Using the Akta Prime plus

October 22, 2012

Some starting precautions:
1. Vacuum filter all buffers.
Removes any large particles/debris that may clog your column
De-gases the buffers
2. Clarify lysates first by centrifugation and then filtration using a 0.22m membrane
removes any large particles/debris that may clog your column
3. Be aware of the limits of your respective column!
o Parameters to be aware of
Pressure limits
Flow rates
Chemical compatibility
Column volume
4. All connections must be finger tight only! Over tightening connections will break the connectors
or portions of the instrument.
5. The system is stored in 20% ethanol. Make certain that you flush the system with water before
working with buffers or proteins.
Getting Started:
1. Turn on the Akta primeplus. The switch is located at the back of the instrument on the left hand
side.
2. Turn on the computer and log into Windows
3. Launch the Primeview software
a. Beware! Dont launch the Primeview evaluation software.
b. You cannot control the instrument from the software. All user commands are inputted
through the interface on the front of the instrument itself.

1|Jenni fer Arr uda

Using the Akta Prime plus

October 22, 2012
Flushing the Lines:
1. Place a black cap onto the top of a bottle of filtered MilliQ water or water and insert lines A1
and B through the cap and into the water or buffer as appropriate.
Flush the lines any time that you transfer the lines from one bottle to another. This will
prevent any air from reaching your column and damaging it.
2. Make certain that there is a small bubble in the very end of each line. You can trace the path of
the bubbles through the lines to confirm that the lines were primed correctly
3. Make certain that the ends of each line touch the bottom of the bottle and do not curve up the
sides of the bottles.
4. Use the up and down arrows to scroll through the menu until you reach templates
5. Scroll to application template
6. Scroll to system wash method
7. At this point, you can select the line(s) you will be using and flush all of the lines at once. The
default is lines A1 and B so we wont change anything. Use the up/down arrows to scroll over to
OK then press the OK button.
8. The message PRESS OK TO START RUN will be displayed on the LCD screen on the instrument.
Press OK and the system will start.
The system may prompt you to check tube position. If it does so, press OK to start the
run and pause/cont. to begin.
9. The system will run at 50 mL/min for a total of 75 mL for two lines. As the method progresses
make certain that the bubbles are pushed all the way through the lines. You may have to flick
the lines to dislodge any bubble that may be clinging to the interior of the lines.
10. Once the volume has reached 75 mL, the flow rate will drop to 0.5 mL/min. you can end the
system wash at this point.
11. Press end. The system will display the message END RUN? YES NO. Make certain that the
underscore is below the word YES and press OK
12. The system will then display the message MEMORY PRINT OUT? YES NO. Make certain that
the underscore is below the word No and press OK. NEVER select yes for the memory print out.

2|Jenni fer Arr uda

Using the Akta Prime plus

October 22, 2012
Attaching the column and washing the ethanol from the column:
1. Flush the lines with water (See step 4).
2. Once the lines have been washed with water, you will need to start a manual run before
attaching your column to the system.
When attaching or removing a column ALWAYS have water or buffer moving through
the system.
3. At this point the screen should display TEMPLATES, use the up/down arrows to scroll through
the menu until you reach the option that says MANUAL RUN. Press OK.
4. You are now at a point where you can begin to enter the run parameters.
Method base: mL
Flow rate: 1.0 mL/minute
Pressure limit: column pressure limit
5. Scroll down to START RUN and then press OK.
Monitor the system back pressure
without the column first for several
minutes before attaching the column. It
may be necessary to set the pressure limit
higher than the column limit due to
system back pressure.
6. Unscrew the connectors from the UV detector.
Either of the top two connectors will be
appropriate to attach the tubing from the
injection valve to your column. Open the top of
your column and allow water to drip into the
opening then attach the connector to the top of
the column. Do not tighten completely.
7. Once the top has been loosely attached to the
connector, remove the bottom cap and attach
the column to the bottom connector and
tighten firmly. Do not attach the column directly
to the detector. The plastic encasing the resin is
soft and can break off inside the detector.
8. Tighten the top connector and wipe away excess water. The idea is to have every connection to
be finger tight but not leaking.
9. Allow approximately 1 column volume (CV) to flow the column at a flow rate of 1 mL per minute
then using the control panel on the front of the instrument scroll until you see the prompt for
flow rate and increase the flow rate. Allow water to flow through the column for 5 10 column
volumes.
10. Once you have washed the column with water end the manual run.

3|Jenni fer Arr uda

Using the Akta Prime plus

October 22, 2012
Equilibrating the column into Buffer:
1. Transfer Line A1 into Buffer A and Line B into Buffer B
2. Flush the lines with buffer
Make certain that there is a small bubble in the very end of each line. You can trace the path
of the bubbles through the lines to confirm that the lines were primed correctly
Make certain that the ends of each line touch the bottom of the bottle and do not curve up
the sides of the bottles.
3. At this point the screen should display TEMPLATES, use the up/down arrows to scroll through
the menu until you reach the option that says manual run. Press OK.
4. You are now at a point where you can begin to enter the run parameters.
a. Method base: mL
b. Flow rate: 1.0 mL/minute
c. Pressure limit: column pressure limit
5. Scroll down to start run and then press OK.
6. Allow approximately 1 column volume to flow the column at a flow rate of 1 mL per minute then
using the control panel on the front of the instrument scroll until you see the prompt for flow
rate and increase the flow rate. Allow buffer to flow through the column for 5 10 column
volumes. Once you have a stable baseline and while the column is still equilibrating, use the
up/down arrows to scroll to AUTOZERO UV and press OK.

Preparing your sample loop/super loop:

This can be done while the column is being equilibrated.
Sample Loop:
1. Flush the sample loop first with water then with
Buffer A.
2. Attach one end of the loop to port #6 and the
other to port #2. You can identify the ports by the
numbers etched on the metal ring of the injection
valve. Alternatively, port #6 has been marked on
the front of the injection valve with a T as shown
in the image below and port #2 is directly
opposite port #6.
3. Once the sample loop has been attached it is a
good idea to inject buffer through the loop to
confirm that there are no leaks.
4. Scroll down and decrease your flow rate to 1
mL/minute.
4|Jenni fer Arr uda

Using the Akta Prime plus

October 22, 2012
5. Scroll down until you see the message SET INJECT VALVE POSITION (LOAD). Press OK.
6. Use the up/down arrows to move the underscore from beneath the word LOAD to beneath INJ.
Then press OK.
7. This changes the system from loading to injection which puts the sample loop in line with the
column. The system will begin to push buffer through the sample loop. Check carefully to be
certain that there are no apparent leaks. If any connector is leaking adjust/tighten the
connectors until the leaking stops.
8. Once you have allowed several milliliters to be injected onto the column. Use the up/down
arrows until you see the message SET INJECT VALVE POSITION (INJ). Press OK.
9. Use the up/down arrows to move the underscore from beneath Inj to beneath LOAD. Then press
OK.
10. This changes the system from injection to load and bypasses the sample loop.
Super Loop:
1. The super loop is used to inject larger volumes onto the column.
2. Carefully remove one of the black caps of the super loop and set aside. Slide off the plastic outer
casing. Hold tightly to the glass super loop and remove the white plastic plug from the end of
the loop. Allow the water to drain from the end of the super loop.
To improve your grip on the glass portion of the super loop, hold the loop with a dry
paper towel.
3. Remove the remaining black cap
and white plug from the
opposing end of the super loop.
Again allowing the water to
drain from the super loop.
4. Rinse each side of the super loop
and the white caps with water 3
times.
5. Rinse each side of the super loop
with Buffer A 3 times.
6. Fill each end of the super loop
with Buffer A and replace the
white plastic plugs.
7. Attach a black plastic cap to one
end of the super loop and insert
the glass super loop into the
plastic outer casing.
8. Attach the remaining black plastic cap to the super loop and make sure that both caps are firmly
tightened.
9. Insert the super loop into one of the clips attached to the side of the Akta.

5|Jenni fer Arr uda

Using the Akta Prime plus

October 22, 2012
10. Obtain two lines with adaptors suitable to attach to the super loop and using a syringe without a
needle flush the lines first with water then with buffer A.
11. Attach one line to the top of the super loop and from there to port #6.
12. Attach the second line to the bottom of the super loop and from there to port #2.
a. You can identify the ports by the numbers etched on the metal ring of the injection
valve. Alternatively, port #6 has been marked on the front of the injection valve with a T
as shown in the image above and port #2 is directly opposite port #6.
13. Once the sample loop has been attached it is a good idea to inject the buffer contained in the
lower portion of the super loop onto the column to confirm that there are no leaks and to speed
things along.
14. Scroll down and decrease your flow rate to 1 mL/minute.
15. Scroll down until you see the message SET INJECT VALVE POSITION (LOAD). Press OK.
16. Use the up/down arrows to move the underscore from beneath the word LOAD to beneath INJ.
Then press OK.
17. This changes the system from loading to injection which puts the super loop in line with the
column. The system will begin to push buffer into the upper portion of the super loop causing
the plunger to descend. Check carefully to be certain that there are no apparent leaks. If any
connector is leaking adjust/tighten the connectors until the leaking stops.
18. Allow all of the buffer contained in the lower portion of the super loop to be injected onto the
column. Halt the injection when the small bubbles contained in the super loop just begin to
compress.
19. Use the up/down arrows until you see the message SET INJECT VALVE POSITION (INJ). Press OK.
20. Use the up/down arrows to move the underscore from beneath INJj to beneath LOAD. Then
press OK.
21. This changes the system from injection to load and bypasses the sample loop.
22. Once the column has finished equilibrating end the manual run.

Loading your sample into the Sample/Super Loop and Injecting onto the Column:
1. Start a manual run and set the following parameters
Method base: min
Flow rate: 1.0 mL/minute
Pressure limit: column pressure limit
2. Load your sample into the sample/super loop by first loading it into a luer lock syringe and then
attaching the syringe to the connector on the face of the injection valve. Slowly depress the
plunger to push the sample from the syringe into the loop.
Make sure that there are NO bubbles in the syringe before you attach the syringe to the
connector.
The largest syringe volume you can use is 25 mL. If you are loading a larger volume into
a super loop, you can iteratively fill the syringe and load into the super loop.
6|Jenni fer Arr uda

Using the Akta Prime plus

October 22, 2012
3. Change the injection valve position from load to inject. Stop the injection before any bubbles
reach the injection valve.
4. Wash the column at 1 mL/minute until UV trace drops to approximately 1200 mAU. Increase the
flow rate and continue to wash the column until the UV trace reaches baseline.
5. You can then elute your protein in a number of different ways.
a. Gradient elution
b. Step elution
c. Isocratic elution
Setting a gradient elution
1. Using the control panel scroll down to set gradient. Press OK and set the following parameters
a. Gradient length: 60 minutes
b. Set Target: 100% buffer B
Once the parameters are set, press OK. The system will begin a gradient elution. This is a good
starting point but the parameters can be altered to improve the resolution of the elution.
2. Scroll down to set fraction size. Press OK. Set fraction size to 1.0 mL. The fraction collector will
begin to collect 1 mL fractions.
Setting a Step elution
1. Using the control panel scroll down to Set Concentration %B (0%B). Press OK. Use the up/down
arrows to set the desired percentage of buffer B and then press OK.
a. Each individual step will need to be adjusted in this manner.
2. Scroll down to set fraction size. Press OK. Set fraction size to 1.0 mL. The fraction collector will
begin to collect 1 mL fractions.

7|Jenni fer Arr uda

Using the Akta Prime plus

October 22, 2012

8|Jenni fer Arr uda

Using the Akta Prime plus

October 22, 2012
Saving Your Chromatogram
The Akta system by default saves your chromatogram data as Manual run 1, 2, 3 and so on. It is
recommended that you set up a file to save the data from individual purifications. If you have already
created a folder for your chromatogram data you can ignore the next several steps

Open Primeview Evaluation

Click file (in the upper left hand corner)
The open result window will open
Right click inside the open result window and a small menu will pop up
Click on New Folder
Name your folder.

To save the file make note of the manual run number. It will be displayed at the top of the screen in
Primeview.

Open Primeview Evaluation

Click file (in the upper left hand corner)
The open result window will open
Scroll down until you see a folder named Manual Runs (prime)
Double click to open the folder and locate the manual run that you want to save
Double click on the file name to open the file and you will see your chromatogram dislayed on
the screen
Go to file
Click on save as and the save as window will open
Navigate through the files until you reach your folder and double click on the folder
Re-name your chromatogram and save your chromatogram to your folder.

9|Jenni fer Arr uda