Front panel identification

TIMER

LE4S
M

Output operation mode

Time progressing display:It displays the current time.

Time setting display:It displays the setting time.
Time unit:It displays the time unit.
Operation mode:It displays the current operation mode.
Output display:It displays the status of output contact.
UP/DOWN:It displays time progressing UP(), DOWN().
Key lock display:It displays the status of key lock.
,key:Used for initializing time progressing and output return.
*key:Used for advancing to function setting mode, setting
time change checking.
<key:Used for advancing to setting time change mode and
moving to each digit.
>key:Used for changing the set value.

Function Setting Mode Descriptions

Thank you very much for selecting Autonics products.
For your safety, please read the following before using.
Output operation mode
* key

* key

Please observe the cautions that follow;

RUN mode

Warning Serious injury may result if instructions are not followed.

Caution Product may be damaged, or injury may result if instructions are not followed.
The following is an explanation of the symbols used in the operation manual.
caution:Injury or danger may occur under special conditions.

Warning

OND I

* key

T.OFFTime Range

* key
* key

T.ONTime Range

* key

* key

3)Time Up/Down

* key

* key

S
Output

Time limit contact 1c

Time limit contact 2c,
A
Instantaneous contact 1c + Time limit contact 1c(Selectable)

Size

Item
Display

ON Delay 2
(One-Shot
Output)

1) Time Range
Parameter

Time range specification

9.999S (9.999s)

0.010 sec

9.999 sec

99.99S (99.99s)
999.9S (999.9s)

0.01 sec

99.99 sec

0.1 sec

999.9 sec

1 sec

9999 sec

0 min 01 sec

99 min 59 sec

999.9m (999.9m)
9999m (9999m)

0.1 min

999.9 min

1 min

9999 min

99h 59m (99h59m)

99.99h (99.99h)

0 hour 01 min

99 hour 59 min

0.01 hour

99.99 hour

Flicker

0.1 hour

999.9 hour

1 hour

9999 hour

(Toff operation
precedes
Ton operation)

9999S (9999s)
99m 59S (99m59s)

999.9h (999.9h)
9999h (9999h)

FK

It will be activated when selecting ON Delay 2[ OND.2] output operation mode

(One-Shot-output mode).(Time setting: 0.01 sec ~ 99.99 sec)

3) Time progress UP/DOWN setting

<key

L LCD Display

<key

Set the minimum input signal of RESET, START and INHIBIT

Min. input signal: Choose 1ms and 20ms

5) Backlight setting
(Unit:mm)

56

FK I

Set Backlight (ON[ ON], OFF[ OFF]).

>key

[ INT]

<key

14

(Ton operation
precedes
Toff operation)

INT

48

44.8

6) Key Lock selection

Panel cut-out

<key

Product mounting

Interval

>key

>key

>key

<key

<key

<key

45+0.6
-0
45

,key cannot
be used.

Turns off the

Lock mode.

<,>key cannot
be used.

,,<,>key
cannot be used.

Time setting
Insert product into a panel, fasten braket by pushing
with tools as shown above.

INT I

Output operation mode : OND, OND I, OND II, INT, INT I, OFF D

LE4S

Power supply
Display method
Allowable voltage range
Power consumption
Return time
Min.input signal
(START,INHIBIT,RESET)

24-240VAC 50/60Hz, 24-240VDC

LCD Display(Backlight)
90 ~ 110% of rated voltage
24-240VAC: Max. 4.5VA, 24-240VDC: Max. 2W
Max. 100ms

Input
(START,INHIBIT,RESET)

<No-voltage input>
Impedance at short-circuit: Max. 1, Residual voltage: Max. 0.5V,
Impedance at open-circuit: Min. 100

Con- Type
tact Capacity
RepeatSettingVoltage
Temperature error
Ambient temperature
Storage temperature
Ambient humidity
Insulation resistance
Dielectric strength
Mechanical
Vibration
Malfunction
Shock
Relay
life cycle

[Fig. 1]

Mechanical
Malfunction
Mechanical
Electrical

Time limit SPDT(1c)

250VAC 5A resistive load
Max. 0.005% 0.03sec (Signal Start)
Max. 0.01% 0.05sec (Power ON Start)
-10 ~ 55(at non-freezing status)
-25 ~ 65(at non-freezing status)
35 ~ 85%RH
Min. 100M(500VDC megger)
2,000VAC 50/60 for 1 minute
0.75mm amplitude at frequency of 10 ~ 55
in each of X, Y, Z directions for 1hour
0.5mm amplitude at frequency of 10 ~ 55
in each of X, Y, Z directions for 10 minutes
300m/s(30G) X, Y, Z directions for 3 times
100m/s(10G) X, Y, Z directions for 3 times
Min. 10,000,000 times
Min. 100,000 times(250VAC 5A resistive load)

[Fig. 2]

[Fig. 3]

[Fig. 4]

[Fig. 5]

Press <key in RUN mode, time set digits will flash.[Fig. 1]

Change setting time by press < or >keys.[Fig. 2,3,4]
-<key:Shift the setting digits.
->key:Shift the flashing position value. As press >key once, it will increase by 1digit,
number will increase faster by press >key for over 2sec.
When the setting is completed, it will be saved and return to RUN mode by pressing
*key.[Fig. 5]

1ms, 20ms(Selectable)

Control
output

Output operation mode : FK, FK I

RUN
mode

12-24VDC
+
-

Sensor
12-24VDC

START
RESET

S1

INHIBIT

S2

0V

START
RESET
INHIBIT

<

Setting of

<>

T.off Time

Setting
the time

Setting of
T.on Time

<>

Setting
the time

RUN
mode

S1, S2, S3 are ON: Operating

Please use reliable contact
enough to flow 5VDC 1mA.
Be sure that it is not insulated between power input and input terminal block.

CONTACT OUT
250VAC 5A
RESISTIVE LOAD

Factory Default
NO.

Parameter

Output operation mode OUT.M

Time Range
T.RNG
Time Up/Down
U-D

2
3
(Time limit
contact 1c)

Min.input signal

Backlight
Key Lock
Setting time

6
SOURCE

Default

IN.T
BLU
LOCK
-

The above specifications are subject to change and some models may be
discontinued without notice.

ON OFF D

Ta

Ta

POWER
START

Setting time
UP
0
Setting time
DOWN
0

<

Setting of
ON.D Time

<>

Setting
the time

Setting of
OFF.D Time

OND
99.99s
UP
20
ON
L.OFF
50.00s

RELAY
OUT

Tout: Output time

Toff Ton Toff Ta

Toff Ta

Toff TonTa

Toff Ton

POWER

POWER

START
RESET

START

RELAY OUT

UP

DOWN

<>

RELAY
OUT

Toff:OFF Setting time

Ton:ON Setting time

Ton Toff Ton Toff Ta

Ton Toff Ta

Ton Ta

Ton

POWER

POWER

START
RESET

1
START

RELAY OUT

UP

RELAY
OUT

DOWN 0

Toff:OFF Setting time

Ton:ON Setting time

Ta

POWER
START
RESET

POWER

2
1

START

Setting time
UP
0
Setting time
DOWN
0

RELAY
OUT

Ta

POWER
START
RESET

POWER

2
START

Setting time
UP
0
Setting time
DOWN
0

RELAY
OUT

Ton

Toff

Ta Ta

POWER
START
RESET

Toff

Ta

Ton

Ta

Ton

Toff

POWER

2
START

RELAY OUT
Setting timeOFF Delay

UP

Setting
the time

RUN
mode

It is able to change the setting time during the time progressing, but be sure about the time
progressing while changing of the time.
If pressing *key while setting time is shorter than min. setting time, setting value will be flickering
three times and it will be returned to setting mode again, not to RUN mode.
If there is no additional key operations after entering into setting mode, it will be return to RUN mode.(Setting
value is not saved.)
Min. Setting time: 0.01 sec.(In case of OND,OND I and OND modes, it is able to set 0 since no
min. setting time is applied.)

1. Power connection
(1) AC Power : It is able to connect power to the terminals(2 to 7) without distinguish the polarity.
DC Power : Be sure the polarity of <->, <+>.
(2) It can be operating stably due to free power voltage type.(Please connect the power line
seperate from high voltage line in order to avoid inductive noise)
2. Input signal line
(1) Shorten the cable distance between the sensor and this product.
(2) Please shielded wire for input signal needed to be long.
(3) Please wire input signal line separated from power line.
3. When test dielectric voltage and insulation resistance of the control panel with this unit installed.
(1) Please isolate this unit from the circuit of control panel.
(2) Please make all terminals of this unit short-circuited.
4. Do not use this unit at below places because of product damage.
(1) Place where there are severe vibration or impact
(2) Place where strong alkalis or acids are used
(3) Place where there are direct ray of the sun
(4) Place where strong magnetic field or electric noise are generated
5. Installation environment
(1) It shall be used indoor
(2) Altitude Max. 2000m
(3) Pollution Degree 2
(4) Installation Category II

It may cause malfunction if above instructions are not followed.

RELAY
OUT

0
ON Delay

Ton:ON Setting time

Toff:OFF Setting time

1. If START signal is ON when power is on, Output will be ON when timing operation is progressed up to the Ton setting time(OnDelay). IF START signal is OFF, output will be ON when timing operation is progressed up to the Toff setting time (OFF-Delay).
2. If START signal is applied repeatedly, output is ON and display value will be reset.( position)
3. When RESET signal is ON, display value and output will be reset. When RESET signal is OFF while START signal is ON, it will
be operating as On-Delay.( position)
4. It is able to set each Toff time and Ton time separately.

[ NFD.1]
ON OFF D I

Caution for using

Q1 is ON: Operating
Q2 is ON: Operating
Sensor: NPN open collector output Sensor: NPN Universal output

Connection

POWER
START
RESET

Ton

Toff

Ta Ta Toff

POWER
START
RESET

Ta

Ton

Ta

Ton

Toff

POWER

2
START

ON Delay

Setting timeOFF Delay

RELAY
OUT

UP
0

Ton:ON Setting time

Toff:OFF Setting time

DOWN 0

0V

0V

RELAY
OUT

ON Delay

S3

Q2

START

Setting timeOFF Delay

LE4S

RESET

INHIBIT

Q1

RESET

Setting time
UP
0
Setting time
DOWN
0

RELAY OUT

Contact input

START

ON Delay

Output operation mode : ON OFF D, ON OFF D I

RUN
mode

LE4S

[ NFD]

ON OFF
Delay 1

LE4S

POWER

START
RESET

DOWN

Input connections
Sensor

Setting timeOFF Delay

Approx. 98g

LE4S is No-voltage input(Short-circuit and open) type.

Solid-state input

Ta

1. Output will be ON when START signal is ON at status of power on and Timing operation starts.
2. Output will be OFF when timing operation is progressed up to the setting time. Display value will be HOLD.
3. Even though START signal is applied repeatedly, only the initial signal is recognized.( position)
4. If START signal is ON after timing operation is progressed up to the setting time, Output will be ON and setting time
will be reset and then timing setting starts.
5. When RESET signal is ON, display value and output will be reset.( position)

ON OFF
Delay

Approval
Weight

RELAY OUT

Interval 1

Specifications
Model

POWER

1. Output will be ON when START signal is ON at status of power on and Timing operation starts.
2. Output will be OFF when timing operation is progressed up to the setting time. Display value will be HOLD.
3. When RESET signal is ON, display value and output will be reset.( position)
4. If RESET signal is OFF when START signal is ON,STEP 1will be restarted.
5. When STRAT signal is OFF, display value and output will be reset.( position)

[ INT.1]

+0.6
-0

START
RELAY
OUT

RELAY OUT

>key

Min.65

Min.65

1. If START signal is ON, output will be repeatedly ON during Ton setting time and will be OFF during Toff setting time
when power is ON.
2. Even though START signal is applied repeatedly, only the initial signal is recognized.( position)
3. When START signal is ON, display value and output will be reset. If START signal is ON, it will be restarted.
4. It is able to set each Toff time and Ton time separately. In [ FLK.1 ] mode, timing operation starts with Ton.

8 Pin socket(PG-08, PS-08): Sold separately

POWER

1. If START signal is ON, output will be repeatedly OFF during Toff setting time and will be OFF during Ton setting time
when power is ON.
2. When RESET signal is ON, display value and output will be reset.
3. If RESET signal is OFF when START signal is ON, STEP 1 will be restarted.
4. When START signal is OFF, display value and output will be reset.
5. It is able to set each Toff time and Ton time separately. In [ FLK] mode, timing operation starts with Toff.

[ FLK.1]

UP[ UP]: Time progressed from 0 to setting time.

DOWN[ DN]: Time progressed from setting time to 0.

>key

>key

76

2
1

Setting time
UP
0
Setting time
DOWN
0

[ FLK]

4) The minimum input signal setting

Dimensions

START
RESET

1. Timing operation starts when START signal is ON at status of power on.

2. Time limit output will be ON and goes OFF during Tout setting time when timing operation is progressed up to the
setting time. Display value will be HOLD.( position)
3. When RESET signal is ON, display value and output will be reset.
4. If START signal is applied while time is progressing, Timing operation will be reset and started again.( position)
5. Tout setting range: 0.01 sec~99.99 sec.

2) One-Shot output time setting

E Timer

55
48

OND II

Flicker 1

9999(4 Digit type)

Operation

RELAY OUT

S DIN W48mmH48mm

Digit

Ta

1. Timing operation starts when START signal is ON at status of power on.

2. Output will be ON when timing operation is progressed up to the setting time. Display value will be HOLD.( position)
3. Even though START signal is applied repeatedly, only the initial signal is recognized.( position)
4. When RESET signal is ON, display value and output will be reset.( position)

[ OND.2]

4)Min. input signal

Ordering information
4

ON Delay 1

* key

[ FLK], [ FLK.1],
[ NFD], [ NFD.1]
mode
5)Backlight

Caution
1.This unit shall not be used outdoors.
It may give an electric shock.
2.When wire connection, No.20AWG(0.50mm2) should be used and screw bolt on
terminal block with 0.74Nm to 0.90Nm strength.
It may result in malfunction or fire due to contact failure.
3.Please observe specification rating.
It might shorten the life cycle of the product and cause a fire.
4.Do not use the load beyond rated switching capacity of Relay contact.
It may cause insulation failure, contact melt, contact failure, relay broken, fire etc.
5.In cleaning the unit, do not use water or an oil-based detergent.
It might cause an electric shock or a fire.
6.Do not use this unit at place where there are flammable or explosive gas, humidity, direct
ray of the sun, radiant heat, vibration, impact etc.
It may cause explosion or a fire.
7.Do not inflow dust or wire dregs into inside of this unit.
It may cause a fire or mechanical trouble.

2)One-Shot output time

POWER

RELAY OUT

OND.2
mode
6)Key lock

1. Timing operation starts when START signal is ON at status of power on.

2. Output will be ON when timing operation is progressed up to the setting time. Display value will be HOLD.( position)
3. When RESET signal is ON, display value and output will be reset.( position)
4. If RESET signal is OFF while START signal is ON,STEP 1will be restarted.( position)
5. When START signal is OFF, display value and output will be reset.( position)

* key

3 sec

3 sec

1.In case of using this unit with machineries(Nuclear power control, medical
equipment,vehicle, train, airplane, combustion apparatus, entertainment or safety device
etc), it requires installing fail-safe device or contact us for information on type required.
It may result in serious damage, fire or human injury.
2.This unit must be mounted on panel.
It may give an electric shock.
3.Do not repair or checkup when power on.
It may give an electric shock.
4. Do not disassemble and modify this unit, when it requires. If needs, please contact us.
It may give an electric shock and cause a fire.

[ OND], [ OND.1],
[ OND.2], [ INT],
[ INT.1], [ OFD]
mode

Time chart( T:Setting time, T > Ta )

RELAY OUT

ON Delay

1)Time Range

Please keep these instructions and review them before using this unit.

OND

[ OND.1]

Function setting mode

Caution for your safety

Mode

[ OND]

1. If START signal is ON when power is on, timing operation starts. Output will be ON when timing operation is progressed up to the Ton setting
time(On-Delay). IF START signal is OFF, output will be ON when timing operation is progressed up to the Toff setting time (OFF-Delay).
2. Output will be ON when START signal is ON and goes OFF during setting time and display value will be reset.( position)
3. Output will be OFF when START signal is OFF and goes ON during setting time and display value will be reset.( position)
4. When RESET signal is ON, display value and output will be reset. When RESET signal is OFF while START signal is ON, it will be
operating as On-Delay.( position)
5. It is able to set each Toff time and Ton time separately.

[ OFD]
OFF D

Ta

POWER
START
RESET
RELAY OUT

OFF Delay

Setting time
UP
0
Setting time
DOWN
0

Ta

Ta

POWER
START
RELAY
OUT

1. If START signal is ON when power is on, output will be ON.

2. When START signal is OFF, timing operation starts. Output will be OFF when timing operation is progressed up to the setting time. Display value will be HOLD.
3. When RESET signal is ON, display value and output will be reset.
Reset: Up mode -> Display value is0, Output isOFF.
DOWN mode -> Display value issetting time, Output isOFF.

Major products
Photoelectric Sensors
Temperature Controllers
Fiber Optic Sensors
Temperature/Humidity Transducers
Door Sensors
SSR/Power Controllers
Door Side Sensors
Counters
Area Sensors
Timers
Proximity Sensors
Panel Meters
Pressure Sensors
Tachometer/Pulse (Rate) Meters
Rotary Encoders
Display Units
Connector/Sockets
Sensor Controllers
Switching Mode Power Supplies
Control Switches/Lamps/Buzzers
I/O Terminal Blocks & Cables
Stepper Motors/Drivers/Motion Controllers
Graphic/Logic Panels
Field Network Devices
Laser Marking System (Fiber, CO, Nd:YAG)
Laser Welding/Cutting System

http://www.autonics.com

Trusted Partner In Industrial Automation

HEADQUARTERS:
18, Bansong-ro 513beon-gil, Haeundae-gu, Busan, Korea
OVERSEAS SALES:
#402-404, Bucheon Techno Park, 655, Pyeongcheon-ro,
Wonmi-gu, Bucheon, Gyeonggi-do, Korea
TEL: 82-32-610-2730 / FAX: 82-32-329-0728
E-mail: [email protected]

EP-KE-02-057A