Foundation Engineering

CVL 4319

Chapter 6

Mat Foundations
Dr. Sari Abusharar
University of Palestine
Faculty of Applied Engineering and Urban Planning
Civil Engineering Department
1st Semester 2015-2016

Outline of Presentation

Introduction

Combined Footings

Common Types of Mat Foundations

Bearing Capacity of Mat Foundations

Differential Settlement of Mats

Field Settlement Observations for Mat Foundations

Compensated Foundation

Structural Design of Mat Foundations

Introduction
Under normal conditions, square and rectangular footings are
economical for supporting columns and walls. However, under
certain circumstances, it may be desirable to construct a footing that
supports a line of two or more columns. These footings are referred
to as combined footings. When more than one line of columns is
supported by a concrete slab, it is called a mat foundation.
Combined footings can be classified generally under the following
categories:
a. Rectangular combined footing
b. Trapezoidal combined footing
c. Strap footing
Mat foundations are generally used with soil that has a low bearing
capacity.
3

Rectangular combined footing

Trapezoidal combined footing

Strap footing

Rectangular Combined Footing

In several instances, the load to be carried by a column and the soil bearing
capacity are such that the standard spread footing design will require
extension of the column foundation beyond the property line. In such a case,
two or more columns can be supported on a single rectangular foundation.

Rectangular Combined Footing

If the net allowable soil pressure is known, the size of the foundation (LxB)
can be determined in the following manner:
Step (1): Determine the area of the foundation

Step (2): Determine the location of the resultant of the column loads.

Step (3): For a uniform distribution of soil pressure under the foundation, the
resultant of the column loads should pass through the centroid of
the foundation. Thus,
6

Rectangular Combined Footing

Step (4): Once the length L is determined, the value of L1 can be obtained as
follows:

Note that the magnitude of L2 will be known and depends on the location
of the property line.
Step (5): The width of the foundation is then

Rectangular Combined Footing

Trapezoidal Combined Footing

Trapezoidal combined footing (see Figure 6.2) is sometimes used as an
isolated spread foundation of columns carrying large loads where space is
tight.

Trapezoidal Combined Footing

The size of the foundation that will uniformly distribute pressure on the soil
can be obtained in the following manner:
Step (1): If the net allowable soil pressure is known, determine the area of
the foundation:
From Figure 6.2,
Step (2): Determine the location of the resultant for the column loads:

Step (3): From the property of a trapezoid,

centroid of the
foundation

Solve Eqs. (6.6) and (6.7) to obtain

B1 and B2 Note that, for a trapezoid,

10

Cantilever Footing
Cantilever footing construction uses a strap beam to connect an eccentrically
loaded column foundation to the foundation of an interior column. (See
Figure 6.3). Cantilever footings may be used in place of trapezoidal or
rectangular combined footings when the allowable soil bearing capacity is
high and the distances between the columns are large.

11

Cantilever Footing
Their purpose is to redistribute Excesses stresses, and possible
differential settlements between adjacent spread footings.

12

Example 1
Find the Dimensions of the combined footing for the columns A and B
that spaced 6.0 m center to center, column A is 40 cm x 40 cm carrying
dead loads of 50 tons and 30 tons live load and column B is 40 cm x 40
cm carrying 70 tons dead load and 50 tons live loads.

13

Example 1
1- Find the required area:

2- Find the resultant force location (Xr):

3- To ensure uniform soil pressure, the resultant force (R) should be in

the center of rectangular footing:

14

Example 2
Find the Dimensions of the trapezoidal combined footing for the
columns A and B that spaced 4.0 m center to center, column A is 40 cm
x 40 cm carrying dead loads of 80 tons and 40 tons live load and
column B is 30 cm x 30 cm carrying 50 tons dead load and 25 tons live
loads.

15

Example 2
1- Find the required area:

2- Determine the resultant force

16

Example 2
3- Put the resultant force location at the centroid of trapezoid to
achieve uniform soil pressure.

For uniform soil pressure:

17

Example 3
Design a strap footing to support two columns, that spaced 4.0 m
center to center exterior column is 80cm x 80cm carrying 1500 KN
and interior column is 80cm x 80cm carrying 2500 KN

18

Example 3
1- Find the resultant force location:

2- Assume the length of any foot, let we assume L1=2m.

19

Example 3
3- Find the distance a:

20

Example 3
4- Find the resultant of each soil pressure:

5- Find the required area for each foot:

21

Common Types of Mat Foundations

The mat foundation, which is sometimes referred to as a raft foundation,

is a combined footing that may cover the entire area under a structure
supporting several columns and walls.

Mat foundations are sometimes preferred for soils that have low loadbearing capacities, but that will have to support high column or wall
loads.

Under some conditions, spread footings would have to cover more than
half the building area, and mat foundations might be more economical.

Several types of mat foundations are used currently.

Some of the common ones are shown schematically in Figure 6.4 and
include the following:

22

Common Types of Mat Foundations

1. Flat plate (Figure 6.4a). The mat is of uniform thickness.

2. Flat plate thickened under columns (Figure 6.4b).
3. Beams and slab (Figure 6.4c). The beams run both ways, and the columns
are located at the intersection of the beams.
23

Common Types of Mat Foundations

4. Flat plates with pedestals (Figure 6.4d).

5. Slab with basement walls as a part of the mat (Figure 6.4e). The walls act
24
as stiffeners for the mat.

Common Types of Mat Foundations

25

Bearing Capacity of Mat Foundations

The gross ultimate bearing capacity of a mat foundation can be determined
by the same equation used for shallow foundations

The net ultimate capacity of a mat foundation is

A suitable factor of safety should be used to calculate the net allowable

bearing capacity.

For mats on clay, the factor of safety should not be less than 3 under
dead load or maximum live load.

However, under the most extreme conditions, the factor of safety
should be at least 1.75 to 2.

For mats constructed over sand, a factor of safety of 3 should
normally be used. Under most working conditions, the factor of safety
26
against bearing capacity failure of mats on sand is very large.

Bearing Capacity of Mat Foundations

For saturated clays with = 0 and a vertical loading condition, Eq.
(3.19) gives

From Table 3.4, for = 0

Substitution of the preceding shape and depth factors into Eq. (6.8) yields

27

Bearing Capacity of Mat Foundations

Hence, the net ultimate bearing capacity is

For FS = 3, the net allowable soil bearing capacity becomes

The net allowable bearing capacity for mats constructed over granular soil
deposits can be adequately determined from the standard penetration
resistance numbers. From Eq. (5.64), for shallow foundations,

28

Bearing Capacity of Mat Foundations

When the width B is large, the preceding equation can be approximated as

In English units, Eq. (6.12) may be expressed as

29

Bearing Capacity of Mat Foundations

The net allowable pressure applied on a foundation (see Figure 6.7) may be
expressed as

30

Examples 6.1 & 6.2

31

Compensated Foundation
Figure 6.7 and Eq. (6.15) indicate that the net pressure increase in the soil
under a mat foundation can be reduced by increasing the depth Df of the
mat. This approach is generally referred to as the compensated foundation
design and is extremely useful when structures are to be built on very soft
clays. In this design, a deeper basement is made below the higher portion of
the superstructure, so that the net pressure increase in soil at any depth is
relatively uniform. (See Figure 6.8.)

32

Compensated Foundation
From Eq. (6.15) and Figure 6.7, the net average applied pressure on soil is

For no increase in the net pressure on soil below a mat foundation, q should
be zero. Thus,

The factor of safety against bearing capacity failure for partially compensated
foundations
may be given as

33

Compensated Foundation
For saturated clays, the factor of safety against bearing capacity failure can
thus be obtained by substituting Eq. (6.10) into Eq. (6.20):

34

Example 6.3

35

Example 6.4

36

Example 6.4

37

Example 6.4

38

Structural Design of Mat Foundations

The structural design of mat foundations can be carried out by two
conventional methods:

conventional rigid method

approximate flexible method.
Finite-difference and finite-element methods can also be used, but this
section covers only the basic concepts of the first two design methods.

39

Conventional Rigid Method

The conventional rigid method of mat foundation design can be explained
step by step with reference to Figure 6.10:

40

Conventional Rigid Method

41

Conventional Rigid Method

Step 1. Figure 6.10a shows mat dimensions of L x B and column loads of Q1,
Q2, Q3 . Calculate the total column load as

Step 2. Determine the pressure on the soil, q, below the mat at points A, B, C,
D, , by using the equation

42

Conventional Rigid Method

43

Conventional Rigid Method

Step 3. Compare the values of the soil pressures determined in Step 2 with
the net allowable soil pressure to determine whether
Step 4. Divide the mat into several strips in the x and y directions. (See Figure
6.10). Let the width of any strip be B1 .
Step 5. Draw the shear, V, and the moment, M, diagrams for each individual
strip (in the x and y directions). For example, the average soil pressure
of the bottom strip in the x direction of Figure 6.10a is

44

Conventional Rigid Method

The total soil reaction is equal to
Now obtain the total column load
on the strip as
The sum of the column loads on the strip
will not equal
because the shear between the adjacent strips has
not been taken into account. For this reason, the soil reaction and the
column loads need to be adjusted, or

Now, the modified average soil reaction becomes

and the column load modification factor is

45

Conventional Rigid Method

So the modified column loads are
This modified
loading on the strip under consideration is shown in Figure 6.10b. The shear
and the moment diagram for this strip can now be drawn, and the procedure
is repeated in the x and y directions for all strips.
Step 6. Determine the effective depth d of the mat by checking for diagonal
tension shear near various columns. According to ACI Code 318-95
(Section 11.12.2.1c, American Concrete Institute, 1995), for the
critical section,

46

Conventional Rigid Method

Step 7. From the moment diagrams of all strips in one direction (x or y),
obtain the maximum positive and negative moments per unit width

Step 8. Determine the areas of steel per unit width for positive and negative
reinforcement in the x and y directions. We have

47

Example 6.5

48

Example 6.5

49

Example 6.5

50

Example 6.5

51

Example 6.5

52

Example 6.6

53

Example 6.6

331.70

1727.57

54

Example 6.6

55

Example 6.6

56

Example 6.6

57

Example 6.6

58

Example 6.6

59

Example 6.6

60

Example 6.6

61

Example 6.6

62

Example 6.6

63

Example 6.6

64

Approximate Flexible Method

In the conventional rigid method of design, the mat is assumed to be
infinitely rigid. Also, the soil pressure is distributed in a straight line,
and the centroid of the soil pressure is coincident with the line of
action of the resultant column loads. (See Figure 6.11a.) In the
approximate flexible method of design, the soil is assumed to be
equivalent to an infinite number of elastic springs, as shown in Figure
6.11b. This assumption is sometimes referred to as the Winkler
foundation. The elastic constant of these assumed springs is referred
to as the coefficient of subgrade reaction, k.

65

Approximate Flexible Method

To understand the fundamental concepts behind flexible foundation design,
consider a beam of width B1 having infinite length, as shown in Figure 6.11c.
The beam is subjected to a single concentrated load Q. From the
fundamentals of mechanics of materials,

66

Approximate Flexible Method

67

Approximate Flexible Method

Combining Eqs. (6.35) and (6.36) yields

However, the soil reaction is

So,

68

Approximate Flexible Method

Solving Eq. (6.38) yields

The unit of the term as defined by the preceding equation, is (length-1). This
parameter is very important in determining whether a mat foundation
should be designed by the conventional rigid method or the approximate
flexible method. According to the American Concrete Institute Committee
336 (1988), mats should be designed by the conventional rigid method if the
spacing of columns in a strip is less than 1.75/. If the spacing of columns is
larger than 1.75/ the approximate flexible method may be used.
69

Approximate Flexible Method

To perform the analysis for the structural design of a flexible mat, one must
know the principles involved in evaluating the coefficient of subgrade
reaction, k. Before proceeding with the discussion of the approximate
flexible design method, let us discuss this coefficient in more detail.
If a foundation of width B (see Figure 6.12) is subjected to a load per unit
area of q, it will undergo a settlement . The coefficient of subgrade modulus
can be defined as

The unit of k is kN/m3.

70

Approximate Flexible Method

The value of k can be related to large foundations measuring in the following
ways:

Foundations on Sandy Soils

Foundations on Clays

Approximate Flexible Method

For rectangular foundations having dimensions of BxL (for similar soil and q),

Approximate Flexible Method

Approximate Flexible Method

For long beams,Vesic (1961) proposed an equation for estimating subgrade
reaction, namely,

For most practical purposes, Eq. (6.46) can be approximated as

Approximate Flexible Method

The approximate flexible method of designing mat foundations, as proposed
by the American Concrete Institute Committee 336 (1988), is described step
by step.
Step 1. Assume a thickness h for the mat, according to Step 6 of the
conventional rigid method. (Note: h is the total thickness of the mat.)
Step 2. Determine the flexural ridigity R of the mat as given by the formula

Step 3. Determine the radius of effective stiffnessthat is,

Approximate Flexible Method

Step 4. Determine the moment (in polar coordinates at a point) caused
by a column load (see Figure 6.13a). The formulas to use are

Approximate Flexible Method

Step 5. For the unit width of the mat, determine the shear force V caused by
a column load:

Step 6. If the edge of the mat is located in the zone of influence of a column,
determine the moment and shear along the edge. (Assume that the
mat is continuous.) Moment and shear opposite in sign to those
determined are applied at the edges to satisfy the known conditions.

Approximate Flexible Method

Step 7. The deflection at any point is given by

End of Chapter 6

79

HW # 4
Due to Sunday, 3/11/2013

Solve problems:
6.2, 6.4, 6.6, 6.8 and 6.10