Scribd
Upload
170 views

Codeline Drawing 80S30 Non Coded

RO pressure vessel dimension details

Uploaded by

Darren Ponichai
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
170 views

Codeline Drawing 80S30 Non Coded

RO pressure vessel dimension details

Uploaded by

Darren Ponichai
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

DWG

PART
QTY
REF
NUMBER

Dash
L
P
S
Length IN(MM) IN(MM) IN(MM)
DESCRIPTION

MATERIAL

-1

59.15
(1502)

47
(1194)

23X1
(588)

Filament Wound Epoxy/Glass


composites - Head locking grooves
integrally wound in place.

-2

99.15
(2518)

87
(2210)

56X1
(1422)

(31)

CF3M *

-3

139.15
(3534)

127
(3226)

80X1
(2032)

(37)

-4

179.15
(4550)

167
(4242)

64X2
(1626)

(43)

-5

219.15
(5566)

207
(5258)

78X2
(1981)

106

-6

259.15
(6582)

247
(6274)

92X2
(2337)

119

-7

299.15
(7598)

287
(7290)

106X2
(2692)

130

-8

339.15
(8614)

327
(8306)

120X2
(3048)

142

SHELL
1
2
3

SHELL

ORDER
A/R SECTION
A/R

F/C Port
F/C Port Seal

Ethylene Propylene .

HEAD - NON CODED


4

96243

96000

Elliptical Head Assy. Engineering Thermoplastic.


Head Seal

Ethylene Propylene - O - Ring

HEAD INTERLOCK
6

47336

Approx
Weight
LB(KG)**
56

Quick Release Spiral


316 Stainless Steel.
Ring
VESSEL SUPPORT

2+

52169

Saddle

2+

45042

Strap Assy.

304 Stainless Steel-PVC Cushion.

46265

Strap screw.

5/16-18 UNC, 18-8 Stainless Steel.

Engineering Thermoplastic.

ELEMENT INTERFACE
10

A/R

Adapter

Engineering Thermoplastic.

11

52245

Adapter seal

Ethylene Propylene - O - Ring

12

A/R

PWT Seal

Ethylene Propylene - O - Ring

13

97014

Thrust Cone

Engineering Thermoplastic.

+ 3 each furnished with length code 4,5,6,7 & 8.

(25)
69
81
94

(48)
(54)
(59)
(64)

RATING:
DESIGN PRESSURE...300 PSIG at 190F
(2.1 MPa at 88C)
MIN. OPERATING TEMP.........20F
(-7C)
FACTORY TEST PRESSURE...450 PSIG
(3.1 MPa)
QUALIFICATION PRESSURE .....1800 PSI
(12.4 MPa)
INTENDED USE:
The CodeLine 80S30 Non Coded Fiberglass RO Pressure
Vessel is designed for continuous, long term use as a
housing for reverse osmosis membrane elements to desalt
typical brackish waters at pressures up to 300 psi. Any
make of eight-inch nominal diameter spiral-wound
element is easily accommodated; the appropriate
interfacing hardware for the element specified is
furnished with the vessel.
The Shell of CodeLine 80S30 Non Coded vessel is
designed in accordance with the engineering standards of
the Boiler and Pressure Vessel Code of the American
Society of Mechanical Engineers (ASME) as per Section
X.
The CodeLine 80S30 Non Coded vessel must be installed
operated and maintained in accordance with the listed
precautions and good industrial practice to assure safe
operation over a long service life.
The high performance Filament wound FRP shell must be
allowed to expand under pressure; undue restraint at
support points or piping connections can cause leaks to
develop in the shell. This side-ported vessel requires
special precautions in mounting and connection to piping
so that the vessel will not be subjected to excessive stress
due to bending moments acting at the side openings in the
fiberglass shell. The end closure, incorporating close
fitting, interlocking metal components, must be kept dry
and free of corrosion; deterioration can lead to
catastrophic mechanical failure of the head.
Pentair will assist the purchaser in determining the
suitability of this standard vessel for their specific
operating conditions. The final determination however,
including evaluation of the standard material of
construction for compatibility with the specific corrosive
environment, shall be the responsibility of the purchaser.
Alternate materials with enhanced corrosion resistance are
available on special order.

PRECAUTIONS:
DOread, understand and follow all instructions; failure to
take every precaution will void warranty and may result in
vessel failure
DOmount the shell on horizontal members at span S
using compliant vessel supports furnished; Shim saddles if
required. Tighten hold down straps just snug
DOalign and center side ports with the manifold header.
Correct, causes of misalignment in a row of vessels
connected to the same header
DOuse flexible type IPS grooved-end pipe couplings, at
side ports; allow full, 0.125 inch gap between port and
piping, and position piping to maximize flexibility of
connection.
DOprovide flexibility in, and support for piping manifolds
so that vessel can grow in length under pressure without
undue restraint; provide additional flexible joints in large
pipes leading to manifold header.
DOprovide overpressure protection for vessel set at not
more than 105% of design pressure
DOinspect end closures regularly; replace components that
have deteriorated and correct causes of corrosion
DO Lubricate seals sparingly, using nonpetroleum
Based lubricants, i.e. Parker Super O-lube,
Glycerin or suitable silicone based lubricants.
DO NOTwork on any component until first verifying that
pressure is relieved from vessel
DO NOTmake rigid piping connections to ports or clamp
vessel in any way that resists growth of fiberglass shell
under pressure;
***DIA = 0.015 in. (0.4mm) and
***L = 0.2 in. (6mm) for a length code 8 vessel
DO NOT hang piping manifolds from ports or use vessel in
any way to support other components
DO NOTtighten Permeate Port connection more than one
turn past hand tight
DO NOT operate vessel without connecting both Permeate
Ports internally to complete set of elements or otherwise
plug ports internally so that external piping connection is
not subjected to feed pressure
DO NOTinstall Spacer on downstream end of vessel
DO NOToperate vessel without Thrust Cone installed
downstream
DO NOTpressurize vessel until double-checking to verify
that the Locking Ring is in place and fully seated.
DO NOToperate vessel at pressure and temperature in
excess of its rating.
DO NOToperate vessel with permeate pressure in excess of
125 psi at 190F (0.86 Mpa at 880 C).
DO NOTtolerate leaks or allow end closures to be routinely
wetted in any way
DO NOToperate outside the pH range 3-11.

ORDERING:
Using the chart below, please check the features you require
VESSEL LENGTH CODE please check one
MODEL 80S30 Non Coded  -1  -2  -3  -4  -5  -6  -7  -8
MEMBRANE BRAND AND MODEL


Please supply adapters for the following membrane brand and specific model
Brand_________________________ Model_______________________

CERTIFICATION REQUIRED


CE Marked Standard.

Certified by Pentair.

ADAPTER KITS
UP
STREAM

DOWN
STREAM

PERMEATE PORT CONFIGURATION:





Standard. 1 FNPT & 1.5 IPS GROOVED NORYL HEAD.


Optional .1 BSP F/JIS F Parallel Thread & 1.5 IPS GROOVED NORYL HEAD.

STRAP ASSEMBLY
 Standard SS304

 Optional SS316

 Optional SS316L

FEED/CONCENTRATE PORT SELECTION


Material of Construction  Standard CF3M  Optional Duplex SS (CD3MN)
 Optional Super Duplex SS (CD3MWCuN)
Configuration

 Standard - CF3M 1D5D


 Optional Multi ports :( Refer SPEC.SHEET/PM/1.5-3for Multi port selection)

Serial number end


Opposite end



PORT SIZE CODE
D

1 GROOVED END

2 GROOVED END

2 GROOVED END

Specifications are subject to change without notice.


For complete information on proper use of the vessel
Please refer to the 80S Series USERS GUIDE 94182.

DWG. NO. 99172-N,

Pentair

PAGE 2 OF 2.

CODELINE BODY LABELS ARE PLACED AT


90 TO SERIAL NUMBER END AND AT 270
ON THE OPPOSITE SIDE END

You might also like