Scribd
Upload
52 views

Eeng 432 Microwave Theory and Design Lab: Marks Obtained Total Marks

This document provides instructions for Lab 02 of the EENG 432 Microwave Theory and Design lab. The objective is to study the voltage-current (V-I) characteristics of a Gunn diode. Students are instructed to connect a Gunn diode power supply, voltmeter, and ammeter according to the provided diagram and record voltage and current readings while varying the supply voltage. They will then plot the V-I curve and determine the threshold voltage corresponding to maximum current. Lab reports must be submitted individually before the next session, and makeup work will not be allowed without a valid reason.

Uploaded by

Sohail Khilji
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
52 views

Eeng 432 Microwave Theory and Design Lab: Marks Obtained Total Marks

This document provides instructions for Lab 02 of the EENG 432 Microwave Theory and Design lab. The objective is to study the voltage-current (V-I) characteristics of a Gunn diode. Students are instructed to connect a Gunn diode power supply, voltmeter, and ammeter according to the provided diagram and record voltage and current readings while varying the supply voltage. They will then plot the V-I curve and determine the threshold voltage corresponding to maximum current. Lab reports must be submitted individually before the next session, and makeup work will not be allowed without a valid reason.

Uploaded by

Sohail Khilji
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

EENG 432 MICROWAVE THEORY AND DESIGN LAB

LAB 02

STUDENT NUMBER
STUDENT NAME
DATE

Marks Obtained

Total Marks

Key Notes:

Lab reports should be submitted before the commencement of next lab session.
Lab reports should be submitted separately i.e. not in groups.
There will be no make up for the lab, unless you have any genuine problem.

EENG 432 MICROWAVE THEORY AND DESIGN LAB


OBJECTIVE:
To study the V-I characteristics if GUNN Diode.
EQUIPMENT REQUIRED:

Gunn Power Supply


Voltmeter
Ammeter
Connecting Cables

THEORY:
GUNN Diodes (Transferred Electron Devices):
Gunn diodes are negative resistance devices which are normally used as low power
oscillator at microwave frequencies in transmitter and also as local oscillator in receiver front
ends. J B Gunn (1963) discovered microwave oscillation in Gallium arsenide (GaAs), Indium
phosphide (InP) and cadmium telluride (CdTe). These are semiconductors having a closely
spaced energy valley in the conduction band as shown in Fig. 1 for GaAs. When a dc voltage is
applied across the material, an electric field is established across it. At low E-field in the
material, most of the electrons will be located in the lower energy central valley . At higher Efield, most of the electrons will be transferred in to the high-energy satellite L and X valleys
where the effective electron mass is larger and hence electron mobility is lower than that in the
low energy valley. Since the conductivity is directly proportional to the mobility, the
conductivity and hence the current decreases with an increase in E-field or voltage in an
intermediate range, beyond a threshold value Vth as shown in Fig. 2. This is called the transferred
electron effect and the device is also called Transfer Electron Device (TED) or Gunn diode.
Thus the material behaves as negative resistance device over a range of applied voltages and can
be used in microwave oscillators.

Figure 1: Multi-valley conduction band energies of GaAs

The basic structure of a Gunn diode is shown in Fig. 5.2 (a), which is of n-type GaAs
semiconductor with regions of high doping (n+). Although there is no junction this is called a
diode with reference to the positive end (anode) and negative end (cathode) of the dc voltage
applied across the device. If voltage or an electric field at low level is applied to the GaAs,
initially the current will increase with a rise in the voltage. When the diode voltage exceeds a
certain threshold value, Vth a high electric field (3.2 KV/m for GaAs) is produced across the
active region and electrons are excited from their initial lower valley to the higher valley, where
they become virtually immobile. If the rate at which electrons are transferred is very high, the
current will decrease with increase in voltage, resulting in equivalent negative resistance effect.
Since GaAs is a poor conductor, considerable heat is generated in the diode. The diode will be
bonded into a heat sink (Cu-stud).

Figure 2: V-I Characteristics of Gunn Diode


PROCEDURE:

1. Set the components and equipment as shown in the Figure below.


2. Keep the control knob of Gunn Power Supply as below:
Meter Switch - OFF
Gunn bias knob - Fully anticlockwise
Pin bias knob - Fully anticlockwise
Pin Mod frequency - Any position
3. Turn the meter switch of Gunn power supply to voltage position.
4. Measure the Gunn diode current corresponding to the various voltage controlled by Gunn
bias knob through the panel meter and meter switch. Do not exceed the bias voltage
above 10 volts.
5. Plot the voltage and current readings.
6. Measure the threshold voltage which corresponds to maximum current.

CONNECTION DIAGRAM:

Voltmeter

Gunn Supply

Ammeter

OBSERVATIONS AND CALCULATIONS:


Voltage (V)

Current (I)

The threshold Voltage corresponds to maximum current is: ____________________

CONCLUSION:

You might also like