorem 1: The slope at a point in the real beam is numerically equal to the
shear at the corresponding point in the conjugate beam.
Theorem 2: The displacement of a point in the real beam is numerically equal to
the moment at the corresponding point in the conjugate beam.

Conjugate Beam Supports


When drawing the conjugate beam it is important
that the shear and moment developed at the
supports of the conjugate beam account for the
corresponding slope and displacement of the real
beam at its supports, a consequence of Theorems
1 and 2. For example, as shown in Table 82, a pin
or roller support at the end of the real beam
provides zero displacement, but the beam has a
nonzero slope.

Consequently, from
Theorems 1 and 2, the
conjugate beam must
be supported by a pin
or roller, since this
support has zero
moment but has a
shear or end reaction.
When the real beam is
fixed supported (3),
both the slope and
displacement at the
support are zero. Here
the conjugate beam
has a free end, since at
this end there is zero
shear and zero
moment.
Corresponding real and
conjugate-beam supports
for other cases are listed in
the table.

Note that, as a rule,


neglecting axial
force, statically
determinate real
beams have
statically
determinate
conjugate beams;
and statically
indeterminate real
beams, as in the
last case in Fig. 8
24, become
unstable conjugate
beams.
Although this occurs, the
M/EI loading will provide
the necessary equilibrium
to hold the conjugate beam
stable.

Types of Supports

Procedure for Analysis


The following procedure provides a method that may be used to
determine the displacement and slope at a point on the elastic
curve of a beam using the conjugate-beam method.
Conjugate Beam
Draw the conjugate beam for the real beam. This beam has the
same length as the real beam and has corresponding supports as
listed in Table 82.
In general, if the real support allows a slope, the conjugate
support must develop a shear; and if the real support allows a
displacement, the conjugate support must develop a moment.
The conjugate beam is loaded with the real beams M/EI diagram.
This loading is assumed to be distributed over the conjugate
beam and is directed upward when M/EI is positive and
downward when M/EI is negative. In other words, the loading
always acts away from the beam.

Equilibrium
Using the equations of equilibrium, determine the
reactions at the conjugate beams supports.
Section the conjugate beam at the point where the
slope and displacement of the real beam are to be
determined. At the section show the unknown
shear and moment acting in their positive sense.

The conjugates of some common types of (real) beams are depicted


in Fig. 6.13. As Fig. 6.13(a)(e) indicates, the conjugate beams
corresponding to statically determinate real beams are always
statically determinate, whereas statically indeterminate beams have
unstable conjugate beams, as shown in Fig. 6.13(f )(h). However,
since these unstable conjugate beams will be loaded with the M=EI
diagrams of statically indeterminate real beams, which are selfbalancing, the unstable conjugate beams will be in equilibrium. As
the last two examples in Fig. 6.13 illustrate, statically unstable real
beams have statically indeterminate conjugate beams.

Sign Convention
If the positive ordinates of the M=EI diagram are applied to the
conjugate beam as upward loads (in the positive y direction) and
vice versa, then a positive shear in the conjugate beam denotes a
positive (counterclockwise) slope of the real beam with respect to
the undeformed axis of the real beam; also, a positive bending
moment in the conjugate beam denotes a positive (upward or in the
positive y direction) deflection of the real beam with respect to the
undeformed axis of the real beam and vice versa.

Sample Problems
Determine the slopes and deflections at points B
and C of the cantilever beam shown in Fig. 6.14(a)
by the conjugate beam method.

Determine the slope and deflection at point B of


the beam shown in Fig. 6.15(a) by the conjugatebeam method.

Use the conjugate-beam method to determine the


slopes at ends A and D and the deflections at
points B and C of the beam shown in Fig. 6.16(a).

Determine the maximum deflection for the beam


shown in Fig. 6.17(a) by the conjugate-beam
method.

Determine the slope at point A and the deflection


at point C of the beam shown in Fig. 6.18(a) by the
conjugate-beam method.

Use the conjugate-beam method to determine the


deflection at point C of the beam shown in Fig.
6.19(a).

References
Structural Analysis (Fourth Edition) - by Aslam
Kassimali
Structural Analysis SI EDITION (Fourth
Edition) - by Aslam Kassimali
Structural Analysis (Eight Edition) by R.C.
Hibbeler

You might also like