Scribd
Upload
265 views2 pages

TDS - Masterseal 135

This document provides information about a two component, semi elastic, high solids epoxy polyurethane coating called MASTERSEAL 135. It describes the product's uses, advantages, packaging, properties, surface preparation instructions, application methods, and safety precautions.

Uploaded by

Venkata Rao
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
265 views2 pages

TDS - Masterseal 135

This document provides information about a two component, semi elastic, high solids epoxy polyurethane coating called MASTERSEAL 135. It describes the product's uses, advantages, packaging, properties, surface preparation instructions, application methods, and safety precautions.

Uploaded by

Venkata Rao
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

MASTERSEAL

135
Formerly Vencoat E 760 BS
Protective, decorative high performance
coating system for concrete
Description
Two component, semi elastic, high solids epoxy
polyurethane coating. Suitable for the internal and external
waterproofing and protection of concrete structures.

Primary uses

Elastomeric waterproof coating for concrete civil


structures: bridges, dams, viaducts, etc.
Coating for pipelines, collecting basins, water purification
plants and sewerages.

Advantages

Good chemical resistance against dilute acid and


alkaline solutions as well as mineral oils.
Good elasticity suitable to withstand micro-fissures of
concrete.
Good crack resistance.
Excellent resistance in heavy industrial and marine
environments.
Good UV resistance.

Packaging
MASTERSEAL 135 is available in 20 litre units.

Typical properties*
Solids by volume:
Specific gravity:
Thickness:
Theoretical coverage:
Theoretical consumption:
Number of coats:
Thinner:
Pot life:
Colour:
Appearance:
Shelf life:
Application temperature:
Service temperature:
Recoating interval minimum
Maximum
Hard dry:
Full curing:
Tensile strength DIN 53504:
Resistance against crack prop.
DIN 53515:
Extensibility DIN 53504:
Adhesion to concrete, ASTM D
4541:

88 2%
1.30 0.05 kg/l
400 m
2.2 m/l
590 g/m
2
7150 0023
2 hours at +20C
RAL colours
smooth, semi gloss
18 months (+5C to +35C)
from +5C to +35C
from -20C to +70C
12 hours at +20C
72 hours at +20C
24 hours at +20C
7 days at +20C
3.5N/mm
6N/mm
> 110%
3.5N/mm (concrete failure)

Surface preparation
Substrates must be clean and free from contaminants that
could impair adhesion. Concrete should be at least 28 days
old and should be subjected to light grit or hydro blasting to
remove laitance and expose blow holes and other surface
defects.
Defects should be made good with CONCRESIVE 2200
epoxy mortar or a suitable polymer/cement repair mortar
from the EMACO range.
The surface should be dry when making repairs with
CONCRESIVE 2200.
The use of MASTERTOP PRIMER 2 is recommended as a
primer and surface sealer.
Tightly bound resinous coatings must be roughened prior to
overcoating by grit blasting or disc sanding. Consult your
applicator or Degussa representative for specific primer

recommendations based on the polymer type of the previous


coating.
Alternative primers may be recommended for various
applications, including when 135 is to be applied over an
existing coating or when anti-carbonation and chloride ion
diffusion properties are required to be enhanced.
Consult your applicator or Degussa representative for
specific recommendations.
Mixing:
MASTERSEAL 135 is a two component product. Stir both
components separately, before pouring the hardener into the
base and mixing thoroughly, until a uniform colour is
obtained.
Components are pre weighed and the entire contents of
each pack should normally be used. If full pack usage is
impractical within pot-life, the following mixing ratios apply.
mixing ratio
Component A - base
Component B - hardener

by weight
75
25

Note
Field service, where provided, does not constitute
supervisory responsibility. For additional information contact
your local Degussa representative.
Degussa reserves the right to have the true cause of any
difficulty determined by accepted test methods.

Quality and care


All products originating from Degussa UAE facility are
manufactured under a management system independently
certified to conform to the requirements of the quality,
environmental and occupational health & safety standards
ISO 9001, ISO 14001 and OHSAS 18001.
04/96 Degussa-UAE revised 03/2005

by volume
66
34

MASTERSEAL 135 may be applied by brush, roller or spray


gun.
For cleaning equipment use Cleaning Solvent No. 2.

Spraying equipment
Airless spray
Nozzle orifice
Spray angle
Nozzle pressure

0.21-0.25 inch
50-80 degrees
150-200 bar

The product is ready to use. However, in certain application


conditions (low or high temperature) thinning with 5-10%
SOLVENT NO. 2.
Higher temperatures reduce the pot life of the mixed
product. In high ambient temperatures, pot-life may be
optimised by storage in an air conditioned room prior to use.

Safety precautions
As with all chemical products, care should be taken during
use and storage to avoid contact with eyes, mouth, skin and
foodstuffs. Treat splashes to eyes and skin immediately. If
accidentally ingested, seek medical attention. Reseal
containers after use. Use in well ventilated areas and avoid
inhalation. For further information, refer to material safety
data sheet.

Degussa Construction Chemicals UAE LLC


P.O. Box 37127, Dubai, UAE
Tel: +971 4 8851000

Fax: +971 4 8851002

www.degussa-cc.ae

e-mail: [email protected]

Whilst any information contained herein is true, accurate and


represents our best knowledge and experience, no warranty is given or
implied with any recommendations made by us, our representatives or
distributors, as the conditions of use and the competence of any labour
involved in the application are beyond our control.

Certificate No.
963680

As all Degussa technical datasheets are updated on a regular basis it is the user's responsibility to obtain the most recent issue.

Certificate No.
945787

Certificate No.
772556

You might also like