Scribd
Upload
21 views

In Unit1, 2 &3.: ON OFF

This document contains a class test for a 5th semester electrical and electronics engineering course on linear integrated circuits and applications. The test contains 3 questions with multiple parts each. Question 1 covers 555 timer circuits, IC voltage regulators, and duty cycle. Question 2 covers transistor transition times, fixed bias binary circuits, and maximum reverse saturation currents. Question 3 covers stable states, current sweep generators, Schmitt trigger design, monostable multivibrator waveforms, clamping circuit theorems, and calculating component values for a 500 microsecond monostable pulse.

Uploaded by

Rahul Pandey
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
21 views

In Unit1, 2 &3.: ON OFF

This document contains a class test for a 5th semester electrical and electronics engineering course on linear integrated circuits and applications. The test contains 3 questions with multiple parts each. Question 1 covers 555 timer circuits, IC voltage regulators, and duty cycle. Question 2 covers transistor transition times, fixed bias binary circuits, and maximum reverse saturation currents. Question 3 covers stable states, current sweep generators, Schmitt trigger design, monostable multivibrator waveforms, clamping circuit theorems, and calculating component values for a 500 microsecond monostable pulse.

Uploaded by

Rahul Pandey
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

Shri Shankaracharya Techanical Campus,Junwani, Bhilai.

B.E (ELECTRICAL& ELECTRONICS ENGINEERING)


CLASS TEST- II (Section- B)
th

5 SEMESTER, SESSION 2013-14


LINEAR INTEGRATED CIRCUITS & APPLICATIONS
Max Marks: 40
Times: 2Hours

-------------------------------------------------------------------------------------------------Note: - Part (a) is compulsory of each unit. Attempt any two from remaining three parts
in Unit1, 2 &3.

Q.1 (a) Why normally control terminal of 555 Timer is connected to ground through
0.01F by pass capacitor?
(2)
(b) List the important features of IC regulator. Draw the functional diagram of
IC 723 regulator and explain the function of each block.
(6)
(c) Describe a square wave generator circuit using 555 timer. Derive the
expression for TON and TOFF of the output waveform. Show that it is
impossible to have a duty cycle of 50% or less in such configuration. Suggest
a modify circuit that will allow you to obtain adjustable duty rectangular
wave.
(6)
(d) Explain how adjustable regulator IC works. Derive the expression for the
output voltage for LM 317 adjustable voltage regulator.
(6)
Q.2 (a) What do you mean by transition time and settling time?

(2)

(b) The Fixed bias binary uses n-p-n Si transistor with VCE (sat) = 0.5 V, VBE (sat) =
1V, ICBO = 10 mA at 25C and zero base to emitter voltage at cut off. The
circuit parameters are VCC = VBB = 6V, RC= 1.2k, R1=4.7 k, R2= 27 k.
Find:
(i) hFE(min) and stable state voltages and currents
(ii) Maximum reverse saturation currents .

Q.3 (a) What do you mean by Stable State?

(6)

UTP= 8V, LTP= 5V, VCC = 15 V, IC (sat) = 2 mA, hFE(min)=25. (6)


(d) Explain why monostable multivibrator gives single pulse. Draw

(6)
(2)

(b) Explain in detail current sweep generator along with neat


circuit diagram and waveforms.

(c) Design a Schmitt trigger circuit for the following specifications:

all the relative waveforms of monostable collector coupled

multivibrator.

(c) State and prove that clamping circuit theorem.

(5)
(5)

(d) Calculate the component values of a monostable multivibrator


developing an output pulse of 500 s duration. Assume
ICE(sat) = 5 mA , VCC = 10 V and -VBB = -4V.

(5)

You might also like