Scribd
Upload
3K views

2.2.5.5 Packet Tracer - Configuring Floating Static Routes Instructions

This document provides instructions for configuring IPv4 and IPv6 floating static routes in Packet Tracer. It has the student configure a default static route and backup floating static route for IPv4, then test failover when the primary route fails. It then has the student repeat this for an IPv6 floating static route.

Uploaded by

ShriRam Hegde
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
3K views

2.2.5.5 Packet Tracer - Configuring Floating Static Routes Instructions

This document provides instructions for configuring IPv4 and IPv6 floating static routes in Packet Tracer. It has the student configure a default static route and backup floating static route for IPv4, then test failover when the primary route fails. It then has the student repeat this for an IPv6 floating static route.

Uploaded by

ShriRam Hegde
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Packet Tracer - Configuring Floating Static Routes

Topology

Objectives
Part 1: Configure an IPv4 Floating Static Route
Part 2: Test Failover to the IPv4 Floating Static Route
Part 3: Configure and Test Failover for an IPv6 Floating Static Route

Background
In this activity, you will configure IPv4 and IPv6 floating static routes. These routes are manually configured
with an administrative distance greater than that of the primary route and, therefore, would not be in the
routing table until the primary route fails. You will test failover to the backup routes, and then restore
connectivity to the primary route.

Part 1: Configure an IPv4 Floating Static Route


Step 1: Configure an IPv4 static default route.
a. Configure a directly connected static default route from Edge_Router to the Internet. The primary default
route should be through ISP1.
b. Display the contents of the routing table. Verify that the default route is visible in the routing table.
c.

What command is used to trace a path from a PC to a destination? tracert


From PC-A, trace the route to the Web Server. The route should start at the default gateway
192.168.10.1 and go through the 10.10.10.1 address. If not, check your static default route configuration.

Step 2: Configure an IPv4 floating static route.


a. What is the administrative distance of a static route? 1
b. Configure a directly connected floating static default route with an administrative distance of 5. The route
should point to ISP2.
c.

View the running configuration and verify that the IPv4 floating static default route is there, as well as the
IPv4 static default route.

2016 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public.

Page 1 of 3

Packet Tracer - Configuring Floating Static Routes


d. Display the contents of the routing table. Is the IPv4 floating static route visible in the routing table?
Explain

255.255.255.255

Part 2: Test Failover to the IPv4 Floating Static Route


a. On Edge_Router, administratively disable the exit interface of the primary route.
b. Verify that the IPv4 floating static route is now in the routing table.
c.

Trace the route from PC-A to the Web Server.


Did the backup route work? If not, wait a few more seconds for convergence and then re-test. If the
backup route is still not working, investigate your floating static route configuration.

d. Restore connectivity to the primary route.


e. Trace the route from PC-A to the Web Server to verify that the primary route is restored.

Part 3: Configure and Test Failover to an IPv6 Floating Static Route


Step 1: Configure an IPv6 floating static route.
a. The IPv6 static default route to ISP1 is already configured. Configure an IPv6 floating static default route
with an administrative distance of 5. The route should point to IPv6 address (2001:DB8:A:2::1) of ISP2.
b. View the running configuration to verify that the IPv6 floating static default route is now listed under the
IPv6 static default route.

Step 2: Test Failover to the IPv6 Floating Static Route.


a. On Edge_Router, administratively disable the exit interface of the primary route.
b. Verify that the IPv6 floating static route is now in the routing table.
c.

Trace the route from PC-A to the Web Server.


Did the backup route work? If not, wait a few more seconds for convergence and then re-test. If the
backup route is still not working, investigate your floating static route configuration.

d. Restore connectivity to the primary route.


e. Trace the route from PC-A to the Web Server to verify that the primary route is restored.

2016 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public.

Page 2 of 3

Packet Tracer - Configuring Floating Static Routes

Suggested Scoring Rubric


Activity Section
Part 1: Configuring a
Floating Static Route

Question
Location

Possible
Points

Step 1c

Step 2a

Step 2d

Part 1 Total

10

Packet Tracer Score

90

Total Score

100

2016 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public.

Earned
Points

Page 3 of 3

You might also like