Scribd
Upload
201 views

Example Balloon Write Up

Increasing the number of lit candles used to heat a hot air balloon affects the time it takes the balloon to rise to a given height. Specifically, a balloon powered by three candles on average took 10.4 seconds to rise 20 feet, while a balloon with two candles took 13.0 seconds and one candle took 14.8 seconds. The hypothesis that more candles would decrease rise time was correct, though the actual times were slower than predicted. Other considerations included the potential effect of wax weight changes as candles burn.

Uploaded by

Anonymous L77eD5uo
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
201 views

Example Balloon Write Up

Increasing the number of lit candles used to heat a hot air balloon affects the time it takes the balloon to rise to a given height. Specifically, a balloon powered by three candles on average took 10.4 seconds to rise 20 feet, while a balloon with two candles took 13.0 seconds and one candle took 14.8 seconds. The hypothesis that more candles would decrease rise time was correct, though the actual times were slower than predicted. Other considerations included the potential effect of wax weight changes as candles burn.

Uploaded by

Anonymous L77eD5uo
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 8

Candle-Powered Hot Air BalloonThis is a sample of a science project.

Problem

[5 - 8

sent]
All scientific approaches
begin with the question
What do I want to find
out? This is your
problem, or what it is
youre trying to answer.
Briefly introduce your
topic and connect it to
your problem. Keep the
problem statement
specified and focused. Be
sure to include your
question here. Rewrite
this paragraph until it
says exactly what you
want it to say.

Hot air balloons have been around since at


least 1783 with the first manned flight by the
Montgolfier brothers in a twenty-minute trip.
Balloons have now become a common sight in many
areas including in the wine-country of Temecula
Valley. Hot air balloons essentially work on the
simple principle that hot air rises with relatively cold
air around it. A balloon filled with warm air will rise
based on how warm or hot the air inside the balloon
is compared to the surrounding air.
In this experiment, a small balloon filled with
warm air provided by candles in the basket will rise
into the air. On different flights, a different number of
candles will help provide the lift needed. What effect
does increasing the number of lit candles used have
on the time it takes a hot air balloon to rise to a
given distance?

Hypothesis

[ 6-8

sent. ]
After researching, you
should be able to make
an educated guess to
answer your question.
The hypothesis should
include:
1) the focus of the
experiment;
2) whats being
measured;
3) expected results; and
4) why you expect those
results.

[Focus:] A balloon is constructed using lightweight


balsa wood as a basket, kite string for the rope lines, and a
garbage bag as the balloon material. Candles heat the air
from the basket. [Whats being measured:] The balloon is
to be timed to a height of twenty feet with one, two, and
three candles being lit.
[Expected results and why those results are
expected:] Since the research suggests that the greater
heat will create greater lift, it is hypothesized that the
three-candled flight will create the greatest lift and
therefore will take less time to reach a height of twenty
feet. Specifically, the three candle balloon will rise to
twenty feet in eight seconds, the two-candle balloon in ten

seconds, and the onecandle balloon in 14


seconds.

Experiment
This is where you actually do the experiment as described in
procedure steps number 12 to 14.

Materials
This is a detailed list of all
materials needed for the

4 x 24 x balsa wood

project. This needs to

40 feet of kite string

include all tools as well as

13-gallon trash bag

the quantity of an item

three tea candles

when required.

matches
stopwatch to tenths-of-a-second accuracy
knife to cut balsa wood (X-Acto or utility knife)
measuring tape or ruler

Procedure
This is a step-by-step list
of every part of the

1.

experiment including

2.

building/setting up, how

3.

to measure data, what

4.

data to collect, and the

5.

steps to change the

variable. This should be

so detailed that another

student should be able to

12. Run experiment three times with a single candle lit, timing

look at the procedure and

how long it

duplicate it him/herself.

the basket) Record data.

Think of this as a recipe

13. With new candles, run the experiment with two candles lit.

that also tells how to

Record

measure the results.

14. With new candles, run the experiment with three candles lit.
Record

takes to reach 20 feet (the length of the tether on

data.
data.

Table and Graph


Record your data in a
table and a graph.
Choose a graph based
on the type of data you
have collected. (For
example, a line graph
is used for changes
over time.)

Analysis /
Summary of
Results
How exactly is your
experiment
measured?

Any changes to or problems with your experiment.

Flight

to reach a height of 20 feet is timed. There is a string 20

Times for Hot Air

feet long attached to the bottom of the basket that is held

Balloons (in seconds)

to the ground to determine when the twenty-foot high


mark has been reached. Each flight is repeated three times

Flight

Flight and an average is found for each number of candles. The

1 Candle

#1
14.2

time is determined to the nearest tenth of a second.


#2
15.1

2 Candle

12.6

13.2

3 Candle

11.2

10.2

One item that had to be changed was the addition of


weight to the one- and two-candle powered balloons. When
initially run, the procedure didnt take
into account the varying weight
determined by the number of candles.
The one candle balloon had the weight of
only one candle and was therefore
lighter than the three-candle balloon. It
was decided to add unlit candles so each
balloon had the weight of three candles.
Analysis /Summary of Results (cont.)
Actual results.

A hot air balloon is


constructed of balsa
wood and tissue paper.
It has the air heated
inside it by candles.
The same balloon is
used for all flights but
the number of candles

Conclusion:

increases from the first

#1 Answer the question. Describe the data

flight having only one


candle, the next having
two candles, and the
third having three
candles. The time it
takes for the balloons

#2 Evaluate the hypothesis.

Restate the hypothesis;


was the hypothesis

The balloons with one-candle power had flight times

correct, incorrect, or

of 14.2 seconds, 15.1 seconds, 14.8 seconds, and 15.1

partially correct.

seconds for an average of 14.8 seconds. The balloons with


two-candle power had flight times of 12.6, 13.2, 13.0, and
13.2 seconds, for an average of 13.0 seconds. The threecandled balloons had times of 11.2, 10.4, 10.2, and 9. 8
seconds for an average time of 10.4 seconds. Therefore the
number of candles determined the speed at which the

#3 Other

balloon rose: three candles were quickest, two candles

considerations.

second, and the single candle balloon the slowest.

Increasing the number of candles causes a hot air balloon


to rise at a more rapid rate. In fact, the three candles
balloon flight average of 10.4 seconds was 2.6 seconds
faster than the two-candle average, and 4.4 seconds faster
than the one-candle balloon.
In the hypothesis, it was thought that the more
candles would decrease the time to reach twenty feet;
therefore, the hypothesis was correct about the order of
completing the 20-foot distance. The extra heat provided
by the greater quantity of candles heated the air enough to
make a difference between the air temperature inside the
balloon and the air temperature outside the balloon to
make it rise quicker. One part incorrect in the hypothesis
was the belief that the balloons would rise faster than they
actually did. This was incorrect due to completing guessing
as to the time since there was no background knowledge,
even with the research, as to how long a model balloon
would take to rise.
One other consideration would be the possible
weight change of a balloon as the candle melts the wax.

Though the weight


change would likely be
very small, its not
known if that would
have an effect on the
weight and therefore
the time.

#4 Other thoughts or
new questions.

Trying to decide how to generate the heat needed to


fill the balloon to create lift was a challenge. Most sources,
such as propane, are far too heavy to create enough lift to
overcome the weight, for example, of a propane tank. One
other observation was not being sure whether the burned
wax, as a liquid, would weigh more or less than the wax
before its melted. In addition, candles appear to lose some
mass while they burn, thus they get shorter even assuming
some melting down the sides. Though the difference is
possibly trivial, its still a consideration.

#5 What did you


learn about doing

experiments in this

project?

:
:
:
:

You might also like