AutoCAD 2007 Tutorial

First Level: 2D Fundamentals

Text by

Randy H. Shih
Oregon Institute of Technology
MultiMedia CD by
INSIDE:

Jack Zecher
Indiana University Purdue University Indianapolis

MultiMedia CD
by Jack Zecher

SDC

PUBLICATIONS

An audio/visual
presentation of the
tutorial exercises

Schroff Development Corporation

www.schroff.com

www.schroff-europe.com

Visit our website to learn more about this and other books:

AutoCAD 2007 Tutorial

Copyrighted
Material

Chapter 1

AutoCAD Fundamentals

Copyrighted
Material
Copyrighted
Material

Create and Save AutoCAD Drawing

Files
Use the AutoCAD Visual Reference
Commands
Draw, Using the LINE and CIRCLE
Commands
Use the ERASE Command
Define Positions Using the Basic Entry
Methods
Use the AutoCAD Pan Realtime Option

Copyrighted
Material

1-1

1-2

AutoCAD 2007 Tutorial

Copyrighted
Material

Introduction

Learning to use a CAD system is similar to learning a new language. It is necessary to

begin with the basic alphabet and learn how to use it correctly and effectively through
practice. This will require learning some new concepts and skills as well as learning a
different vocabulary. All CAD systems create designs using basic geometric entities.
Many of the constructions used in technical designs are based upon two-dimensional
planar geometry. The method and number of operations that are required to accomplish
the constructions are different from one system to another.
In order to become effective in using a CAD system, we must learn to create geometric
entities quickly and accurately. In learning to use a CAD system, lines and circles are
the first two, and perhaps the most important two, geometric entities that one should
master the skills of creating and modifying. Straight lines and circles are used in almost
all technical designs. In examining the different types of planar geometric entities, the
importance of lines and circles becomes obvious. Triangles and polygons are planar
figures bounded by straight lines. Ellipses and splines can be constructed by connecting
arcs with different radii. As one gains some experience in creating lines and circles,
similar procedures can be applied to create other geometric entities. In this chapter,
the different ways of creating lines and circles in AutoCAD 2007 are examined.

Copyrighted
Material

Starting Up AutoCAD 2007

1. Select the AutoCAD 2007 option on the Program menu or select the
AutoCAD 2007 icon on the Desktop. Once the program is loaded into
memory, the AutoCAD 2007 drawing screen will appear on the screen.

Copyrighted
Material

Copyrighted
Material

AutoCAD Fundamentals

1-3

Copyrighted
Material

2. Choose AutoCAD Classic as the initial

workspace.

3. Select Dont Show me this again and click OK

to continue.

Note that AutoCAD automatically assigns generic name, Drawing X, as new

drawings are created. In our example, AutoCAD opened the graphics window
using the default system units and assigned the drawing name Drawing1.

Copyrighted
Material
Copyrighted
Material
4. Close the Tool Palettes by clicking once on
Close button located at the upper right corner
of the window as shown.

Copyrighted
Material

5. Close the Sheet Set Manager by clicking once

on the Close button located at the upper right
corner of the window as shown.

1-4

AutoCAD 2007 Tutorial

Copyrighted
Material

Drawing Units Setup

Every object we construct in a CAD system is measured in units. We should determine

the value of the units within the CAD system before creating the first geometric entities.

1. In the pull-down menus, select:

[Format]
[Units]

Copyrighted
Material
2. In the Drawing Units dialog box, set the Length Type to Decimal. This will set
the measurement to the default English units, inches.

Copyrighted
Material
Copyrighted
Material

3. Set the Precision to two digits after the decimal point as shown in the above
figure.
4. Pick OK to exit the Drawing Units dialog box.

AutoCAD Fundamentals

1-5

Copyrighted
Material

Drawing Area Setup

Next, we will set up the Drawing Limits; setting the Drawing Limits controls the
extents of the display of the grid. It also serves as a visual reference that marks the
working area. It can also be used to prevent construction outside the grid limits and as a
plot option that defines an area to be plotted/printed. Note that this setting does not limit
the region for geometry construction.
1. In the pull-down menus, select:
[Format]
[Drawing Limits]

Copyrighted
Material
2. In the command prompt area, near the bottom of the AutoCAD drawing
screen, the message Reset Model Space Limits: Specify lower left corner or
[On/Off] <0.00,0.00>: is displayed. Press the ENTER key once to accept the
default coordinates <0.00,0.00>.

Copyrighted
Material

3. In the command prompt area, the message Specify upper right corner
<0.00,0.00>: is displayed. Press the ENTER key once to accept the default
coordinates <12.00,9.00>.

Copyrighted
Material

4. On your own, move the graphic cursor near the upper-right comer inside
the drawing area and note that the drawing area is unchanged. (The Drawing
Limits command is used to set the drawing area; but the display will not be
adjusted until a display command is used.)

1-6

AutoCAD 2007 Tutorial

Copyrighted
Material
5. In the pull-down menus, select:
[View]
[Zoom]
[All]

 The Zoom All command will adjust

the display so that all objects in the
drawing are displayed to be as large as
possible. If no objects are constructed,
the Drawing Limits are used to adjust
the current viewport.
6. Move the graphic cursor near the upperright comer inside the drawing area and
note that the display area is updated.

Copyrighted
Material

Using the Line Command

1. Click on the Info Palette option in the Help

pull-down menu to activate the Quick Help
option.

Copyrighted
Material

2. Move the graphics cursor to the first icon in the Draw toolbar.
This icon is the Line icon. A help-tip box appears next to the
cursor and a brief description of the icon is displayed at the
bottom of the AutoCAD drawing screen: Creates Straight
line segments: LINE.

3. Select the icon by clicking once with the left-mouse-button,

which will activate the Line command.

Notice a brief explanation of the selected
command is displayed in the Info Palette
window. It is highly recommended that you read
the explanations to gain some insights on the
general procedure of using AutoCAD.

Copyrighted
Material

4. In the Info Palette window, click To draw

lines to open the AutoCAD Help window and
get a more detailed explanation on the procedure.

AutoCAD Fundamentals

1-7

Copyrighted
Material

 The general procedure to create a line

in AutoCAD is displayed in the Info
Palette window.
5. Click on Close button located at the
upper left corner of the Info Palette
window as shown.

Copyrighted
Material

6. In the command prompt area, near the bottom of the AutoCAD drawing screen,
the message _line Specify first point: is displayed. AutoCAD expects us to
identify the starting location of a straight line. Move the graphics cursor inside
the graphics window and watch the display of the coordinates of the graphics
cursor at the bottom of the AutoCAD drawing screen. The three numbers
represent the location of the cursor in the X, Y, and Z directions. We can treat
the graphics window as if it was a piece of paper and we are using the graphics
cursor as if it were a pencil with which to draw.

Copyrighted
Material
Coordinates of the location
of the graphics cursor.

5
3

Copyrighted
Material
2

 We will create a freehand sketch of a fivepoint star using the Line command. Do not
be overly concerned with the actual size or
the accuracy of your freehand sketch. This
exercise is to give you a feel for the
AutoCAD 2007 user interface.

1-8

AutoCAD 2007 Tutorial

Copyrighted
Material

7. We will start at a location near

the bottom of the graphics window.
Left-click once to position the
starting point of our first line.
This will be point 1 of our sketch.

 The two numbers, displayed next to

the cursor, represent the current
cursor position. Note that the same
two numbers are also displayed at the
lower left corner of the AutoCAD
main window. The displaying of
tooltips is known as the Dynamic
Input option. Tooltips are displayed
near the cursor, which are
dynamically updated as the cursor
moves.

Copyrighted
Material

8. Next move the cursor upward

and toward the right side of
point 1. Notice the rubber-band
line that follows the graphics
cursor in the graphics window.
Left-click again (point 2) and we
have created the
first line of our sketch.

Copyrighted
Material

The two numbers, displayed next

to the cursor, represent the
distance and angle of the current
cursor position relative to the
previously selected location on
the screen. This feature is also
part of the Dynamic Input
option. A more detailed
discussion on how to utilize this
feature is presented in Chapter 3
of this text.

Copyrighted
Material

AutoCAD Fundamentals

1-9

Copyrighted
Material

9. Move the cursor to the left of

point 2 and create a horizontal line
roughly about the same length as
the first line on the screen.

Copyrighted
Material
5

10. Repeat the above steps and complete

the freehand sketch by adding three more
lines (from point 3 to point 4, point 4 to
point 5, and then connect to point 5 back
to point 1).

Copyrighted
Material
4

11. Notice that the Line command remains activated even after
we connected the last segment of the line to the starting
point (point 1) of our sketch. Inside the graphics window,
click once with the right-mouse-button and a popup menu
appears on the screen.

12. Select Enter with the left-mouse-button to end the Line

command. (This is equivalent to hitting the [ENTER] key
on the keyboard.)

Copyrighted
Material

13. On your own, move the cursor near point 2 and point 3, and estimate the length of
the horizontal line by watching the displayed coordinates for each point at the
bottom of the screen.

1-10

AutoCAD 2007 Tutorial

Copyrighted
Material

Visual Reference

The method we just used to create the freehand sketch is known as the interactive
method, where we use the cursor to specify locations on the screen. This method is
perhaps the fastest way to specify locations on the screen. However, it is rather difficult
to try to create a line of a specific length by watching the displayed coordinates. It would
be helpful to know what one inch or one meter looks like on the screen while we are
creating entities. AutoCAD 2007 provides us with many tools to aid the construction
of our designs. We will use the GRID and SNAP options to get a visual reference as to
the size of objects and learn to restrict the movement of the cursor to a set increment on
the screen.
The Status Bar area is located at the bottom of the AutoCAD drawing screen. The words
SNAP, GRID, ORTHO, POLAR, OSNAP, OTRACK, DUCS, LWT and MODEL appearing
to the right of the coordinates are buttons that we can left-click to turn these special
options ON and OFF. When the corresponding button is highlighted, the specific option
is turned ON. These buttons act as toggle switches; each click of the button will toggle
the option ON or OFF. Using the buttons is a quick and easy way to make changes to
these drawing aid options. We can toggle the options on and off in the middle of another
command.

Copyrighted
Material
Option Buttons

GRID On

Copyrighted
Material

1. Left-click the GRID button in the Status Bar to turn On the GRID option. (Notice
in the command prompt area, the message <Grid on> is also displayed.)

Copyrighted
Material

2. Move the cursor inside the graphics window, and estimate the distance in between
the grid points by watching the coordinates display at the bottom of the screen.

AutoCAD Fundamentals

1-11

Copyrighted
Material

The GRID option creates a pattern of dots

that extends over an area on the screen.
Using the grid is similar to placing a sheet
of grid paper under a drawing. The grid
helps you align objects and visualize the
distance between them. The grid is not
displayed in the plotted drawing. The
default grid spacing, which means the
distance in between two dots on the screen,
is 0.5 inches. We can see that the sketched
horizontal line in the sketch is about 4.0
inches long.

Copyrighted
Material

DYN Off

1. Left-click the DYN button in the Status Bar to turn Off the Dynamic
Input option.

Copyrighted
Material

The DYN button allows the quick toggle of the Dynamic Input option.
We will switch off this option to discuss the basic input options available in
AutoCAD. A more detailed discussion on this feature is presented in Chapter
three.

SNAP On

1. Left-click the SNAP button in the Status Bar to turn On the SNAP option.

Copyrighted
Material

1-12

AutoCAD 2007 Tutorial

Copyrighted
Material

2. Move the cursor inside the graphics window, and move the cursor diagonally
on the screen. Observe the movement of the cursor and watch the
coordinates display at the bottom of the screen.

The SNAP option controls an invisible rectangular grid that restricts cursor
movement to specified intervals. When SNAP mode is on, the screen cursor and
all input coordinates are snapped to the nearest point on the grid. The default snap
interval is 0.5 inches, and aligned to the grid points on the screen.

3. Click on the Line icon in the Draw toolbar. In the command

prompt area, the message _line Specify first point: is
displayed.

Copyrighted
Material

4. On your own, create another sketch of the five-point star with the GRID and
SNAP options switched ON.

Copyrighted
Material
Copyrighted
Material

5. Use the right-mouse-button and select Enter in the popup

menu to end the Line command if you have not done so.

AutoCAD Fundamentals

1-13

Copyrighted
Material

Using the ERASER Command

 One of the advantages of using a CAD system is the ability to remove entities without
leaving any marks. We will erase two of the lines using the Erase command.
1. Pick Erase in the Modify toolbar. (The icon is
the first icon in the Modify toolbar. The icon is
a picture of an eraser at the end of a pencil.)
The message Select objects is displayed in
the command prompt area and AutoCAD awaits
us to select the objects to erase.

Copyrighted
Material

2. Left-click the SNAP button on the Status Bar to turn off the SNAP option so
that we can more easily move the cursor on top of objects. We can toggle the
Status Bar options ON or OFF in the middle of another command.

Copyrighted
Material

3. Select any two lines on the screen; the selected lines are displayed as dashed
lines as shown in the figure below.

Copyrighted
Material

4. Right-mouse-click once to accept the selections. The selected two lines are
erased.

1-14

AutoCAD 2007 Tutorial

Copyrighted
Material

Repeat the Last Command

1. Inside the graphics window, click once with the rightmouse-button to bring up the popup option menu.
2. Pick Repeat Erase, with the left-mouse-button, in the
popup menu to repeat the last command. Notice the other
options available in the popup menu.

AutoCAD 2007 offers many options to accomplish the

same task. Throughout this text, we will emphasize the
use of the AutoCAD Heads-up DesignTM interface,
which means we focus on the screen, not on the
keyboard.

Copyrighted
Material

3. Move the cursor to a location that is above and toward the left side of the
entities on the screen. Left-mouse-click once to start a corner of a rubber-band
window.

First corner

Copyrighted
Material
Second corner

4. Move the cursor toward the right and below the entities, and then left-mouseclick to enclose all the entities inside the selection window. Notice all entities
that are inside the window are selected.

Copyrighted
Material

5. Inside the graphics window, right-mouse-click once to proceed with erasing

the selected entities.

On your own, create a free-hand sketch of your choice using the Line command.
Experiment with using the different commands we have discussed so far. Also try
switching the GRID and SNAP options ON and OFF in the middle of a command.

AutoCAD Fundamentals

1-15

Copyrighted
Material

The CAD Database and the User Coordinate System

 Designs and drawings created in a CAD system are

usually defined and stored using sets of points in what is
called world space. In most CAD systems, the world
space is defined using a three-dimensional Cartesian
coordinate system. Three mutually perpendicular axes,
usually referred to as the X-, Y-, and Z-axes, define this
system. The intersection of the three coordinate axes
forms a point called the origin. Any point in world space
can then be defined as the distance from the origin in the
X-, Y- and Z- directions. In most CAD systems, the
directions of the arrows shown on the axes identify the
positive sides of the coordinates.

Copyrighted
Material

A CAD file, which is the electronic version of the design, contains data that describe
the entities created in the CAD system. Information such as the coordinate values in
world space for all endpoints, center points, etc., along with the descriptions of the
types of entities are all stored in the file. Knowing that AutoCAD stores designs by
keeping coordinate data helps us understand the inputs required to create entities.

3D UCS icon

Copyrighted
Material

The icon near the bottom left corner of the default AutoCAD graphics window
shows the positive X-direction and positive Y-direction of the coordinate system
that is active. In AutoCAD, the coordinate system that is used to create entities is
called the user coordinate system (UCS). By default, the user coordinate system
is aligned to the world coordinate system (WCS). The world coordinate system is
a coordinate system used by AutoCAD as the basis for defining all objects and other
coordinate systems defined by the users. We can think of the origin of the world
coordinate system as a fixed point being used as a reference for all measurements.
The default orientation of the Z-axis can be considered as positive values in front of
the monitor and negative values inside the monitor.

Copyrighted
Material

1-16

AutoCAD 2007 Tutorial

Copyrighted
Material

Changing to the 2D UCS Icon Display

 In AutoCAD 2007, the UCS icon is displayed in various ways to help us visualize
the orientation of the drawing plane.

Copyrighted
Material

1. In the pull-down menus, select:

[View]
[Display]

[UCS Icon]
[Properties]

Copyrighted
Material
2. In the UCS icon style section, switch
to the 2D option as shown.

Copyrighted
Material

3. Click OK to accept the settings.

 Note the W symbol in the UCS icon

indicates the UCS is aligned to the world
coordinate system.

AutoCAD Fundamentals

1-17

Copyrighted
Material

Cartesian and Polar Coordinate Systems

In a two-dimensional space, a point can be represented using different coordinate

systems. The point can be located, using a Cartesian coordinate system, as X and
Y units away from the origin. The same point can also be located using the polar
coordinate system, as r and units away from the origin.

Copyrighted
Material

For planar geometry, the polar coordinate system is very useful for certain
applications. In the polar coordinate system, points are defined in terms of a radial
distance, r, from the origin and an angle between the direction of r and the positive
X axis. The default system for measuring angles in AutoCAD 2007 defines positive
angular values as counter-clockwise from the positive X-axis.

Copyrighted
Material

Absolute and Relative Coordinates

AutoCAD 2007 also allows us to use absolute

and relative coordinates to quickly construct objects.
Absolute coordinate values are measured from the
current coordinate system's origin point. Relative
coordinate values are specified in relation to previous
coordinates.

Note that the coordinate display area can also be
used as a toggle switch; each left-mouse-click will
toggle the coordinate display on or off.

Copyrighted
Material

In AutoCAD 2007, the absolute coordinates and the relative coordinates can be used
in conjunction with the Cartesian and polar coordinate systems. By default, AutoCAD
expects us to enter values in absolute Cartesian coordinates, distances measured from the
current coordinate system's origin point. We can switch to using the relative coordinates
by using the @ symbol. The @ symbol is used as the relative coordinates specifier,
which means that we can specify the position of a point in relation to the previous point.

1-18

AutoCAD 2007 Tutorial

Copyrighted
Material

Defining Positions

In AutoCAD, there are five methods for specifying the locations of points when we
create planar geometric entities.

Interactive method: Use the cursor to select on the screen.

Absolute coordinates (Format: X,Y): Type the X and Y coordinates to locate the
point on the current coordinate system relative to the origin.

Relative rectangular coordinates (Format: @X,Y): Type the X and Y
coordinates relative to the last point.

Copyrighted
Material

Relative polar coordinates (Format: @Distance<angle): Type a distance and

angle relative to the last point.

Direct Distance entry technique: Specify a second point by first moving the
cursor to indicate direction and then entering a distance.

The Guide Plate

We will next create a mechanical design using the different coordinate entry methods.

Copyrighted
Material

Copyrighted
Material

Use the Erase command and erase all entities on the screen before
proceeding to the next section.

AutoCAD Fundamentals

1-19

Copyrighted
Material

The rule for creating CAD designs and drawings is that they should be created
at full size using real-world units. The CAD database contains all the
definitions of the geometric entities and the design is considered as a virtual,
full-sized object. Only when a printer or plotter transfers the CAD design to
paper is the design scaled to fit on a sheet. The tedious task of determining a
scale factor so that the design will fit on a sheet of paper is taken care of by
the CAD system. This allows the designers and CAD operators to concentrate
their attention on the more important issues the design.
1. Select the Line command icon in the Draw toolbar. In the
command prompt area, near the bottom of the AutoCAD
graphics window, the message _line Specify first point: is
displayed. AutoCAD expects us to identify the starting
location of a straight line.

Copyrighted
Material

2. In the command prompt area, we will locate the starting point

of our design at the origin of the world coordinate system.
Command: _line Specify first point: 0,0 [ENTER]
(Type 0,0 in the command prompt area and press the
[ENTER] key once.)

3. We will create a horizontal line by entering the absolute coordinates of the

second point.

Copyrighted
Material
Specify next point or [Undo]: 5.5,0 [ENTER]

Copyrighted
Material

(0,0)

(5.5,0)

1-20

AutoCAD 2007 Tutorial

Copyrighted
Material

The line we created is aligned to the bottom edge of the drawing window. Let
us adjust the view of the line by using the Pan Realtime command.
4. Click on the Pan Realtime icon in the
Standard toolbar area. The icon is the picture of
a hand with four arrows.
 The Pan command enables us to move the view
to a different position. This function acts as if
you are using a video camera.

5. Move the cursor, which appears as a hand inside the graphics window, near
the center of the drawing window, then push down the left-mouse-button and
drag the display toward the right and top side until we can see the sketched
line. (Notice the scroll bars can also be used to adjust viewing of the display.)

Copyrighted
Material

6. Press the [Esc] key to exit the Pan command. Notice that AutoCAD goes
back to the Line command.
7. We will create a vertical line by using the relative rectangular coordinates
entry method, relative to the last point we specified:
Specify next point or [Close/Undo]: @0,2.5 [ENTER]
8. We can mix any of the entry methods in positioning the locations of the
endpoints. Move the cursor to the Status Bar area, and turn ON the GRID and
SNAP options.

Copyrighted
Material
SNAP and GRID On

9. Create the next line by picking the location, world coordinates

(8,2.5), on the screen.

Copyrighted
Material

10. We will next use the relative polar coordinates entry method, relative to the
last point we specified:
Specify next point or [Close/Undo]: @3<90 [ENTER]
(Distance is 3 inches with an angle of 90 degrees.)

AutoCAD Fundamentals

1-21

Copyrighted
Material
Reference Coordinate System
aligned at the previous point

11. Using the relative rectangular

coordinates entry method to
create the next line, we can
imagine a reference coordinate
system aligned at the previous
point. Coordinates are measured
along the two reference axes.
Specify next point or [Close/Undo]:
@-1.5,1 [ENTER]
(-1.5 and 1 inches are measured
relative to the reference point.)

Copyrighted
Material

12. Move the cursor directly to the left of the last

point and use the direct distance entry technique
by entering 6.5 [ENTER].

13. For the last segment of the sketch, we can use the Close
option to connect back to the starting point. Inside the
graphics window, right-mouse-click and a popup menu
appears on the screen.

Copyrighted
Material

14. Select Close with the left-mouse-button to connect back

to the starting point and end the Line command.

Copyrighted
Material

1-22

AutoCAD 2007 Tutorial

Copyrighted
Material

Creating Circles

The menus and toolbars in AutoCAD 2007 are designed to allow the CAD operators to
quickly activate the desired commands. Besides using the Draw toolbar, we can also
select the different Draw commands through the pull-down menus.
1. In the pull-down menus, select:

[Draw]
[Circle]
[Center, Diameter]

Copyrighted
Material
Copyrighted
Material
Notice the different options available under the circle submenu:

Center Point: Draws a circle based on a center point and a diameter or a radius.

2 Points: Draws a circle based on two endpoints of the diameter.

3 Points: Draws a circle based on three points on the circumference.

TTRTangent, Tangent, Radius: Draws a circle with a specified radius

tangent to two objects.

TTTTangent, Tangent, Tangent: Draws a circle tangent to three objects.

Copyrighted
Material

AutoCAD Fundamentals

1-23

Copyrighted
Material

2. In the command prompt area, the message Specify center point for circle or
[3P/2P/Ttr (tan tan radius)]: is displayed. AutoCAD expects us to identify
the location of a point or enter an option. We can use any of the four
coordinate entry methods to identify the desired location. We will enter the
world coordinates (2.5,3) as the center point for the first circle.
Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 2.5,3 [ENTER]

3. In the command prompt area, the message Specify diameter of circle: is

displayed.
Specify diameter of circle: 2.5 [ENTER]

Copyrighted
Material
Copyrighted
Material

4. Inside the graphics window, right-mouseclick to bring up the popup option menu.
5. Pick Repeat Center, Diameter with the
left-mouse-button in the popup menu to
repeat the last command.

Copyrighted
Material

6. Using the relative rectangular coordinates

entry method, relative to the center-point
coordinates of the first circle, we specify the
location as (2.5,2).

Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: @2.5,2 [ENTER]

1-24

AutoCAD 2007 Tutorial

Copyrighted
Material

7. In the command prompt area, the message Specify Diameter of circle:

<2.50> is displayed. The default option for the Circle command in
AutoCAD is to specify the radius and the last radius used is also displayed
in brackets.
Specify Diameter of circle<2.50>: 1.5 [ENTER]

Copyrighted
Material
Copyrighted
Material

Saving the CAD Design

1. In the pull-down menus, select:

[File]
[Save As]

 Note the command can also be activated

with quick-key combination of
[Ctrl]+[Shift]+[S].

Copyrighted
Material

AutoCAD Fundamentals

1-25

Copyrighted
Material

2. In the Save Drawing As dialog box, select the folder in which you want to
store the CAD file and enter GuidePlate in the File name box.

Select the folder

to store the file.

Copyrighted
Material
Enter GuidePlate

3. Pick Save in the Save Drawing As dialog box to accept the selections and
save the file.

Copyrighted
Material

Exit AutoCAD 2007

To exit AutoCAD 2007, select File then choose Exit from

the pull-down menu or type QUIT at the command prompt.
Note the command can also be activated with quick-key
combination of [Ctrl]+[Q].

Copyrighted
Material

1-26

AutoCAD 2007 Tutorial

Copyrighted
Material

Questions:

1. What are the advantages and disadvantages of using CAD systems to create
engineering drawings?
2. How do the GRID and SNAP options assist us in sketching?

3. List and describe the different coordinate entry methods available in AutoCAD?
4. List and describe two types of coordinate systems commonly used for planar
geometry.
5. Identify the following commands:
(a)

Copyrighted
Material

(b)

(c)

(d)

Copyrighted
Material
Copyrighted
Material

Tan, Tan, Radius

AutoCAD Fundamentals

Copyrighted
Material

Exercises: (All dimensions are in inches.)

1.

Copyrighted
Material
2.

Copyrighted
Material
Copyrighted
Material

1-27

1-28

3.

AutoCAD 2007 Tutorial

Copyrighted
Material
Copyrighted
Material

4.

Copyrighted
Material
Copyrighted
Material