Scribd
Upload
26 views

Nuclear Counter Lab

The document outlines a study to measure the ability of different materials to stop radiation transmission. Students use a Geiger counter and various radioactive sources to test alpha, beta, and gamma radiation shielding from materials like plastic, aluminum, and lead.

Uploaded by

Kevin Andino
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
26 views

Nuclear Counter Lab

The document outlines a study to measure the ability of different materials to stop radiation transmission. Students use a Geiger counter and various radioactive sources to test alpha, beta, and gamma radiation shielding from materials like plastic, aluminum, and lead.

Uploaded by

Kevin Andino
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Objective: Study the materials required to stop radiation from being transmitted.

State Standard: SCI.CP.7.7 2010


Setup
1) Turn the ST-160 nuclear lab station on, the button is on the back of the unit.
2) Set the voltage on the Geiger tube by pressing the H.V. button and push the up button until the
display reads 400.
3) Push the H.V. button again; the red LED should go out.
Measure the background radiation level
1)
2)
3)
4)

Obtain a timer from your teacher.


Push the count button and start the timer, let the counter run for 30 seconds.
Push stop after 30 seconds.
Record the counts and repeat 3 times and take the average.
a. Run 1__________________
b. Run 2__________________
c. Run 3__________________
d. Average_______________________

Testing Alpha particles


1) Get a set of sources from your teacher. These samples are radioactive but at a very low level
and are safe to handle.
2) Keep the sources at least 2 feet from the ST-160.
3) Insert the alpha source (Po-210), label down, into the plastic sample tray and place into the 3rd
slot from the top inside the test opening.
4) Conduct three sets of counts of 30 seconds each and average the results.
a. Run 1__________________
b. Run 2__________________
c. Run 3__________________
d. Average_______________________
5) Insert the 4 mil poly shield (#1) into the top slot and conduct 3 counts and average as before.
a. Run 1__________________
b. Run 2__________________
c. Run 3__________________
d. Average_______________________
6) How much radiation is reaching the detector through the shield?
a.

Charles Vanover 2012


[email protected]

________________________%

7) Remove the Poly shield (#1) and replace it with the .04 plastic shield (#4). Conduct another 3
counts and average.
a. Run 1__________________
b. Run 2__________________
c. Run 3__________________
d. Average_______________________
8) How much radiation is reaching the detector through the shield?
a.

________________________%

9) Remove the plastic shield and source and return them to their storage locations.
Testing Beta Particles
1. Insert the beta source (Sr-90), label down, into the plastic sample tray and place into the 3rd slot
from the top inside the test opening.
2. Conduct three sets of counts of 30 seconds each and average the results.
a. Run 1__________________
b. Run 2__________________
c. Run 3__________________
d. Average_______________________
3. Insert the.04 plastic shield (#4) into the top slot and conduct 3 counts and average as before.
a. Run 1__________________
b. Run 2__________________
c. Run 3__________________
d. Average_______________________
4. How much radiation is reaching the detector through the shield?
a.

________________________%

5. Remove the .04 plastic shield (#4) and replace it with the .09 aluminum shield (#7). Conduct
another 3 counts and average.
a. Run 1__________________
b. Run 2__________________
c. Run 3__________________
d. Average_______________________
6. How much radiation is reaching the detector through the shield?
a.

________________________%

7. Remove the .09 aluminum shield (#7) and replace it with the .032 lead shield (#8). Do three
counts and average as before.
e. Run 1__________________
f. Run 2__________________
g. Run 3__________________
h. Average_______________________
8. How much radiation is reaching the detector through the shield?
Charles Vanover 2012
[email protected]

a.

________________________%

9. Remove the shield and source and return them to the storage locations.
Testing a Gamma Source
1. Insert the gamma source (Co-60), label down, into the plastic sample tray and place into the 3rd
slot from the top inside the test opening.
2. Conduct three sets of counts of 30 seconds each and average the results.
a. Run 1__________________
b. Run 2__________________
c. Run 3__________________
d. Average_______________________
3. Insert the.025 aluminum shield (#5) into the top slot and conduct 3 counts and average as
before.
a. Run 1__________________
b. Run 2__________________
c. Run 3__________________
d. Average_______________________
4. How much radiation is reaching the detector through the shield?
a.

________________________%

5. Remove the .025 aluminum shield (#5) and replace it with the .032 lead shield (#8). Conduct
another 3 counts and average.
a. Run 1__________________
b. Run 2__________________
c. Run 3__________________
d. Average_______________________
6. How much radiation is reaching the detector through the shield?
a.

________________________%

7. Remove the .032 lead shield (#8) and replace it with the .25 lead shield (#11). Do three counts
and average as before.
a. Run 1__________________
b. Run 2__________________
c. Run 3__________________
d. Average_______________________
8. How much radiation is reaching the detector through the shield?
a.

________________________%

9. Remove the shield and source and return them to the storage locations.

Charles Vanover 2012


[email protected]

Analysis
1) What particle was the easiest to stop?
______________________________________________________________________________
______________________________________________________________________________
2) Which source was the most active? How can you tell?
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
3) Which source was the hardest to stop?
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
4) How would you protect yourself if you had to go into an environment that was contaminated
with alpha emitting radiation?
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________

Charles Vanover 2012


[email protected]

You might also like