Scribd
Upload
207 views

Consolidation Test - Lab Manual

1. The document describes the procedure for conducting a consolidation test, also known as an oedometer test, which is used to determine the consolidation properties of fine-grained soils. 2. The test subjects an undisturbed soil sample to incremental loads in a consolidometer device, and measures the amount of compression over time. 3. Key properties that can be determined include the coefficient of consolidation, compression index, coefficient of compressibility, coefficient of permeability, and the relationship between soil pressure and void ratio. This information is useful for predicting settlement of structures built on fine-grained soils.

Uploaded by

Amira Syazana
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
207 views

Consolidation Test - Lab Manual

1. The document describes the procedure for conducting a consolidation test, also known as an oedometer test, which is used to determine the consolidation properties of fine-grained soils. 2. The test subjects an undisturbed soil sample to incremental loads in a consolidometer device, and measures the amount of compression over time. 3. Key properties that can be determined include the coefficient of consolidation, compression index, coefficient of compressibility, coefficient of permeability, and the relationship between soil pressure and void ratio. This information is useful for predicting settlement of structures built on fine-grained soils.

Uploaded by

Amira Syazana
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

INDIAN INSTITUTE OF TECHNOLOGY GANDHINAGAR

Department of Civil Engineering


Soil Mechanics Laboratory
CONSOLIDATION TEST- (OEDOMETER TEST)
(IS 2720-PART-15-1986) Reaffirmed-2002
THEORY:
When a compressive load is applied to soil mass, a decrease in its volume takes place, the decrease in volume of soil
mass under stress is known as compression and the property of soil mass pertaining to its tendency to decrease in volume
under pressure is known as compressibility. In a saturated soil mass having its void filled with incompressible water, decrease
in volume or compression can take place when water is expelled out of the voids. Such a compression resulting from a long
time static load and the consequent escape of pore water is termed as consolidation.Then the load is applied on the saturated
soil mass, the entire load is carried by pore water in the beginning. As the water begins escaping from the voids, the
hydrostatic pressure in water gets gradually dissipated and the load is shifted to the soil particles which increases effective
stress on them, as a result the soil mass decrease in volume. The rate of escape of water depends on the permeability of the
soil.

NEED AND SCOPE:


The test is conducted to determine the settlement due to primary consolidation.
a.

Rate of consolidation under normal load.

b.

Degree of consolidation at any time.

c.

Pressure-void ratio relationship.

d.

Coefficient of consolidation at various pressures.

e.

Compression index.

The above information can be used to predict the time rate and extent of settlement of structures founded on fine-grained
soils. It is also helpful in analyzing the stress history of soil.

APPARATUS REQUIRED:
1.

Consolidometer consisting essentially;


a) A ring of diameter = 60mm and height = 20mm,
b) Two porous plates or stones of silicon carbide, aluminum oxide or porous metal.
c) Guide ring.
d) Outer ring.
e) Water jacket with base.
f) Pressure pad.
g) Rubber basket.

2.

Loading device consisting of frame, lever system, loading yoke dial gauge fixing device and weights.

3.

Dial gauge (accuracy of 0.002 mm), Thermostatically controlled oven, Stopwatch, sample extractor, balance, soil
trimming tools, spatula, filter papers, sample containers.

IIT Gandhinagar, Soil Mechanics Lab

Page1

INDIAN INSTITUTE OF TECHNOLOGY GANDHINAGAR


Department of Civil Engineering
Soil Mechanics Laboratory

SAMPLE PREPARATION:
1.

Undisturbed Sample:

From the sample tube, eject the sample into the consolidation ring. The sample should project about one cm from outer ring.
Trim the sample smooth and flush with top and bottom of the ring by using wire saw. Clean the ring from outside and
keep it ready for weighing.
2.

Remoldedsample:
a.

Choose the density and water content at which sample has to be compacted from the moisture-density curve, and
calculate the quantity of soil and water required to mix and compact.

b.

Compact the specimen in compaction mould in three layers using the standard rammers.

c.

Eject the specimen from the mould using the sample extractor.

PROCEDURE:
1.

Saturate two porous stones either by boiling in distilled water about 15 minute or by keeping them submerged in the
distilled water for 4 to 8 hrs. Fittings of the Consolidometer which is to be enclosed shall be moistened.

2.

Assemble the Consolidometer, with the soil specimen and porous stones at top and bottom of specimen, and providing a
filter paper between the soil specimen and porous stone.

3.

Position the pressure pad centrally on the top porous stone. Mount the mould assembly on the loading frame, and center
it such that the load applied is axial. Make sure that the porous stone and pressure pad are not touching the walls of
mould on their sides.

4.

Position the dial gauge to measure the vertical compression of the specimen. The dial gauge holder should be set so that
the dial gauge is in the beginning of its releases run, and also allowing sufficient margin for the swelling of the soil, if
any.

5.

Fill the mould with water and apply an initial load to the assembly. The magnitude of this load should be chosen by trial,
such that there is no swelling. It should be not less than 50 g/cm2 for ordinary soils & 25 g/cm2 for very soft soils. The
load should be allowed to stand until there is no change in dial gauge readings for two consecutive hours or for a
maximum of 24 hours.

6.

Note the final dial reading under the initial load. Apply first load of intensity 0.1 kg/cm 2(Approx.) and start the stop
watch simultaneously. Record the dial gauge readings at various time intervals. The dial gauge readings are taken until
90% consolidation is reached. Primary consolidation is gradually reached within 24 hrs.

7.

At the end of the period, specified above take the dial reading and time reading. Double the load intensity and take the
dial readings at various time intervals. Repeat this procedure for successive load increments. The usual loading intensity
is as follows (Approx.): 0.1, 0.2, 0.5, 1, 2, 4 and 8 kg/cm2.

8.

After the last loading is completed, reduce the load to of the value of the last load and allow it to stand for 24 hrs.
Reduce the load further in steps of the previous intensity till an intensity of 0.1 kg/cm2 is reached. Take the final
reading of the dial gauge.

9.

Reduce the load to the initial load, keep it for 24 hrs and note the final readings of the dial gauge.

10. Quickly dismantle the specimen assembly and remove the excess water on the soil specimen in oven, note its dry weight.

IIT Gandhinagar, Soil Mechanics Lab

Page2

INDIAN INSTITUTE OF TECHNOLOGY GANDHINAGAR


Department of Civil Engineering
Soil Mechanics Laboratory
CALCULATIONS:
1. Height of solids (HS) is calculated from the equation
HS = WS/ (GS.wA)

2. Void ratio. Voids ratio at the end of various pressures are calculated from equation
e = (H HS)/HS
3. Coefficient of consolidation. The Coefficient of consolidation at each pressure increment is calculated by using the
following equations:
i.

Cv = 0.197 d2/t50 (Log fitting method)

ii.

Cv = 0.848 d2/t90 (Square fitting method)

In the log fitting method, a plot is made between dial readings and logarithmic of time, and the time corresponding to 50%
consolidation is determined.
In the square root fitting method, a plot is made between dial readings and square root of time, and the time corresponding to
90% consolidation is determined. The values of C v are recorded in Table.

4. Compression Index. To determine the compression index, a plot of voids ratio (e) Vslog (t) is made. The virgin
compression curve would be a straight line and the slope of this line would give the compression index C c.
5. Coefficient of compressibility. It is calculated as follows
av = 0.435 Cc/ (Avg. pressure) for the increment
where Cc = Coefficient of compressibility
6. Coefficient of permeability. It is calculated as follows
k = Cv.av.w/ (1+eo).
GRAPHS:
1.

Dial reading VS log of time or

2.

Dial reading VS square root of time.

3.

Voids ratio VS log (average pressure for the increment).

General Remarks:
1.

While preparing the specimen, attempts has to be made to have the soil strata orientated in the same direction in the
consolidation apparatus.

2.

During trimming care should be taken in handling the soil specimen with least pressure.

3.

Smaller increments of sequential loading have to be adopted for soft soils.

IIT Gandhinagar, Soil Mechanics Lab

Page3

INDIAN INSTITUTE OF TECHNOLOGY GANDHINAGAR


Department of Civil Engineering
Soil Mechanics Laboratory

OBSERVATION AND READING:


Table: Data Sheet for Consolidation Test: Time-Displacement Relationship
Ring Dimensions: Diameter: ____________

Area: _____________

Initial Data:

Specific Gravity of Soil: ___________

Specimen Ht.___________

Height: _____________

Mass of top porous stone + cap + ball bearing: __________

Pressure
Intensity

0.1

0.2

0.5

(Kg/cm )
Time (min)
0
0.25
1
2
4
8
15
30
1 hr
2 hrs
4 hrs
8 hrs
24 hrs

IIT Gandhinagar, Soil Mechanics Lab

Page4

INDIAN INSTITUTE OF TECHNOLOGY GANDHINAGAR


Department of Civil Engineering
Soil Mechanics Laboratory
Table II: Data Sheet for Consolidation Test: Pressure-Voids Ratio
Applied
Pressure

Final

Change

dial

Specimen

reading Height

in Final

Height

Specimen of
Height

solids

Height

Void

of voids ratio

Average

Height

during
Consolidation

Fitting
Time, t90

Coefficient

of

Consolidation,
cv

0
0.1
0.2
0.5
1.0
2.0
4.0
8.0
2.0
0.5
0.1

IIT Gandhinagar, Soil Mechanics Lab

Page5

You might also like