Scribd
Upload
222 views

Hardness

This document introduces different hardness testing methods including Brinell, Vickers, and Rockwell hardness tests. It provides details on the principles, procedures, and limitations of each test. The Brinell test uses a hardened steel ball pressed into the material under a specified load. Vickers uses a diamond pyramid shaped indenter. Rockwell uses either a diamond cone or steel ball and measures indentation depth rather than size. Each test calculates hardness values using relationships involving the indenter geometry and applied load. The document also discusses relating hardness to other material properties like tensile strength and the importance of surface conditions and spacing between indentations.

Uploaded by

MoazMohdTrawneh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
222 views

Hardness

This document introduces different hardness testing methods including Brinell, Vickers, and Rockwell hardness tests. It provides details on the principles, procedures, and limitations of each test. The Brinell test uses a hardened steel ball pressed into the material under a specified load. Vickers uses a diamond pyramid shaped indenter. Rockwell uses either a diamond cone or steel ball and measures indentation depth rather than size. Each test calculates hardness values using relationships involving the indenter geometry and applied load. The document also discusses relating hardness to other material properties like tensile strength and the importance of surface conditions and spacing between indentations.

Uploaded by

MoazMohdTrawneh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

HARDNESS TESTING

Objective
To introduce the principles of indentation hardness testing, emphasizing the limitations
and significance of the results.

Introduction
Hardness is generally considered as resistance to penetration. The harder the materials, the
greater the resistance to penetration. Hardness is directly related to the mechanical properties
of the material. Factors influencing hardness include microstructure, grain size, strain
hardening, etc. Generally as hardness increases so does yield strength and ultimate tensile
strength (UTS), thus specifications often require the results of hardness tests rather than
tensile tests. The most popular methods are Brinell, Vickers and Rockwell hardness tests for
metals and alloys.

Brinell Test
In a standard Brinell test 10 mm diameter hardened steel ball is forced to penetrate the
material by 3000 kgf for steels and cast irons. The load and ball diameter selection is
important depending on the hardness of materials and 500 kgf is used for softer materials with
the same ball diameter. Keeping the ratio of load P to the square of diameter D2 constant (30
for steels and cast irons and 5 for soft metals and alloys), different load and ball diameter
combinations can be selected and used in Brinell hardness testing. The Brinell Hardness
Number (BHN) is obtained by dividing the applied force P, in kgf; by the curved surface area
of the indentation, which is actually a segment of sphere. The geometry of indentation is
given in Figure-1, and the hardness is determined according to the relationship,
BHN =

2P
D[ D ( D2 D2 )1/ 2 ]

where D is the diameter of the indenter ball and d is the average diameter of the indentation,
both in mm.
a =135

Figure-1: Geometry of deformation


under a Brinell hardness indenter.

Figure-2: Vickers hardness indentation.

Vickers Test
The Vickers hardness test is based on the same principle as the Brinell test, except the
indenter is a diamond pyramid with square base. The angle between the faces of pyramid is
1360 as shown in Figure-2. The Vickers Hardness Number (VHN) of materials is obtained by
dividing the applied force P, in kgf, by the surface of the pyramidal depression yielding the
relationship
VHN=

1.8544 P
d2

(in some sources VHN is cited as DPH)

where d is the average length of diagonals in mm. Due to the shape and hardness of indenter
the method is applicable to metals and alloys with wide variety of hardness. Test load is
selected between 1 and 120 kgf depending on the hardness of materials. It is also possible to
apply micro hardness testing by keeping the force between 5 grf and 2 kgf in Vickers scale.

Rockwell Test
In the Rockwell test, a diamond cone or a hard steel ball is employed as the indenter
depending on the hardness of materials. Diamond cone or Brale indenter with cone angle of
1200 is used to test hard materials and the balls of sizes between 1.6 mm (1/16") and 12.7 mm
(1/2") are used in testing softer materials. Rockwell tests differ from other indentation
hardness tests in that the depth of indentation determines the hardness rather than the
indentation size (see Figure-3). Therefore, surface condition of specimens is very important in
Rockwell testing because of its high dependency on the accuracy in indentation depth
measurements. In order to establish a reference position a minor load of 10 kgf. is first
applied, and the major load is then applied. Additional penetration due to major load is
measured and readings are obtained from a calibrated scale (dial) directly, which has a
maximum value of 100, depending on the depth of penetration. Most commonly used
Rockwell hardness scales are given in Table-l with typical applications. The hardness
numbers are designated HRX, where X indicates the scale used (i.e. 50 HRC for 50 points on
the C scale of dial). It should be noted that a Rockwell hardness number is meaningless unless
the scale is not specified.

HR = E-e

Figure-3: Increasing depth of penetration in the Rockwell test

Table-I: Commonly used Rockwell hardness scales.


Indenter Type
Major Load
Scale
Typical Applications
X
(kgf)
I

A
D
C

Diamond Brale
Diamond Brale
Diamond Brale

60
100
150

1/16" Diameter Ball

100

1/8" Diameter Ball

100

F
M
R

1/16" Diameter Ball


1/4" Diameter Ball
1/2" Diameter Ball

60
100
60

Tool Materials
Cast Irons, Sheet Steels
Hardened steels and cast irons, Ti
alloys
Annealed steels, Cu and Al
alloys
Al and Mg alloys, reinforced
polymers
Soft sintered products
Very soft metals, polymers
Very soft metals, polymers

Since the deformations caused by an indenter are of similar magnitude to those occurring
at the ultimate tensile strength in a tension test, some empirical relationships have been
established between hardness and engineering ultimate tensile strength of metals and alloys.
For example, for steels UTS can be roughly estimated from Brinell hardness as follows:

Equipment

UTS (in MPa) = 3.45 x BHN

Rockwell hardness tester


Brinell hardness tester
Microhardness (Vickers) tester
Different test specimens

Procedure

1. Determine the proper Rockwell hardness scale,


2. calibrate the Rockwell hardness tester,
3. take five readings per specimen,
4. Perform Brinell hardness
measurements on designated specimens (3 readings)
5. Using microhardness tester, determine the VHN at 0.20 mm distances from the
surface to the center of case carburized specimen, until the hardness remains unchanged.
6. Determine the core hardness of the carburized steel.

Analysis
Calculate the range and mean in hardness values for each test specimen which will be
considered in lab report.

Lab Report Requirements


1. Results
List hardness values of Rockwell and Brinell for each specimen.
List VHN versus distance from surface for carburized specimen.
Determine the effective carburizing depth that corresponds to 400 VHN
2. Discussion (only those indicated will be answered in the lab report)
1. How do the Rockwell and Brinell tests actually measure hardness? Give any
appropriate sketches and formulae. Are there any units involved? Describe the
procedure for the Rockwell test, explaining the reason for the pre-load.
2. What is the limitation on the thickness of specimens for a hardness test? Explain.
Calculate the minimum thickness for one specimen for the Rockwell test and one for
the Brinell test.
3. What are the limitations for distance from specimen edge to indentation and distance
between indentations? Explain why these limitations exist in both cases. .
4. What surface condition is necessary for Brinell, Rockwell and Vickers?
5. Why is the mean pressure (stress) under the indentor much greater than
the yield stress? How much greater is it?
6. What are the advantages of Vickers test against Brinell test?

References

1. Metals Handbook, 9th ed., Mechanical Testing, Vol. 8, 1990.


2. G. Dieter, Mechanical Metallurgy, S1 ed., Mc Graw Hill, 1986.
3. N. Dowling, Mechanical Behavior of Materials, Prentice Hall, 1993.
4. "An Evaluation of the Impression Test for Estimating the Tensile Properties
of Metallic Materials, "H.N. Jones, Journal of Testing and Evaluation, Vol. 20, pp. 403407, Nov. 1992.

You might also like