Installation Instructions

30-3001-994
Rev C.1

NetController II
Mounting
Screw

Andover Continuum
Power Supply Connector
I/O Bus
Connector

Third-Party
Power Supply Connector

Mounting
Screw

Cover

Mounting
Screw
BOTTOM PANEL

Cover Tab

See the Ethernet and Comm Port

Connections section later in this
document.

Cover Tab

Controller Installation (Model CX 9680 )

To install the controller, follow these steps:
1. Mount the controller on a standard DIN rail or to a panel
using screws. (See the Mounting Instructions and
Physical Dimensions sections of this document.)
Warning: Do not apply power to the controller until all
connections are secured. Read the Wiring Rules
section of this document before performing the
next steps.
2. Connect the I/O modules by simply plugging the modules
together or using a cable assembly to bridge the modules
together. (See the Connecting I/O Modules section of
this document.)

3. Connect the Ethernet and Communication Port connections based on your requirements. (See the Ethernet and
Comm Port Connections section of this document.)
4. Connect the power supply connector of the controller to an
Andover Continuum power supply or third-party UL Listed UL
294 or UL 603 power limited power supply. Access the PC
board and connect the battery. (See the DC Power and Battery
Backup Connections section.)
5. Apply power to the controller and I/O modules.
6. Configure the controller using the controllers embedded WebServer pages and CyberStation. For more information, refer to
the Related Documentation section at the end of this document.

2011 Schneider Electric, all rights reserved.

Mounting Instructions
DIN RAIL
2

PANEL
1

Physical Dimensions
222.3 mm
8.75

152.4 mm
6.00

63.5 mm
2.50

Wiring Rules
These modules are intended for installation
within the UL Listed enclosure 3P-UL-ENCL
for UL 294 and UL 1076.
For reliable operation, follow these wiring guidelines:
Never lay wires across the surface of a printed circuit board.
Use shielded wire.
Terminate the shield of the wires at one end of the run
only preferably at the end where your I/O module is located.
When stripping wire, be careful not to drop small pieces of wire
inside the cabinet.
Dont run your wiring in the same conduit with
AC power.
Dont run your wiring in the same conduit with your
output wiring.

Grounding the Controller

To insure proper operation of the controller, it must be connected to
a good earth ground. The connection must be made as close to the
module as possible.

Inspecting the Ground

Be sure to have your grounds inspected before you begin the installation
process.
Check your grounds as follows:
Inspect the building power distribution panel for earth-ground termination. If the ground termination is any of the following, it is not adequate
and must be corrected:
Does not exist
Is connected to a corroded or galvinized pipe
Is connected using a small gauge wire (less than 14 AWG).
Be sure your Andover Continuum cabinet is connected to the ground
with a copper conductor that terminates at the distribution panel. For
more information, see the Related Documentation section at the end
of this document.

Caution: Earth ground (

) must be connected to avoid

module damage.

DC Power and Battery Backup Connection

Andover Continuum Power Supply

Continuum
Power Supply

Power Supply Battery Backup

Battery Backup Connection
PS 120/240 AC 85-U, AC 50-U
and PS -48 DC 50-U

I/O

NetController II

I/O

NOTE: For more information on Andover

Continuum Power Supplies, see the Input
Power section of the Specifications topic.
BAT
(+)

24VDC
Battery
Supply

Third-Party UL Listed UL 294 or

UL 603 DC Power Supply

2-Conductor
Shielded Power Cable
from Power Supply

Third-Party
DC Power Supply
2-Conductor
Shielded
Power Cable

BAT
( )

NetController II

2-Conductor Shielded
data cable from
NetController

12VDC, 7AH
Battery

( )

( )

(+)

(+)

12VDC, 7AH
Battery

* The AC 85-U can only be used with

the NetController II for UL 294
applications.
** The AC 50-U and PS -48 DC 50-U
are not evaluated by UL and not UL
Listed to UL 1076.

I/O

I/O

I/O

I/O

I/O

NOTE: Only if you use a thirdparty DC power supply, input

power to the I/O modules must
be supplied externally.

DC Power and Battery Backup Connection (Continued)

Third-Party Power Supply
(DC Connections)

!
Use care when attaching power
wiring to these connectors.
They are not to be used as a strain relief.
The connectors cannot withstand
excessive bending or flexing.

+ 12 to 28VDC
VDC Return

AC POWER
24 VAC
20 VA
50/60 HZ
L

DC POWER
12 - 28 VDC
10 W

Third-Party Power Supply

(AC Connections)

90

50

Warning

DC Power and Battery Backup Connection (Continued)

Internal Battery Connection
During shipment the internal battery pack has been disconnected to prevent it from draining prior to installation.
NOTE: The indicator lamps and switches are connected to the circuit board via two thin ribbon cables. When you
lift the plastic housing do not remove the cables from their connectors.
To activate the battery:
1. Locate the plastic tabs on the bottom panel of the controller. (See illustration on the first page of this document.)
2. Using your fingers, gently depress the tabs while lifting the cover. Fold the cover back to access the main circuit board.
3. Connect the battery connector into the receptacle as shown in the illustration below.

Ribbon Cable
Connectors

Receptacle

_
+

Battery

Connecting the I/O Modules

Plugging Modules Together

FTT-10a (free topology transceiver technology)

The NetController II can directly connect to the I/O modules without using cables through a system of built-in plugs and jacks. All I/O modules
include two complementary module connectors. Creating a system is as
simple as physically plugging the modules together. (See the Horizontal
and Vertical Connection illustrations below).

NOTE: Prior to installing an I/O module network using the

FTT-10a bus, read the installation documentation from
the Echelon Corporation.

I/O Bus Connector

The I/O bus connector on the upper right side further distributes the
24 VDC input power and special I/O communication signals to all the
I/O modules. (See the I/O Bus Connector illustration below.)

Horizontal and Vertical Connections

In vertical extended systems, I/O modules may be located above or
below other modules. Connector cables bridge the I/O modules together.
Connection between the modules is one-to-one, straight-forward wiring.
(See the I/O Cable Wiring illustration below.)

LON Interfaces
The NetController II supports two types of Local Operating Network (LON) bus media:
RS-485 (ACC-LON) Default setting

Maximum Number of I/O modules

Continuum allows a maximum of 32 I/O modules per NetController II. There is also a limit based upon the capacity of the
power supply feeding the modules. (60 W maximum power)

Maximum Length of I/O Bus

The following are the cable length specifications:
RS-485 2000 ft. (610 m.)
FTT-10a 8858 ft. (2700 m.) double termination
1640 (500 m.) free topology

Termination of I/O Modules

An external 120 ohm terminating resistor is required at both
ends of the bus for proper termination. (See the I/O Cable
Wiring illustration that follows.)

Connecting the I/O Modules (Continued)

I/O Bus Connector Pins

Horizontal Connection
I/O Bus Connector
Power Supply

I/O Bus
Connector

5
4
3
2
1

PIN
5
4

24 VDC Return

3
2

Shield
Comm B

Comm A

Power Supply

I/O

Power Supply

Net
Controller II

NetController II

Vertical Connnection
5
4
3
2
1

I/O Cable Wiring

I/O

I/O

Function
+24 VDC

I/O Cable Wiring

5
4
3
2
1

NetController II

NetController II

I/O

I/O

Ethernet and Comm Port Connections

Bottom Panel

Port

COMM2

COMM1

Ethernet

Removable Plastic Cutout for

RJ-11 Modem Connector (Optional).
Not evaluated by UL.

COMM3

COMM4
Ethernet Cable w/
RJ-45 Connector

Connector Interface

Ethernet

RJ-45 (Ethernet 10/100 BASE-T)

Comm1

RS-232

ETHERNET

RS-485 (3-pin)
Service Port cable (Wireless Adapter or RoamIO2)
Comm2

Service Port cable (Wireless Adapter or RoamIO2)

RS-485 (4-pin)

Comm3

Service Port

RS-485 4-pin connector

RS-232
(Optional) Modem (RJ-11)

Comm4

RS-422 (L-Bus) or
Wireless Adapter or RoamIO2
(COMM1 and COMM2)

RS-485 (5-pin)

COMM 4*
RS-422 Connector
1

COMM 1 & 3*

COMM 3*
RJ-11 Modem Connector
(Optional)

RS-232 Connectors

RX+ (IN+)
TXD
DSR
RD
Ground
RTS
DCD
CTS
DTR

RX- (IN-)

Shield
TIP

TX+ (OUT+)
RING

TX- (OUT-)

COMM 4*

COMM 1*
RS-485 Connector

+
Shield

COMM 2*

RS-485 Connector

+
Shield

RS-485 Connector
(Jumpers convert
RS-422 to RS-485)

+
Shield

Earth Ground

+
* The Ethernet connector has been
evaluated by UL for UL294/UL1076.
All other communication connectors
have been evaluated by UL for
supplemental use.

Configuring the NetController II

(NOTE: Check with your system administrator for assistance.)
1. Disable the DHCP Services on your PC.

6. Log on using the default Andover Continuum user name and

password.

2. Disconnect your computer from the network and set your IP

address to 169.254.1.2 and your subnet mask to 255.255.0.0.

7. Enter relevant configuration parameters on the WebServer

Configuration web pages.

3. Using a CAT5 cable (straight-through or crossover), connect

the PC Ethernet port to the NetController II Ethernet port.

8. After entering the parameters, click the Commit Changes/Restart

Controller button on the WebServer page. (Restore the PC, and
connect the NetController II to the network when it reboots.)

4. Run your web browser, then go to URL: http://169.254.1.1 to

display the Andover Continuum Embedded WebServer page in the
NetController II.

For more information, please see the Related Documentation section

at the end of this document.

5. Select Controller Configuration from the WebServer page.

Specifications
Dimensions
8.75 W x 6.00 L x 2.5 H (222.3 x 152.4 x 63.5 mm)
Weight
1.5 lbs. (0.68 kg)
Enclosure Type
UL open class, flammability rating of UL94-5V, IP 10
Mounting
DIN rail or wall mount using attached fasteners. Andover
Continuum UL Listed enclosure model 3P-UL-ENCL is available
for UL 294 and UL 1076.
Operating Environment
Temperature: 32o to 122o F (0o to 50o C)
Humidity: 10 to 90% RH, non-condensing
Input Power
Andover Continuum Power Supplies:
PS 120/240 AC 85 (not evaluated by UL)
PS 120/240 AC 85-U (AC 85-U can only be used for UL 294)
Third Party Power Supply:
1228VDC @ 10W
24VAC @ 20VA, 50/60 Hz.
Internal Battery
NiMH, 3.6 VDC, 800 mAh
Real Time Clock
Battery-backed by UPS and internal battery.
Comm. Error Checking
International Standard CRC 16.
Ethernet LAN Interface
10/100 Ethernet: Ethernet cable with RJ-45 connector.
Serial Comm. Interface
Four programmable ports, software configurable as printer, modem,
wireless adapter, ROAM I/O, or third-party system. Infinet can be
configured on Ports 1 and 2.
Comm1: RS-232, RS-485, Service Port
Comm2: Service Port, RS-485
Comm3: RS-232, (optional) Modem (RJ-11 connector)
Comm4: RS-422 (L-Bus) or RS-485
Serial Comm. Speed
Comm1: Baud rates up to 38.4 K for RS-232 mode.
Comm3: Baud rates up to 38.4 K when configured for RS-232 or

internal modem.
Infinet Bus Length
4,000 ft (1,220m) standard for Infinet using approved shielded, twisted
pair, low capacitance cable. InfiLink module allows extensions to longer
distances.
I/O Bus
ACC-LON communications. Choice of bus media, RS-485 or
FTT-10A.
RS-485 Bus
Comm. Speed: 39K baud
Bus Length:
2,000 ft. (610m)
Bus Media:
Shielded, twisted pair cable. 120 ohm termination
required at both ends of the ACC-LON network
(when modules are mounted remotely).
FTT-10A Bus
Comm Speed: 78K baud
Bus Length:
Up to 8858 ft. (2700m) bus topology
Up to 1640 ft. (500m) free topology. Repeater required
for longer distances.
Bus Media:
Refer to Echelon FTT-10A free topology documentation
Connections
Power: 5-position plug-in connector on left side of module for
direct connection to Continuum power supply module.
3-position connector on left side of module for connection to a
third-party power supply module.
I/O Bus: 5-position plug-in connector on right side of module for
direct connection of up to 32 I/O modules.
Ethernet: RJ-45 connector for 10/100 Ethernet.
Printer: RJ-45
Modem: RJ-11 Connector
Status Indicator LEDs
System: Power, CPU, Error
Comm1: TD, RD, DCD, DTR
Comm2: TD, RD
Comm3/Modem: TD, RD, DCD, DTR, MODEM
Comm4: TD, RD
I/O Bus: Status
Ethernet: ACT/LINK, 10/100 Mbps
Push Button Switches
Clear Memory: RESET/Clear Memory
Reset IP Address: (On PC board) Resets Network address settings in
flash memory and restores all non-volatile settings to
factory defaults.

Regulatory Notices
Federal Communications Commission
FCC Rules and Regulations CFR 47, Part 15, Class A
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
Complies with FCC Part 68 Rules (when optional modem is installed).
FCC Registration Number: AU7NMOIBMT5656R REN Number: 0.1B
Caution: The user that changes or makes modifications not expressly approved by Schneider Electric for compliance could void the users authority to operate the equipment.

Industry Canada
ICES-003
This is a Class A digital device that meets all requirements of the Canadian Interference Causing Equipment Regulations.

CE - Compliance to European Union (EU)

89/336/EEC - EMC Directive
This equipment complies with the rules of the Official Journal of the European Union specified in the EMC directive
89/336/EEC governing the Self Declaration of the CE Marking for the European Union.

C-Tick (Australian Communications Authority (ACA))

AS/NZS 3548
This equipment carries the C-Tick label and complies with EMC and radio communications regulations of the Australian Communications Authority (ACA), governing the Australian and New Zealand (AS/NZS) communities.

WEEE - Directive of the European Union (EU)

This equipment and its packaging carry the waste of electrical and electronic equipment (WEEE) label, in compliance with European Union (EU)
Directive 2002/96/EC, governing the disposal and recycling of electrical and electronic equipment in the European community.

UL 916 Listed product for the United States and Canada, Access Control Equipment

UL 294 (Access Control System Unit Subassemblies for the United States) and UL 1076 (Proprietary
Burglar Alarm System Unit Subassemblies for the United States) and C22.2 No. 205-M1983 (Signal
Equpment for Canada)
Note: Refer to the UL Listed Access Control Propietary Burglar Alarm System installation manual (the UL 294 Access Control and UL
1076 Proprietary Burglar Alarm Systems Reference 30-3001-504) for specific wiring, operation, and compatibility information.

Related Documentation
The following related documentation provides more information on Andover Continuum products. These
documents are neither required nor evaluated by Underwriters Laboratories (UL) for UL Listings.

Document

Document Number

NetController II Operation and Technical Reference Guide

30-3001-995

Network Security Configuration Guide

30-3001-996

Andover Continuum CyberStation HVAC Essentials Guide

30-3001-1000

Andover Continuum CyberStation online help

Schneider Electric
One High Street
North Andover, MA 01845
(978) 975-9600
Fax: (978) 975-9782
http://www.schneider-electric.com/buildings