Scribd
Upload
720 views

TTSAT CBLM Fabricating Formworks

The document provides information on competency-based learning materials for carpentry. It details how to use the learning module on fabricating formworks, which includes preparing materials and tools, laying out and cutting form sheeting and stiffeners, and assembling form panels.

Uploaded by

Moore Daham
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
720 views

TTSAT CBLM Fabricating Formworks

The document provides information on competency-based learning materials for carpentry. It details how to use the learning module on fabricating formworks, which includes preparing materials and tools, laying out and cutting form sheeting and stiffeners, and assembling form panels.

Uploaded by

Moore Daham
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 7

COMPETENCY-BASED LEARNING MATERIAL

Sector:

CONSTRUCTION

Qualification Title:

CARPENTRY NC II

Unit of Competency:

FABRICATE FORMWORKS

Module Title:

FABRICATING FORMWORKS

Technical Education and Skills Development Authority


TAwi-Tawi School of Arts and Trades Pag asa,
Bongao, Tawi-Tawi

HOW TO USE THIS COMPETENCY BASED LEARNING


MATERIAL
Carpentry NC
II
TTSAT QA
SYSTEM

Fabricating
Formworks

Date
Developed:
Nov., 2016
Developed by:
Mahmur I.
Daham

Document No.
Issued by:

Revision #
____

Page 1 of 7

Welcome to the module in fabricating form works. This module contains


training materials and activities for you to complete.
You are required to go through a series of learning activities in order to
complete each learning outcome of the module. In each learning outcome are
Information Sheets, Self-Checks, Operation Sheets and Job Sheets. Follow these
activities on your own. If you have questions, don't hesitate to ask your facilitator
for assistance.
The goal of this course is the development of practical skills. To gain these
skills, you must learn basic concepts and terminology. For the most part, you'll get
this information from the Information Sheets and multimedia materials
This module was prepared to help you achieve the required competency, in
"Fabricating Form works".
This will be the source of information for you to acquire knowledge and skills
in this particular competency independently and at your own pace, with minimum
supervision or help from your instructor.
Remember to:
Work through all the information and complete the activities in each
section.
Read information sheets and complete the self-check. Suggested references
are included to supplement the materials provided in this module.
Most probably your trainer will also be your supervisor or manager. He/she
is there to support you and show you the correct way to do things.
You will be given plenty of opportunity to ask questions and practice on the
job. Make sure you practice your new skills during regular work shifts. This way
you will improve both your speed and memory and also your confidence.
Use the Self-checks, Operation Sheets or Job Sheets at the end of each
section to test your own progress.
When you feel confident that you have had sufficient practice, ask your
Trainer to evaluate you. The results of your assessment will be recorded in your
Progress Chart and Accomplishment Chart.
UNIT OF COMPETENCY
: FABRICATE FORMWORKS
MODULE TITLE

FABRICATING FORM WORKS

Carpentry NC
II
TTSAT QA
SYSTEM

Fabricating
Formworks

Date
Developed:
Nov., 2016
Developed by:
Mahmur I.
Daham

Document No.
Issued by:

Revision #
____

Page 2 of 7

MODULE DESCRIPTOR

This module covers the knowledge, skills


and attitude in selecting and preparing
materials,
tools
and
equipment
for
fabricating form works, layingout, cutting to
dimensions of form sheating and stiffeners
and assembling form panels.

NOMINAL DURATION

40 hrs.

CERTIFICATE LEVEL

NATIONAL CERTIFICATE LEVEL II

PREREQUISITE
:
SUMMARY OF LEARNING OUTCOMES:
Upon completion of this module, the trainee/student must be able to:
LO 1. Prepare materials, tools and equipment for fabricating form works
according to job requirements
LO 2. Lay-out and cut to dimension of form sheating and stiffeners
LO 3. Assemble form panels

ASSESSMENT CRITERIA:
1. Plans and details are correctly interpreted and identified according to job
requirements
2. Materials, tools and equipment are identified consistent with job
requirements
3. Materials and tools are properly stored and freed from defects.
4. Appropriate PPE are selected according to job requirements.
5. Form sheating and stiffeners are measured and marked according to job
specifications
6. Form sheating and stiffeners are laid out and cut with tolerances of 3
mm for all measurements and squareness
7. Appropriate PPE is used according to job requirements
Carpentry NC
II
TTSAT QA
SYSTEM

Fabricating
Formworks

Date
Developed:
Nov., 2016
Developed by:
Mahmur I.
Daham

Document No.
Issued by:

Revision #
____

Page 3 of 7

8. Form panels and stiffeners are laid-out for pre-assembly


9. Form panels and stiffeners are pre-assembled
10. Form panels and stiffeners are checked for squareness according to
job requirements
11.

Form panels and stiffeners are assembled

12. Appropriate PPE is used according to job requirements and safety


regulations
13. Unexpected situations are responded to in line with company rules
and regulations
LEARNING OUTCOME NO. 1

1.
2.
3.
4.

Prepare materials, tools and


equipment for fabricating
formworks

CONTENTS:
Tools, materials and equipment for fabricating formworks
Materials estimates
Mechanical properties of lumber
Economic use of materials
ASSESSMENT CRITERIA
Plans and details are correctly interpreted and identified according to job
requirements
Materials, tools and equipment are identified consistent with job
requirements
Materials and tools are properly stored and freed from defects.
Appropriate PPE are selected according to job requirements.

Carpentry NC
II
TTSAT QA
SYSTEM

Fabricating
Formworks

Date
Developed:
Nov., 2016
Developed by:
Mahmur I.
Daham

Document No.
Issued by:

Revision #
____

Page 4 of 7

CONDITIONS:
You must be provided with the following:
WORKPLACE LOCATION
Personal Protective
TOOLS AND EQUIPMENT
Equipment
Claw Hammer

Portable Circular Saw


Pencil/Marking pen

Plan and working drawings


Pull-Push Rule

Lumber
Nylon String

Nails
Steel Square

Plywood
Try-square
Hand Saw

Chalk Line Manuals


TRAINING MATERIALS Related References
Leaning Packages
Bond paper
Ball pens
ASSESSMENT METHOD
Portfolio

Learning Experience
PREPARE MATERIALS, TOOLS AND EQUIPMENT FOR FABRICATING
FORM WORKS
Learning Activities

Special Instructions

Read Information Sheet No. 2.1-1


on Tools , materials and equipment
for fabricating formworks
Compare your
answer key

Answer Self-Check No. 2.1-1

answer

to

the

Read Information Sheet No. 2.1-2


on
Material
for
fabricating
formworks

Carpentry NC
II
TTSAT QA
SYSTEM

Fabricating
Formworks

Date
Developed:
Nov., 2016
Developed by:
Mahmur I.
Daham

Document No.
Issued by:

Revision #
____

Page 5 of 7

Answer Self-Check No. 2.1-2

Compare your
answer key

answer

to

the

Compare your
answer key

answer

to

the

Read Information Sheet No. 2.1-3


on Mechanical properties of
lumber
Read Information Sheet No. 2.1-4
on Economic use of materials
Answer Self-Check No. 2.1-4
Carpentry NC
II
SYSTEM

Fabricating
Formworks

Date
Developed:
Aug. 1, 2011
Developed by:
Glenn F.
Salandanan

Document
No.
Issued by:

Page 7 of 33

Revision #
____

INFORMATION SHEET NO. 2.1-1 TOOLS, MATERIALS AND


EQUIPMENT FOR FABRICATING FORMWORKS
Refer to module on Stake-out Building Lines, Information Sheet No. 1.1-4 on
Tools, Materials and Equipment in Staking-out Building Lines

Carpentry NC
II
TTSAT QA
SYSTEM

Fabricating
Formworks

Date
Developed:
Nov., 2016
Developed by:
Mahmur I.
Daham

Document No.
Issued by:

Revision #
____

Page 6 of 7

INFORMATION SHEET NO. 2.1-2 MATERIALS FOR FABRICATING


FORMWORKS
LEARNING OBJECTIVE:
Upon completing this section, you should be able to KNOW the
DIFFERENT MATERIALS for FABRICATING FORMWORKS and FORMWORK
DETAILS.
A. Materials used for Formwork
Materials used for the construction of concrete formwork range from
traditional materials such as wood, steel, aluminum, and plywood to
nontraditional materials such as fiberglass. Wood products are the most widely
used material for formwork.

Carpentry NC
II
TTSAT QA
SYSTEM

Fabricating
Formworks

Date
Developed:
Nov., 2016
Developed by:
Mahmur I.
Daham

Document No.
Issued by:

Revision #
____

Page 7 of 7

You might also like