Creating and Simulating a Simple Model - MATLAB & Simulink

Pgina 1 de 15

Creating and Simulating a Simple Model

Building a Simscape Diagram
In this example, you are going to model a simple mechanical system and observe its behavior under
various conditions. This tutorial illustrates the essential steps to building a physical model and makes you
familiar with using the basic Simscape blocks.
The following schematic represents a simple model of a car suspension. It consists of a spring and damper
connected to a body (represented as a mass), which is agitated by a force. You can vary the model
parameters, such as the stiffness of the spring, the mass of the body, or the force profile, and view the
resulting changes to the velocity and position of the body.

To create an equivalent Simscape diagram, follow these steps:

1. Open the Simulink Library Browser, as described in Simscape Block Libraries.
2. Create a new Simulink model using the Blank Model template. The software creates an empty model
in memory and displays it in a new model editor window.
Note Alternately, you can type ssc_new at the MATLAB Command prompt, to create a new model
prepopulated with certain required and commonly used blocks. For more information, see Creating a New
Simscape Model.

3. Open the Simscape > Foundation Library > Mechanical> Translational Elements library.
4. Drag the Mass, Translational Spring, Translational Damper, and two Mechanical Translational
Reference blocks into the model window.
5. Orient the blocks as shown in the following illustration. To rotate a block, select it and press Ctrl+R.

https://www.mathworks.com/help/physmod/simscape/ug/creating-and-simulating-a-si... 13/10/2016

Creating and Simulating a Simple Model - MATLAB & Simulink

Pgina 2 de 15

6. Connect the Translational Spring, Translational Damper, and Mass blocks to one of the Mechanical
Translational Reference blocks as shown in the next illustration.

https://www.mathworks.com/help/physmod/simscape/ug/creating-and-simulating-a-si... 13/10/2016

Creating and Simulating a Simple Model - MATLAB & Simulink

Pgina 3 de 15

7. To add the representation of the force acting on the mass, open the Simscape > Foundation Library >
Mechanical> Mechanical Sources library and add the Ideal Force Source block to your diagram.
To reflect the correct direction of the force shown in the original schematic, flip the block by selecting
Diagram > Rotate& Flip > Flip Block > Up-Down from the top menu bar of the model window.
Connect the block's port C (for "case") to the second Mechanical Translational Reference block, and its
port R (for "rod") to the Mass block, as shown below.

https://www.mathworks.com/help/physmod/simscape/ug/creating-and-simulating-a-si... 13/10/2016

Creating and Simulating a Simple Model - MATLAB & Simulink

Pgina 4 de 15

8. Add the sensor to measure speed and position of the mass. Place the Ideal Translational Motion
Sensor block from the Mechanical Sensors library into your diagram and connect it as shown below.

https://www.mathworks.com/help/physmod/simscape/ug/creating-and-simulating-a-si... 13/10/2016

Creating and Simulating a Simple Model - MATLAB & Simulink

Pgina 5 de 15

9. Now you need to add the sources and scopes. They are found in the regular Simulink libraries. Open
the Simulink > Sources library and copy the Signal Builder block into the model. Then open the
Simulink > Sinks library and copy two Scope blocks. Rename one of the Scope blocks to Velocity
and the other to Position.

https://www.mathworks.com/help/physmod/simscape/ug/creating-and-simulating-a-si... 13/10/2016

Creating and Simulating a Simple Model - MATLAB & Simulink

Pgina 6 de 15

10. Every time you connect a Simulink source or scope to a Simscape diagram, you have to use an
appropriate converter block, to convert Simulink signals into physical signals and vice versa. Open the
Simscape > Utilities library and copy a Simulink-PS Converter block and two PS-Simulink Converter
blocks into the model. Connect the blocks as shown below.

https://www.mathworks.com/help/physmod/simscape/ug/creating-and-simulating-a-si... 13/10/2016

Creating and Simulating a Simple Model - MATLAB & Simulink

Pgina 7 de 15

11. Each topologically distinct physical network in a diagram requires exactly one Solver Configuration
block, found in the Simscape > Utilities library. Copy this block into your model and connect it to the
circuit by creating a branching point and connecting it to the only port of the Solver Configuration block.
Your diagram now should look like this.

https://www.mathworks.com/help/physmod/simscape/ug/creating-and-simulating-a-si... 13/10/2016

Creating and Simulating a Simple Model - MATLAB & Simulink

Pgina 8 de 15

12. Your block diagram is now complete. Save it as mech_simple.

Modifying Initial Settings

After you have put together a block diagram of your model, as described in the previous section, you need
to select a solver and provide the correct values for configuration parameters.
To prepare for simulating the model, follow these steps:
1. Select a Simulink solver. On the top menu bar of the model window, select Simulation > Model
Configuration Parameters. The Configuration Parameters dialog box opens, showing the Solver
node.
Under Solver options, set Solver to ode23t (mod.stiff/Trapezoidal).
Expand Additional options and set Max step size to 0.2.
Also note that Simulation time is specified to be between 0 and 10 seconds. You can adjust this
setting later, if needed.

https://www.mathworks.com/help/physmod/simscape/ug/creating-and-simulating-a-si... 13/10/2016

Creating and Simulating a Simple Model - MATLAB & Simulink

Pgina 9 de 15

Click OK to close the Configuration Parameters dialog box.

2. Save the model.

Running the Simulation

After you've put together a block diagram and specified the initial settings for your model, you can run the
simulation.
1. The input signal for the force is provided by the Signal Builder block. The signal profile is shown in the
illustration below. It starts with a value of 0, then at 4 seconds there is a step change to 1, and then it
changes back to 0 at 6 seconds. This is the default profile.

https://www.mathworks.com/help/physmod/simscape/ug/creating-and-simulating-a-si... 13/10/2016

Creating and Simulating a Simple Model - MATLAB & Simulink

Pgina 10 de 15

The Velocity scope outputs the mass velocity, and the Position scope outputs the mass displacement
as a function of time. Double-click both scopes to open them.
2. To run the simulation, click

in the model window toolbar. The Simscape solver evaluates the

model, calculates the initial conditions, and runs the simulation. For a detailed description of this
process, see How Simscape Simulation Works. Completion of this step may take a few seconds. The
message in the bottom-left corner of the model window provides the status update.
3. Once the simulation starts running, the Velocity and Position scope windows display the simulation
results, as shown in the next illustration.

https://www.mathworks.com/help/physmod/simscape/ug/creating-and-simulating-a-si... 13/10/2016

Creating and Simulating a Simple Model - MATLAB & Simulink

Pgina 11 de 15

In the beginning, the mass is at rest. Then at 4 seconds, as the input signal changes abruptly, the mass
velocity spikes in the positive direction and gradually returns to zero. The mass position at the same
time changes more gradually, on account of inertia and damping, and stays at the new value as long as
the force is acting upon it. At 6 seconds, when the input signal changes back to zero, the velocity gets a
mirror spike, and the mass gradually returns to its initial position.
You can now adjust various inputs and block parameters and see their effect on the mass velocity and
displacement.

Adjusting the Parameters

After running the initial simulation, you can experiment with adjusting various inputs and block parameters.
Try the following adjustments:
1. Change the force profile.
2. Change the model parameters.
3. Change the mass position output units.
Changing the Force Profile
This example shows how a change in the input signal affects the force profile, and therefore the mass
displacement.
1. Double-click the Signal Builder block to open it.
2. Click the first vertical segment of the signal profile and drag it from 4 to 2 seconds, as shown below.
Close the block dialog.

https://www.mathworks.com/help/physmod/simscape/ug/creating-and-simulating-a-si... 13/10/2016

Creating and Simulating a Simple Model - MATLAB & Simulink

Pgina 12 de 15

3. Run the simulation. The simulation results are shown in the following illustration.

https://www.mathworks.com/help/physmod/simscape/ug/creating-and-simulating-a-si... 13/10/2016

Creating and Simulating a Simple Model - MATLAB & Simulink

Pgina 13 de 15

Changing the Model Parameters

In our model, the force acts on a mass against a translational spring and damper, connected in parallel.
This example shows how changes in the spring stiffness and damper viscosity affect the mass
displacement.
1. Double-click the Translational Spring block. Set its Spring rate to 2000 N/m.
2. Run the simulation. The increase in spring stiffness results in smaller amplitude of mass displacement,
as shown in the following illustration.

3. Next, double-click the Translational Damper block. Set its Damping coefficient to 500 N/(m/s).
4. Run the simulation. Because of the increase in viscosity, the mass is slower both in reaching its
maximum displacement and in returning to the initial position, as shown in the following illustration.

https://www.mathworks.com/help/physmod/simscape/ug/creating-and-simulating-a-si... 13/10/2016

Creating and Simulating a Simple Model - MATLAB & Simulink

Pgina 14 de 15

Changing the Mass Position Output Units

In our model, we have used the PS-Simulink Converter block in its default parameter configuration, which
does not specify units. Therefore, the Position scope outputs the mass displacement in the default length
units, that is, in meters. This example shows how to change the output units for the mass displacement to
millimeters.
1. Double-click the PS-Simulink Converter1 block. Type mm in the Output signal unit combo box and click
OK.
2. Run the simulation. In the Position scope window, click
to autoscale the scope axes. The mass
displacement is now output in millimeters, as shown in the following illustration.

More About

Basic Principles of Modeling Physical Networks

Modeling Best Practices

https://www.mathworks.com/help/physmod/simscape/ug/creating-and-simulating-a-si... 13/10/2016

Creating and Simulating a Simple Model - MATLAB & Simulink

Pgina 15 de 15

https://www.mathworks.com/help/physmod/simscape/ug/creating-and-simulating-a-si... 13/10/2016