Previous | Next | Contents

ESDEP WG 15C
STRUCTURAL SYSTEMS: MISCELLANEOUS

Lecture 15C.3: Lattice Towers and Masts

OBJECTIVE/SCOPE
To describe typical lattice tower design problems; to introduce the background for the
load requirements; to emphasize the connection between basic functional
requirements and overall structural design; to explain the principles of the structural
analysis and the choice of structural details.
The lecture is confined to the detailed description of the design of one particular type
of tower, i.e. the high voltage transmission tower.
PREREQUISITES
None.
RELATED LECTURES
Lectures 4A: Protection: Corrosion
Lectures 6: Applied Stability
Lectures 7: Elements
Lectures 11: Connection Design: Static Loading
Lectures 13: Tubular Structures
SUMMARY
The common structural problems in the design of steel lattice towers for different
purposes are outlined.

The details of design are discussed in relation to a specific category of tower, the high
voltage transmission tower. The influence on the tower design of the user's functional
demands is explained and the background for the load assumptions is pointed out.
Different aspects affecting the overall design and the detailing are discussed and
problems connected with the structural analysis are explained. The effect of joint
eccentricities is discussed on the basis of a very common design example using angle
sections. The use of different detailing is mentioned.
The need for erection joints is stated and the types of joints are discussed. Corrosion
protection is briefly dealt with and its influence on the tower design is pointed out.
Tower foundations are not treated in this lecture.

1. INTRODUCTION
Towers or masts are built in order to fulfil the need for placing objects or persons at a
certain level above the ground. Typical examples are:
single towers for antennae, floodlight projectors or platforms for inspection,
supervision or tourist purposes.
systems of towers and wires serving transport purposes, such as ski lifts,
ropeways, or power transmission lines.
For all kinds of towers the designer should thoroughly study the user's functional
requirements in order to reach the best possible design for the particular structure. For
example, it is extremely important to keep the flexural and torsional rotations of an
antenna tower within narrow limits in order to ensure the proper functioning of the
equipment.
The characteristic dimension of a tower is its height. It is usually several times larger
than the horizontal dimensions. Frequently the area which may be occupied at ground
level is very limited and, thus, rather slender structures are commonly used.
Another characteristic feature is that a major part of the tower design load comes from
the wind force on the tower itself and its equipment, including wires suspended by the
tower. To provide the necessary flexural rigidity and, at the same time, keeping the
area exposed to the wind as small as possible, lattice structures are frequently
preferred to more compact 'solid' structures.

Bearing in mind these circumstances, it is not surprising to find that the design
problems are almost the same irrespective of the purpose to be served by the tower.
Typical design problems are:
establishment of load requirements.
consistency between loads and tower design.
establishment of overall design, including choice of number of tower legs.
consistency between overall design and detailing.
detailing with or without node eccentricities.
sectioning of structure for transport and erection.
In this lecture, towers for one particular purpose, i.e. the high voltage transmission
tower, have been selected for discussion.

2. HIGH VOLTAGE TRANSMISSION TOWERS

2.1 Background
The towers support one or more overhead lines serving the energy distribution. Most
frequently three-phase AC circuits are used requiring three live conductors each. To
provide safety against lightning, earthed conductors are placed at the top of the tower,
see Figures 1 and 2.

The live conductors are supported by insulators, the length of which increases with
increasing voltage of the circuit. To prevent short circuit between live and earthed
parts, including the surrounding environment, minimum mutual clearances are
prescribed.
Mechanically speaking, the conductors behave like wires whose sag between their
points of support depends on the temperature and the wire tension, the latter coming
from the external loads and the pre-tensioning of the conductor. As explained in

Section 2.4, the size of the tension forces in the conductor has a great effect upon the
tower design.
2.2 Types of Towers
An overhead transmission line connects two nodes of the power supply grid. The
route of the line has as few changes in direction as possible. Depending on their
position in the line various types of towers occur such as (a) suspension towers, (b)
angle suspension towers, (c) angle towers, (d) tension towers and, (e) terminal towers,
see Figure 1. Tension towers serve as rigid points able to prevent progressive collapse
of the entire line. They may be designed to serve also as angle towers.
To the above-mentioned types should be added special towers required at the
branching of two or more lines.
In Figure 2 examples of suspension tower designs from four European countries are
presented. Note similarities and mutual differences.
2.3 Functional Requirements
Before starting the design of a particular tower, a number of basic specifications are
established. They are:
a. voltage.
b. number of circuits.
c. type of conductors.
d. type of insulators.
e. possible future addition of new circuits.
f. tracing of transmission line.
g. selection of tower sites.
h. selection of rigid points.
i. selection of conductor configuration.
j. selection of height for each tower.

The tower designer should notice that the specifications reflect a number of choices.
However, the designer is rarely in a position to bring about desirable changes in these
specifications. Therefore, functional requirements are understood here as the electrical
requirements which guide the tower design after establishment of the basic
specifications.
The tower designer should be familiar with the main features of the different types of
insulators. In Figure 3 three types of insulators are shown. They are all hinged at the
tower crossarm or bridge.

Figure 4 shows the clearances guiding the shape of a typical suspension tower. The
clearances and angles, which naturally vary with the voltage, are embodied in national

regulations. Safety against lightning is provided by prescribing a maximum value of

the angle v. The maximum swing u of the insulators occurs at maximum load on the
conductor.

2.4 Loads on Towers, Loading Cases

The loads acting on a transmission tower are:
a. dead load of tower.
b. dead load from conductors and other equipment.

c. load from ice, rime or wet snow on conductors and equipment.

d. ice load, etc. on the tower itself
e. erection and maintenance loads.
f. wind load on tower.
g. wind load on conductors and equipment.
h. loads from conductor tensile forces.
i. damage forces.
j. earthquake forces.
It is essential to realize that the major part of the load arises from the conductors, and
that the conductors behave like chains able to resist only tensile forces. Consequently,
the dead load from the conductors is calculated by using the so-called weight span,
which may be considerably different from the wind span used in connection with the
wind load calculation, see Figure 5.

The average span length is usually chosen between 300 and 450 metres.
The occurrence of ice, etc. adds to the weight of the parts covered and it increases
their area exposed to the wind. Underestimation of these circumstances has frequently
led to damage and collapse. It is, therefore, very important to choose the design data
carefully. The size and distribution of the ice load depends on the climate and the local
conditions. The ice load is often taken as a uniformly distributed load on all spans. It
is, however, evident that different load intensities are likely to occur in neighbouring
spans. Such load differences produce longitudinal forces acting on the towers, i.e.
acting in the line direction.
The wind force is usually assumed to be acting horizontally. However, depending on
local conditions, a sloping direction may have to be considered. Also, different wind
directions (in the horizontal plane) must be taken into account for the conductors as

well as for the tower itself. The maximum wind velocity does not occur
simultaneously along the entire span and reduction coefficients are, therefore,
introduced in the calculation of the load transferred to the towers.
The tensile forces in the conductors act on the two faces of the tower in the line
direction(s). If they are balanced no longitudinal force acts on a tower suspending a
straight line. For angle towers they result in forces in the angle bisector plane, and for
terminal towers they cause heavy longitudinal forces. As the tensile forces vary with
the external loads, as previously mentioned, even suspension towers on a straight line
are affected by longitudinal forces. For all types of towers the risk of mechanical
failure of one or more of the conductors has to be considered.
The loads and loading cases to be considered in the design are usually laid down in
national regulations.
2.5 Overall Design and Truss Configuration
The outline of the tower is influenced by the user's functional requirements. However,
basically the same requirements may be met by quite different designs. In general, the
tower structure consists of three parts: the crossarms and/or bridges, the peaks, and the
tower body.
Statically speaking, the towers usually behave like cantilevers or frames, in some
cases with supplementary stays. For transmission lines with 100 kV voltage or more,
the use of steel lattice structures is nearly always found advantageous because they
are:
easily adaptable to any shape or height of tower.
easily divisible in sections suitable for transport and erection.
easy to repair, strengthen and extend.
durable when properly protected against corrosion.
By far the most common structure is a four-legged tower body cantilevering from the
foundation, see Figure 6. The advantages of this design are:

 the tower occupies a relatively small area at ground level.

two legs share the compression from both transverse and longitudinal loads.
the square or rectangular cross-section (four legs) is superior to a triangular
tower body (three legs) for resisting torsion.
the cross-section is very suitable for the use of angles, as the connections can
be made very simple.

The following remarks in this section relate mainly to a cantilever structure. However,
many features also apply to other tower designs.
For a cantilever structure, the tower legs are usually given a taper in both main
directions enabling the designer to choose the same structural section on a
considerable part of the tower height. The taper is also advantageous with regard to
the bracing, as it reduces the design forces (except for torsional loads).
The bracing of the tower faces is chosen either as a single lattice, a cross bracing or a
K-bracing, possibly with redundant members reducing the buckling length of the leg
members, for example see Figure 6. The choice of bracing depends on the size of the
load and the member lengths. The most common type is cross bracing. Its main
advantage is that the buckling length of the brace member in compression is
influenced positively by the brace member in tension, even with regard to deflection
perpendicular to the tower face.
Generally, the same type of bracing is chosen for all four tower body faces, most
frequently with a staggered arrangement of the nodes, see Figure 7. This arrangement
provides better space for the connections, and it may offer considerable advantage
with respect to the buckling load of the leg members. This advantage applies
especially to angle sections when used as shown in Figures 10 and 11, since it
diminishes the buckling length for buckling about the 'weak' axis v-v. For further
study on this matter see [1].

Irrespective of the type of bracing, the tower is generally equipped with horizontal
members at levels where leg taper changes. For staggered bracings these members are
necessary to 'turn' the leg forces. Torsional forces, mostly acting at crossarm bottom
levels, are distributed to the tower faces by means of horizontal bracings, see Figure 8.

Cross arms and earthwire peaks are, in principle, designed like the tower itself.
However, as the load on the cross arms rarely has an upward component, cross arms
are sometimes designed with two bottom chords and one upper chord and/or with
single lattice bracings in the non-horizontal faces.
2.6 Structural Analysis
Generally, the structural analysis is carried out on the basis of a few very rough
assumptions:
the tower structure behaves as a self-contained structure without support from
any of the conductors.
the tower is designed for static or quasi-static loads only.
These assumptions do not reflect the real behaviour of the total system, i.e. towers and
conductors, particularly well. However, they provide a basis from simple calculations
which have broadly led to satisfactory results.

Generally speaking, a tower is a space structure. It is frequently modelled as a set of

plane lattice structures, which are identical with the tower body planes together with
the planes of the cross arms and the horizontal bracings mentioned in Section 2.5.
In a simplified calculation a four-legged cantilevered structure is often assumed to
take the loads as follows:
a. centrally acting, vertical loads are equally distributed between the four legs.
b. bending moments in one of the main directions produce an equal compression in
the two legs of one side, and equal tension in the two legs of the other side. The shear
forces are resisted by the horizontal component of the leg forces and the brace forces
(thus, the leg taper has a significant influence on the design of the bracing).
c. torsional moments broadly produce shear forces in the tower body faces, i.e. in the
braces.
A classical analysis assuming hinges in all nodes leads to very simple calculations.
However, the effect of redundancies should be considered, especially concerning the
forces and moments in the brace members.
Although this approach is satisfactory in most cases attention must be drawn to the
function of redundant members, which in some cases may change the load distribution
considerably. In addition, the effect of fixed connections (as opposed to hinged
connections) must be considered, since they produce moments in the bracing
members. The effect of eccentricities in the joints should also be taken into account,
see Section 2.7.
Finally, the distribution of an eccentric horizontal load is studied. In Figure 9 the force
H is acting at the cross arm bottom level. Without horizontal bracing in the tower,
three tower body planes are affected by H. The deflections of the plane lattice
structures of the tower body deform the rectangle ABCD to a parallelogram
A B C D . By adding member AC or BD this deformation is restricted and all four
tower body planes participate in resisting the force H.

2.7 Detailing of Joints

The detailed design is governed by a number of factors influencing the structural costs
once the overall design has been chosen, such as:
simple and uniform design of connections.
simple shaping of structural components.
details allowing for easy transportation and erection.

 details allowing for proper corrosion protection.

As an introductory example of design and calculation, a segment of a four-legged
tower body is discussed, see Figure 10. All members are made of angle sections with
equal legs. The connections are all bolted without the use of gussets, except for a
spacer plate at the cross bracing interconnection. This very simple design requiring a
minimum of manufacturing work is attained by the choice and orientation of the leg
and brace member sections.
By choosing the design described above, some structural eccentricities have to be
accepted. They arise from the fact that the axes of gravity of the truss members do not
intersect at the theoretical nodes. According to the bending caused by the
eccentricities they may be classified as in-plane or out-of-plane eccentricities. In
Figure 11, the brace forces C and T meet at a distance e o from the axis of gravity. The
resultant force S produces two bending moments: Me = S eo and Mf=S e1.
These moments are distributed among the members meeting at the joint according to
their flexural stiffness, usually leaving the major part to the leg members. As z-z is the
'strong' axis of the leg section, a resultant moment vector along axis v-v will be
advantageous. This is achieved, when eo=-e1 . In this case C and T intersect
approximately at the middle of the leg of the section. Usually this situation is not fully
practicable without adding a gusset plate to the joint.
Additional eccentricity problems occur when the bolts are not placed on the axis of
gravity, especially when only one bolt is used in the connection (eccentricities e c and
et).
The out-of-plane eccentricity causing a torsional moment, V = H e2, acting on the leg
may be measured between the axes of gravity for the brace members (see Figure 11).
However, the torsional stiffness of the leg member may be so moderate - depending
on its support conditions - that V cannot be transferred by the leg and, consequently,
e2 must diminish. The latter causes bending out-of-plane in the brace members.
The leg joint shown in Figure 10 is a splice joint in which an eccentricity e 3 may
occur. In this case there is a change of leg section, or the gravity axis for the four (or
two) splice plates in common does not coincide with the axis of the leg(s). For legs in
compression the joint must be designed with some flexural rigidity to prevent
unwanted action as a hinge.
The joint eccentricities have to be carefully considered in the design. As the lower part
of the leg usually is somewhat oversized at the joint - this is, in fact, the reason for
changing leg section at the joint - a suitable model would be to consider the upper part

of the leg centrally loaded and thus, let the lower part resist the eccentricity moment.
The splice plates and the bolt connections must then be designed in accordance with
this model.
The bolted connections might easily be replaced by welded connections with no major
changes of the design. However, except for small structures, bolted connections are
generally preferred, as they offer the opportunity to assemble the structural parts
without damaging the corrosion protection, see Section 2.8.
This introductory example is very typical of the design with angle sections.
Nevertheless some additional comments should be added concerning the use of
gussets and multiple angle sections.
The use of gussets is shown in Figure 12. They provide better space for the bolts,
which may eliminate the in-plane eccentricities, and they allow for the use of double
angle sections. In the latter case out-of-plane eccentricities almost vanish.

For heavily loaded towers it might be suitable to choose double or even quadruple
angle sections for the legs. Figure 13 shows some possibilities.

Towers designed with other profiles than angles

In principle any of the commercially available sections could be used. However, they
have to compete with the angle sections as regards the variety of sections available
and the ease of designing and manufacturing simple connections. So far only flat bars,
round bars and tubes have been used, mostly with welded connections. The use is
limited to small size towers for the corrosion reasons mentioned above.
In other contexts, e.g. high rise TV towers, circular sections may be more interesting
because their better shape reduces wind action.
Construction joints and erection joints
The tower structure usually has to be subdivided into smaller sections for the sake of
corrosion protection, transportation and erection. Thus a number of joints which are
easy to assemble on the tower site, have to be arranged. Two main problems have to
be solved: the position and the detailing of the joints.
In Figure 14 two examples of the joint positions are shown. The framed structure is
divided into lattice structure bodies, each of which may be fully welded, and stays.
The cantilevered structure usually is subdivided into single leg and web members.

The two types of joints are lap (or splice) joints and butt plate joints. The former is
very suitable for angle sections. The latter is used for all sections, but is mostly used
for joints in round tube or bar sections. Figure 15 shows some examples of the two
types.

2.8 Corrosion Protection

Today, corrosion protection of steel lattice towers is almost synonymous with hotgalvanising, possibly with an additional coating. The process involves dipping the
structural components into a galvanic bath to apply a zinc layer, usually about
100 m thick.
No welding should be performed after galvanizing, as it damages the protection. The
maximum size of parts to be galvanized is limited by the size of the available galvanic
bath.

3. CONCLUDING SUMMARY
The overall design of a lattice tower is very closely connected with the user's
functional requirements. The requirements must be studied carefully.
A major part of the design loads on the tower results from the wind force on
tower and equipment.
The occurrence of an ice cover on the tower and equipment must be considered
in the design.
For towers supporting wires, differential loads in the wire direction must be
taken into account.
For systems of interconnected towers it must be considered that the collapse of
one tower may influence the stability of a neighbouring tower.
In most cases a cantilevered tower with four legs is preferred, as it offers
structural advantages and occupies a relatively small ground area.
The type of bracing greatly affects the stability of both legs and braces. Kbracings and/or staggered cross bracings are generally found advantageous.
Horizontal braces at certain levels of the tower add considerably to its torsional
rigidity.
Angle sections are widely used in towers with a square or rectangular base, as
they permit very simple connection design.
Both in-plane and out-of-plane eccentricities in the connections must be
considered.

 A proper, long lasting corrosion protection must be provided. The protection

method influences the structural design.

4. REFERENCES
[1] European Convention for Constructional Steelwork, ECCS, "Recommendations
for Angles in Lattice Transmission Towers", ECCS Technical Committee 8, Brussels
1985.
Recommendations concerning slenderness ratios and buckling curves from leg and
web members taking into account redundancies and eccentricities.

5. ADDITIONAL READING
1. Fischer, R. and Kiessling, F., "Freileitungen - Planung, Berechung,
Ausfhrung", Springer Verlag 1989 (In German)
Comprehensive treatment of all aspects on high-voltage transmission lines, i.e.
planning, conductors, insulators and other equipment, design and calculation of
towers, foundation, corrosion protection and erection.
2. International Electrotechnical Commission - Technical Committee No 11,
"Recommendations for Overhead Lines" (Draft, December 1988).
Recommendations for establishing design criteria and loadings.
3. Eurocode 1: "Basis of Design and Actions on Structures", CEN (in preparation)
Definition of wind action.
4. Eurocode 3: "Design of Steel Structures": ENV 1993-1-1: Part 1.1: General
rules and rules for buildings, CEN, 1992.
Previous | Next | Contents