MAC protocols

Lecturer: Dmitri A. Moltchanov

E-mail: [email protected]
http://www.cs.tut.fi/kurssit/TLT-2616/

Ad hoc networks

D.Moltchanov, TUT, 2011

OUTLINE:
Problems for MAC to deal with;
Design goals;
Classification of MAC protocols
Contention-based protocols
Contention-based with reservation mechanism
Contention-based with scheduling mechanism
MAC protocols for directional antennas
Power control MAC protocols

Lecture: MAC protocols

Ad hoc networks

D.Moltchanov, TUT, 2011

1. Problems for MAC to deal with

Aim of MAC: provide fair access to shared broadcast radio channel.

Issues to deal with:

Bandwidth efficiency:
must be maximized.
Real-time traffic support:
should be provided.
Synchronization:
sometimes needed, e.g. TDMA.
Shared broadcast medium:
collisions must be avoided/minimized.
Lack of central coordination:
fully distributed MAC design.

Lecture: MAC protocols

Ad hoc networks

D.Moltchanov, TUT, 2011

Hidden terminal problem:

collisions inefficient bandwidth utilization.

packets

hidden terminal

collision

receiver

packets

sender

Figure 1: Illustration of the hidden terminal problems.

Lecture: MAC protocols

Ad hoc networks

D.Moltchanov, TUT, 2011

Exposed terminal problem:

inability to transmit inefficient bandwidth utilization.

packets

receiver

packets

exposed terminal

sender

receiver

Figure 2: Illustration of the exposed terminal problem.

Lecture: MAC protocols

Ad hoc networks

D.Moltchanov, TUT, 2011

Mobility of nodes:
loss of connectivity;
network partitioning;
bit errors.

t
t+Delta(t)
Figure 3: Network partitioning is one of the biggest problem to deal with at MAC sublayer.

Lecture: MAC protocols

Ad hoc networks

D.Moltchanov, TUT, 2011

2. Design goals
What we want from MAC protocol:
operation of the protocol should be distributed;
should support real-time traffic;
the access delay must be minimized;
available bandwidth must be utilized efficiently;
fair bandwidth allocation to competing nodes;
control overhead must be minimized;
the effects of hidden/exposed terminals must be minimized;
must be scalable;
should minimize power consumption;
should provide synchronization between nodes.

Lecture: MAC protocols

Ad hoc networks

D.Moltchanov, TUT, 2011

3. Classification of MAC protocols

MAC protocol for ad-hoc networks must be classified into:
Contention-based protocols without reservation/scheduling:
no reservation of the bandwidth is made;
guarantees are not possible.
Contention-based protocols with reservation mechanisms:
bandwidth for transmission is reserved in advance.
guarantees are possible.
Contention-based protocols with scheduling mechanisms:
distributed scheduling between nodes is used.
guarantees are possible.
Protocols that do not fall to any of these categories:
implement several features of different protocol groups or
use completely different approach

Lecture: MAC protocols

Ad hoc networks

D.Moltchanov, TUT, 2011

MAC protocols for ad-hoc networks

Contention-based

sender initiated

Reservation

Scheduling
- DPS;
- DWOP;
- DLPS.

receiver initiated

Other
- MMAC;
- MCSMA;
- PCM;
- RBAR.

- RI-BTMA;
- MACA-BI;
- MARCH.
synchronous
single channel
- MACAW;
- FAMA.

multiple channel
- BTMA;
- DBTMA;
- ICSMA.

Lecture: MAC protocols

- D-PRMA;
- CATA;
- HRMA;
- SRMA/PA;
- FPRP.

asynchronous
- MACA/PR;
- RTMAC.

Ad hoc networks

D.Moltchanov, TUT, 2011

4. Contention based protocols w/o reservation/scheduling

The basic idea: do your best to not cause a collision.

4.1. MACA protocol

MACA is based on CSMA/CA that operates as follows:
the sender sense the channel for the carrier signal;
if the carrier is present it retries to sense the channel after some time (exp. back-off);
if not, the sender transmits a packet.
The following shortcomings are inherent to CSMA/CA:
: hidden terminal problem leading to frequent collisions;
: exposed terminal problem leading to worse bandwidth utilization.
To avoid it:
virtual carrier sensing;
RTS-CTS handshake before transmission.

Lecture: MAC protocols

10

Ad hoc networks

D.Moltchanov, TUT, 2011

Neighbor

Sender

RTS

Receiver

Neighbor

RTS

CTS

Data

CTS

Data

ACK

ACK

Figure 4: Packet transmission in MACA.

Lecture: MAC protocols

11

Ad hoc networks

D.Moltchanov, TUT, 2011

NEIGHBOR
BACK-OFF RTS

DATA

SENDER
CTS

ACK

REVEIVER
BACK-OFF
NAV FROM RTS

NEIGHBOR

NAV FROM CTS

NAV FROM DATA

Figure 5: Usage of virtual carrier sensing.

NAV: network allocation vector implementation of virtual carrier sensing.

Lecture: MAC protocols

12

Ad hoc networks

D.Moltchanov, TUT, 2011

If the transmission fails:

contention window: CW2 (multiplicative increase, immediate decrease);
retransmission.

31

initial

63

1st

127

2nd

255

3rd

511
1023 slots

4th
5th

Figure 6: Evolution of the contention window with increasing of transmission attempts.

Lecture: MAC protocols

13

Ad hoc networks

D.Moltchanov, TUT, 2011

Problem 1 of MACA: starvation of flows:

both S1 and S2 have the high volume of traffic, S1 seizes the channel first;
packets transmitted by S2 get collided and it doubles CW (CW = 2CW );
the probability that the node S2 seizes the channel is decreasing.

S1

S2

Figure 7: Starvation of the flow from S2.

Solution:
the packet header contains the field set to the current back-off value of the transmitting node;
a node receiving this packet copies this value to its back-off counter (fairness);
CW = CWmin after every successful transmission.

Lecture: MAC protocols

14

Ad hoc networks

D.Moltchanov, TUT, 2011

Problem 2 of MACA: fast adjustment of CW:

when a node successfully transmits a packet;
when a collisions is detected by a node.
S1

S2

BACKOFF
CW=511
S1
RECEIVER
BACKOFF

RTS

CTS

DATA

ACK

CW=511

BACKOFF
CW=CW min

S2

Figure 8: Rapid adjustments of the CW.

Solution: multiplicative increase when collision, linear decrease when success.

Lecture: MAC protocols

15

Ad hoc networks

D.Moltchanov, TUT, 2011

Problem 3 of MACA: an exposed node is free to transmit.

ongoing transmission S1-R1;
node S2 hears RTS but not CTS (exposed node);
S2 initiates transfer to R2;
DATA from S1 and CTS from R2 may collide, CW unnecessary increases at S2.

RTS
R1

DATA

CTS

S1

DATA

CTS
R2

S2
RTS

RTS

Figure 9: Problems with exposed node.

Solution: use of small data sending packet (DS) to update information.

Lecture: MAC protocols

16

Ad hoc networks

D.Moltchanov, TUT, 2011

4.2. Busy tone multiple access protocol (BTMA)

Multichannel protocol where the channel is separated into:
control channel: used for data transmission;
data channel: used for busy tone transmission.
BTMA works as follows:
a node senses the control channel to check whether the busy tone is active;
if not, it turns on the busy tone signal and starts data transmission;
if yes, a node waits for a random period of time and repeats the procedure;
any node that senses the carrier on the incoming data channel also transmits a busy tone.
There are following advantages are shortcoming of the BTMA:
+: simple enough;
+: probability of collision is extremely low;
: bandwidth utilization is low (nodes are blocked in two-hop neighborhood).

Lecture: MAC protocols

17

Ad hoc networks

D.Moltchanov, TUT, 2011

4.3. MACA by invitation (MACA-BI)

Receiver-initiated MAC protocol providing the following extension to MACA:
MACA: RTS-CTS-DATA-ACK;
MACA-BI eliminates the need for CTS using the receivers ready-to-receive (RTR) packet.
Sender

Receiver
RTR

Neighbor
RTR

DATA

Figure 10: Transmission in MACA-BI.

needs information about the traffic at neighboring nodes;
this information is included into DATA packets.

Lecture: MAC protocols

18

Ad hoc networks

D.Moltchanov, TUT, 2011

4.4. Media access with reduced handshake (MARCH)

RTS packet is used only for the first DATA packet of the stream:
nodes know about packet arrival at neighboring node listening to CTS signals;
to relay packet, it sends a CTS packet to the concerned node.
node 1

node 2

node 3

node 4

RTS
CTS

CTS

DATA
CTS

CTS

DATA
CTS
Chain relaying

DATA

Figure 11: Relaying using the MARCH.

Lecture: MAC protocols

19

Ad hoc networks

D.Moltchanov, TUT, 2011

The CTS packet in MARCH carries the following information:

the MAC address of the sender and the receiver node;
route identification number Rid to distinguish between routes.
Route 1: A-B-C-D-E
Route 2: X-C-Y

MARCH is characterized by the following advantages and shortcomings:

+: very high throughput;
+: very low control overhead;
: access to routing information is required cross-layering!

Lecture: MAC protocols

20

Ad hoc networks

D.Moltchanov, TUT, 2011

5. Contention-based protocols with reservations

Use bandwidth reservation techniques:
contention occurs here only at resource reservation phase;
once bandwidth is reserved a node gets an exclusive access to the media.

5.1. Distributed packet reservation multiple access protocol (D-PRMA)

D-PRMA is a TDMA based scheme where the channel is divided into frames.
Frame length
Slot 1

Slot 2

Minislot 1

Minislot 2

RTS/BI

CTS/BI

...

Slot n

Minislot m

DATA

Figure 12: Frame structure in D-PRMA.

Lecture: MAC protocols

21

Ad hoc networks

D.Moltchanov, TUT, 2011

Slot reservation and overcoming the hidden terminal problem:

Request to send / busy indication (RTS/BI) and clear to send / busy indication (CTS/BI).
The protocol operates as follows:
nodes having a packet for transmission contend in the first minislot of each slot;
the remaining (m 1) minislots in the slot are granted to the node that wins the contention;
the same slot in subsequent frames is reserved for the this terminal, until it ends transmission;
if no node wins the first minislot, the remaining minislots subsequently used for contention;
within a reserved slot communication is performed using TDD or FDD.
Slot reservation mechanism performs as follows:
a certain period in the beginning of each minislot is reserved for carrier-sensing;
if a nodes detects a channel to be idle, it sends a RTS packet to destination using RTS/BI;
receiver answers with CTS packets in the CTS/BI field of the same minislot;
the sender upon receiving CTS, gets a reservation for current slot (all minislots).

Lecture: MAC protocols

22

Ad hoc networks

D.Moltchanov, TUT, 2011

To prioritize the voice traffic:

Rule 1:
voice nodes traffic are allowed to start contention from minislot 1 with probability 1.
data nodes start contention from minislot 1 with probability < 1;
for the remaining (m 1) minislots all nodes contend with probability 1.
Rule 2:
if the node winning the contention is the data node, only the current slot is reserved;
if the node winning the contention is the voice node, subsequent slots are also reserved.
To make it real the following requirements must be satisfied:
Requirements for nodes other than a winning one:
hidden and exposed terminals should be avoided;
no contention:
no contention in remaining minislots;
no contention in the subsequent slots.

Lecture: MAC protocols

23

Ad hoc networks

D.Moltchanov, TUT, 2011

Requirement 1: (no contention in other minislots)

Hidden terminal problem:
RTS packet do not suffer a collision due to carrier sensing (winning node transmits);
a node hearing the CTS is not allowed to transmit in the remaining period of the slot.
Exposed terminal problem:
A node hearing the RTS but not CTS is allowed to transmit.
Requirement 2: (no contention in other slots)
the receiver and sender transmit a BI signal in minislot 1 of the reserved slot;
when any node hears BI signal it does not contend in this slot;
when the transmission is completed both sides stops transmission of BI signal.
Advantages and shortcomings:
+: D-PRMA is best suited for voice applications;
: requires synchronization (TDMA).

Lecture: MAC protocols

24

Ad hoc networks

D.Moltchanov, TUT, 2011

6. Contention-based protocols with scheduling mechanisms

Aim is on transmission scheduling at nodes considering metrics:
delay targets of packets;
traffic load at nodes;
remaining battery power at nodes, etc.

6.1. Distributed priority scheduling (DPS)

This protocols is primarily based on IEEE 802.11 DCF using RTS-CTS-DATA-ACK mechanism.
The communication is as follows:
RTS packet transmitted by a node carries priority index of the packet (delay, etc.);
the receiver responds with CTS containing the priority tag and source ID copied from RTS;
neighbors retrieve this information from RTS and CTS and make entry in scheduling tables;
source sends DATA and receiver responds with ACK;
after DATA and ACK is transmitted neighbor updates their scheduling tables.

Lecture: MAC protocols

25

Ad hoc networks

D.Moltchanov, TUT, 2011

RTS

DATA

Node 3 (neighbor to node 1)

RTS

CTS

DATA

ACK

Node 1

RTS

CTS

DATA

ACK

Node 2
CTS

ACK

Node 4 (neighbor to node 2)

S

Figure 13: Packet exchange and scheduling tables update in DPS.

Lecture: MAC protocols

26

Ad hoc networks

D.Moltchanov, TUT, 2011

7. MAC protocols for directional antennas

The following advantages can be achieved using the directional antennas:
reduced signal interference;
increase in system throughput;
improved channel reuse.

7.1. MACA for directional antennas

For this protocol the following assumptions are used:
each node has only one radio transceiver;
transceiver is equipped with M directional antennas;
each antenna covers angle 2/M ;
transmissions by adjacent antennas never overlap;
MAC layer is able to switch antennas individually or all antennas together.
Packet transmission is made using RTS-CTS-DATA-ACK.

Lecture: MAC protocols

27

Ad hoc networks

D.Moltchanov, TUT, 2011

S
RT S
CT ATA
D

Figure 14: Packet transmission using directional antennas.

The main problem is to determine the direction of each other:
idle node listens on all antennas;
the sender transmits RTS using omnidirectional transmission;
the receiver responses with CTS using omnidirectional transmission;
both determines the antennas with the highest quality of the signal and switch them up.

Lecture: MAC protocols

28

Ad hoc networks

D.Moltchanov, TUT, 2011

7.2. Directional busy tone based MAC protocol

The major features of this protocol are as follows:
it uses directional antenna consisting of N elements;
for broadcast all elements are used;
for unicast only one element is used;
when a node is idle all elements sensing the channel;
while receiving only one element receives the signal.
It operates as follows:
a node senses the channel for presence of receiver busy tone (BTr );
if BTt is not active, it sends RTS on all antennas elements;
the receiver receives RTS and makes sure that BTt is not present;
then, the receiver transmits CTS directionally to the sender and turn on the BTr ;
the sender turns on the BTt and sends the DATA packet.

Lecture: MAC protocols

29

Ad hoc networks

D.Moltchanov, TUT, 2011

8. Power control MAC protocol

This protocol allows to vary a transmission range of nodes on a per-packet basis.
There are two modes of operation:
BASIC protocol;
PCM protocol.
The BASIC protocol operates as follows:
RTS and CTS packets are transmitted using the maximum power pmax ;
RTS-CTS packets are used to decide necessary transmission power for DATA and ACK packets:
Method 1: The receiver send CTS with estimated transmitted level pd < pmax ;
Method 2: CTS is sent back using pmax and the source calculates pd based on pmax :
pmax
pd =
Rxth c,
pr

(1)

where
Rxth is the minimum required power and c is a constant
pr is the received signal strength.

Lecture: MAC protocols

30

Ad hoc networks

D.Moltchanov, TUT, 2011

Node C sense carrier of RTS but not CTS;
Node D sense carrier of CTS but not RTS;
D

se
ns
ing

ACK

RT
S

DATA

RTS

S
CT

Both waits for extended IFS:

- C packet may collide with ACK;
- D packet may collide with DATA.

ing
s
n
se

Solution: increase power to pmax during

DATA packet transmission:

CTS

pmax
pd

DATA packet

Figure 15: The major problem associated with BASIC protocol.

Lecture: MAC protocols

31