Lab Configuring and Verifying Extended ACLs

Topology

2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public.

Page 1 of 8

Lab Configuring and Verifying Extended ACLs

Addressing Table
Device
R1

Interface

IP Address

Subnet Mask

Default Gateway

G0/1

192.168.10.1

255.255.255.0

N/A

Lo0

192.168.20.1

255.255.255.0

N/A

S0/0/0 (DCE)

10.1.1.1

255.255.255.252

N/A

S0/0/0

10.1.1.2

255.255.255.252

N/A

S0/0/1 (DCE)

10.2.2.2

255.255.255.252

N/A

Lo0

209.165.200.225

255.255.255.224

N/A

Lo1

209.165.201.1

255.255.255.224

N/A

G0/1

192.168.30.1

255.255.255.0

N/A

Lo0

192.168.40.1

255.255.255.0

N/A

S0/0/1

10.2.2.1

255.255.255.252

N/A

S1

VLAN 1

192.168.10.11

255.255.255.0

192.168.10.1

S3

VLAN 1

192.168.30.11

255.255.255.0

192.168.30.1

PC-A

NIC

192.168.10.3

255.255.255.0

192.168.10.1

PC-C

NIC

192.168.30.3

255.255.255.0

192.168.30.1

ISP

R3

Objectives
Part 1: Set Up the Topology and Initialize Devices
Part 2: Configure Devices and Verify Connectivity

Configure basic settings on PCs, routers, and switches.

Configure EIGRP routing on R1, ISP, and R3.

Part 3: Configure and Verify Extended Numbered and Named ACLs

Configure, apply, and verify a numbered extended ACL.

Configure, apply, and verify a named extended ACL.

Part 4: Modify and Verify Extended ACLs

Background / Scenario
Extended access control lists (ACLs) are extremely powerful. They offer a much greater degree of control
than standard ACLs as to the types of traffic that can be filtered, as well as where the traffic originated and
where it is going.
In this lab, you will set up filtering rules for two offices represented by R1 and R3. Management has
established some access policies between the LANs located at R1 and R3, which you must implement. The
ISP router between R1 and R3 does not have any ACLs placed on it. You would not be allowed any
administrative access to an ISP router as you can only control and manage your own equipment.
Note: The routers used with CCNA hands-on labs are Cisco 1941 Integrated Services Routers (ISRs) with
Cisco IOS Release 15.2(4)M3 (universalk9 image). The switches used are Cisco Catalyst 2960s with Cisco
IOS Release 15.0(2) (lanbasek9 image). Other routers, switches, and Cisco IOS versions can be used.

2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public.

Page 2 of 8

Lab Configuring and Verifying Extended ACLs

Depending on the model and Cisco IOS version, the commands available and output produced might vary
from what is shown in the labs. Refer to the Router Interface Summary Table at the end of the lab for the
correct interface identifiers.
Note: Make sure that the routers and switches have been erased and have no startup configurations. If you
are unsure, contact your instructor.

Required Resources

3 Routers (Cisco 1941 with Cisco IOS Release 15.2(4)M3 universal image or comparable)

2 Switches (Cisco 2960 with Cisco IOS Release 15.0(2) lanbasek9 image or comparable)

2 PCs (Windows 7, Vista, or XP with terminal emulation program, such as Tera Term)

Console cables to configure the Cisco IOS devices via the console ports

Ethernet and serial cables as shown in the topology

Part 1: Set Up the Topology and Initialize Devices

In Part 1, you will set up the network topology and clear any configurations if necessary.

Step 1: Cable the network as shown in the topology.

Step 2: Initialize and reload the routers and switches.

Part 2: Configure Devices and Verify Connectivity

In Part 2, you will configure basic settings on the routers, switches, and PCs. Refer to the Topology and
Addressing Table for device names and address information.

Step 1: Configure IP addresses on PC-A and PC-C.

Step 2: Configure basic settings on R1.
a. Disable DNS lookup.
b. Configure the device name as shown in the topology.
c.

Create a loopback interface on R1.

d. Configure interface IP addresses as shown in the Topology and Addressing Table.

e. Configure a privileged EXEC mode password of class.
f.

Assign a clock rate of 128000 to the S0/0/0 interface.

g. Assign cisco as the console and vty password and enable Telnet access. Configure logging
synchronous for both the console and vty lines.
h. Enable web access on R1 to simulate a web server with local authentication for user admin.
R1(config)# ip http server
R1(config)# ip http authentication local
R1(config)# username admin privilege 15 secret class

Step 3: Configure basic settings on ISP.

a. Configure the device name as shown in the topology.

2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public.

Page 3 of 8

Lab Configuring and Verifying Extended ACLs

b. Create the loopback interfaces on ISP.
c.

Configure interface IP addresses as shown in the Topology and Addressing Table.

d. Disable DNS lookup.

e. Assign class as the privileged EXEC mode password.
f.

Assign a clock rate of 128000 to the S0/0/1 interface.

g. Assign cisco as the console and vty password and enable Telnet access. Configure logging
synchronous for both console and vty lines.
h. Enable web access on the ISP. Use the same parameters as in Step 2h.

Step 4: Configure basic settings on R3.

a. Configure the device name as shown in the topology.
b. Create a loopback interface on R3.
c.

Configure interface IP addresses as shown in the Topology and Addressing Table.

d. Disable DNS lookup.

e. Assign class as the privileged EXEC mode password.
f.

Assign cisco as the console password and configure logging synchronous on the console line.

g. Enable SSH on R3.

R3(config)# ip domain-name cisco.com
R3(config)# crypto key generate rsa modulus 1024
R3(config)# line vty 0 4
R3(config-line)# login local
R3(config-line)# transport input ssh
h. Enable web access on R3. Use the same parameters as in Step 2h.

Step 5: (Optional) Configure basic settings on S1 and S3.

a. Configure the hostnames as shown in the topology.
b. Configure the management interface IP addresses as shown in the Topology and Addressing Table.
c.

Disable DNS lookup.

d. Configure a privileged EXEC mode password of class.

e. Configure a default gateway address.

Step 6: Configure EIGRP routing on R1, ISP, and R3.

a. Configure autonomous system (AS) number 10 and advertise all networks on R1, ISP, and R3. Disable
automatic summarization.
b. After configuring EIGRP on R1, ISP, and R3, verify that all routers have complete routing tables listing all
networks. Troubleshoot if this is not the case.

Step 7: Verify connectivity between devices.

Note: It is very important to verify connectivity before you configure and apply ACLs! Ensure that your
network is properly functioning before you start to filter out traffic.
a. From PC-A, ping PC-C and the loopback and serial interfaces on R3.

2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public.

Page 4 of 8

Lab Configuring and Verifying Extended ACLs

Were your pings successful?
b. From R1, ping PC-C and the loopback and serial interface on R3.
Were your pings successful?
c.

From PC-C, ping PC-A and the loopback and serial interface on R1.
Were your pings successful?

d. From R3, ping PC-A and the loopback and serial interface on R1.
Were your pings successful?
e. From PC-A, ping the loopback interfaces on the ISP router.
Were your pings successful?
f.

From PC-C, ping the loopback interfaces on the ISP router.

Were your pings successful?

g. Open a web browser on PC-A and go to http://209.165.200.225 on ISP. You will be prompted for a
username and password. Use admin for the username and class for the password. If you are prompted
to accept a signature, accept it. The router will load the Cisco Configuration Professional (CCP) Express
in a separate window. You may be prompted for a username and password. Use admin for the username
and class for the password.
h. Open a web browser on PC-C and go to http://10.1.1.1 on R1. You will be prompted for a username and
password. Use admin for username and class for the password. If you are prompted to accept a
signature, accept it. The router will load CCP Express in a separate window. You may be prompted for a
username and password. Use admin for the username and class for the password.

Part 3: Configure and Verify Extended Numbered and Named ACLs

Extended ACLs can filter traffic in many different ways. Extended ACLs can filter on source IP addresses,
source ports, destination IP addresses, destination ports, as well as various protocols and services.
Security policies are as follows:
1. Allow web traffic originating from the 192.168.10.0/24 network to go to any network.
2. Allow an SSH connection to the R3 serial interface from PC-A.
3. Allow users on 192.168.10.0.24 network access to 192.168.20.0/24 network.
4. Allow web traffic originating from the 192.168.30.0/24 network to access R1 via the web interface and the
209.165.200.224/27 network on ISP. The 192.168.30.0/24 network should NOT be allowed to access any
other network via the web.
In looking at the security policies listed above, you will need at least two ACLs to fulfill the security policies. A
best practice is to place extended ACLs as close to the source as possible. We will follow this practice for
these policies.

Step 1: Configure a numbered extended ACL on R1 for security policy numbers 1 and 2.
You will use a numbered extended ACL on R1. What are the ranges for extended ACLs?

a. Configure the ACL on R1. Use 100 for the ACL number.
R1(config)# access-list 100 remark Allow Web & SSH Access
R1(config)# access-list 100 permit tcp host 192.168.10.3 host 10.2.2.1 eq 22
R1(config)# access-list 100 permit tcp any any eq 80

2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public.

Page 5 of 8

Lab Configuring and Verifying Extended ACLs

What does the 80 signify in the command output listed above?

To what interface should ACL 100 be applied?

In what direction should ACL 100 be applied?

b. Apply ACL 100 to the S0/0/0 interface.

R1(config)# int s0/0/0
R1(config-if)# ip access-group 100 out
c.

Verify ACL 100.

1) Open up a web browser on PC-A, and access http://209.165.200.225 (the ISP router). It should be
successful; troubleshoot, if not.
2) Establish an SSH connection from PC-A to R3 using 10.2.2.1 for the IP address. Log in with admin
and class for your credentials. It should be successful; troubleshoot, if not.
3) From privileged EXEC mode prompt on R1, issue the show access-lists command.
R1# show access-lists
Extended IP access list 100
10 permit tcp host 192.168.10.3 host 10.2.2.1 eq 22 (22 matches)
20 permit tcp any any eq www (111 matches)
4) From the PC-A command prompt, issue a ping to 10.2.2.1. Explain your results?

Step 2: Configure a named extended ACL on R3 for security policy number 3.

a. Configure the policy on R3. Name the ACL WEB-POLICY.
R3(config)# ip access-list extended WEB-POLICY
R3(config-ext-nacl)# permit tcp 192.168.30.0 0.0.0.255 host 10.1.1.1 eq 80
R3(config-ext-nacl)# permit tcp 192.168.30.0 0.0.0.255 209.165.200.224
0.0.0.31 eq 80
b. Apply ACL WEB-POLICY to the S0/0/1 interface.
R3(config-ext-nacl)# int S0/0/1
R3(config-if)# ip access-group WEB-POLICY out
c.

Verify the ACL WEB-POLICY.

1) From R3 privileged EXEC mode command prompt, issue the show ip interface s0/0/1 command.
What, if any, is the name of the ACL?
In what direction is the ACL applied?

2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public.

Page 6 of 8

Lab Configuring and Verifying Extended ACLs

2) Open up a web browser on PC-C and access http://209.165.200.225 (the ISP router). It should be
successful; troubleshoot, if not.
3) From PC-C, open a web session to http://10.1.1.1 (R1). It should be successful; troubleshoot, if not.
4) From PC-C, open a web session to http://209.165.201.1 (ISP router). It should fail; troubleshoot, if
not.
5) From a PC-C command prompt, ping PC-A. What was your result and why?

Part 4: Modify and Verify Extended ACLs

Because of the ACLs applied on R1 and R3, no pings or any other kind of traffic is allowed between the LAN
networks on R1 and R3. Management has decided that all traffic between the 192.168.10.0/24 and
192.168.30.0/24 networks should be allowed. You must modify both ACLs on R1 and R3.

Step 1: Modify ACL 100 on R1.

a. From R1 privileged EXEC mode, issue the show access-lists command.
How many lines are there in this access list?
b. Enter global configuration mode and modify the ACL on R1.
R1(config)# ip access-list extended 100
R1(config-ext-nacl)# 30 permit ip 192.168.10.0 0.0.0.255 192.168.30.0
0.0.0.255
R1(config-ext-nacl)# end
c.

Issue the show access-lists command.

Where did the new line that you just added appear in ACL 100?

Step 2: Modify ACL WEB-POLICY on R3.

a. From R3 privileged EXEC mode, issue the show access-lists command.
How many lines are there in this access list?
b. Enter global configuration mode and modify the ACL on R3.
R3(config)# ip access-list extended WEB-POLICY
R3(config-ext-nacl)# 30 permit ip 192.168.30.0 0.0.0.255 192.168.10.0
0.0.0.255
R3(config-ext-nacl)# end
c.

Issue the show access-lists command to verify that the new line was added at the end of the ACL.

Step 3: Verify modified ACLs.

a. From PC-A, ping the IP address of PC-C. Were the pings successful?
b. From PC-C, ping the IP address of PC-A. Were the pings successful?
Why did the ACLs work immediately for the pings after you changed them?

2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public.

Page 7 of 8

Lab Configuring and Verifying Extended ACLs

Reflection
1. Why is careful planning and testing of ACLs required?

2. Which type of ACL is better: standard or extended?

3. Why are EIGRP hello packets and routing updates not blocked by the implicit deny any access control entry
(ACE) or ACL statement of the ACLs applied to R1 and R3?

Router Interface Summary Table

Router Interface Summary
Router Model

Ethernet Interface #1

Ethernet Interface #2

Serial Interface #1

Serial Interface #2

1800

Fast Ethernet 0/0

(F0/0)

Fast Ethernet 0/1

(F0/1)

Serial 0/0/0 (S0/0/0)

Serial 0/0/1 (S0/0/1)

1900

Gigabit Ethernet 0/0

(G0/0)

Gigabit Ethernet 0/1

(G0/1)

Serial 0/0/0 (S0/0/0)

Serial 0/0/1 (S0/0/1)

2801

Fast Ethernet 0/0

(F0/0)

Fast Ethernet 0/1

(F0/1)

Serial 0/1/0 (S0/1/0)

Serial 0/1/1 (S0/1/1)

2811

Fast Ethernet 0/0

(F0/0)

Fast Ethernet 0/1

(F0/1)

Serial 0/0/0 (S0/0/0)

Serial 0/0/1 (S0/0/1)

2900

Gigabit Ethernet 0/0

(G0/0)

Gigabit Ethernet 0/1

(G0/1)

Serial 0/0/0 (S0/0/0)

Serial 0/0/1 (S0/0/1)

Note: To find out how the router is configured, look at the interfaces to identify the type of router and how many
interfaces the router has. There is no way to effectively list all the combinations of configurations for each router
class. This table includes identifiers for the possible combinations of Ethernet and Serial interfaces in the device.
The table does not include any other type of interface, even though a specific router may contain one. An
example of this might be an ISDN BRI interface. The string in parenthesis is the legal abbreviation that can be
used in Cisco IOS commands to represent the interface.

2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public.

Page 8 of 8