Siemens AG 2016

SENTRON

Power monitoring
made simple
Catalog
LV 14

Edition
2017

siemens.com/powermonitoring

 Siemens AG 2016

Related catalogs

Contents

Low-Voltage Power Distribution and

LV 10
Electrical Installation Technology
SENTRON SIVACON ALPHA
Protection, Switching, Measuring and Monitoring
Devices, Switchboards and Distribution Systems

Air circuit breakers MCCBs MCBs Residual current protective

devices / AFDDs Fuse systems Overvoltage protection
devices Switch disconnectors Switching devices
Transformers, power supply units and socket outlets Busbar
systems Measuring devices and power monitoring Monitoring
devices Software Switchboards Busbar trunking systems
System cubicles, system lighting and system air-conditioning
Distribution boards / Power distribution boards Molded-plastic
distribution systems 8WH2 spring-loaded terminals

PDF (E86060-K8280-A101-A4-7600)
PDF/print (E86060-K8280-A101-A3-7600)
Electrical Components for the
Railway Industry
SENTRON ALPHA DELTA

LV 12

Miniature circuit breakers Residual current protective

devices Fuse systems Switch disconnectors Switching
devices ALPHA FIX terminal blocks DELTA profil MediumVoltage components

LV 16

Circuit breakers Air circuit breakers/Molded case switches

Molded case circuit breakers Miniature circuit breakers Fuse
systems Switch disconnectors Switching devices Socket
outlets Busbar systems Measuring devices and power monitoring Molded-plastic distribution systems Terminal blocks

LV 52

iPo plug-in terminals iPo installation terminals

Spring-loaded terminals Combination plug-in terminals
Insulation displacement terminals Screw terminals
Accessories for terminal blocks

PDF/print (E86060-K1812-A101-A1-7600)
Components for Industrial Control
Panels according to UL Standards
SIRIUS SENTRON ALPHA

PDF/print (E86060-K1816-A101-A3-7600)
ALPHA FIX
Terminal Blocks

PDF (E86060-K1852-A101-A4-7600)
PDF/print (E86060-K1852-A101-A2-7600)

Industry Mall / TIA ST / CA 01

Catalog PDF / Response E-mail

Industry Mall
Information and Ordering Platform
on the Internet:

Catalog PDF
Digital versions of the catalogs are available in
the Information and Download Center.

www.siemens.com/industrymall

www.siemens.com/lowvoltage/infomaterial

Siemens TIA Selection Tool

for the selection, configuration and ordering of
TIA products and devices

Response E-mail
Please send your comments and suggestions
for improvement to

www.siemens.com/tst

[email protected]
(include the catalog name in the subject field)

Products for Automation and Drives

Interactive Catalog
DVD

CA 01

E86060-D4001-A510-D7-7600

Trademarks
All product designations may be registered trademarks or
product names of Siemens AG or other supplying companies.
Third parties using these trademarks or product names for their
own purposes may infringe upon the rights of the trademark
owners. Further information about low-voltage power distribution and electrical installation technology is available on the
Internet at:
www.siemens.com/lowvoltage
Siemens LV 14 2017

Technical Support
Expert advice on technical questions with a
wide range of demand-optimized services
for all our products and systems.

www.siemens.com/lowvoltage/contact

 Siemens AG 2016

Power monitoring made simple

SENTRON

Catalog LV 14 2017
Supersedes:
Catalog LV 14 2016
Refer to the Industry Mall for current updates of this
catalog:
www.siemens.com/industrymall
The products contained in this catalog can also be found in
the Interactive Catalog CA 01.
Article No.: E86060-D4001-A510-D7-7600
Please contact your local Siemens branch.
Siemens AG 2016

Printed on paper from

sustainably managed forests and
controlled sources.
www.pefc.org
The products and systems listed in this
catalog are developed and manufactured
using a certified quality management system
in accordance with EN ISO 9001:2008.

Introduction

Measuring Devices

Software

Appendix

 Siemens AG 2016

Our products lay the foundations for safe,

reliable and efficient electrical infrastructure at medium and low-voltage levels in
buildings and industrial applications.
Our portfolio includes, among other
devices, distribution boards, communication-capable protection, switching,
measuring and monitoring devices, as
well as switches and socket outlets.

Siemens LV 14 2017

Our components reliably protect against

accidents, faults and fires caused by
electricity. Furthermore, they allow
consumers to utilize electrical power in a
sustainable and responsible manner and
support automated operation of buildings
and industrial applications.
Software tools, comprehensive data
provision and professional online support
ensure efficient engineering.

 Siemens AG 2016

Electrical power distribution

integrated, safe and efficient
The increasing level of automation in buildings and industry introduces novel
requirements for electrical power distribution and make the underlying technologies ever
more complex. Our components and systems are perfect for integration into networked
environments and significantly increasing the efficiency of your business processes:
communication-capable, flexible and failsafe devices combine with digital engineering to
enable optimized solutions - for any application.

Solutions for the future

Comprehensive support

We support you throughout the entire

value chain with our end-to-end portfolio,
from the planning stages right through to
the operation, as well as when it comes to
measures for modernizing and expanding
your electrical energy distribution systems.

At the same time, you benefit from our

broad portfolio of personalized and
automated maintenance and support
services.

Our tested and certified components,

systems and software packages allow for
ever-suitable and efficient solutions in both
centralized and distributed power systems
the world over and can be perfectly
integrated into building automation and
industrial automation applications.

Clear ordering channels, transparent

product availability data and high delivery
reliability coupled with swift global spare
part provision, comprehensive online
services, expert consulting and fast,
efficient and reliable processes ensure that
you are optimally covered throughout the
entire product life cycle.

Siemens LV 14 2017

 Siemens AG 2016

Planning Efficiency

Overview
With Planning Efficiency, Siemens supplies answers to typical
questions that often present themselves in electrical
planning:
What is the appropriate product for my application?
Where can I find product data?
How can I make processes more efficient and save more
time?
The entire electronic support offered by Siemens is merged
under Planning Efficiency. At each phase of the project,
online functions make the everyday work of the planners
easier and more efficient. Planning Efficiency focuses on
optimizing the control cabinet configuration among other
things.
Especially in this early phase, up to 80% of time and costs
can be saved.

IC01_00205a

In order to supply the planners with all they need and to

simplify the modern electrical planning of every aspect of the
control cabinet configuration, the electrical support of
Planning Efficiency focuses on four benefits:
Finding the right product faster using intuitive product
selection
Time savings of up to 80% with universal product data for
your CAE and CAD systems
User-friendly compilation of project-specific
documentation
Comprehensive support at any time, whatever your
location

Siemens LV 14 2017

 Siemens AG 2016

Process phases
At each phase of the process, Siemens provides
comprehensive online functions free of charge.

Concept &
selection

Mechanical
design

This ensures that all the necessary information and product

data are available around the clock at any location
worldwide.
Electrical
design

Plant
documentation

Installation / service /
commissioning /
diagnostics

Ordering

Configurators for products and systems

With just a few mouse clicks, you will find yourself guided by
the configurator to a suitable product or system. Simply enter
the relevant parameters and select your individual solution.
CAx Download Manager

My Documentation Manager
To provide support when creating the plant documentation,
we have developed a manual configurator.
My Documentation Manager enables you to assemble the
standard-compliant plant documentation individually with just
a few clicks of the mouse. Simply select the required sections
from the existing manuals of the installed Siemens products.
EPLAN Electric P8 Macro a big plus for EPLAN users
Using the EPLAN Electric P8 Macro in .edz exchange format
(EPLAN Data Archived Zipped) the overall time required for
data integration can be further reduced. With just a few
clicks, the data types for any number of article numbers can
be imported and combined. In this way, it is possible for the
installed Siemens products to be displayed across different
pages of the circuit diagram quickly and easily.

The configurator supplies the appropriate 3D models and dimension

drawings for the control cabinet construction diagram.
IC01_00265

The CAx Download Manager can supply you with all the
necessary CAx file types for the products of your choice for
use in all common CAE and CAD systems. The data
contained in the files is continuously updated. The whole
process involves only four selection steps and is free of
charge. All the files you select will then be compiled into a zip
file and made available for you to download for further use.
This results in a time saving of up to 80% because there is no
need for manual data collection thanks to the universal
manufacturer data for all commonly used CAE and CAD
systems.

Internal circuit
diagrams

Dimensional
drawings

Operating
instructions

Connection
diagrams

3D models

Product images

Product
master data

Manuals

Data sheets

Characteristic
curves

Certificates

EPLAN Electric
P8 Macros

The CAx Download Manager makes 11 universal data types

available, as well as the EPLAN Electric P8 macro.
Internal circuit diagrams
Connection diagrams
Product master data
Operating instructions

At a glance
Without Planning Efficiency a lot of time would often be lost
due to manual data transmission. Now you are able to
concentrate on the essentials. All necessary information and
product data is provided by Siemens for easy retrieval.
This makes the control cabinet configuration process more
efficient and simplifies your everyday work.

Product images
Data sheets
IC01_00264

The EPLAN Electric P8 macro in .edz exchange format offers even

more compared to the .ema exchange format.

For more information, go to

www.siemens.com/planning-efficiency.

Planning Efficiency
Find out more about Planning Efficiency
in our informative videos

Siemens LV 14 2017

 Siemens AG 2016

Technical Support
The Technical Support for low-voltage power distribution and electrical installation
technology assists you with all your technical queries about our products and
systems both before and after delivery.

Or

de

Competent and fast

specialist advice on:

ri

Technical
Support

Co

atio

mm
Se

r vi

ce

O p e r at i

Product selection
Commissioning
Issues during operation
Possible special versions
Special requirements
Product features
Device communication

on
I201_19185

Pl a
nn
in

uration
nfig

ng

Infor m

Our experts will help

you with competent
specialist support

Co

is sio nin g

Still have
questions?

Get all the information you need with just one click
Industry Online Support get up-to-date information online fast
www.siemens.com/online-support

In the Product Support area, you will find FAQs, manuals, certificates,
applications & tools etc.
www.siemens.com/lowvoltage/product-support

Support Request the quickest route to the experts

www.siemens.com/lowvoltage/technical-support

Using the Support Request form on the Industry Online Support portal,
you can send your query directly to our Technical Support team.

Conversion tool the easy and efficient way of finding successor

products
www.siemens.com/conversion-tool

The benefits for you

Response within 4 hours in 93% of cases
Direct support from an experienced team of engineers
and technicians

Siemens LV 14 2017

 Siemens AG 2016

SITRAIN Training for Industry

With SITRAIN, you benefit from practical training directly from the manufacturer.
Our certified trainers are active in more than 60 countries and can help you and
your employees develop their skills.

Competence through training

Information on our training courses
can be found at
www.siemens.com/lowvoltage/training

Requirement for taking part in the courses:

Basic principles of electrical engineering and power distribution
I201_19565

Circuit breaker courses

LV-CBMAIN
Maintenance and operation of
SENTRON 3WL circuit breakers:
2 days

d
LV-CBPROJ
Basic principles of configuring and
selecting SENTRON circuit breakers:
1 day

LV-CBCOM
Communication with
SENTRON components: 1 day

LV-SENVER
Advanced course on
SENTRON products: 1 day

Power monitoring courses

LV-EMSENTB
Energy management (Basic): 2 days

LV-EMSENTE
Energy management (Expert): 1 day

Switchboard courses
LV-ALPHAPB
ALPHA 3200
Switchboard installation: 1 day
LV-ALPHATA
ALPHA 3200
Technology and software: 1 day

LV-SIVAS4
SIVACON S4
Power distribution boards: 2 days

The benefits for you

Flexible plant adaptation
to market requirements
Ensuring quality
standards in production
Reliable engineering and
commissioning
Shorter commissioning,
maintenance and service times
Exclude expensive faulty
planning right from the outset
Reduce downtimes and
rectify faults more quickly

Siemens LV 14 2017

 Siemens AG 2016

Still have questions?

Get all the information you need
with just one click
Always here for you: our comprehensive support

Information

Planning/order

Operation/service

Training

Website

Industry Mall

SITRAIN Portal

Catalogs and brochures

Configuration

Siemens Industry
Online Support (SIOS)

Newsletters
Image database

SIMARIS planning tools

CAx-Download Manager

My Documentation Manager

Siemens Power Academy

BT Academy

Technical support
Support request
I201_19079

We support you from the planning stages to commissioning to operation.

siemens.com/lowvoltage

Siemens LV 14 2017

Siemens AG 2016

Introduction

1/2
1/3
1/6
1/9
1/11

Power monitoring system

Power management
in accordance with ISO 50001
Hardware and software components
PC-based power monitoring system
SIMATIC-based power data
management system

For further technical

product information:
Siemens Industry Online Support:
www.siemens.com/lowvoltage/
product-support
Entry type:
Application example
Certificate
Characteristic
Download
FAQ
Manual
Product note
Software archive
Technical data

Siemens LV 14 2017

 Siemens AG 2016

Introduction

Power monitoring system

Overview

Power monitoring made simple

Simplified installation, a wide range of measuring devices, and easy-to-use software: the system from the SENTRON portfolio is optimally suited for small and
medium-sized businesses in industry and infrastructure.

Advantages of our power monitoring system

A scalable system

Industrie 4.0 and smart buildings

The power monitoring system requires no

expert knowledge for commissioning and is
available in small, entry-level starter
packages. Both hardware and software can
be easily.

Its not just large companies but SMEs as well that

can benefit from digitalization and automation
without incurring high procurement costs. Our
power monitoring system gathers the data.

Focus on power quality

Audits and standards

A decreasing power quality can cause

malfunctions in production facilities and
terminal equipment. Our power monitoring
system analyzes power quality, thus ensuring
higher plant availability.

1/2

Siemens LV 14 2017

ISO

50001

Companies have to deal with laws and regulations

governing energy efficiency. Our power monitoring
system has been certified by the German TV, thus
providing the basis for energy management in
conformance with requirements.

 Siemens AG 2016

Introduction
Energy management in accordance with ISO 50001

Overview
A systematic approach to energy efficiency
The ISO 50001 standard supports companies with a specific
process description for introducing a corporate energy management system. Standard-compliant energy management optimizes energy utilization, while continuously enhancing energy
efficiency.
Defining energy policy objectives
A central management task is the formulation of an in-house
energy policy. It defines relevant strategic and operational
objectives. Ongoing planning will include the identification of
additional optimization potential for the business areas under
scrutiny, and the development of relevant improvement
measures.
Introducing process optimization
As a first step, an energy manager must be identified and
nominated. He will then evaluate captured data, and derive and
implement appropriate optimization measures. He will report the
achieved results to corporate management.
Making energy flows transparent
Power management is a matter for decision at the top level

Responsible use of valuable energy resources

Global climate change, scarce energy resources and the
increasing demand for energy mean that there is an urgent need
for action. The industrialized nations have therefore committed
to continuously reduce their annual C02 emissions by 2020. The
European Council has set a target of improving energy efficiency
by 20 percent by 2020. ln Germany, the aim is to reduce energy
consumption compared with 2008 by 10 percent by 2020, and
by 25 percent by 2050.
The international standard ISO 50001 specifies the basic conditions for establishing a corporate energy management system
for improved energy efficiency and sustained reduction in a
company's energy consumption. Our TV-certified power monitoring system from the SENTRON portfolio provides the technical foundation for this. It enables energy flows to be recorded,
visualized and analyzed to derive specific measures for
optimizing energy use.

As a second step, basic energy consumption and cost data, as

well as information on in-house energy production, must be
collected and documented clearly and verifiably. This requires
the development of a reliable and precise system for the capture
and analysis of consumption data. The objective is to recognize
sustainable savings potential, to derive appropriate measures
for that potential, and to implement these measures systematically.
Periodic controlling
Periodic checks will ensure that your energy management
system functions correctly, and that objectives are reached.
Corrective and preventative measures can then be implemented
as needed.

Energy policy objectives

Process optimization

Strategic
Operational

Introduction
Implementation
Continuous
improvement due to
energy management
acc. to ISO 50001

Corrective measures
Preventative measures

Periodic controlling

Monitoring
Measuring
Analysis

Consumption data capture/analysis

Introduction of a corporate energy management system in accordance with ISO 50001 for continuous improvement of energy efficiency by reducing
energy consumption and costs.
Siemens LV 14 2017

1/3

 Siemens AG 2016

Introduction
Energy management in accordance with ISO 50001
Providing the basis with power monitoring
The power monitoring system from the SENTRON portfolio is
suitable for infrastructure, industrial applications, and buildings.
The 7KT/7KM PAC measuring devices record the data of
outgoing feeders or individual loads.
The 3WL/3VA/3VL circuit breakers supply measured values and
important information for diagnostics, fault detection, and maintenance via standardized bus systems.
With the powermanager power monitoring software, the
recorded measured values can be easily visualized, analyzed,
archived, and monitored.

Recording of generated energy using

MID measuring devices

7KT
PAC1500

Derivation of optimization measures through

transparency of the energy flows

7KM
PAC3200

7KT
PAC1500

powermanager

Increased availability of energy through

monitoring of critical states in the power
supply

7KM
PAC3100

Impuls

Modbus RTU

7KM
PAC4200

Increased system availability through

continuous monitoring of switching states

Industrial Ethernet
(Modbus TCP)

7KM
PAC42

3WL
ACB

3VA
MCCB

7KM
PAC4200

Increased productivity through optimization

of energy consumption and energy costs
PROFIBUS
PROFINET

S7 1500

7KM
PAC3200

Transparency at the infeed thanks to

seamless recording of the power supply
quality

7KM
PAC5200

1/4

Siemens LV 14 2017

7KM
PAC5100

I201_19212

 Siemens AG 2016

Introduction
Energy management in accordance with ISO 50001
Continuously increasing energy efficiency
Precise cost center accounting for consumers
Precise allocation of energy costs to cost centers
Benchmarking between different cost centers
Increased energy awareness

Detection of energy guzzlers, reduction of load peaks

Detection of energy-intensive processes and loads
Cost savings created by amending the power supply agreement
Tax savings by seamless documentation of application-specific consumption

Protection of sensitive areas for high plant safety

Avoidance of equipment failures due to overload
Protection of sensitive devices against harmonics
Early intervention possible by means of notifications

Monitoring of protective devices for high system availability

Increased system availability
Optimization of maintenance
Fast response to service call-outs

Multi-site power monitoring

Centralized, multi-site power monitoring via standard IT networks
Benchmarking of various corporate units increases energy awareness
Improvement of power supply conditions by bundling supply volumes

Siemens LV 14 2017

1/5

 Siemens AG 2016

Introduction

Hardware and software components

Overview
Measuring devices and circuit breakers
7KT PAC1200

7KT PAC1500

7KM PAC3100

7KM PAC3200

The entry-level
solution when it
comes to energy
measurement

The cost-effective
solution for digital
measurement

The specialist
solution for precise
energy measurement

Measuring range/connection
Max. input voltage L-L/L-N

400 V/230 V

400 V/230 V

480 V/276 V

690 V/400 V1)

Transformer connection version

x/5 A

x/5 A

x/5 A

x/1 A/x/5 A

Direct connection version

40/63 A

80 A/125 A

DC power supply unit with extra-low voltage version

22 ... 65 V

Single-phase counter version

Electrically isolated voltage inputs

Variant without display (with web server)

2)

II

II

II

II

Distortion factor THD (voltage, current)

3)

Harmonics (voltage, current)

Phase angle/phase chart

Load profile record with time stamp for min/max values

Flicker acc. to IEC 61000-4-15

Operating hours counter

Limit monitoring

Logic functions

Event log

Gateway function

Reporting acc. to EN 50160

Integrated fault recorder

Digital inputs/digital outputs

2/2

1/1

S0 interface

4DI/2DO expansion module

M-Bus

Optional

Instabus KNX

Optional

Modbus RTU

Optional

Optional

Ethernet with Modbus TCP

PROFIBUS DPV1

Optional

PROFINET IO/ PROFIenergy

Optional

Parameterization software

powerconfig

powerconfig,
TIA-Portal V14

Integration of power monitoring system

powermanager

powermanager

powermanager

powermanager
SIMATIC EnergySuite

Web servers

Measuring accuracy, active energy, reactive energy

1I2

1I3

0.5 S I 2

MID version

Installation

Std. mount. rail.

Std. mount. rail.

Front mounting

Front mounting

Dimensions in MW (1 MW = 18 mm) or in mm

4 MW

2 / 4 / 6 MW

96 96 56

96 96 56

Measured quantities
Voltage, current, power, frequency, power factor
Energy measurement
Apparent, active, reactive energy
Extended measured quantities

Monitoring functions

System integration and communication

General dataGeneral data

1)

With the exception of devices with power supply units with extra-low
voltage

2)

On the display energy and power values only. Additional measured

quantities are transmitted via optional expansion modules 7KT Modbus /
7KT M-Bus

3)

THD indication

1/6

Siemens LV 14 2017

4)

Measuring accuracy including current transformer

5)

DSP800, see Catalog LV 10, chapter "Molded Case Circuit Breakers"

Available / possible -- Not available / not possible

 Siemens AG 2016

Introduction
Hardware and software components

7KM PAC4200

7KM PAC5100

7KM PAC5200

3WL

3VA ETU8

The professional solution

The specialist solution
The expert solution
for communication/monitoring for measured value recording for power supply quality

The specialist solution

for protection and energy
measurement

The specialist solution

for protection and energy
measurement

690 V/400 V1)

690 V/400 V

690 V/400 V

690 V/400 V

690 V/400 V

x/1 A/x/5 A

x/1 A/x/5 A

x/1 A/x/5 A

Integrated

Integrated

22 ... 65 V

24 V

24 V

II

II

II

II

II

3. ... 31.

2. ... 40.

2. ... 40.

> 4000 events

2/2

0/2

0/2

Optional

Optional

Optional

Optional

Optional

Optional

Optional

Optional

Optional

Optional

Optional

Optional

Optional

Optional

powerconfig,
TIA-Portal V14

powerconfig

powerconfig

powerconfig

powerconfig,
TIA-Portal V14

powermanager
SIMATIC EnergySuite

powermanager

powermanager

powermanager

powermanager
SIMATIC EnergySuite

a
0.2 S I 2

0.5 S I 2

0.5 S I 2

2 S I 24)

2 S I 24)

Front mounting

Front installation/standard rail

See LV 10

See LV 10

96 96 82

96 96 100

96 96 825)

96 96 825)

96 96 100

Siemens LV 14 2017

1/7

 Siemens AG 2016

Introduction

Hardware and software components

Accessories for 7KT PAC measuring devices

7KT PAC expansion modules

Specification

7KT LAN couplers

M-Bus

Modbus RTU

RS 485

KNX

Web servers

Up to 9600 bit/s

Up to 115200 bit/s

For connection to the

7KT LAN coupler

Up to 19200 bit/s

For up to 30
7KT PAC1500
measuring devices

Accessories for 7KM PAC measuring devices

7KM PAC expansion modules

Standard mounting
rail adapter

Switched Ethernet

PROFIBUS DP

RS 485

4DI/2DO

7KM PAC TMP2

for 7KM PAC3200,

7KM PAC4200
and 3VA
COM100/COM800

for 7KM PAC3200,

7KM PAC4200
and 3VA
COM100/COM800

for 7KM PAC3200,

7KM PAC4200
and 3VA
COM100/COM800

for 7KM PAC4200

(number of digital
inputs/outputs per
module 4/2)

For 7KM
PAC3100/3200/4200
for mounting on a
standard mounting rail

Protocol

PROFINET IO
PROFIenergy
Modbus TCP

DPV1

Modbus RTU

S0 interface

--

Maximum number of
connectable expansion
modules of the same type

--

The powerconfig software for commissioning

Software tool for efficient commissioning and diagnosis of communication-capable SENTRON components
License

Free use

Supported devices

7KM PAC3100/3200/4200 measuring devices, incl. expansion modules

3WL/3VL/3VA/ATC5300 circuit breakers

General range of functions

The PC-based tool facilitates parameterization of the devices, resulting in substantial time savings, particularly when several
devices have to be set up.
The device settings can be stored in the PC and printed out.
The tool enables monitoring of instantaneous measured quantities, which can be printed out if required. Execution of specific
device functions, such as resetting of devices and setting of energy counters.

Supported languages

German, English, Chinese, Spanish, Portuguese

Service functions

Firmware updates and switching of language packs for 7KM PAC measuring devices

Functional scope with

7KM PAC4200 and 3VA

Readout of data stored in the device (events; load profile history; daily energy counters), saved in csv format

Setting of parameter values

Display of actual measured quantities

For more information about powerconfig, see chapter "Software"

1/8

Siemens LV 14 2017

Display of the circuit breaker state

 Siemens AG 2016

Introduction
PC-based power monitoring system

Overview

Hardware components of the PC-based power monitoring system

Software component of the power monitoring software: powermanager

Power monitoring system with SENTRON components

Features of the powermanager power monitoring software

The TV-certified power monitoring system from the SENTRON

portfolio consists of the 7KT/7KM PAC measuring devices, the
3WL/3VA/3VL circuit breakers, and the powermanager power
monitoring software. This forms the technical basis for
supporting a corporate energy management system as specified by ISO 50001.

The powermanager power monitoring software constitutes the

optimum technical basis for supporting a corporate power
monitoring system as specified by ISO 50001 and EN 16247:
Independent power monitoring software
Can be operated using a Windows PC and measuring devices
with Ethernet connection
Easy getting started with basic license (Basic Package), can
be extended with flexible licensing concept according to
customer requirements
Fully scalable, relative to number of devices and software
functions
Optimum integration of 7KT/7KM PAC measuring devices,
3WL/3VL/3VA circuit breakers, 7KM PAC 5200 power quality
devices and and any other Modbus devices
Support of the various device and communication interfaces
(Modbus RTU, Modbus TCP)
Status display of devices
Available languages: German, English, Spanish, Portuguese,
Italian, French, Turkish, Chinese

The hardware and software components are optimally coordinated with each other. For example, special drivers for the
SENTRON devices are integrated in the powermanager power
monitoring software. They enable energy data to be captured
without any great configuration effort and they indicate the key
measured values or the status by means of predefined views.
This reduces the engineering overhead. The device functions
are optimally supported in the software.

Siemens LV 14 2017

1/9

 Siemens AG 2016

Introduction

PC-based power monitoring system

Application
Industries
An energy-efficient production system enhances both the image
and the productivity of a company, and thus its competitiveness.
Power monitoring as the technical basis for energy management
for increasing a company's energy efficiency is thus of interest
to all areas, from industrial applications to infrastructure, and
buildings in the service sector.

System configuration
Integration of measuring devices by means of predefined
device templates for the 7KT/7KM PAC measuring devices
and the 3WL/3VA/3VL circuit breakers
Integration of existing Modbus-capable detecting devices is
easy
Communication through Standard Ethernet
Integration of devices with RS 485 interface (ModbusRTU)
through Modbus gateway, e.g. the 7KM PAC4200 measuring
device can be used as the gateway

System configuration
Operation & monitoring
Windows or Web clients

Ethernet
Data processing
Server

powermanager power
monitoring software

7KT PAC1200
Multichannel
current measuring
system

3VA-line
3VA molded
case circuit
breakers

I202_01389

Ethernet (Modbus)

Data detection
Measuring/
protection
COM 800
devices

...

7KM PAC3100
measuring
device

7KM PAC5200
measuring
device
Modbus RS485
7KT PAC1500
measuring
device

7KM PAC5100
measuring
device
3WL air
circuit
breakers

7KM PAC4200
measuring
device

7KM PAC3200
measuring
device

COM 100

3VA-line

max. 8

3VA
molded case
circuit
breakers

Typical topology of a power monitoring system

More information
Hardware of the PC-based power monitoring system

TV certification

TV-tested
according to ISO 50001
> Learn more
The TV certificate is available from
www.siemens.com/tuev-certificate-of-conformity

The hardware components of the PC-based power monitoring

system are
7KM PAC measuring devices; see chapter "Measuring
Devices"
3WL air circuit breakers; see Catalog LV 10, chapter
"Air Circuit Breakers"
3VL molded case circuit breakers; see Catalog LV 10, chapter
"Molded Case Circuit Breakers"
3VA molded case circuit breakers; see Catalog LV 10, chapter
"Molded Case Circuit Breakers"
Software of the PC-based power monitoring system
The software of the PC-based power monitoring system is
powermanager; see chapter "Software".
Powermanager system packages with software and hardware
are an easy and low-cost way to get started with a power monitoring system; see chapter "Software".
Internet
You can find more information on the Internet at:
www.siemens.com/powermonitoring

1/10

Siemens LV 14 2017

 Siemens AG 2016

Introduction
SIMATIC-based power data management system

Overview
Operating and
monitoring level
Archive

PROFINET
Industrial Ethernet

SIMATIC PCS 7 / WinCC,

Option powerrate and function block libraries

Processing level

SIMATIC S7

PROFINET /
PROFIenergy

PROFIBUS DP

Industrial Ethernet
Distributed
I/O, e.g.
ET200

7KM PAC3200
7KM PAC4200
measuring
devices

COM100

SIMOCODE
pro motor
management
system

COM800

3VA-line

Acquisition and
control level

3VA-line

COM15
Analog and digital signals
from contactors, counters,
flow meters

SINAMICS
G120 frequency
converters

...
3VA

3VA

NSH0_00060g

3VA

max. 8
3WL

SIMATIC-based solutions for the process and manufacturing

industry
A key feature of the process and manufacturing industry is
frequently high energy consumption. It therefore makes sense to
integrate a power data management system in existing systems.
Communication via PROFIBUS DP
PROFIBUS DP enables integration of a wide range of devices:
For the protection of distribution boards and loads:
Protective devices, such as circuit breakers
For open-loop and closed-loop control: Frequency
converters, motor management systems and soft starters
For detection
- Electrical measured quantities: Via the measuring devices
7KM PAC3200/4200
- Non-electrical measured quantities: Via analog/digital
converters

PROFINET and PROFIenergy

An increasing number of devices in automation technology offer
PROFINET. The 7KM PAC Switched Ethernet PROFINET expansion module enables the 7KM PAC3200/PAC4200 measuring
devices and 3VA circuit breakers to be connected to the automation systems.
PROFIenergy is a "Common Application Profile" from Profibus
International. Thanks to PROFIenergy it is possible to create a
power data management system with standardized device interfaces.
Function block libraries for SIMATIC PCS 7 and WinCC
The function block library for SIMATIC PCS 7 and WinCC
ensures device integration as follows:
Measured quantities and states can be connected via CFC
Structured display of measured quantities and protection
parameters for the 3WL/3VA/3VL circuit breakers.
Limit value violations are displayed, archived and acknowledged in the relevant communications system in the usual
way
Circuit breakers can be program-controlled or manually
operated with the appropriate user authorization

Siemens LV 14 2017

1/11

 Siemens AG 2016

Introduction

SIMATIC-based power data management system

Benefits

More information

Increased energy efficiency due to precise knowledge of the

load profile
Optimization of power supply agreements
Allocation of power costs to cost centers
Optimization of plant maintenance
Identification of critical plant conditions
Reliable monitoring of the power limit through automatic load
management

Application
The SIMATIC-based power data management system is used in
all industries in which PCS 7 and WinCC are used, and the transparency and monitoring of power flows is crucial.

Hardware components
The hardware components of the SIMATIC-based power data
management system are
7KM PAC measuring devices; see chapter "Measuring
Devices"
3WL air circuit breakers; see Catalog LV 10, chapter
"Air Circuit Breakers"
3VL molded case circuit breakers; see Catalog LV 10, chapter
"Molded Case Circuit Breakers"
3VA molded case circuit breakers; see Catalog LV 10, chapter
"Molded Case Circuit Breakers"
Software components
The software components of the SIMATIC-based power data
management system are
Library 7KM PAC3200 for SIMATIC PCS 7
Library 7KM PAC3200 for SIMATIC WinCC
For information about all the software components, see chapter
"Software"
Internet
You can find more information on the Internet at:
www.siemens.com/powermonitoring

1/12

Siemens LV 14 2017

Siemens AG 2016

Measuring Devices

2/2
2/4
2/5
2/7
2/9
2/10
2/12
2/13

7KM PAC measuring devices

Introduction
7KM PAC3100 measuring devices
7KM PAC3200 measuring devices
7KM PAC4200 measuring devices
7KM PAC5100 measuring devices
7KM PAC5200 measuring devices
Accessories for 7KM PAC
7KM PAC expansion modules

2/25
2/26

7KT PAC measuring devices

Introduction
7KT PAC1200 multichannel current
measuring system
7KT PAC1500 three-phase
measuring devices
7KT PAC1500 single-phase
measuring devices
7KT PAC expansion modules
7KT LAN couplers

2/28
2/29
2/32

Accessories
Introduction
4NC current transformers
7KT12 current transformers

2/16
2/17
2/22
2/24

Weitere technische
Produkt-Informationen:
Configuration Manual
Measuring Devices and Power Monitoring
Article No.: 3ZW1012-7KM42-0AC1
Siemens Industry Online Support:
www.siemens.com/lowvoltage/
product-support
Beitragstyp:
Anwendungsbeispiel
Download
FAQ
Handbuch
Kennlinie
Produktmitteilung
Software-Archiv
Technische Daten
Zertifikat

Siemens LV 14 2017

 Siemens AG 2016

Measuring Devices
7KM PAC Measuring Devices
Introduction

Page

Application

Standards

Used in

Industry

Devices

Residential
buildings

Non-residential
buildings

Overview

Control panel instrument with graphics display,

integrated digital inputs and outputs and an RS 485
interface for the transmission of measured values
and configurations.

Measuring
accuracy for
energy acc. to
IEC 61557-12

--

Measuring
accuracy for
energy acc. to
IEC 62053-22/23
and
IEC 61557-12

--

Measuring
accuracy for
energy acc. to
IEC 62053-22/23
and
Display of over 200 electrical measured values for IEC 61557-12
switchboard assemblies, infeeds or outgoing
feeders. Extensive functions for precise energy
measurement for power import and feedback and
assessment of the system quality.

--

Measuring
accuracy for
energy acc. to
IEC 62053-22/23
and
IEC 61557-12

--

Measuring
accuracy for
energy acc. to
IEC 62053-22/23
and
IEC 61557-12

--

7KM PAC measuring devices

7KM PAC3100 measuring device 2/4
AC/DC wide-range power supply
unit, screw connection

Display of 30 electrical measured values and

consumption values in switchboard assemblies,
infeeds or outgoing feeders.
International standards and multi-lingual displays
for worldwide use.
7KM PAC3200 measuring device 2/5
3 versions:
AC/DC wide-range power supply
unit, screw connection
DC power supply unit with extralow voltage, screw connection
AC/DC wide-range power supply
unit, ring cable lug connection

Control panel instrument with graphics display,

integrated digital inputs and outputs and an integrated Ethernet interface for the transmission of
measured values and configurations.
Display of over 50 electrical measured values for
switchboard assemblies, infeeds or outgoing
feeders. Dual-tariff measuring devices for precise
energy measurement for power import and feedback.
The following expansion modules are available:
7KM PAC Switched Ethernet PROFINET
7KM PAC RS 485
7KM PAC PROFIBUS DP

7KM PAC4200 measuring device 2/7

3 versions:
AC/DC wide-range power supply
unit, screw connection
DC power supply unit with extralow voltage, screw connection
AC/DC wide-range power supply
unit, ring cable lug connection

Control panel instrument with graphics display,

user-defined displays, memory, clock and calendar
function, digital inputs and outputs and an integrated Ethernet interface with gateway function to
transfer measured values and configurations.

The following expansion modules are available:

7KM PAC Switched Ethernet PROFINET
7KM PAC RS 485
7KM PAC PROFIBUS DP
7KM PAC 4DI/2DO
7KM PAC5100 measuring device 2/9
2 versions:
Control panel instrument with
graphics display
Standard rail instrument without
display

Control panel instrument with graphics display and

user-defined displays, or instrument for standard
rail mounting in accordance with EN 60750, web
server for parameterization, visualization and data
management, 2 binary outputs, electrically isolated
voltage inputs, synchronization via internal RTC
clock or externally via NTP, 4 freely parameterizable LEDs for device status or limit violations, as
well as integrated RJ45 Ethernet interface.
Recording of more than 250 electrical measured
values for switchboard assemblies, infeeds or
outgoing feeders, extensive functions for precise
energy measurement for power import and feedback, and for assessment of the system quality.

7KM PAC5200 measuring device 2/10

2 versions:
Control panel instrument with
graphics display
Standard rail instrument without
display

Control panel instrument with graphics display and

user-defined displays or instrument for standard rail
mounting in accordance with EN 60750, web
server for parameterization, visualization and data
management, 2 binary outputs, electrically isolated
voltage inputs, flicker in accordance with
IEC 61000-4-15, synchronization via internal RTC
clock or externally via NTP, 4 freely parameterizable LEDs for device status or limit violations, 2 GB
memory, integrated fault recorder, reporting in
accordance with EN 50160, rms recorder, as well
as integrated RJ45 Ethernet interface.
Recording of more than 250 electrical measured
values for switchboard assemblies, infeeds or
outgoing feeders. Extensive functions for precise
energy measurement for power import and feedback and assessment of the system quality.

2/2

Siemens LV 14 2017

 Siemens AG 2016

Measuring Devices
7KM PAC Measuring Devices
Introduction

2/13

Standards

The 7KM PAC Switched Ethernet PROFINET

IEC 61784-2
expansion module is used to connect the
7KM PAC3200 and 7KM PAC4200 measuring
devices and 3VA molded case circuit breakers to
Switched Ethernet PROFINET (PROFIenergy).

Used in

2
Industry

7KM PAC expansion modules

Application

Residential
buildings

Page

Non-residential
buildings

Devices

--

The 7KM PAC PROFIBUS DP expansion module is IEC 61158

used to connect the 7KM PAC3200 and
7KM PAC4200 measuring devices and
3VA molded case circuit breakers to
PROFIBUS DPV1
The 7KM PAC RS 485 expansion module is used RS 485
to connect simple devices with RS 485 interface,
such as the 7KM PAC3200 and 3VA molded case
circuit breaker, and supports the Modbus RTU
protocol.
The 7KM PAC 4DI/2DO expansion module is used IEC 62053-31
to expand the 7KM PAC4200 measuring device to
up to 10 digital inputs and 6 digital outputs.

Siemens LV 14 2017

2/3

 Siemens AG 2016

Measuring Devices
7KM PAC Measuring Devices
7KM PAC3100 measuring devices

Overview

Benefits
Simple mounting and commissioning
High IP65 degree of protection (front side, when installed)
permits usage in extremely dusty and wet environments
Intuitive operation using 4 function buttons and multilingual
plain text displays
Easy adaptation to different systems using integrated and
optional
- Digital inputs and outputs
- Communication interfaces
Worldwide use
- At least 8 languages
- International approvals
- Developed and tested to European and international
standards
Low mounting depth
User-friendly, free configuration software powerconfig;
see below

The 7KM PAC measuring devices are used to measure and

display all relevant system parameters in low-voltage power
distribution. They can be used for both single-phase and multiphase measurements in 3 and 4-conductor power supply
systems (TN, TT, IT).
They record energy values for main distribution boards,
electrical branches or individual loads precisely and reliably,
and also supply key measured values for assessment of the
state of the plant and the quality of the power supply.
The 7KM PAC3100 measuring device is fitted with an integrated
Modbus RTU interface via RS 485, no expansion module is
required.

Selection and ordering data

Version

DT Article No.
www.siemens.com/
product?Article No.

PU
(UNIT,
SET, M)

PS*/
P. unit

PG

Weight
per PU
approx.
kg

7KM PAC3100 measuring device

Screw connection

Control panel instrument, 96 x 96 mm

Screw connections for connecting current and
voltage

7KM3133-0BA00-3AA0

1 unit

1DD

0.459

NSG0_00230

AC/DC wide-voltage power supply unit

UAUX:
100 240 V AC 10 %, 50/60 Hz
110 250 V DC 10 %
Measuring inputs
Ue: max. 480/277 V 3 AC, 50/60 Hz
Ie: /5 A

7KM3133-0BA00-3AA0

More information
For current transformers, see page 2/29 or
Catalog LV 10, chapter "Switch Disconnectors"
For other accessories, see page 2/28
powerconfig is available free of charge at
http://support.automation.siemens.com/WW/view/en/63452759
For more information about powerconfig, see chapter "Software"

2/4

Siemens LV 14 2017

* You can order this quantity or a multiple thereof.

 Siemens AG 2016

Measuring Devices
7KM PAC Measuring Devices
7KM PAC3200 measuring devices

Overview

Benefits
Simple mounting and commissioning
High IP65 degree of protection (front side, when installed)
permits usage in extremely dusty and wet environments
Intuitive operation using 4 function buttons and multilingual
plain text displays
Easy adaptation to different systems using integrated and
optional
- Digital inputs and outputs
- Communication interfaces
Worldwide use
- At least 8 languages
- International approvals
- Developed and tested to European and international standards
Low mounting depth

The 7KM PAC measuring devices are used to measure and

display all relevant system parameters in low-voltage power
distribution. They can be used for both single-phase and multiphase measurements in 3 and 4-conductor power supply
systems (TN, TT, IT).
They record energy values for main distribution boards, electrical branches or individual loads precisely and reliably, and
also supply key measured values for assessment of the state of
the plant and the quality of the power supply.
The 7KM PAC3200 measuring device is fitted with an integrated
Modbus TCP interface via Ethernet, no expansion module is
required.

Additional performance characteristics of the 7KM PAC3200

Precise energy measurement
Versatile system integration
- Integrated Ethernet interface
- Optional communication modules available
- Multifunctional digital inputs and outputs
- Limit monitoring
Can be directly connected to power supply networks up to
690 V AC (UL-L), CATIII without voltage transformer
(with the exception of devices with power supply units with
extra-low voltage)
User-friendly configuration software powerconfig;
see chapter "Software"

Power distribution in the TIA Portal

The devices fit seamlessly into V14 or higher of TIA Portal, thus
enabling parameter assignment, commissioning and automation of power distribution in the application itself.
The benefits for you:
Engineering with one tool only
Intuitive configuration of power distribution
Access to measured and diagnostic data
More information:
www.siemens.com/lowvoltage/tia-portal

Siemens LV 14 2017

2/5

 Siemens AG 2016

Measuring Devices
7KM PAC Measuring Devices
7KM PAC3200 measuring devices

Selection and ordering data

Version

DT Article No.
www.siemens.com/
product?Article No.

PU
(UNIT,
SET, M)

PS*/
P. unit

PG

Weight
per PU
approx.
kg

7KM PAC3200 measuring device

Screw connection

Control panel instrument, 96 x 96 mm

Screw connections for connecting current and
voltage

7KM2112-0BA00-3AA0

1 unit

1DD

0.450

1 unit

1DD

0.459

1 unit

1DD

0.470

AC/DC wide-voltage power supply unit

UAUX:
95 240 V AC 10 %, 50/60 Hz
110 340 V DC 10 %
NSG0_00230

Measuring inputs
Ue: max. 690/400 V 3 AC, 50/60 Hz
Ie: /1 A or /5 A

7KM2112-0BA00-3AA0
7KM PAC3200 measuring device

Screw connection

Control panel instrument, 96 x 96 mm

Screw connections for connecting current and
voltage

7KM2111-1BA00-3AA0

DC power supply unit with extra-low voltage

UAUX: 22 65 V DC 10 %

NSG0_00230

Measuring inputs
Ue: max. 500/289 V 3 AC, 50/60 Hz
Ie: /1 A or /5 A

7KM2111-1BA00-3AA0
7KM PAC3200 measuring device

Ring cable lug

connection

Control panel instrument, 96 x 96 mm

Ring cable lug terminals for current and voltage
connection

7KM2112-0BA00-2AA0

AC/DC wide-voltage power supply unit

UAUX:
95 240 V AC 10 %, 50/60 Hz
110 340 V DC 10 %
NSG0_00228

Measuring inputs
Ue: max. 690/400 V 3 AC, 50/60 Hz
Ie: /1 A or /5 A

7KM2112-0BA00-2AA0

More information
For current transformers, see page 2/29 or
Catalog LV 10, chapter "Switch Disconnectors"
For other accessories, see page 2/28
powerconfig is available free of charge at
http://support.automation.siemens.com/WW/view/en/63452759
For more information about powerconfig, see chapter "Software"

2/6

Siemens LV 14 2017

* You can order this quantity or a multiple thereof.

 Siemens AG 2016

Measuring Devices
7KM PAC Measuring Devices
7KM PAC4200 measuring devices

Overview

Benefits
Simple mounting and commissioning
High IP65 degree of protection (front side, when installed)
permits usage in extremely dusty and wet environments
Intuitive operation using 4 function buttons and multilingual
plain text displays
Easy adaptation to different systems using integrated and
optional
- Digital inputs and outputs
- Communication interfaces
Worldwide use
- At least 8 languages
- International approvals
- Developed and tested to European and international
standards
Low mounting depth

The 7KM PAC measuring devices are used to measure and

display all relevant system parameters in low-voltage power
distribution. They can be used for both single-phase and multiphase measurements in 3 and 4-conductor power supply
systems (TN, TT, IT).
They record energy values for main distribution boards, electrical branches or individual loads precisely and reliably, and
also supply key measured values for assessment of the state of
the plant and the quality of the power supply.
The 7KM PAC4200 measuring device is fitted with an integrated
Modbus TCP interface via Ethernet, no expansion module is
required.
Power distribution in the TIA Portal
The devices fit seamlessly into V14 or higher of TIA Portal, thus
enabling parameter assignment, commissioning and automation of power distribution in the application itself.
The benefits for you:
Engineering with one tool only
Intuitive configuration of power distribution
Access to measured and diagnostic data
More information:
www.siemens.com/lowvoltage/tia-portal

Additional performance characteristics of the 7KM PAC4200:

Precise energy measurement
Versatile system integration
- Integrated Ethernet interface
- Optional communication modules available
- Multifunctional digital inputs and outputs
- Limit monitoring
Can be directly connected to power supply networks up to
690 V AC (UL-L), CATIII without voltage transformer
(with the exception of devices with power supply units with
extra-low voltage)
User-friendly configuration software powerconfig; see chapter
"Software"
Monitoring the plant status and the power supply quality
- Basic information for evaluating the power supply quality
- Logging of plant history in the form of operation, control and
system-related events
Recording of the power range through power averaging
(load profile)
Daily energy meters for apparent, active and reactive energy
across 365 days for cut-off date assessment
Detection of gas, water, compressed air or other energy
sources via pulse counter to the digital inputs
Can be expanded using modules to up to 10 digital inputs and
6 digital outputs
Counters for apparent, active and reactive energy for the
precise detection of the power consumption of a partial
process or manufacturing process
10/100 Mbit/s Ethernet interface with gateway function for
easy connection of devices with serial RS 485 interface via
expansion module 7KM PAC RS 485 to an Ethernet network
Comprehensive user-friendly indicators, such as user-defined
displays, bar and status indicators, phase diagram and list
and histogram graphics
Satisfies the accuracy requirements of class 0.1 S high-precision meters used by power supply companies according to
IEC 62053-22, which are normally reserved for exacting
industrial applications

Siemens LV 14 2017

2/7

 Siemens AG 2016

Measuring Devices
7KM PAC Measuring Devices
7KM PAC4200 measuring devices

Selection and ordering data

Version

DT Article No.
www.siemens.com/
product?Article No.

PU
(UNIT,
SET, M)

PS*/
P. unit

PG

Weight
per PU
approx.
kg

7KM PAC4200 measuring device

Screw connection

Control panel instrument, 96 x 96 mm

Screw connections for connecting current and
voltage

7KM4212-0BA00-3AA0

1 unit

1DD

0.546

1 unit

1DD

0.537

1 unit

1DD

0.544

NSG0_00230

AC/DC wide-voltage power supply unit

UAUX:
95 240 V AC 10 %, 50/60 Hz
110 340 V DC 10 %
Measuring inputs
Ue: max. 690/400 V 3 AC, 50/60 Hz
Ie: /1 A or /5 A

7KM4212-0BA00-3AA0
7KM PAC4200 measuring device

Screw connection

Control panel instrument, 96 x 96 mm

Screw connections for connecting current and
voltage

7KM4211-1BA00-3AA0

NSG0_00230

DC power supply unit with extra-low voltage

UAUX:
22 65 V DC 10 %
Measuring inputs
Ue: max. 500/289 V 3 AC, 50/60 Hz
Ie: /1 A or /5 A

7KM4211-1BA00-3AA0
7KM PAC4200 measuring device

Ring cable lug

connection

Control panel instrument, 96 x 96 mm

Ring cable lug terminals for current and voltage
connection

7KM4212-0BA00-2AA0

NSG0_00228

AC/DC wide-voltage power supply unit

UAUX:
95 240 V AC 10 %, 50/60 Hz
110 340 V DC 10 %
Measuring inputs
Ue: max. 690/400 V 3 AC, 50/60 Hz
Ie: /1 A or /5 A

7KM4212-0BA00-2AA0

More information
For current transformers, see page 2/29 or
Catalog LV 10, chapter "Switch Disconnectors"
For other accessories, see page 2/28
powerconfig is available free of charge at
http://support.automation.siemens.com/WW/view/en/63452759
For more information about powerconfig, see chapter "Software"

2/8

Siemens LV 14 2017

* You can order this quantity or a multiple thereof.

 Siemens AG 2016

Measuring Devices
7KM PAC Measuring Devices
7KM PAC5100 measuring devices

Overview

Benefits

7KM PAC5100 measuring device

The 7KM PAC measuring devices are used to measure and

display all relevant system parameters in low-voltage power
distribution. They can be used for both single-phase and multiphase measurements in 3 and 4-conductor power supply
systems (TN, TT, IT). They record energy values for main distribution boards, electrical branches or individual loads precisely
and reliably, and also supply key measured values for assessment of the state of the plant and the quality of the power supply.
The 7KM PAC5100 measuring device has an integrated
Modbus TCP interface via Ethernet and a web server for
parameterization, visualization and data management.

Simple mounting and commissioning

Intuitive operation via 4 function keys
integrated web server for parameterization, display and
evaluation
4 parameterizable LEDs
Worldwide use
- International approvals
- Developed and tested to European and international
standards
Low mounting depth
Precise energy measurement
Versatile system integration
- Integrated Ethernet interface
- Multifunctional digital outputs
- Limit monitoring
Can be directly connected to power supply networks up to
690 V AC (UL-L), CATIII without voltage transformer
Electrically isolated voltage inputs
Monitoring the plant status and the power supply quality
- Basic information for evaluating the power supply quality
- Logging of plant history in the form of operation, control and
system-related events
Energy counters for apparent energy, active energy, reactive
energy, as well as import, supply, inductive and capacitive
Comprehensive user-friendly indicators, such as user-defined
displays, bar and status indicators
Measurement up to the 40th individual harmonic of current
and voltage

Selection and ordering data

Version

DT Article No.
www.siemens.com/
product?Article No.

PU
(UNIT,
SET, M)

PS*/
P. unit

PG

Weight
per PU
approx.
kg

7KM PAC5100 measuring device

Screw connection

Control panel instrument, 96 x 96 mm

Screw connections for connecting current and
voltage

7KM5212-6BA00-1EA2

1 unit

1DD

0.807

1 unit

1DD

0.753

AC/DC wide-voltage power supply unit

UAUX:
110 230 V AC 10 %, 50/60 Hz
24 250 V DC 10 %
7KM5212-6BA00-1EA2

Measuring inputs
Ue: max. 690/400 V 3 AC, 50/60 Hz
Ie: /1 A or /5 A
7KM PAC5100 measuring device

Screw connection

Standard rail instrument without display

Screw connections for connecting current and
voltage

7KM5212-6CA00-1EA8

AC/DC wide-voltage power supply unit

UAUX:
110 230 V AC 10 %, 50/60 Hz
24 250 V DC 10 %
7KM5212-6CA00-1EA8

Measuring inputs
Ue: max. 690/400 V 3 AC, 50/60 Hz
Ie: /1 A or /5 A

More information
For current transformers, see page 2/29 or
Catalog LV 10, chapter "Switch Disconnectors"

* You can order this quantity or a multiple thereof.

Siemens LV 14 2017

2/9

 Siemens AG 2016

Measuring Devices
7KM PAC Measuring Devices
7KM PAC5200 measuring devices

Overview

Benefits

7KM PAC5200 measuring device

The 7KM PAC measuring devices are used to measure and

display all relevant system parameters in low-voltage power
distribution. They can be used for both single-phase and multiphase measurements in 3 and 4-conductor power supply
systems (TN, TT, IT).

They record energy values for main distribution boards, electrical branches or individual loads precisely and reliably, and
supply key measured values for assessment of the state of the
plant and the quality of the power supply.

The 7KM PAC5200 power quality measuring device has an integrated Modbus TCP interface via Ethernet and a web server for
parameterization, visualization and data management.

2/10

Siemens LV 14 2017

Simple mounting and commissioning

Intuitive operation via 4 function keys
4 parameterizable LEDs
integrated web server for parameterization, display and
evaluation
Worldwide use
- International approvals
- Developed and tested to European and international
standards
Low mounting depth
Precise energy measurement
Versatile system integration
- Integrated Ethernet interface
- Multifunctional digital outputs
- Limit monitoring
Can be directly connected to power supply networks up to
690 V AC (UL-L), CATIII without voltage transformer
Electrically isolated voltage inputs
Monitoring the plant status and the power supply quality:
- Basic information for evaluating the power supply quality
- Logging of plant history in the form of operation, control and
system-related events
- Flicker acc. to IEC 61000-4-15
Energy counters for apparent energy, active energy, reactive
energy, as well as import, supply, inductive and capacitive
Comprehensive user-friendly indicators, such as user-defined
displays, bar and status indicators
Measurement up to the 40th individual harmonic of current
and voltage
Integrated 2 GB SD card for recorder functions
Flexible recorder:
- Measured value recorder
- Trend recorder
- Event recorder
- Fault recorder
Integrated PQ recording and reporting in accordance with
EN 50160
Data export:
- COMTRADE
- PQDif
Classification of events
ITIC /CBEMA evaluation in the device

 Siemens AG 2016

Measuring Devices
7KM PAC Measuring Devices
7KM PAC5200 measuring devices

Selection and ordering data

Version

DT Article No.
www.siemens.com/
product?Article No.

PU
(UNIT,
SET, M)

PS*/
P. unit

PG

Weight
per PU
approx.
kg

7KM PAC5200 measuring device

Screw connection

Control panel instrument, 96 x 96 mm

Screw connections for connecting current and
voltage

7KM5412-6BA00-1EA2

1 unit

1DD

0.809

1 unit

1DD

0.754

AC/DC wide-voltage power supply unit

UAUX:
110 230 V AC 10 %, 50/60 Hz
24 250 V DC 10 %
7KM5412-6BA00-1EA2

Measuring inputs
Ue: max. 690/400 V 3 AC, 50/60 Hz
Ie: /1 A or /5 A
7KM PAC5200 measuring device

Screw connection

Standard rail instrument without display

Screw connections for connecting current and
voltage

7KM5412-6CA00-1EA8

AC/DC wide-voltage power supply unit

UAUX:
110 230 V AC 10 %, 50/60 Hz
24 250 V DC 10 %
7KM5412-6CA00-1EA8

Measuring inputs
Ue: max. 690/400 V 3 AC, 50/60 Hz
Ie: /1 A or /5 A

More information
For current transformers, see page 2/29 or
Catalog LV 10, chapter "Switch Disconnectors"

* You can order this quantity or a multiple thereof.

Siemens LV 14 2017

2/11

 Siemens AG 2016

Measuring Devices
7KM PAC Measuring Devices
Accessories for 7KM PAC

Selection and ordering data

for 7KM PAC3100/3200/4200

Version

DT Article No.
www.siemens.com/
product?Article No.

PU
(UNIT,
SET, M)

PS*/
P. unit

PG

Weight
per PU
approx.

7KM9900-0XA00-0AA0

1 unit

1DD

0.397

7KM9900-0YA00-0AA0

1 unit

1DD

0.146

7KM9900-0GA00-0AA0

1 unit

1DD

0.148

7KM9900-0SA00-0AA0

1 unit

1DD

0.118

kg
7KM PAC TMP2 standard mounting rail
adapter
Two-tier adapter for mounting a measuring
device on a standard mounting rail
Front display
7KM9900-0XA00-0AA0

For manual intervention

7KM PAC TMP mounting plate

Adapter for mounting a measuring device on
standard mounting rail
Display faces backwards towards standard
mounting rail
7KM9900-0YA00-0AA0

Readout and evaluation of measurements

solely via mains operation

Compact holder
Device holder for 7KM PAC3100/3200/4200:
10 holders for 5 PAC devices
For seamless side-by-side mounting of the
devices (without spaces)
7KM9900-0GA00-0AA0
7KM PAC spare parts
Spare parts comprising:
Device holders for panel mounting (2X)
Screw terminal for connection of voltage inputs
7KM9900-0SA00-0AA0

Screw terminal for connection of current inputs

Terminal block inputs/outputs
for 7KM PAC3100/4200
Terminal block inputs/outputs
for 7KM PAC3200
Terminal block RS 485
for 7KM PAC3100

More information
Current transformers

Software components

For current transformers, see page 2/29 or

Catalog LV 10, chapter "Switch Disconnectors"

For more information about the software components

see chapter "Software"
and on the Internet at
www.siemens.com/lowvoltage/powermonitoring
More information
More information is available on the Internet at:
www.siemens.com/lowvoltage/powermonitoring

2/12

Siemens LV 14 2017

* You can order this quantity or a multiple thereof.

 Siemens AG 2016

Measuring Devices
7KM PAC Measuring Devices
7KM PAC expansion modules

Overview
Versions
The following expansion modules are available (shown from left

to right in the figure on the left):

7KM PAC Switched Ethernet PROFINET expansion module
7KM PAC PROFIBUS DP expansion module
7KM PAC RS 485 expansion module
7KM PAC 4DI/2DO expansion module
Connection for 3VA molded case circuit breakers
The following expansion modules can be mounted on the front
of the COM800/COM100 data concentrators of the 3VA molded
case circuit breaker:
7KM PAC Switched Ethernet PROFINET and
7KM PAC PROFIBUS DP
Expansion modules are used as communication interfaces and
for expanding the digital inputs/outputs for 7KM PAC measuring
devices.
The expansion modules are plugged in at the back of the
measuring device. The device identifies the module automatically and presents the relevant parameters for this module for
selection in the parameterization menu.

For further details, see Catalog LV 10, chapter "Molded Case

Circuit Breakers" or in the manual at
http://support.automation.siemens.com/WW/view/en/90318775
More information
For more information about the software components
see chapter "Software" and on the Internet at
www.siemens.com/lowvoltage/powermonitoring

Version

Use in

PAC3200

PAC4200

PAC5100

PAC5200

COM800/
COM100

3VA

PAC3100

7KM PAC

--

--

--

7KM PAC expansion modules

7KM PAC Switched Ethernet PROFINET expansion module
The 7KM PAC Switched Ethernet PROFINET expansion module is a plug-in communication
module for 7KM PAC3200 and 7KM PAC4200 measuring devices and 3VA molded case
circuit breakers.
It provides the following features:
Standardized PROFIenergy interface to the measured quantities
The measured quantities can be individually selected using a GSDML file. This permits
use of cost-effective S7 CPUs
Easy parameter assignment using the device display and STEP 7
Integrated Ethernet switching allows networking with short cables without additional
switches
Direct integration in production machine networks using IRT (IRT = Isochronous-RealTime)
Full support of PROFINET IO (DHC, DNS, SNMP, SNTP)
Device replacement without PG in the PROFINET assembly using LLDP
Deterministic reversing time through ring redundancy (MRP)
Modbus TCP communication
Communication with powermanager or powerconfig
2 x Ethernet (RJ45) sockets
Transmission rates 10 and 100 Mbit/s
Protocols PROFINET IO, PROFIenergy and Modbus TCP
No external auxiliary power necessary
Additional display via the device display and via LEDs on the module
All measured variables from 7KM PAC3200 and 7KM PAC4200 can be individually
selected and cyclically transmitted by means of the GSDML file. This enables optimum use
of the process image of the PROFINET controller, e.g. CPU 315-2 PN/DP of SIMATIC S7.
The measured quantities can be read out in acyclic mode using PROFIenergy, a PNO
protocol profile. Thanks to PROFIenergy, it is possible to assemble a power monitoring
system with devices from various manufacturers using PROFINET.

Siemens LV 14 2017

2/13

 Siemens AG 2016

Measuring Devices
7KM PAC Measuring Devices
7KM PAC expansion modules
Version

Use in

PAC3200

PAC4200

PAC5100

PAC5200

COM800/
COM100

7KM PAC PROFIBUS DP expansion module

3VA

PAC3100

7KM PAC

--

--

--

--

--

--

--

--

--

--

--

--

The 7KM PAC PROFIBUS DP expansion module is a plug-in communication module for
7KM PAC3200 and 7KM PAC4200 measuring devices and 3VA molded case circuit
breakers.
The 7KM PAC PROFIBUS DP expansion module has the following features:
Plug-in communication module for measuring devices for connection to PROFIBUS DPV1
For 7KM PAC3200 and 7KM PAC4200
Parameterizable via device front or using parameterization software
Data can be transferred both cyclically and acyclically via PROFIBUS DPV1
Easy engineering thanks to integration in SIMATIC STEP 7 and/or simple integration via
GSD file for other programming systems
Optimum use of process image of a control system for selection of individual measured
quantities for cyclical transfer
Supports all baud rates from 9.6 kbit/s up to 12 Mbit/s
Connection through 9-pole Sub-D connector according to IEC 61158
No external auxiliary power necessary
Additional display via the device display and via LEDs on the module
7KM PAC RS 485 expansion module
The 7KM PAC RS 485 expansion module has the following features:
Plug-in 7KM PAC RS 485 communication module for 7KM PAC3200 and 7KM PAC4200
measuring devices and 3VA molded case circuit breakers
Parameterizable via device front or using parameterization software
Support for the Modbus RTU protocol
Plug and play
Supports transmission rates of 4.8/9.6/19.2 and 38.4 kbit/s
Connection by means of 6-pole screw terminals
No external auxiliary power necessary
Status indication by LED on the module
The 7KM PAC RS 485 expansion module is required for the gateway function of the
7KM PAC4200 for communication with simple devices with RS 485 interface, such as the
7KM PAC3100, via Ethernet (Modbus TCP).
7KM PAC 4DI/2DO expansion module
The 7KM PAC 4DI/2DO expansion module is used to expand the
7KM PAC4200 measuring device to up to 10 digital inputs and 6 digital outputs and offers
the following features:
Up to two 7KM PAC 4DI/2DO modules can be plugged onto a 7KM PAC4200.
The 7KM PAC 4DI/2DO expansion modules mean that the internal digital inputs and
outputs can be expanded by up to 8 inputs and 4 outputs.
The 7KM PAC 4DI/2DO expansion modules can be configured locally at the front of the
device or via the powerconfig parameterization software
The digital inputs can be used without the need for an external power supply as they are
self-powered. This is particularly useful for the integration of non-electric measuring
devices, such as water or compressed-air counters
All functions of the integrated multifunctional inputs/outputs on the 7KM PAC4200 are also
available in the 7KM PAC 4DI/2DO expansion module
Inputs and outputs can be used as an S0 interface conforming to IEC 62053-31
The connection is made via a 9-pole screw terminal
No external auxiliary power supply is required

2/14

Siemens LV 14 2017

 Siemens AG 2016

Measuring Devices
7KM PAC Measuring Devices
7KM PAC expansion modules

Selection and ordering data

Version

DT Article No.
www.siemens.com/
product?Article No.

PU
(UNIT,
SET, M)

PS*/
P. unit

PG

Weight
per PU
approx.
kg

7KM PAC Switched Ethernet PROFINET

expansion module
Expansion module for 7KM PAC3200 and
7KM PAC4200 (PROFIenergy) and
COM100/800 (3VA) breaker data server

7KM9300-0AE01-0AA0

1 unit

1DD

0.070

7KM9300-0AB01-0AA0

1 unit

1DD

0.079

7KM9300-0AM00-0AA0

1 unit

1DD

0.074

7KM9200-0AB00-0AA0

1 unit

1DD

0.073

7KM9300-0AE01-0AA0
7KM PAC PROFIBUS DP expansion module
Expansion module for 7KM PAC3200 and
7KM PAC4200 (PROFIBUS DPV1) and
COM100/800 (3VA) breaker data server

7KM9300-0AB01-0AA0
7KM PAC RS 485 expansion module
Expansion module for 7KM PAC3200 and
7KM PAC4200 (Modbus RTU) and
COM100/800 (3VA) breaker data server

7KM9300-0AM00-0AA0
7KM PAC 4DI/2DO expansion module
Expansion module for 7KM PAC4200

7KM9200-0AB00-0AA0

* You can order this quantity or a multiple thereof.

Siemens LV 14 2017

2/15

 Siemens AG 2016

Measuring Devices
7KT PAC Measuring Devices
Introduction

Overview
Application

2/17

Measurement of individual feeders thus

direct comparison of consumers

Standards

Used in

Industry

Page

Residential
buildings

Devices

Non-residential
buildings

7KT PAC measuring devices

7KT PAC1200 multichannel
current measuring system

Detection of current peaks thus avoidance

of high energy costs

7KT12

Web server and app representation thus

plug-and-play visualization of measured
values and consumption values

7KT PAC1500 three-phase

measuring devices

2/22

Measurement of consumption data in three- EN 50470-1,

phase systems of plant sections, offices or EN 50470-3
holiday apartments.
EN 62052-23,
EN 62053-31

2/24

For measurement of consumption data in

EN 50740-1,
single-phase systems, e.g. in industrial
EN 50470-3,
plants, offices and apartments in apartment EN 62053-31
blocks.

2/25

Communication interfaces with IrDA infrared EN 13321-1,

interface for 7KT PAC1500 measuring
EN 13757
devices. Modules are available for the
ISO/IEC 14543-3
following bus systems:
EN 50090
M-Bus

--

7KT154

7KT PAC1500 single-phase

measuring devices
7KT153

7KT PAC expansion modules

7KT19

Modbus RTU
RS 485 (7KT1391 LAN coupler connection)
KNX/EIB

7KT LAN couplers

2/26

Web server with 2 GB internal storage, for

up to 30 7KT15.... measuring devices.
Global view and Excel export of current
consumption data via LAN or Internet using
a web browser such as Firefox.

2/16

Siemens LV 14 2017

IEEE 802

 Siemens AG 2016

Measuring Devices
7KT PAC Measuring Devices
7KT PAC1200 multichannel current measuring system

Overview
Representation of the current values
Under the navigation item "Current values" you can see how high
the consumption at a particular moment in time is. The value
behind "Current" indicates this consumption. "Min/Max" indicates
the minimum and maximum consumption. The kW values
consumed at a certain time are shown in a curve diagram. Here
also, either the overall consumption or the consumption of an
individual sensor can be displayed. It is also possible to switch
between various modes in this view.
History
Current reading: for individual sensors
- Current
- Voltage
- Power factor of the individual phases
Counter reading

7KT PAC1200 multichannel current measuring system

Installation in an ALPHA power distribution board,

for example

The 7KT PAC1200 multichannel current measuring system is

used for the transparent representation of energy consumption.
The current values themselves are measured by means of
sensors that are fitted above the miniature circuit breakers. The
simple cost center allocation enables maximum transparency
over the entire application.
Scalability
The 7KT PAC1200 multichannel current measuring system monitors and displays the energy consumption of up to 96 outgoing
feeders. A maximum of eight sensor bars can be configured.
Up to eight different, selectable consumption sources can be
compared with each other. The system can be scaled to individual needs and application scenarios. The individual sensors
can be named individually and compared with each other. The
system can be configured flexibly as the number of sensor bars
can be varied.
Consumption statistics
The statistics shows the overall consumption of selected
sensors. The consumption can be shown both in euros and in
kWh. The results can be displayed in the form of a pie chart or a
bar chart, depending on selection. The periods that can be
selected are as follows:
Days
Weeks
Months
Year
Both the overall consumption and the individual consumption of
a sensor can be displayed.
It is also possible to generate a history so that any deviations can
be investigated. To do this, select a date using the button below
the chart.

7KT PAC1200 multichannel current measuring system installed

Benefits
Measurement of individual feeders thus direct comparison of
consumers
Detection of current peaks thus avoidance of high energy
costs
Web server and app representation thus plug-and-play
visualization of measured values and consumption values

Scalability thus number of measuring points can be adjusted

to size of the power distribution system
1 GB internal memory thus long-time data recording over
one year possible

Siemens LV 14 2017

2/17

 Siemens AG 2016

Measuring Devices
7KT PAC Measuring Devices
7KT PAC1200 multichannel current measuring system

Application

Use cases

Fields of application
Carpenters' and joiners' workshops, locksmiths' shops
Large bakeries, breweries, slaughterhouses
Municipal utilities
Banks, etc.

Energy measurement on
Strip lighting
Production machines
Motors
Application example

Modbus TCP
TCP/IP
powermanager

7KT PAC1200
Cooling
68.72kWh
13.83 EUR

Energy consumption per day:

334.9 kWh

7KT PAC1200
Boiling kettle
68.72kWh
13.83 EUR

7KT PAC1200
Light_01
68.72kWh
13.83 EUR

7KT PAC1200
Light_02
68.72kWh
13.83 EUR

7KT PAC1200
Botteling
68.72kWh
13.83 EUR

Energy costs per day:

66.99 EUR
I201_19506

Result: For example, display of overall energy consumption (from application example above)

2/18

Siemens LV 14 2017

 Siemens AG 2016

Measuring Devices
7KT PAC Measuring Devices
7KT PAC1200 multichannel current measuring system

Technical specifications
7KT PAC 1200 multichannel

7KT1222

7KT1223

7KT1260

7KT123./4.

7KT125.

current measuring system

1 x 18 bundle

1 x 24 bundle

Data manager

Sensor bar

Sensor

Product designation

Starter kit

Starter kit

Data manager

Sensor bar

Sensor

Version

2x9 with system, 40 A

2x12 with system, 40 A

3/6/9/12-bar

40 A / 63 A

--

--

Direct / transformer 5 A --

--

--

--

63

--

40 / 63

--

--

Measuring input
Connection type
Current Ie

Total accuracy +/- 2% (of full-scale value / class 2)

Measuring accuracy
Measurable line frequency

Hz

50 +/- 5%

50 +/- 5%

50 +/- 5%

Communication
Sensor bar connection
to Data manager

RS 485

--

Data manager connection

to web browser

Ethernet via RJ 45, Modbus TCP protocol (10 / 100 Mbit/s)

--

--

85

3-bar: 54.5
6-bar: 105.5
9-bar: 159.5
12-bar: 212.4

32

70

21

17.7

--

--

32.7

14.8

13

Dimensions and weights

Height

mm

Width

mm

Data manager width

MW1) 4

Depth

mm

1)

1 MW = 1 modular width = 18 mm

Siemens LV 14 2017

2/19

 Siemens AG 2016

Measuring Devices
7KT PAC Measuring Devices
7KT PAC1200 multichannel current measuring system

Selection and ordering data

DT Article No.
www.siemens.com/
product?Article No.

Price
PU
per PU (UNIT,
SET,
M)

PS*/
P. unit

PG

Weight
per PU
approx.
kg

7KT1222

1 unit 1BK

1.994

7KT1223

1 unit 1BK

2.222

7KT1260

1 unit 1BK

0.350

3-Sensor bar

7KT1233

1 unit 1BK

0.011

6-Sensor bar

7KT1236

1 unit 1BK

0.016

9-Sensor bar

7KT1238

1 unit 1BK

0.024

12-Sensor bar

7KT1242

1 unit 1BK

0.032

Sensor 40 A

7KT1254

1 3 units 1BK

0.035

Sensor 63 A

7KT1255

1 3 units 1BK

0.035

7KT PAC1200 multichannel current measuring system

Multichannel current measuring system for locating high
consumption values and cost center allocation
1 x 18 bundle, containing:
2 x 9-Sensor bar 7KT1238
1 x Data manager 7KT1260
18 x Sensors 40 A, 7KT1254
7KT PAC1200 multichannel current measuring system
Multichannel current measuring system for locating high
consumption values and cost center allocation
1 x 24 bundle, containing:
2 x 12-Sensor bar 7KT1242
1 x Data manager 7KT1260
24 x Sensors 40 A, 7KT1254
7KT PAC1200 Data manager
Fully integrated smart meter, containing
3-phase active power and reactive power energy
measurement
Measurement of imported energy as balancing counter
Direct connection up to 63 A
Optional use with external measuring transformer for
extending the measuring range (e.g. 100 ... 600 A)
Standard rail mounting (4 MW)
Operation / configuration: Web interface
Support of up to 96 sensors for single-phase
measurement
7KT PAC1200 Sensor bars

Sensors

2/20

Siemens LV 14 2017

* You can order this quantity or a multiple thereof.

 Siemens AG 2016

Measuring Devices
7KT PAC Measuring Devices
7KT PAC1200 multichannel current measuring system

More information

Procurement costs: The more measuring points (sensors) the lower the costs

Price

Price per measuring point

7KT PAC1200 multichannel current measuring system

Price per measuring point

Starterkit 18
Starterkit 24

10

20

30

40

50

60

70

80

90

Number of measuring points

I201_19505

Internet
You can find more information on the Internet at
www.siemens.com/powermonitoring
Apple iOS

7KT PAC1200 App

iOS

Android

7KT PAC1200 App

ANDROID

Siemens LV 14 2017

2/21

 Siemens AG 2016

Measuring Devices
7KT PAC Measuring Devices
7KT PAC1500 three-phase measuring devices

Overview
The measuring devices (power meters) are used to record the
amount of electrical energy and power exported and imported.
Siemens compact measuring devices are designed as modular
devices for alternating current and can be mounted on standard
mounting rails. They comply with the metering equipment standard EN 50470 (Part 1 and 3) and come with an LCD display.
The three-phase measuring devices for direct connection are
available up to 125 A and in versions with transformer
connections (/5 A to 10000/5 A).
The measuring devices store active and reactive energy and all
comply with accuracy class 1 (for active energy).

All measuring devices have a pulse output (S0) and are

designed for 2-tariff measurements. The MID versions comply
with the new Measuring Instruments Directive 2004/22/EC.
The measuring devices also have an integrated optical interface
(IrDA) for connecting communication modules, which enables
their integration in a range of other systems, such as power
management systems.
7KT PAC1500 measuring devices, three-phase, for direct connection
up to 80 A / 125 A

Technical specifications
7KT PAC1500 three-phase measuring device
Standards
Connection
Direct connection
Transformer current connection
General data
Enclosure
Mounting
Mounting height
Function
Connection
Storage of setting and counter reading
Tariffs
Supply (through measuring terminals)
Rated control supply voltage Un
Voltage range
Rated frequency fn
Measuring accuracy (at 23 1 C)
Active energy and active power
Reactive energy and reactive power
Measuring input
Connection type
Terminal capacity
Voltage Un
Operating range voltage

Current Iref
Current In
Current Imin
Current operating range (Ist Imax)

Transformer current

Acc. to DIN 43880

Acc. to EN 60715

Single-phase or three-phase
Via (EEPROM)
For active and reactive energy

80 A
--

125 A
--

4
35 mm
70

No. of conductors

4
Yes
T1/T2

2 ... 4
Yes
T1/T2

2 ... 4
Yes
T1/T2

V AC
V
Hz

230
110... 276
50

Direct
1.5 (35)
1.5 (35)

Direct
5 (50)
5 (50)

5
-0.25
0.015 ... 80
----

5
-0.25
0.020 ... 125
----

15

20

500
--

500
--

MW (1 MW = 18 mm)

Based on nominal value

Acc. to EN 50470-3
Acc. to EN 62053-23

Rigid, min. (max.)

Flexible min. (max.)

Class B
Class 2

mA

Transformer TA-TC .../5 A

1.5 (6)
1.5 (6)
400
230
190 ... 480
110 ... 276
-5
0.05
-0.003 ... 6
5 ... 10000
5
Sinusoidal
3

Pulses/kWh
Pulses/kWh

Yes
-100 - 10 - 1

mm2
mm2

Phase/phase
Phase/N
Phase/phase
Phase/N

V
V
V
V
A
A
A
Direct connection
A
Transformer connection
A
Primary current of the transformer A
Smallest input step
A

IR interface
At the side for connecting communication modules

Siemens LV 14 2017

-.../5 A

mm

Input ripple form

Operational starting current Ist
S0 interface
Acc. to EN 62053-31
Pulse outputs for absorbed active and reactive energy T1 + T2
Pulse count
For input current Imax
Automatic for transformers

2/22

7KT1540
7KT1543
7KT1546
7KT1542
7KT1545
7KT1548
EN 50470-1, EN 50470-3, EN 62053-23, EN 62053-31

M-Bus/Modbus RTU/RS 485/KNX

 Siemens AG 2016

Measuring Devices
7KT PAC Measuring Devices
7KT PAC1500 three-phase measuring devices

Selection and ordering data

Un

Imax

Mount- DT Article No.

www.siemens.com/
ing
product?Article No.
width

Price
PU
per PU (UNIT,
SET,
M)

PS*/
P. unit

PG

Weight
per PU
approx.

V AC A AC

MW

kg

For transformer connection,

double tariff

230

Transformer /5

7KT1540

1 unit 1DD

0.257

For transformer connection,

double tariff, MID

230

Transformer /5

7KT1542

1 unit 1DD

0.255

For direct connection, double tariff

230

80

7KT1543

1 unit 1DD

0.409

For direct connection, double tariff, MID 230

80

7KT1545

1 unit 1DD

0.408

7KT PAC1500 three-phase measuring

device
Digital measuring device

For direct connection, double tariff

230

125

7KT1546

1 unit 1DD

0.705

For direct connection, double tariff, MID 230

125

7KT1548

1 unit 1DD

0.710

* You can order this quantity or a multiple thereof.

Siemens LV 14 2017

2/23

 Siemens AG 2016

Measuring Devices
7KT PAC Measuring Devices
7KT PAC1500 single-phase measuring devices

Overview
The 7KT PAC1500 single-phase measuring devices (power
meters) are used to record the amount of electrical energy and
power exported and imported. They comply with the metering
equipment standard EN 50470 (Part 1 and 3) and come with an
LCD display.
The 7KT PAC1500 single-phase measuring devices for direct
connection are available up to 80 A. They store active and
reactive energy, and all comply with accuracy class 1 (for active
energy).
All measuring devices have a pulse output (S0) and are
designed for 1-tariff or 2-tariff measurements, depending on the
version.
The MID versions comply with the new Measuring Instruments
Directive 2004/22/EC. The measuring devices (with the exception of 7KT1530) also have an integrated optical interface (IrDA)
for connecting communication modules.

Technical specifications
7KT PAC1500 single-phase measuring device
Direct connection up to 80 A

7KT1530

7KT1531
7KT1533

Standards

EN 50470-1, EN 50470-3, EN 62053-23, EN 62053-31

General data
Enclosure

Acc. to DIN 43880

Mounting

Acc. to EN 60715

MW

2
35 mm

Mounting height

mm

70

Conductors

Function
Operating mode

Single-phase loads

Storage of setting and counter reading

Via (EEPROM)

Yes

Tariff

For active energy

For reactive energy

T1
T1

T1 + T2
T1 + T2

Supply (through measuring terminals)

Rated control supply voltage Un

V AC

230

Voltage range

110 ... 276

Rated frequency fn

Hz

50

Measuring accuracy (at 23 1 C)

Based on nominal value

Active energy and active power

Acc. to EN 50470-3

Class B

Reactive energy and reactive power

Acc. to EN 62053-23

Class 2

Measuring input
Connection type

Phase/N

Terminal capacity

Rigid, min. (max.)

Flexible min. (max.)

Direct

Operating range voltage

Phase/N

mm2
mm2

1.5 (35)
1.5 (35)

1.5 (35)
1.5 (35)

V AC

110... 276

Current Iref

Current Imin
Current operating range (Ist ... Imax)

0.25

0.015 ... 80

Direct connection

Sinusoidal

Current waveform
Operational starting current Ist

mA

15

Acc. to EN 62053-31

S0 interface

Pulse outputs for consumed active and reactive energy

Yes

Pulse count

Pulses/kWh

1000

IR interface
At the side for connecting communication modules (M-Bus/Modbus RTU/RS 485/KNX)

--

Yes

Selection and ordering data

Un

Imax

Mount- DT Article No.

www.siemens.com/
ing
product?Article No.
width

V AC

A AC

MW

Price
per PU

PU
(UNIT,
SET, M)

PS*/
P. unit

PG

Weight
per PU
approx.
kg

7KT PAC1500 single-phase measuring

devices
Digital measuring device

2/24

For direct connection, single tariff

230

80

7KT1530

1 unit

1DD

0.206

For direct connection, double tariff

230

80

7KT1531

1 unit

1DD

0.207

For direct connection, double tariff, MID 230

80

7KT1533

1 unit

1DD

0.208

Siemens LV 14 2017

* You can order this quantity or a multiple thereof.

 Siemens AG 2016

Measuring Devices
7KT PAC Measuring Devices
7KT PAC expansion modules

Overview
The expansion modules are placed alongside the measuring
devices in the installation direction so that their IrDA interfaces
are exactly opposite each other.
7KT PAC M-Bus expansion module (7KT1908)
Power supply through bus cable
Baud rates: 300 to 9600 kbit/s
Status indication by LED on the module
Can be parameterized using M-Bus master software
7KT PAC Modbus RTU expansion module (7KT1907)
Power supply: 230 V AC
Baud rates: 4.8/9.6/19.2 and 38.4 kbit/s are supported.
Status indication by LED on the module
Configurable via RS 485 master software
Expansion modules for 7KT PAC1500 measuring devices, from left to right:
Expansion modules for M-Bus, Modbus RTU, RS 485, Instabus KNX

Expansion modules are used as communication interfaces for

7KT PAC1500 measuring devices. They have the following
features:
The expansion modules can be selected independently of the
measuring device. This means they can also be retrofitted in
already installed measuring devices.
Data transmission between the measuring devices and
expansion modules is executed via the IrDA infrared interface.

7KT PAC RS 485 expansion module (7KT1903)

Power supply: 230 V AC
Status indication by LED on the module
7KT PAC 7KNX expansion module (7KT1900)
Power supply through the KNX/EIB bus cable
Status indication by LED on the module

Selection and ordering data

Version

Mounting
width

DT Article No.
www.siemens.com/
product?Article No.

Price
per PU

PU
(UNIT,
SET, M)

PS*/
P. unit

PG

Weight
per PU
approx.
kg

MW
7KT PAC M-Bus expansion module

7KT1908

1 unit

1DD

0.055

7KT1907

1 unit

1DD

0.084

7KT1903

1 unit

1DD

0.085

7KT1900

1 unit

1DD

0.063

For connecting 7KT PAC1500 measuring devices to

M-Bus

7KT1908

7KT PAC Modbus RTU expansion module

For connecting 7KT PAC1500 measuring devices to
Modbus RTU

7KT1907

7KT PAC RS 485 expansion module

For connecting 7KT PAC1500 measuring devices
via RS 485 to 7KT1391 LAN couplers

7KT1903

7KT PAC KNX expansion module

For connecting 7KT PAC1500 measuring devices to
Instabus KNX

7KT1900

* You can order this quantity or a multiple thereof.

Siemens LV 14 2017

2/25

 Siemens AG 2016

Measuring Devices
7KT PAC Measuring Devices
7KT LAN couplers

Overview

Application

Suitable 7KT PAC measuring devices

The following measuring devices can be connected to the LAN
coupler:
Article No.
Energy measuring devices
7KT PAC1500 three-phase measuring device
For direct connection 80 A, double tariff

7KT1543

For direct connection 80 A, double tariff, MID

7KT1545

For transformer connection .../5 A, double tariff

7KT1540

For transformer connection .../5 A, double tariff, MID

7KT1542

For direct connection 125 A, double tariff

7KT1546

For direct connection 125 A, double tariff, MID

7KT1548

7KT PAC1500 single-phase measuring device

For direct connection 80 A, double tariff

7KT1531

For direct connection 80 A, double tariff, MID

7KT1533

Connecting several devices to a 7KT LAN coupler

7KT LAN couplers

A LAN coupler supports worldwide data retrieval from 7KT PAC

measuring devices, as long as there is a LAN link to the Internet.
Up to 30 devices can be linked to a LAN coupler via a web
browser, such as Firefox. In turn, the LAN coupler is connected
to a LAN.

LAN coupler
7KT1391

Device 1

Device 2

Device 30

I201_11596d

Data communication between the LAN coupler and the PC takes

place using the TCP/IP protocol.

Technical specifications
7KT LAN couplers
IEEE 802.3 AS, IEC 60950, EN 61000-6-2, EN 61000-6-3

Standards
General data
Enclosures

Acc. to DIN 43880

Mounting

Acc. to EN 60715

Mounting height

4 modules
Mounting on standard mounting rail (35 mm)
mm

70

Supply
Rated power dissipation Pv

VA

10

Rated control supply voltage Uc

V AC

230

Primary operating range

Uc

0.9 ... 1.10

Rated frequency

Hz

50

Frequency range

Hz

45 ... 65

Function
System start

Automatic upon switching on

LAN server identification

Transmission rate

Via the IP address of the PC

Limitation by LAN

Mbit/s

100

Operating system

Windows XP/Vista/7

Browser

IE 7,8; Mozilla Firefox 3.09 / 3.5.3 / 3.6; Opera 9.64 / 10 / 10.5;

Safari 3.2.2 /4.0.5; Google Chrome 3.0.195.27.

LAN interface
HW interface

Connection RJ 45

SW interface

TCP/IP

2/26

Siemens LV 14 2017

 Siemens AG 2016

Measuring Devices
7KT PAC Measuring Devices
7KT LAN couplers
7KT LAN couplers
Interface to measuring devices
HW interface

RS 485 terminals

Line

Version
Minimum cross-section
Maximum line capacitance
Impedance
Maximum overall cable length
Type of installation

Number 3 (+/-/shielded twisted pair)

mm2
pF/m
W
m

STP (shielded twisted pair)

2 0.2 or 2 x AWG 24
< 50
100
1200
Serial

Number 30

Measuring devices can be connected

directly
Environmental conditions
Temperatures

In operation
Storage and transport

C
C

-10 ... +55

-25 ... +70

Relative humidity

In operation

80

Vibrations

Sine amplitude at 50 Hz

mm

0.25

Safety class

Acc. to IEC 60950

III

Degree of protection

Installed device front side (terminals)

IP20

Selection and ordering data

Version

Uc

Mounting DT Article No.

www.siemens.com/
width
product?Article No.

V AC

MW

Price
PU
per PU (UNIT,
SET,
M)

PS*/
P. unit

PG

Weight
per PU
approx.
kg

LAN couplers
For connection of up to 30 devices via RS 485
230

* You can order this quantity or a multiple thereof.

7KT1391

1 unit

1DD

Siemens LV 14 2017

0.215

2/27

 Siemens AG 2016

Measuring Devices
Accessories
Introduction

Page

Application

Standards

Used in

Residential
buildings

Industry

Non-residential
buildings

Overview
Devices

4NC current transformers

2/29

Window-type current transformers/pin-wound

transformers, particularly suitable for long
measuring leads, low cable losses

EN 60044-1,
VDE 0414-44-1

--

7KT12 current transformers

2/32

Straight-through transformers for installation in

distribution boards and non-contact measuring of
primary currents.

IEC 60044-1,

EN 60044-1
(VDE 0414 T 44-1)

--

Accessories

Ideal for combination with switch disconnectors,

measuring devices and counters.

2/28

Siemens LV 14 2017

 Siemens AG 2016

Measuring Devices
Accessories
4NC current transformers

Overview

4NC53 current transformers

Technical specifications
4NC current transformers for measuring purposes
Standards
Window-type current transformers

Rated primary current Ipn

Rated secondary current Isn
1A
5A

Accuracy class
Class 1
Class 3
Rated power Pn

Maximum voltage for equipment Um

Overcurrent limiting factor FS

Rated short-time thermal current Ith

Rated impulse current Idyn

EN 60044-1, VDE 0414-44-1

The conductor to be measured (busbar or cable) is passed through the window opening and constitutes the
primary circuit of the window-type current transformer.
Pin-wound transformers: An economical solution especially for small primary currents of 5 ... 75 A are
window-type current transformers when the conductor to be measured is pin-wound several times.
Current transformers can be continuously loaded with 1.3 times the rated primary current (Ipn).
Particularly suitable for longer measuring leads. Cable losses of only 4 %
in contrast to 5 A current transformers.
5 A current transformers generate 25 times the power losses on measuring leads as compared with 1 A current
transformers. These stray losses result in higher power in the case of long cables. Only recommended for use
with short measuring leads.
Operation measurement, internal metering
Current error 1 % at 1 x Ipn and 1.2 x Ipn
Coarse measurement
Current error 3 % at 0.5 x Ipn and 1.2 x Ipn
The rated power of transformers is specified in VA. The actual load rating should be similar to the rated power;
a lower actual load rating (underburden) increases the overcurrent factor and measuring devices are not
sufficiently protected in case of a short-circuit, a higher actual load rating (overburden) has a negative effect on
the accuracy.
With a frequency of 60 Hz the rated power increases to 1.2 times. With 162/3 Hz the output power decreases to
1/ of the rated power.
3
This is the rms value of the maximum voltage between the conductors of a system. For this voltage the
insulation must be rated at normal operating conditions.
4NC5 current transformers are suitable for 720 V.
The overcurrent limiting factor is expressed using the characters FS and a factor, e.g. FS5 or FS10.
When a short-circuit current flows through the primary winding of a current transformer, the stress on the
measuring devices connected to the current transformer is the lower the smaller the overcurrent limiting factor
is.
The rated short-time thermal current Ith is the rms value of the primary current with a duration of one second,
whose heat effect the current transformer can resist without being damaged in the event of a short-circuited
secondary winding.
The rated impulse current Idyn is the highest instantaneous value of the current after a short-circuit whose force
the current transformer can resist without being damaged.
The rated impulse current is specified as peak value.

Siemens LV 14 2017

2/29

 Siemens AG 2016

Measuring Devices
Accessories
4NC current transformers
4NC51 window-type current transformers, used as pin-wound transformers, classes 1 and 3, from 5 A to 75 A

Pin-winding increases the primary current of the current transformer. Consequently, window-type current transformers can
also be used for low primary currents.
Basic type
Rated primary
current
Power
Primary current to
be measured

4NC51 used as
pin-wound transformer

4NC5117
100

4NC5121
150

4NC5122
200

4NC5123
250

2.5

2.5

A
5
10
15

2.5
2.5
2.5
Number of required pin windings
Class 3
10
--5
6
--4
5

Class 1
-10
--

--10

----

----

20
25
30

-2
--

3
-2

-3
--

5
4
--

-6
5

10
8
--

-10
--

40
50
75

----

----

----

-2
--

-3
2

5
4
--

-5
--

A
VA

4NC5112
50

4NC5113
60

4NC5115
75

Selection and ordering data

4NC current transformers for measuring purposes
Rated primary current Ipn

Rating Pn

VA

DT

Article No.
www.siemens.com/
product?Article No.

Price
PU
per PU (UNIT,
SET,
M)

PS*/
P. unit

PG

Weight
per PU
approx.
kg

Classes 1 and 3, from 50 to 1500 A

Rated secondary current 1 A
Class 3
For circular conductors with max. diameter 17.5 mm
For busbars up to 12 10 mm

4NC5112-0BC20

50
60
75

2.5
2.5
2.5

4NC5112-0BC20
4NC5113-0BC20
4NC5115-0BC20

1
1
1

1 unit
1 unit
1 unit

1CL
1CL
1CL

0.424
0.434
0.428

4NC5117-0CC20
4NC5121-0CC20
4NC5122-0CE20
4NC5123-0CE20

1
1
1
1

1 unit
1 unit
1 unit
1 unit

1CL
1CL
1CL
1CL

0.334
0.320
0.358
0.341

4NC5222-0CE20
4NC5223-0CE20
4NC5224-0CE20
4NC5225-0CE20

1
1
1
1

1 unit
1 unit
1 unit
1 unit

1CL
1CL
1CL
1CL

0.456
0.466
0.359
0.371

4NC5325-0CE20
4NC5326-0CE20
4NC5327-0CE20
4NC5328-0CE20

1
1
1
1

1 unit
1 unit
1 unit
1 unit

1CL
1CL
1CL
1CL

0.460
0.417
0.430
0.390

4NC5431-0CH20
4NC5433-0CH20
4NC5434-0CH20

1
1
1

1 unit
1 unit
1 unit

1CL
1CL
1CL

0.664
0.681
0.702

Class 1
For circular conductors with max. diameter 17.5 mm
For 1 busbar up to 12 10 mm

4NC5117-0CC20

100
150
200
250

2.5
2.5
5
5

For circular conductors with max. diameter 28 mm

For 1 busbar up to 30 10 mm
For 2 busbars up to 25 5 mm

4NC5222-0CE20

200
250
300
400

5
5
5
5

For circular conductors with max. diameter 36 mm

For 1 busbar up to 50 10 mm
For 2 busbars up to 40 5 mm
400
500
600
750

5
5
5
5

4NC5325-0CE20
For circular conductors with max. diameter 45 mm
For 1 busbar up to 60 10 mm
For 2 busbars up to 60 10 mm
For 3 busbars up to 60 5 mm
1000
1250
1500

10
10
10

4NC5431-0CH20

2/30

Siemens LV 14 2017

* You can order this quantity or a multiple thereof.

 Siemens AG 2016

Measuring Devices
Accessories
4NC current transformers
4NC51 window-type current transformers, used as pin-wound transformers, classes 1 and 3, from 5 A to 75 A
Rated primary current Ipn

Rating Pn

VA

DT

Article No.
www.siemens.com/
product?Article No.

Price
PU
per PU (UNIT,
SET,
M)

PS*/
P. unit

PG

Weight
per PU
approx.
kg

Rated secondary current 5 A

Class 3
For circular conductors with max. diameter 17.5 mm
For 1 busbar up to 12 10 mm

4NC5112-2BC20

50
60
75

2.5
2.5
2.5

4NC5112-2BC20
4NC5113-2BC20
4NC5115-2BC20

1
1
1

1 unit
1 unit
1 unit

1CL
1CL
1CL

0.429
0.424
0.424

4NC5117-2CC20
4NC5121-2CC20
4NC5122-2CE20
4NC5123-2CE20

1
1
1
1

1 unit
1 unit
1 unit
1 unit

1CL
1CL
1CL
1CL

0.336
0.324
0.349
0.344

4NC5222-2CE20
4NC5223-2CE20
4NC5224-2CE20
4NC5225-2CE20

1
1
1
1

1 unit
1 unit
1 unit
1 unit

1CL
1CL
1CL
1CL

0.461
0.476
0.359
0.374

4NC5325-2CE20
4NC5326-2CE20
4NC5327-2CE20
4NC5328-2CE20

1
1
1
1

1 unit
1 unit
1 unit
1 unit

1CL
1CL
1CL
1CL

0.461
0.415
0.435
0.388

4NC5431-2CH20
4NC5433-2CH20
4NC5434-2CH20

1
1
1

1 unit
1 unit
1 unit

1CL
1CL
1CL

0.656
0.650
0.705

Class 1
For circular conductors with max. diameter 17.5 mm
For 1 busbar up to 12 10 mm

4NC5117-2CC20

100
150
200
250

2.5
2.5
5
5

For circular conductors with max. diameter 28 mm

For 1 busbar up to 30 10 mm
For 2 busbars up to 25 5 mm

4NC5222-2CE20

200
250
300
400

5
5
5
5

For circular conductors with max. diameter 36 mm

For 1 busbar up to 50 10 mm
For 2 busbars up to 40 5 mm
400
500
600
750

5
5
5
5

4NC5325-2CE20
For circular conductors with max. diameter 45 mm
For 1 busbar up to 60 10 mm
For 2 busbars up to 60 10 mm
For 3 busbars up to 60 5 mm
1000
1250
1500

10
10
10

4NC5431-2CH20

More information
Other current transformers for measuring purposes;
see Catalog LV 10, chapter "Switch Disconnectors"

* You can order this quantity or a multiple thereof.

Siemens LV 14 2017

2/31

 Siemens AG 2016

Measuring Devices
Accessories
7KT12 current transformers

Overview
The three-phase 7KT12 current transformer can be used in
distribution boards according to DIN 43880. The measuring
leads are routed vertically through to the standard mounting rail.

This type of current transformer is suitable for infeeds or

outgoing lines in connection with the installation of a 5TE8 switch
or a 5TE1 disconnector, as the primary connecting leads do not
have to be interrupted.
The current transformer is designed for cables of up to 13 mm in
diameter, e.g. H07V-R with 50 mm2 conductor cross-section.

Benefits
The current transformer has accuracy class 1 in accordance
with EN 60044-1.
The versions designed for a transformer ratio of 60/5 A,
100/5 A and 150/5 A enable an even broader range of
applications.
7KT12 current transformers

Technical specifications
7KT1200

7KT1201

7KT1202

2.5

3.75

3 100

3 150

EN 60044-1

Standards
Secondary rated current strength

Accuracy class

Cl.

Rated power

VA

1.25

Rated frequency fn

Hz

50/60

60 Ie

Thermal continuous current

Short-time

1 Ie

Overcurrent limit factor

FS

Rated impulse withstand voltage Uimp

kV

>3

Creepage distances and clearances

mm

>3

Rated operational voltage Ue

V AC

720

Rated operational current Ie

A AC

3 60

Thermal current limit Ith

Terminals screw (Pozidriv)

PZ 1

Conductor cross-sections
- Rigid
- Flexible, with end sleeve
Permissible ambient temperature

mm2
mm2

0.5 ... 4
0.5 ... 2.5

-5 ... +60

Acc. to EN 60068-1

Resistance to climate

20/60/4

Selection and ordering data

Ue

Ie

Isec

Mounting
width

V AC

A AC

A AC

MW

3 60
3 100
3 150

DT Article No.
www.siemens.com/
product?Article No.

Price
per PU

PU
(UNIT,
SET, M)

PS*/
P. unit

PG

Weight
per PU
approx.
kg

Current transformers
720

7KT1200
7KT1201
7KT1202

1
1
1

1 unit
1 unit
1 unit

1BK
1BK
1BK

0.535
0.542
0.558

More information
Other current transformers for measuring purposes;
see Catalog LV 10, chapter "Switch Disconnectors"

2/32

Siemens LV 14 2017

* You can order this quantity or a multiple thereof.

Siemens AG 2016

Software

3/2

3/3
3/5
3/7

3/9
3/10
3/15

Introduction
Configuring, visualizing and
controlling with SIMATIC
Block libraries for SIMATIC
- SIMATIC Modbus/TCP
SENTRON PAC
- PAC/3WL/3VA Library
for SIMATIC PCS 7
Power monitoring with
SIMATIC EnergySuite
- EnergySuite

Configuring, visualizing and

controlling with SENTRON
General data
powermanager
powerconfig

Weitere technische
Produkt-Informationen:
Siemens Industry Online Support:
www.siemens.com/lowvoltage/
product-support
Beitragstyp:
Anwendungsbeispiel
Download
FAQ
Handbuch
Kennlinie
Produktmitteilung
Software-Archiv
Technische Daten
Zertifikat

Siemens LV 14 2017

 Siemens AG 2016

Software
Introduction

Overview
Article No.

Page

6AV6

3/3

3ZS2

3/5

--

3/7

3ZS2

3/10

--

3/15

Configuring, visualizing and controlling with SIMATIC

Block libraries for SIMATIC

The function block libraries enable seamless integration of the 7KM PAC3200/4200
measuring devices into the world of SIMATIC.
SIMATIC Modbus/TCP SENTRON PAC
Software for communication of SIMATIC S7 with devices that support the Modbus/TCP
protocol

PAC/3WL/3VA LIBRARY for SIMATIC PCS 7

The PAC/3WL/3VA function block library enables seamless integration of 3WL/3VA/3VL
circuit breakers and 7KM PAC3200/4200 measuring devices into the PCS 7 process
world.

Power monitoring with SIMATIC EnergySuite

EnergySuite
siemens.de/
energysuite

Ready for
SIMATIC
Energy Suite

Clearly simplified configuration of power-measuring components from the SIMATIC,

SENTRON, SINAMICS, SIRIUS and SIMOCODE product families substantially reduces
configuration effort.

Configuring, visualizing and controlling with SENTRON

powermanager
Powermanager power monitoring software for the power monitoring system with the
following main points:
Identify savings potential
Reduce power costs
Ensure power availability
powerconfig
Commissioning and service tool for communication-capable measuring devices and
circuit breakers with the following main points:
Parameterization, documentation, operation and monitoring of 3WL, 3VA and 3VL
circuit breakers and 7KM PAC3100/3200/4200 measuring devices using various
communication interfaces

3/2

Siemens LV 14 2017

 Siemens AG 2016

Software
Configuring, Visualizing and Controlling with SIMATIC
Block Libraries for SIMATIC
SIMATIC Modbus/TCP SENTRON PAC

Overview

Design

SIMATIC S7-400
with 2x CP443-1

Communication with Modbus/TCP stations takes place via the

SIMATIC S7 CPU's integrated PN interface.

SIMATIC S7-400
with CP443-1

One SIMATIC S7 controller can communicate simultaneously

with several Modbus/TCP stations depending on the number of
connection resources the S7-CPU has.

SIMATIC ET 200S

Modbus
TCP

Industrial
Ethernet

PAC3200

PAC3200

G_I202_XX_36712

SIMATIC S7-300

PAC4200

Software for communication of SIMATIC S7 with devices that

support the Modbus/TCP protocol
Expansion or modification of existing plants with SIMATIC
automation systems
Coupling controllers and systems from different
manufacturers
System requirements
Standard SIMATIC STEP 7 tool Version 5.5 or
SIMATIC TIA Portal Version 11

Benefits
Simple coupling of SENTRON PAC systems with SIMATIC
automation systems via Industrial Ethernet
No specific Modbus know-how required
Engineering with the standard SIMATIC STEP 7 tool
Fast configuration using a wizard

SIMATIC Modbus/TCP SENTRON PAC supports the following

CPUs of the SIMATIC S7:
ET 200
- IM 151-8 PN/DP CPU
- IM 154-8 PN/DP CPU
S7 300/400
- CPU 314C-2 PN/DP
- CPU 315-2 PN/DP
- CPU 317-2 PN/DP
- CPU 319-3 PN/DP
- CPU 412-2 PN
- CPU 414-3 PN/DP
- CPU 416-3 PN/DP
SENTRON PAC
- PAC 3200, firmware V2.2.1 or higher
- PAC 4200, firmware V1.5.1 or higher
Modbus/TCP products have been released for standard CPUs
and for F-CPUs.

Mode of operation
These function blocks are used to enable communication
between a SIMATIC-CPU with an integrated PN interface and
several 7KM PAC measuring devices.
During communication, the data of the basic type 3 and the
energy counters are read and written into S7 data blocks.
Furthermore, defined counters in the 7KM PAC measuring
device can be reset.
Depending on the license procured, the maximum number of
7KM PAC measuring devices that can be connected is
20, 100 or 512.

Application
MODBUS is a protocol that is in use around the world, openly
disclosed to all users and supported by many manufacturers.
For use in modern networks, MODBUS/TCP was developed on
the basis of it. Today, this protocol is an open Internet draft
standard that was introduced to the IETF (Internet Engineering
Task Force), the organization that is responsible for Internet
standardization.
Thanks to this disclosure, any manufacturer and user can implement this protocol, an opportunity that many leading manufacturers have already taken advantage of.
With the increasing expansion of Ethernet communication, both
in industry and in the office, MODBUS/TCP is being adopted to
an ever greater extent in all industries. Heterogeneous system
landscapes are particularly typical areas of use.

Siemens LV 14 2017

3/3

 Siemens AG 2016

Software
Configuring, Visualizing and Controlling with SIMATIC
Block Libraries for SIMATIC
SIMATIC Modbus/TCP SENTRON PAC

Technical specifications
Modbus/TCP SENTRON PAC

Client functionality

Functions

Reading the values of basic type 3 and of the energy counters

Resetting the operating hours counter, the maximum and minimum values and the energy counters

Enabled for multiple instances

Max. number of parallel function block calls

Unlimited number of function block calls

Number of simultaneously established connections depend on the CPU

Connection configuration

Dynamic connections via TCON and TDISCON

Communication

TSEND / TRCV

Memory requirements
(depending on the function block)
FB

31 ... 36 KB

IDB

7 ... 29 KB

Use in CFC / PCS7 possible

Yes

Redundancy functionality

No

Use of bit memories / timers

No

Selection and ordering data

Version

DT Article No.
www.siemens.com/
product?Article No.

Price
per PU

PU
(UNIT,
SET, M)

PS*/
P. unit

PG

Weight
per PU
approx.
kg

SIMATIC Modbus/TCP SENTRON PAC

Modbus/TCP 20 SENTRON PAC

6AV6676-6MA30-0AX0

1 unit

2CP

0.100

6AV6676-6MA30-1AX0

1 unit

2CP

0.100

6AV6676-6MA30-2AX0

1 unit

2CP

0.100

Single license
Communication via the integrated PN interface for reading values out of
PAC 3200 and PAC 4200 devices,
valid for 1 CPU and up to 20 SENTRON PACs
Modbus/TCP 100 SENTRON PAC
Single license
Communication via the integrated PN interface for reading values out of
PAC 3200 and PAC 4200 devices,
valid for 1 CPU and up to 100 SENTRON PACs
Modbus/TCP 512 SENTRON PAC
Single license
Communication via the integrated PN interface for reading values out of
PAC 3200 and PAC 4200 devices,
valid for 1 CPU and up to 512 SENTRON PACs

3/4

Siemens LV 14 2017

* You can order this quantity or a multiple thereof.

 Siemens AG 2016

Software
Configuring, Visualizing and Controlling with SIMATIC
Block Libraries for SIMATIC
PAC/3WL/3VA Library for SIMATIC PCS 7

Overview

Faceplates for circuit breakers (left) and measuring devices (right)

With a driver block, diagnostics block and faceplates, the

PAC/3WL/3VA function block library for SIMATIC PCS 7 enables
seamless integration of 3WL/3VA/3VL circuit breakers and
7KM PAC3200/4200 measuring devices into the SIMATIC PCS 7
process control system.
The blocks that run in the CPUs of the controllers supply the
faceplates in the operator stations of the process control system
with, for example, energy and status data, and they generate
signals and manage the connection to the SIMATIC PCS 7
Maintenance Station.
Note:

Faceplates
The faceplates of the PAC/3WL/3VA function block library for
SIMATIC PCS 7 are used in the operator stations of the process
control system as the user interface for the supported measuring
devices and circuit breakers. The technologically relevant
values and functions of these devices can thus be displayed
and operated as SIMATIC PCS 7 objects.
System-side bidirectional communication connections between
faceplates and blocks, as well as between blocks, measuring
devices and circuit breakers, support display of values in the
faceplates and forwarding of input data to the devices.

The PAC/3WL/3VA Library for SIMATIC PCS 7 can be used

together with SIMATIC PCS 7 V7.1, V8.0, V8.1 and V8.2. It
supports all operating systems of these system versions.

Benefits
Full integration of the 7KM PAC3200/4200 measuring devices
and 3WL/3VA/3VL circuit breakers into the SIMATIC PCS 7
process control system
Connection of all devices via PROFIBUS DPV1 possible
7KM PAC3200/4200 measuring devices and 3VA circuit
breakers can also be integrated via PROFINET
7KM PAC4200 measuring device can be used within the
function range of the 7KM PAC3200 measuring device
Cyclic and acyclic communication (for pure visualization
tasks)
Inputting limit values for monitoring through the driver block
Resetting values on the device (min/max values)
Remote switching of the 3WL and 3VL circuit breakers
Device monitoring and readout of maintenance information
Automatic information in case of overload, short-circuit and
faults
Reading out and displaying device data

Application
The PAC/3WL/3VA Library for SIMATIC PCS 7 is used in all
industries where PCS 7 is used. Full integration in PCS 7 means
that there is no need for a special system environment.
Predefined modules and symbols give you the assurance of
building on tested and certified product components.
For challenging measurements the 7KM PAC4200 can also be
used in the functional scope of the 7KM PAC3200.
In addition to the cyclic connection, there is also an acyclic
connection for pure visualization tasks. The process image of
the SIMATIC CPUs can be used more efficiently with the acyclic
connection.

Siemens LV 14 2017

3/5

 Siemens AG 2016

Software
Configuring, Visualizing and Controlling with SIMATIC
Block Libraries for SIMATIC
PAC/3WL/3VA Library for SIMATIC PCS 7

Selection and ordering data

SIMATIC PCS 7 V8.0, V8.1, V8.2, SIMATIC PCS 7 V7.1
Version

DT Article No.
www.siemens.com/
product?Article No.

Price
per PU

PU
(UNIT,
SET, M)

PS*/
P. unit

PG

Weight
per PU
approx.
kg

Function block library for 7KM PAC3200/4200 measuring devices

and 3WL/3VA/3VL circuit breakers 1)
PAC/3WL/3VA Library for SIMATIC PCS 7

3ZS2787-1CC30-0YG0

1 unit

1DD

0.217

3ZS2787-1CC30-6YH0

1 unit

1DD

0.014

AS blocks and faceplates for integrating the 3WL/3VA/3VL circuit breakers

into SIMATIC PCS 7 V7.1, V8.0 and V8.1 (one required for each
SIMATIC PCS 7 Operator Station of the single station/server version), with:
- Engineering license for one SIMATIC PCS 7 Operator Station of the single
station/server version
- Runtime license for one automation system (1 required per automation
system, further AS runtime licenses can be ordered separately)
Engineering and runtime software, software class A, 2-language (German,
English), single license for one installation
Type of delivery: Software and electronic documentation on CD, engineering
and runtime license as Certificate of License
AS Runtime license for PAC/3WL/3VA Library for SIMATIC PCS 7
For one automation system in each case
Runtime software, software class A, 2-language (German, English), single
license for one installation
Type of delivery: Runtime license as Certificate of License without software
and documentation
1)

Currently supported SIMATIC PCS 7 versions: see

http:/support.automation.siemens.com

More information
Send support requests to
Siemens AG
Energy Management Division
Low Voltage & Products
Nuremberg
Tel.: +49 911 895-7222
Fax: +49 911 895-7223
www.siemens.com/lowvoltage/technical-support
You can find more information on the Internet at:
http://www.siemens.com/lowvoltage

3/6

Siemens LV 14 2017

* You can order this quantity or a multiple thereof.

 Siemens AG 2016

Software
Configuring, Visualizing and Controlling with SIMATIC
Power Monitoring with SIMATIC EnergySuite
EnergySuite

Overview

Gestin

(QHUJ\$QDO\WLFV
6LWHVSDQQLQJDQGHFRQRPLF
FRQVXPSWLRQPDQDJHPHQW

SIMATIC Energy Manager PRO 1)

Processing and monitoring

/LYHFRQVXPSWLRQGLVSOD\
DQGPRQLWRULQJYLD
SDQHODQG6&$'$
SIMATIC Energy Suite

Acquisition

$XWRPDWLRQLQWHJUDWHG
FRQVXPSWLRQGHWHFWLRQ

Measuring devices

SIMATIC Energy Suite

High energy consumption and automated production are typical
of many industries.
Those who wish to take control of their energy costs and who are
already looking towards the digital future today, will equip their
plants with integrated energy measuring technology, thus
anchoring their energy management in the automation of their
production operations where the lion's share of the energy is
consumed. As an integrated option for the TIA Portal, SIMATIC
Energy Suite efficiently links energy management with automation, thus introducing energy transparency to production operations.

siemens.com/
energysuite

Ready for
SIMATIC
Energy Suite

The significantly simplified configuration of power-measuring

components from the SIMATIC, SENTRON, SINAMICS, SIRIUS
and SIMOCODE product families1) substantially reduces configuration effort. Thanks to consistent interfacing to SIMATIC
Energy Manager PRO2) or to the cloud-based Energy Analytics
service, recorded energy data can be expanded seamlessly into
a cross-location energy management system.
This way, businesses can also do justice to all other required
economic and management energy aspects, from purchasing
energy through planning to energy controlling.

1)

Products from the SIMATIC, SENTRON, SINAMICS, SIRIUS and

SIMOCODE product families. You will find details of currently supported
devices here: siemens.com/energysuite-hardware

2)

SIMATIC Energy Manager PRO is the planned and innovative successor of

SIMATIC B.Data

Siemens LV 14 2017

3/7

 Siemens AG 2016

Software
Configuring, Visualizing and Controlling with SIMATIC
Power Monitoring with SIMATIC EnergySuite
EnergySuite

Highlights
Simple and intuitive configuration instead of programming
Automatic generation of the PLC energy program
Convenient integration of measuring components from
the Siemens portfolio and from other manufacturers
Integrated into TIA Portal and the automation system
Archiving in WinCC Professional or PLC
Seamless interfacing to Energy Manager PRO and Energy
Analytics

0ROGHGFDVHFLUFXLW
EUHDNHUV9$
siemens.com/3VA

6,02&2'(
siemens.com/
simocode

0HDVXULQJGHYLFHV
.03$&

siemens.com/sentron

6,5,86VZLWFKLQJGHYLFHV
siemens.com/sirius

6,0$7,&(QHUJ\6XLWH7,$3RUWDO

6,1$0,&6
IUHTXHQF\FRQYHUWHUV
siemens.com/sinamics
6,0$7,&(QHUJ\6XLWH
siemens.com/energysuite

6,0$7,&(QHUJ\
0DQDJHU352
siemens.com/energymanager

Benefits

(QHUJ\$QDO\WLFV
siemens.com/energy-analytics

More information

The advantages at a glance:

Generate energy management data automatically
Integration into TIA Portal and the automation system
Easily configured

3/8

6,0$7,&
(763$,
HQHUJ\PHWHUV
siemens.com/et200sp

Siemens LV 14 2017

For more information on SIMATIC Energy Suite:

www.siemens.com/energysuite

 Siemens AG 2016

Software
Configuring, Visualizing and Controlling with SENTRON
General data

Overview
powermanager
Together with the 7KT/7KM PAC measuring devices, the
powermanager power monitoring software forms the technical
basis for a corporate energy management system in
accordance with ISO 50001, and these are some of the
functions it offers:
Identifying savings potential
Transparency of energy flows
Cutting energy costs
Ensuring power availability

powerconfig
Commissioning and service tool for communication-capable
measuring devices and circuit breakers from the SENTRON
product family with the following advantages:
Facilitates parameterization of the devices, resulting in
considerable time savings, particularly when several devices
have to be set up.
With powerconfig, the 3WL, 3VA, 3VL circuit breakers and the
7KM PAC3100/3200/4200 measuring devices, as well as the
ATC5300 transfer control device can be parameterized,
documented, operated and monitored using various
communication interfaces, as well as tested in the case of the
3VA.

More information
You can find more information on the Internet at:
www.siemens.com/powermonitoring

Siemens LV 14 2017

3/9

 Siemens AG 2016

Software
Configuring, Visualizing and Controlling with SENTRON
powermanager

Overview

Benefits

Integrated reporting to enable you to get started easily

Reports available in .xls, .pdf and .csv formats
Manual and time-driven generation
Templates for:
- Cost center allocation
- Frequency distribution
- Absolute and total energy consumption
- Deviation analysis
- Annual evaluation
- Standard report
Email with generated report via SMTP server (with/without
login) without MS Outlook
Web-based (create, generate, view)

Efficiency in power distribution

SENTRON switching, protection and measuring devices ensure
safety and cost effectiveness in power distribution.
The devices are made even more efficient by software products
for simple and fast configuration, reliable monitoring, or getting
started in energy management and they contribute in this way
to cost savings and increased plant availability.
Characteristic / function

Benefits

Pre-configured project settings

Fast commissioning and easy to get

started

Display of load profile and measured Derivation of measures for saving

variables as a characteristic curve
energy
Predefined reports for the allocation Localizing unnecessary consumption
of consumption and costs to any cost Localizing faults quickly
centers
Increasing energy awareness
Limit monitoring using configurable
alarms

Adapting energy consumption

Avoiding load peaks

Application
System configuration
Operation & monitoring
Windows or Web clients

Ethernet
Data processing
Server

powermanager power
monitoring software

7KT PAC1200
Multichannel
current measuring
system

3VA-line
3VA molded
case circuit
breakers

...

7KM PAC3100
measuring
device

max. 8

Typical topology of a power monitoring system

3/10

I202_01389

Ethernet (Modbus)

Data detection
Measuring/
protection
COM 800
devices

Siemens LV 14 2017

7KM PAC5200
measuring
device
Modbus RS485
7KT PAC1500
measuring
device

7KM PAC5100
measuring
device
3WL air
circuit
breakers

7KM PAC4200
measuring
device
COM 100

3VA-line

7KM PAC3200
measuring
device
3VA
molded case
circuit
breakers

 Siemens AG 2016

Software
Configuring, Visualizing and Controlling with SENTRON
powermanager

Design
Basic Package
The Basic Package contains the software for installation on a server and client and also up to ten devices and one client.
One web and one reports license are also included.
The four option packages can be added to the basic license:

Device Pack
The number of devices can be increased flexibly.

"Expert" option pack

Any number of freely configured system images can be created and displayed.

"Client" option pack

One Windows client serves the purpose of project visualization and configuration of several PCs simultaneously.
The client license resides on the server.

"Distributed Systems" option pack

Linking of several autonomous powermanager systems.
Each system can access and display measured variables and alerts of the other systems.

Siemens LV 14 2017

3/11

 Siemens AG 2016

Software
Configuring, Visualizing and Controlling with SENTRON
powermanager

Function

Independent PC-based energy monitoring for the energy

monitoring system based on Modbus communication
Expandable from the simple standard application to a fully
flexible customer solution
Scalable relative to number of devices and software functions
Optimum integration of 7KT/7KM PAC measuring devices and
3WL/3VL/3VA circuit breakers
Integration of any third-party devices via a generic Modbus
driver
Recording, display, archiving and evaluation of measured
quantities
Monitoring of status and limits, with generation of signals
Manual input of energy values
Virtual computation and devices
Dashboard displays for a fast overview
Defined user interfaces and views of measured values/status

3/12

Siemens LV 14 2017

Control of digital outputs and teleswitching

Load curve display for visualizing archived and online data
User administration with different authorization levels
Distributed multi-server structure
Client-server installation
Access via web browser
OPC interface
Load monitoring
Basic reporting with templates for a simple introduction to the
evaluations
- Cost center allocation
- Evaluations of consumption values
- Deviation analysis
- Annual evaluation
- Frequency distribution
Extended Excel-based reporting for tailored evaluations
Calculation and display of key performance indicators (KPIs)

 Siemens AG 2016

Software
Configuring, Visualizing and Controlling with SENTRON
powermanager

Selection and ordering data

Version

DT Article No.
www.siemens.com/
product?Article No.

Price
PU
per PU (UNIT,
SET,
M)

PS*/
P. unit

PG

Weight
per PU
approx.
kg

powermanager V3.3
Basic package
Full product license for up to 10 devices, installation for client/server, web
access

3ZS2711-0CC30-0YA0

1 unit

1DD

0.222

Device Pack (20)

Device expansion license for up to 20 devices

3ZS2711-0CC30-0YD0

1 unit

1DD

0.139

Device Pack (50)

Device expansion license for up to 50 devices

3ZS2712-0CC30-0YD0

1 unit

1DD

0.140

Device Pack (100)

Device expansion license for up to 100 devices

3ZS2713-0CC30-0YD0

1 unit

1DD

0.140

Device Pack (200)

Device expansion license for up to 200 devices

3ZS2714-0CC30-0YD0

1 unit

1DD

0.141

Device Pack (500)

Device expansion license for up to 500 devices

3ZS2715-0CC30-0YD0

1 unit

1DD

0.144

Device Pack (1000)

Device expansion license for up to 1000 devices

3ZS2716-0CC30-0YD0

1 unit

1DD

0.133

"Expert" option pack

Option for creating/displaying any number of freely configured images

3ZS2710-2CC20-0YH0

1 unit

1DD

0.142

"Client (5)" option pack

Expansion for up to 5 clients

3ZS2710-3CC00-0YD0

1 unit

1DD

0.140

"Distributed Systems (2)" option pack

Option for connection of 2 autonomous powermanager systems
for the exchange of measured values and alarms

3ZS2718-1CC00-0YH0

1 unit

1DD

0.142

"Distributed Systems (5)" option pack

Option for connection of 5 autonomous powermanager systems
for the exchange of measured values and alarms

3ZS2718-2CC00-0YH0

1 unit

1DD

0.142

"Distributed Systems (10)" option pack

Option for connection of 10 autonomous powermanager systems
for the exchange of measured values and alarms

3ZS2718-3CC00-0YH0

1 unit

1DD

0.145

Update license
From V2.0 Lean to V3.0 (10)

3ZS2711-0CC30-0YE0

1 unit

1DD

0.234

Update license
from V2.0 Standard to V3.0 (50)

3ZS2712-0CC30-0YE0

1 unit

1DD

0.227

Update license
from V2.0 Advanced to V3.0 (100)

3ZS2713-0CC30-0YE0

1 unit

1DD

0.231

Update license
from V2.0 Maximum to V3.0 (200)

3ZS2714-0CC30-0YE0

1 unit

1DD

0.226

System 1
Package comprising
- 1 x powermanager Basic Package
- 1 x 7KM PAC4200 (+RS 485 module) and
- 1 x 7KM PAC3100

3ZS2812-5CC20-0AY0

1 unit

1DD

1.310

System 2
Package comprising
- 1 x powermanager Basic Package
- 1 x 7KM PAC4200 (+RS 485 module) and
- 1 x 7KT PAC1500 (+Modbus module)

3ZS2812-6CC20-0YA0

1 unit

1DD

1.230

System 3
Package comprising
- 1 x powermanager Basic Package
- 3 x 7KM PAC 3200

3ZS2813-2CC20-0YA0

1 unit

1DD

1.610

Trial license
Up to 10 devices including "Expert" and "Web" option packs
Full product license limited to 60 days
Available free of charge at
https://support.industry.siemens.com/cs/ww/en/view/64850998

V3.x device expansions

Option packs

powermanager V2.0 to V3.0 update

System packages

* You can order this quantity or a multiple thereof.

Siemens LV 14 2017

3/13

 Siemens AG 2016

Software
Configuring, Visualizing and Controlling with SENTRON
powermanager

More information

New in Version 3.3

Easy start to project creation with a host of pre-defined
settings
Modern, intuitive operator interface with a menu structure and
5 different views and tools
New pre-defined measured value views uniform for all device
types (overview, bar view for energy values, trend view)
Modern color scheme
New internal reporting system for cost center evaluations,
duration curve, deviation analysis, annual evaluation, energy
reports, also available via web browser, in pdf/xls format
Dashboard displays at device and system level
KPI calculations and displays
Direct access to support pages on the Internet
Complete integration of the new 3VA molded case circuit
breaker (ETU5, ETU8) including measured values and
breaker status
Supported operating systems: Windows 7, Windows 8.1,
Windows 10, Windows Server 2008 R2, Windows Server 2012
R2 (64-bit in each case)
Supported EXCEL
- versions: EXCEL 2010, EXCEL 2013 (32-bit in each case)
(necessary for advanced reports)
System requirements
Hardware requirements
Processor: Intel Core i3 processor, 2GHz
RAM: at least 2 GB RAM
Hard disk: HDD with 10 GB free storage space
Display: VGA with at least 1280 x 1024 pixels and 16-bit color
intensity
Supported operating systems
Windows 7: Ultimate / Enterprise / Professional, SP1 (64-bit)
Windows 8.1: Enterprise (64-bit)
Windows 10: Enterprise Pro
Windows Server 2008: Server 2008 R2 (64-bit)
Windows Server 2012: Server 2012 R2 (64-bit)
Supported Excel versions (extended report)
Excel 2010 (32-bit)
Excel 2013 (32-bit)
Available in the following languages
English, German, Simplified Chinese, Turkish, Spanish, French,
Portuguese, Italian

3/14

Siemens LV 14 2017

Internet
Free download for powermanager trial license: see
http://support.automation.siemens.com/WW/view/en/64850998
For more information, see
www.siemens.com/powermanager
www.siemens.com/powermonitoring
German Technical Inspectorate (TV) Certificate of
Conformity for energy management ISO 50001 and energy
audits according to EN 16247-1
The TV Certificate of Conformity confirms that 7KM/7KT PAC
measuring devices, 3VA molded case circuit breakers, 3WL air
circuit breakers and the powermanager power monitoring software support the introduction of a corporate power management
system in accordance with ISO 50001. The ISO 50001 energy
saving standard defines binding criteria for companies for
sustainable energy management.

TV-tested
according to ISO 50001
> Learn more
The TV certificate is available from
http://w3.siemens.com/powerdistribution/global/SiteCollectionDocuments/dokumente-en/SENTRON_Certificate-of-conformity_EN_Text.pdf

 Siemens AG 2016

Software
Configuring, Visualizing and Controlling with SENTRON
powerconfig

Overview
The powerconfig software for commissioning
Software tool for efficient commissioning and diagnosis of communication-capable SENTRON components
License

Free use

Supported devices

7KM PAC3100/3200/4200 measuring devices, incl. expansion modules

3WL/3VL/3VA/ATC5300 circuit breakers

General range of functions

The PC-based tool facilitates parameterization of the devices, resulting in substantial time savings, particularly when several
devices have to be set up.
The device settings can be stored in the PC and printed out.
The tool enables monitoring of instantaneous measured quantities, which can be printed out if required. Execution of specific
device functions, such as resetting of devices and setting of energy counters.

Supported languages

German, English, Chinese, Spanish, Portuguese

Service functions

Firmware updates and switching of language packs for 7KM PAC measuring devices

Functional scope with

7KM PAC4200 and 3VA

Readout of data stored in the device (events; load profile history; daily energy counters), which are saved in csv format

Setting of parameter values

Display of actual measured quantities

The powerconfig software is the combined commissioning and

service tool for communication-capable measuring devices and
circuit breakers from the SENTRON product family.
The PC-based tool facilitates parameterization of the devices,
resulting in substantial time savings, particularly when several
devices have to be set up.

Display of the circuit breaker state

With powerconfig, the 3WL, 3VA and 3VL circuit breakers and
the 7KM PAC 3100/3200/4200 measuring devices with expansion modules and the ATC5300 transfer control device can be
parameterized, documented, operated, and monitored using
various communication interfaces.

Benefits
Parameterization, documentation, operation and monitoring in
one software package, and also testing in the case of the 3VA
User-friendly documentation of measured values and settings
Clear presentation of the available parameters including
validity testing of the inputs
Display of the available device statuses and measured values
in standardized views
Parameterization of all electronic 3VA2 components, e.g.
- ETUs 5-series and 8-series
- COM800/COM100 breaker data servers
- EFB300 (External Function Box).
Support of test functions for 3VA2 using the TD500 test device
for all ETUs
Full support for 3WL air circuit breakers, that is, including
display and triggering of curve shapes and all other functions
Support for the ATC5300 transfer control device
Project-oriented storage of device data
Consistent operation and usability
Support of the various communication interfaces (Modbus
RTU, Modbus TCP, PROFIBUS, PROFINET)
Communication with the 3VA2 circuit breaker via the TD500 at
the USB interface, as a further possibility for Modbus TCP,
PROFIBUS and PROFINET
Supported languages: German, English, Chinese, Spanish,
and Portuguese

Read-out and saving of message lists, load profiles and

characteristic curves (device-dependent)
Overview of circuit breaker states with currents and events
Individually designable system documentation
Update of the device firmware and loading of language packs
(device-dependent)
No programming knowledge required for operation
powerconfig can be started on the PC as follows, with
communication possible via PROFIBUS and PROFINET:
- Directly from Windows
- From STEP 7 V5.5 SP1
- From TIA Portal with STEP 7 V13

Siemens LV 14 2017

3/15

 Siemens AG 2016

Software
Configuring, Visualizing and Controlling with SENTRON
powerconfig

Application
System requirements

Hardware requirements
Processor: Intel Pentium III, 1 GHz (or better)
RAM: at least 512 MB
Hard disk: at least 1 GB free
Color monitor with a minimum resolution of 1024 x 768 pixels
Supported operating systems
Windows XP: XP with SP3 (32-bit)
Windows 7 Professional SP1 (32-bit, 64-bit)
Windows 7 Ultimate SP1 (32-bit, 64-bit)
Windows 2008 Server (32-bit)
Windows 8.1 (64-bit)
Required framework
Microsoft .NET Framework acc. to readme file, currently V4.0

More information
powerconfig is available free of charge at
http://support.automation.siemens.com/WW/view/en/63452759
You can find more information on the Internet at:
www.siemens.com/sentron

3/16

Siemens LV 14 2017

Siemens AG 2016

Appendix

4/2

Catalog notes

4/3

Ordering notes

4/5

Further documentation

4/9

Quality management

4/10

Standards and approvals

4/12

Siemens contacts

4/13

Service & Support

4/14

Comprehensive support
from A to Z

4/15

Software licenses

4/17

Subject index

4/18

Article No. index

incl. export markings

4/20

Conditions of sale and delivery

Siemens LV 14 2017

 Siemens AG 2016

Appendix
Catalog notes

Overview
Trademarks

Symbols

All product designations may be registered trademarks or

product names of Siemens AG or supplier companies whose
use by third parties for their own purposes may violate the rights
of the owner.

In the table below, you will find all symbols concerning

connections that can occur in this catalog. In combination with
orange highlighting, these identify special selection criteria.

Amendments

Connections

Unless stated otherwise on the individual pages of this catalog,

we reserve the right to make changes, in particular to the
specified values, measurements and weights.

Screw connection

Dimensions

Spring-loaded terminals

All dimensions are given in mm.

Illustrations
The illustrations are not binding.
Technical specifications
The technical specifications are for general information
purposes only. Always heed the operating instructions and
notices on individual products during assembly, operation and
maintenance.
Further technical information is available at
www.siemens.com/lowvoltage/product-support
under "Entry type":
- Application example
- Certificate
- Characteristic
- Download
- FAQ
- Manual
- Product note
- Software archive
- Technical data
Configurators can be found under
www.siemens.com/lowvoltage/configurators
Assembly, operation and maintenance
Always heed the operating instructions and notices on individual
products during assembly, operation and maintenance.

4/2

Siemens LV 14 2017

Ring cable lug connection

 Siemens AG 2016

Appendix
Ordering notes

Logistics
General

Packaging, packing units

With regard to delivery service, communications and environmental protection, our logistics service ensures "quality from the
moment of ordering right through to delivery". By designing our
infrastructure according to customer requirements and
implementing electronic order processing, we have successfully
optimized our logistics processes.

The packaging in which our equipment is dispatched provides

protection against dust and mechanical damage during
transport, thus ensuring that all our products arrive in perfect
condition.

We are proud of our personal consulting service, on-time

deliveries and 1-day transport within Germany.
To this end, we supply preferred types marked with } ex
works.
We regard the DIN ISO 9001 certification and consistent quality
checks as an integral part of our services.
Electronic order processing is fast, cost-efficient and error-free.
Please contact us if you want to benefit from these advantages.

We select our packaging for maximum environmental compatibility and reusability (e.g. crumpled paper for protection during
transport in packages up to 32 kg) and, in particular, with a view
to reducing waste.
With our multi-unit and reusable packaging, we offer you specific
types of packaging that are both kind to the environment and
tailored to your requirements:
Your advantages at a glance:
Lower ordering costs.
Cost savings through same-material type packaging:
Low/no disposal costs.
Reduced time and cost thanks to short unpacking times.
"Just-in-time" delivery directly to the production line helps
reduce stock: Cost savings through reduction of storage
areas.
Fast assembly thanks to supply in sets.
Standard Euro boxes - corresponding to the Euro pallet
modular system - suitable for most conveyor systems.
Active contribution to environmental protection.
Unless stated otherwise in the "Selection and ordering data" of
this catalog, our products are supplied individually packed.
For small parts/accessories, we offer you cost-effective
packaging units as standard packs containing more than one
item, e.g. 5, 10, 50 or 100 units. It is essential that whole
number multiples of these quantities be ordered to ensure
satisfactory quality of the products and problem-free order
processing.
The products are delivered in a neutral carton. The label
includes warning notices, the CE marking, and device
descriptions in English and German.
In addition to the Article No. (MLFB) and the number of items in
the packaging, the operating instructions order number
(Instr.-Order-No.) is also specified. They can be obtained from
your local Siemens representative
(you will find a list at www.siemens.com/lowvoltage/contact).
Most device Article No.'s can be obtained by means of the EAN
barcode to simplify ordering and storage logistics.
The associated master data, too, is available from your local
Siemens representative.

Siemens LV 14 2017

4/3

 Siemens AG 2016

Appendix
Ordering notes

Overview

Ordering special versions

Ordering very small quantities

When ordering products that differ from the standard versions

listed in the catalog, "Z" must be added to the Article No.
indicated and the required features must be specified using
alphanumeric order codes or plain text.

When very small orders are placed, the costs associated with
order processing are greater than the order value. We therefore
recommend that you combine several small orders. Where this
is not possible, we regret that we are obliged to make a small
processing charge: for orders with a net goods value of less than
250 we charge an 20 supplement to cover our order
processing and invoicing costs.

Explanations of Selection and Ordering Data

Delivery time class (DT)
Preferred types are device types that can be delivered immediately ex works, i.e. they are dispatched
within 24 hours.

DT

Meaning

Preferred type

Two working days

One week

Three weeks

Six weeks

On request

If ordered in normal quantities, the products are usually delivered within the specified delivery times,
calculated from the date we receive your order.
In exceptional cases, delivery times may vary from those specified.
The delivery times are valid ex works from Siemens AG (products ready for dispatch).
Shipping times depend on the destination and the method of shipping. The standard shipping time for
Germany is one day.
The specified delivery times are correct at the time of going to print and are subject to constant
optimization. Up-to-date information can be found at www.siemens.com/industrymall.

Price units (PU)

The price unit defines the number of units, sets or meters to which the specified price and weight apply.

PS/P. unit (packaging size/packaging unit)

The packaging size/packaging unit defines the number, e.g. of units, sets or meters, contained within outer packaging:
The first digit in the PS/P. unit column (packaging size/packaging unit) indicates the minimum order quantity. You can only order this
specified quantity or a multiple thereof.
The second digit in the PS/P. unit column (packaging size/packaging unit) specifies the number of units contained within the outer
packaging (e.g. in a carton). You must order this quantity or a multiple thereof if you want the items to be delivered in discrete packaging
quantities.
Examples:
PS/P. unit

Meaning

1 unit

You can order one item or a multiple thereof.

5 units

Five units are packed in a bag, for example. Because the bags cannot be opened, you can only order a multiple of
the quantity contained in the bag: 5, 10, 15, 20 etc.

5/100 units

One carton contains (for example) 20 bags, each containing 5 units, i.e. a total of 100 units. If only cartons are
available for delivery, you need to order a multiple of the carton quantity: 100, 200, 300, etc.
Ordering a quantity of 220 units would result in the following delivery: two cartons, each containing 100 units
(= 200 units) and 4 bags, each containing 5 units (= 20 units).

1 set

A set comprises a defined number of different parts.

Price group (PG)

Each product is allocated to a price group.

Weight
The defined weight is the net weight in kg and refers to the price unit (PU).

Examples
DT Article No.

Price
per PU

PU
(UNIT,
SET, M)

PS/
P. unit

PG

Weight
per PU
approx.

1 1/12 units

1BM

0.076

DT Article No.

Price
per PU

PU
(UNIT,
SET, M)

PS/
P. unit

PG

1 unit

1CB

kg
}

3NW7013

DT:

Preferred type

PU:

One unit (on which price is based)

3VA1196-3ED26-0AA0

PU:

One unit (on which price is based)

PS/P. unit: 1 = minimum order quantity / 12 = quantity per

carton

PS/P. unit: 1 = minimum order quantity

PG:

1BM

PG:

Weight
per PU

76 g, always given in kg

1CB

Note:
The article numbers shown here are examples only. They are not necessarily included in this catalog, nor is it essential that their
specifications regarding selection and ordering data be up to date. When ordering, always use the selection and ordering data.

4/4

Siemens LV 14 2017

 Siemens AG 2016

Appendix
Further documentation

Low-Voltage Power Distribution and Electrical Installation Technology on the WWW

We regard product support to be just as important as the
products and systems themselves.
Visit our website for a comprehensive offering of support for
low-voltage power distribution and electrical installation
products, such as:
Overview of the entire product portfolio
Keeping up to date via newsletters, podcasts, blogs and
Twitter
Access to interesting videos on YouTube
Contact with partners around the world
Operating instructions and manuals for direct download
and much more - all conveniently and easily accessible.
www.siemens.com/lowvoltage

Information and Download Center

You will find regularly updated informational material (such as
catalogs and brochures) for low-voltage power distribution and
electrical installations on the Internet at
www.siemens.com/lowvoltage/infomaterial
Here you can order your copy of the available documentation or
download it in common file formats (PDF, ZIP).

Siemens LV 14 2017

4/5

 Siemens AG 2016

Appendix
Further documentation

Product selection using the interactive catalog CA 01

Detailed information together with user-friendly interactive
functions:
The CA 01 interactive catalog covers more than 100,000
products thus providing a comprehensive overview of the
product range offered by Siemens.
You can find everything you need here for solving automation,
switching, installation and drive technology tasks. All information
is provided over a user interface that is both user-friendly and
intuitive.

After selecting the product of your choice you can order at the
press of a button, by fax or by online link.
Information about the interactive catalog CA 01 can be found on
the Internet at:
www.siemens.com/automation/ca01
or on DVD.

Industry Mall
The Industry Mall for online information, product selection
and ordering
Detailed information including product data, illustrations,
certificates and CAx data
Simple configuring of systems
Possible to request individualized quotations
Availability check
Online ordering facility
Order tracking/order overview
Fast access to relevant training offers and services
You can find the Industry Mall on the Internet at
www.siemens.com/industrymall

Industry Online Support

Comprehensive support at any time, whatever your
location
FAQs, sample applications, information about
successor products and product news
Prompt assistance with technical queries
Discussions and best practice sharing with other users in the
forum
Provision of high-quality product data for your planning
programs
Faster access to information with helpful filter and folder
functions in mySupport
Automatic notification service to keep you up to date with the
latest information about topics of interest to you
You can find Siemens Industry Online Support
on the Internet at
www.siemens.com/online-support

4/6

Siemens LV 14 2017

 Siemens AG 2016

Appendix
Further documentation

Industry Online Support App

Main functions at a glance
Scanning of product codes (EAN/QR and data matrix codes)
with direct display of all technical information on the product,
including graphic data (CAx data).
Sending of product information or entries by email, so that the
information can immediately be processed at the workplace.
Submission of queries to Technical Support (Support
Requests). With photo function for transmitting detailed
information.
Contents and interfaces available in six languages
(German, English, French, Italian, Spanish and Chinese)
including option of temporary switchover to English.
Offline cache function for all favorites stored in "mySupport".
These entries can also be retrieved without network reception.
Import of PDF documents into a library
(e.g. iBooks or similar).
You can find information on the Industry Online Support App
on the Internet at
www.siemens.com/industry/onlinesupportapp

Android:

s
Industry Online
Support App
ANDROID

Apple iOS:

Industry Online
Support App
iOS

Windows:

Industry Online
Support App
WINDOWS

Siemens LV 14 2017

4/7

 Siemens AG 2016

Appendix
Further documentation

Product configurator
Finding the right product faster
Complete selection of products and systems based on
technical characteristics or application requirements
Simple, intuitive operation
Option to save the configuration and order lists in a file format
of your choice (txt, pdf, xls, csv)
Direct transfer of the order list into the shopping cart of the
Siemens Industry Mall
Fast access to product data, diagrams, certificates and
CAx data for the selected product and system configuration
Available in multiple languages for use by customers
anywhere in the world

The configurators are available online in the Siemens Industry

Mall and offline in Catalog CA 01.
You can find our configurators at the following website:
www.siemens.com/lowvoltage/configurators

Internal circuit
diagrams

Dimensional
drawings

Operating
instructions

Connection
diagrams

3D models

Product images

Product
master data

Manuals

Data sheets

Characteristic
curves

Certificates

EPLAN Electric
P8 Macros

IC01_00265

CAx Download Manager

You can find the CAx Download Manager on the Internet at

www.siemens.com/lowvoltage/cax

Time savings of up to 80% with universal product data for your

CAE and CAD systems
The CAx Download Manager can supply you with all the
necessary CAx file types for the products of your choice for use
in all common CAE and CAD systems free of charge in just four
selection steps. The data is updated on a daily basis. All your
selected files are packed into a zip file which you can download
for further use.
Siemens makes up to 12 file types available around the clock to
support your mechanical (CAD) and electrical (CAE) planning
processes.
No manual data collection necessary
Universal manufacturer data for all common CAE and
CAD systems
Standardized documentation is simple to generate
Choice of different languages for system commissioning
anywhere in the world

My Documentation Manager
User-friendly compilation of project-specific documentation
In accordance with directives*, the documentation is part of the
plant and requires certification, thus giving the purchaser the
right to full plant documentation.
To support you in this, a manual configurator has been
developed with which you can put together individual and
standard-compliant documentation fully in accordance with
the relevant project-specific requirements.

In "mySupport" you can compile individual documentation for

your project by dragging and dropping
* e.g. Low Voltage Directive 2006/95/EC and EC Machinery
Directive 2006/42/EC
You can find My Documentation Manager on the Internet at
www.siemens.com/lowvoltage/mdm

4/8

Siemens LV 14 2017

You can thus select the chapters relevant to the respective

project from the available manuals of the installed Siemens
components. FAQs, certificates, data sheets and your own
content can also be incorporated.
Compile and structure manuals, data sheets, FAQs and
certificates simply by dragging and dropping
Insert personalized content via the Notes function
Further processing possible thanks to selectable export
formats (pdf, xml, rtf)
After generating the documentation, automatic translation into
the desired language is possible
Always up-to-the minute thanks to the Update function

 Siemens AG 2016

Appendix
Quality management

Overview
The quality management system of our "Low Voltage & Products"
Business Unit in the "Energy Management" Division complies
with the international EN ISO 9001 standard.
The products and systems listed in this catalog are developed
and manufactured using a certified quality management system
in accordance with EN ISO 9001:2008.

Siemens LV 14 2017

4/9

 Siemens AG 2016

Appendix
Standards and approvals

Overview
Certificates
An overview, updated on a daily basis, of our products certified
in accordance with CE, UL, CSA, FM, shipping authorizations
etc. for low-voltage power distribution and electrical installation
products can be found on the Internet at
www.siemens.com/lowvoltage/certificates

In the Entry list, you can filter the view in order to quickly find
comprehensive information on the following subjects:
Product or search term
Date
Type of certificate (general product approval, test certificates,
shipping approval, ...)
Certificate (confirmations, UL, VDE,...)
Approval office (TV, VDE, UL, ...)
Country

4/10

Siemens LV 14 2017

 Siemens AG 2016

Appendix
Standards and approvals

Approval requirements valid in different countries

Siemens low-voltage switchgear and controlgear are designed,
manufactured and tested according to the relevant German
standards (DIN and VDE), IEC publications and European
standards (EN) as well as CSA and UL standards. You will find
the standards assigned to the single devices in the relevant
certificates at
www.siemens.com/lowvoltage/certificates
In addition to the pertinent VDE, EN and IEC standards, the
requirements of the various regulations valid in other countries
have also been taken into account in the design of the
equipment in some cases, in order that the devices can be
deployed globally as far as possible.
In some countries an approval is required for certain low-voltage
switchgear and controlgear components. Depending on the
market requirements, these devices have been submitted for
approval to the authorized testing institutes.

In some cases, CSA for Canada and UL for the USA only
approve special versions. Such special versions are listed
separately from the standard versions in the relevant parts of this
catalog.
For this equipment, there are sometimes limits with regard to the
maximum permissible voltages, currents and rated outputs or
special approvals and, in some cases, special identification may
be required.
For use on board ship, the specifications of the marine
classification societies must be observed. In some cases, they
require type tests of the components to be approved.
For more information on UL, visit
www.siemens.com/applicationconsulting/ul
If you have any questions concerning UL/CSA approvals, please
contact Technical Support:
www.siemens.com/lowvoltage/contact

Siemens LV 14 2017

4/11

 Siemens AG 2016

Appendix
Siemens contacts

Contacts for low-voltage power distribution and electrical installation technology

With low-voltage power distribution and electrical installation
technology we consistently pursue one goal:
long-term improvement of your competitive ability.
We are committed to this goal. Thanks to our dedication, we are
continually setting new standards. In all industries worldwide.
At your service, locally, around the globe: Partners for
consulting, sales, training, service, support, spare parts ... on
the entire range of low-voltage power distribution and electrical
installation technology.

Your personal contact can be found in our Contact Database at

www.siemens.com/lowvoltage/contact
You start by selecting a
Required competence
Product or sector
Country
City
or by performing a
search for a specific location or
individual.

4/12

Siemens LV 14 2017

 Siemens AG 2016

Appendix
Service & Support
Unrivaled complete range of services over the entire life cycle

Industry Online Support

Industry Online Support is an

extensive information system for
all questions relating to
products, systems and solutions
developed for industry by
Siemens.

Field Service

Siemens Field Service offers

support with all aspects of
maintenance so that the
availability of your machines
and plants is assured whatever
the case.

4
You will find further information at
www.siemens.com/online-support
www.siemens.com/lowvoltage/product-support

Technical Support

The competent consulting

service for technical issues with
a broad range of customeroriented services for all our
products and systems.

You will find further information at

www.siemens.com/lowvoltage/contact

Spare Parts
Plants and systems in all
industries worldwide are
expected to meet ever higher
levels of availability.
We can help you rule out
unexpected stoppages: with a
global network and optimum
logistics chains.

You will find further information at

www.siemens.com/lowvoltage/contact

Training

Extend your lead with practical

know-how straight from the
manufacturer.

You will find further information at

www.siemens.com/lowvoltage/contact

Specification texts

You can obtain qualified, free support to help you produce

specifications for technically equipping non-residential and
industrial buildings at
www.siemens.com/specifications

You will find further information at

www.siemens.com/lowvoltage/training

Siemens LV 14 2017

4/13

 Siemens AG 2016

Appendix
Comprehensive support from A to Z

Overview
Product information
Fast and targeted information on low-voltage power
distribution and electrical installation technology:

Website

www.siemens.com/lowvoltage
Always up to date about our trend-setting products
and systems:

Newsletter

www.siemens.com/lowvoltage/newsletter

Product information/product & system selection

Information and
Download Center

Current information
(e.g. catalogs and brochures):
www.siemens.com/lowvoltage/infomaterial

Industry Mall

Comprehensive information and order platform for

the Siemens Industry Basket:
www.siemens.com/lowvoltage/mall
Every product for automation and drive technology,
interactive catalog, DVD

CA 01

Product and system engineering

SIMARIS
Planning tools

Support in planning and configuring

electrical power distribution:
www.siemens.com/simaris

SIMARIS
configuration
configuration
software

Support throughout the entire configuration cycle

from the configuration of ALPHA distribution boards
and SIVACON S4 power distribution boards, cost
calculations and quotation preparation, right through
to the creation of plant documentation:
www.siemens.com/simarisconfig

Software for power

loss calculations SIMARIS therm

Support in performing power loss calculations for the

dimensioning of control cabinets:
www.siemens.com/simaristherm

Product documentation
Siemens Industry
Online Support

Comprehensive technical information - from planning

to configuration and operation:
www.siemens.com/online-support
www.siemens.com/lowvoltage/product-support

Product configurator Complete selection of products and systems based

on technical characteristics or application
requirements:
www.siemens.com/lowvoltage/configurators
CAx Download
Manager

Collation of CAx data types for

standard CAE and CAD systems:
www.siemens.com/lowvoltage/cax

My Documentation
Manager

Compilation of project-specific documentation:

Image database

Collection of product photographs and graphics,

such as dimensional drawings and internal circuit
diagrams:

www.siemens.com/lowvoltage/mdm

www.siemens.com/lowvoltage/picturedb

Product training
SITRAIN Portal

Comprehensive training program for our products,

systems and engineering tools:
www.siemens.com/lowvoltage/training

Product hotline
Technical Support

Support for all technical queries

about our products:
www.siemens.com/lowvoltage/contact
www.siemens.com/lowvoltage/technical-support

4/14

Siemens LV 14 2017

 Siemens AG 2016

Appendix
Software licenses

Overview
Software types
Software requiring a license is categorized into types.
The following software types have been defined:
Engineering software
Runtime software
Engineering software
This includes all software products for creating (engineering)
user software, e.g. for configuring, programming, parameterizing, testing, commissioning or servicing.
Data generated with engineering software and executable
programs can be duplicated for your own use or for use by thirdparties free-of-charge.
Runtime software
This includes all software products required for plant/machine
operation, e.g. operating system, basic system, system expansions, drivers, etc.
The duplication of the runtime software and executable programs created with the runtime software for your own use or for
use by third-parties is subject to a charge.
You can find information about license fees according to use in
the ordering data (e.g. in the catalog). Examples of categories of
use include per CPU, per installation, per channel, per instance,
per axis, per control loop, per variable, etc.
Information about extended rights of use for parameterization/configuration tools supplied as integral components of the
scope of delivery can be found in the readme file supplied with
the relevant product(s).
License types
Siemens Industry Automation & Drive Technologies offers various types of software license:
Floating license
Single license
Rental license
Rental floating license
Trial license
Demo license
Demo floating license
Floating license
The software may be installed for internal use on any number of
devices by the licensee. Only the concurrent user is licensed.
The concurrent user is the person using the program. Use
begins when the software is started.
A license is required for each concurrent user.
Single license
Unlike the floating license, a single license permits only one
installation of the software per license.
The type of use licensed is specified in the ordering data and
in the Certificate of License (CoL). Types of use include for
example per instance, per axis, per channel, etc.
One single license is required for each type of use defined.
Rental license
A rental license supports the "sporadic use" of engineering
software. Once the license key has been installed, the software
can be used for a specific period of time (the operating hours do
not have to be consecutive).
One license is required for each installation of the software.

Rental floating license

The rental floating license corresponds to the rental license,
except that a license is not required for each installation of the
software. Rather, one license is required per object (for example,
user or device).
Trial license
A trial license supports "short-term use" of the software in a nonproductive context, e.g. for testing and evaluation purposes.
It can be transferred to another license.
Demo license
The demo license support the "sporadic use" of engineering software in a non-productive context, for example, use for testing
and evaluation purposes. It can be transferred to another
license. After the installation of the license key, the software can
be operated for a specific period of time, whereby usage can be
interrupted as often as required.
One license is required per installation of the software.
Demo floating license
The demo floating license corresponds to the demo license,
except that a license is not required for each installation of the
software. Rather, one license is required per object (for example,
user or device).
Certificate of license (CoL)
The CoL is the licensee's proof that the use of the software has
been licensed by Siemens. A CoL is required for every type of
use and must be kept in a safe place.
Downgrading
The licensee is permitted to use the software or an earlier version/release of the software, provided that the licensee owns
such a version/release and its use is technically feasible.
Delivery versions
Software is constantly being updated.
The following delivery versions
PowerPack
Upgrade
can be used to access updates.
Existing bug fixes are supplied with the ServicePack version.
PowerPack
PowerPacks can be used to upgrade to more powerful software.
The licensee receives a new license agreement and CoL
(Certificate of License) with the PowerPack. This CoL, together
with the CoL for the original product, proves that the new software is licensed.
A separate PowerPack must be purchased for each original
license of the software to be replaced.
Upgrade
An upgrade permits the use of a new version of the software on
the condition that a license for a previous version of the product
is already held.
The licensee receives a new license agreement and CoL with
the upgrade. This CoL, together with the CoL for the previous
product, proves that the new version is licensed.
A separate upgrade must be purchased for each original license
of the software to be upgraded.

Siemens LV 14 2017

4/15

 Siemens AG 2016

Appendix
Software licenses

Overview
ServicePack
ServicePacks are used to debug existing products.
ServicePacks may be duplicated for use as prescribed according to the number of existing original licenses.
License key

Siemens Industry Automation & Drive Technologies supplies

software products with and without license keys.
The license key serves as an electronic license stamp and
is also the "switch" for activating the software (floating license,
rental license, etc.).
The complete installation of software products requiring license
keys includes the program to be licensed (the software) and the
license key (which represents the license).

4/16

Siemens LV 14 2017

Software Update Service (SUS)

As part of the SUS contract, all software updates for the respective product are made available to you free of charge for a period
of one year from the invoice date. The contract will automatically
be extended for one year if it is not canceled three months
before it expires.
The possession of the current version of the respective software
is a basic condition for entering into an SUS contract.
You can download explanations concerning license conditions from
www.siemens.com/automation/salesmaterial-as/catalog/en/
terms_of_trade_en.pdf

 Siemens AG 2016

Appendix
Subject index
A
App
Siemens Industry Online Support App................................................... 4/7
Applications ................................................................................................ 1/4
B
Basic package.......................................................................................... 3/13
Bus systems................................................................................................ 1/4
C
CAx Download Manager............................................................................. 4/8
Communication modules for E-counters .................................................. 2/25
Controlling................................................................................................... 1/3
Current transformers................................................................................. 2/32
4NC ...................................................................................................... 2/29
7KT1 2 .................................................................................................. 2/32
D
Device expansions ................................................................................... 3/13
E
E-counter ......................................................................................... 2/20, 2/23
Three-phase ................................................................................ 2/20, 2/23
Energy costs ............................................................................................... 3/9
Energy counters............................................................................... 2/20, 2/23
Three-phase ................................................................................ 2/20, 2/23
Energy efficiency ........................................................................................ 1/3
Energy manager ......................................................................................... 1/3
Energy Suite................................................................................................ 3/7
Expansion module
For E-counters ...................................................................................... 2/25
For power monitoring devices.............................................................. 2/13
G
German Energy Services Act ..................................................................... 1/2
I
Industry Mall ............................................................................................... 4/6
Industry Online Support.............................................................................. 4/6
Information and Download Center.............................................................. 4/5
Instabus KNX ............................................................................................ 2/25
ISO 50001 ............................................................................................ 1/2, 1/3
L
LAN couplers ............................................................................................ 2/27
Library
PAC3200 for SIMATIC PCS 7.................................................................. 3/5
Low-voltage power distribution and electrical installation technology on the
WWW .......................................................................................................... 4/5

P
PAC
1200 ..................................................................................................... 2/17
1500 ..................................................................................................... 2/22
3100 ....................................................................................................... 2/4
3200 ....................................................................................................... 2/5
4200 ....................................................................................... 2/7, 2/9, 2/10
PROFIBUS DP ...................................................................................... 2/13
Power availability ........................................................................................ 3/9
Power management ............................................................ 1/2, 1/3, 1/9, 1/11
Power management system ....................................................... 1/3, 1/9, 1/11
Power monitoring devices
PAC3100 ................................................................................................ 2/4
PAC3200 ................................................................................................ 2/5
PAC4200 ................................................................................ 2/7, 2/9, 2/10
Product configurator................................................................................... 4/8
PROFIBUS DP .......................................................................................... 1/11
PROFIenergy ............................................................................................ 1/11
R
Recording ................................................................................................... 1/4
RS 485 ...................................................................................................... 2/25
RS 485 interface ....................................................................................... 1/10
S
Savings potential ........................................................................................ 3/9
Siemens Industry Online Support App....................................................... 4/7
SIMATIC Energy Suite ................................................................................ 3/7
SIMATIC EnergySuite ................................................................................. 3/2
SIMATIC Modbus/TCP SENTRON PAC ...................................................... 3/3
Standards and approvals ......................................................................... 4/10
Switching states ......................................................................................... 1/4
System packages ..................................................................................... 3/13
T
Technical specifications ............................................................................. 1/6
Three-phase counters, PAC1500 .................................................... 2/17, 2/22
Three-phase measuring devices
Current transformers ............................................................................ 2/32
E-counter..................................................................................... 2/20, 2/23
LAN couplers ....................................................................................... 2/27
Trial license............................................................................................... 3/13
TV certification ....................................................................................... 1/10
U
Update license ......................................................................................... 3/13

M
M-Bus........................................................................................................ 2/25
Measuring device, 7KT PAC1500, single-phase ...................................... 2/24
Monitoring ................................................................................................... 1/4
Multi-site power monitoring......................................................................... 1/5
My Documentation Manager ...................................................................... 4/8
O
Optimization measures ............................................................................... 1/4
Option pack .............................................................................................. 3/13

Siemens LV 14 2017

4/17

 Siemens AG 2016

Appendix
Article No. index incl. export markings

Overview
Article No.

Page

Article No.

Export markings
ECCN

AL

Export markings
ECCN

AL

4NC5433-0CH20

2/30

3ZS2710-2CC20-0YH0

3/13

EAR99

4NC5433-2CH20

2/31

3ZS2710-3CC00-0YD0

3/13

EAR99

4NC5434-0CH20

2/30

4NC5434-2CH20

2/31

6AV

3ZS

Page

3ZS2711-0CC30-0YA0

3/13

EAR99

3ZS2711-0CC30-0YD0

3/13

EAR99

3ZS2711-0CC30-0YE0

3/13

EAR99

6AV6676-6MA30-0AX0

3/4

3ZS2712-0CC30-0YD0

3/13

EAR99

6AV6676-6MA30-1AX0

3/4

3ZS2712-0CC30-0YE0

3/13

EAR99

6AV6676-6MA30-2AX0

3/4

3ZS2713-0CC30-0YD0

3/13

EAR99

7KM

3ZS2713-0CC30-0YE0

3/13

EAR99

7KM2111-1BA00-3AA0

2/6

EAR99

2/6

EAR99

3ZS2714-0CC30-0YD0

3/13

EAR99

7KM2112-0BA00-2AA0

3ZS2714-0CC30-0YE0

3/13

EAR99

7KM2112-0BA00-3AA0

2/6

EAR99

3ZS2715-0CC30-0YD0

3/13

EAR99

7KM3133-0BA00-3AA0

2/4

EAR99

3ZS2716-0CC30-0YD0

3/13

EAR99

7KM4211-1BA00-3AA0

2/8

EAR99

3ZS2718-1CC00-0YH0

3/13

EAR99

7KM4212-0BA00-2AA0

2/8

EAR99

2/8

EAR99

3ZS2718-2CC00-0YH0

3/13

EAR99

7KM4212-0BA00-3AA0

3ZS2718-3CC00-0YH0

3/13

EAR99

7KM5212-6BA00-1EA2

2/9

EAR99

3ZS2787-1CC30-0YG0

3/6

7KM5212-6CA00-1EA8

2/9

EAR99

3ZS2787-1CC30-6YH0

3/6

7KM5412-6BA00-1EA2

2/11

3ZS2812-5CC20-0AY0

3/13

5D992

7KM5412-6CA00-1EA8

2/11

7KM9200-0AB00-0AA0

2/15

EAR99

7KM9300-0AB01-0AA0

2/15

EAR99

7KM9300-0AE01-0AA0

2/15

EAR99

3ZS2812-6CC20-0YA0
3ZS2813-2CC20-0YA0

3/13
3/13

5D992
5D992

4NC
4NC5112-0BC20

2/30

7KM9300-0AM00-0AA0

2/15

EAR99

4NC5112-2BC20

2/31

7KM9900-0GA00-0AA0

2/12

4NC5113-0BC20

2/30

7KM9900-0SA00-0AA0

2/12

EAR99

7KM9900-0XA00-0AA0

2/12

7KM9900-0YA00-0AA0

2/12

4NC5113-2BC20

2/31

4NC5115-0BC20

2/30

4NC5115-2BC20

2/31

4NC5117-0CC20

2/30

4NC5117-2CC20

2/31

4NC5121-0CC20

2/30

4NC5121-2CC20

2/31

4NC5122-0CE20

2/30

4NC5122-2CE20

2/31

4NC5123-0CE20

2/30

4NC5123-2CE20

2/31

4NC5222-0CE20

2/30

4NC5222-2CE20

2/31

4NC5223-0CE20

2/30

4NC5223-2CE20

2/31

4NC5224-0CE20

2/30

4NC5224-2CE20

2/31

4NC5225-0CE20

2/30

4NC5225-2CE20

2/31

4NC5325-0CE20

2/30

4NC5325-2CE20

2/31

4NC5326-0CE20

2/30

4NC5326-2CE20

2/31

4NC5327-0CE20

2/30

4NC5327-2CE20

2/31

4NC5328-0CE20

2/30

4NC5328-2CE20

2/31

4NC5431-0CH20

2/30

4NC5431-2CH20

2/31

4/18

Siemens LV 14 2017

 Siemens AG 2016

Appendix
Article No. index incl. export markings
Article No.

Page

Export markings
ECCN

AL

7KT
7KT1200

2/32

7KT1201

2/32

7KT1202

2/32

7KT1222

2/20

7KT1223

2/20

7KT1233

2/20

7KT1236

2/20

7KT1238

2/20

7KT1242

2/20

7KT1254

2/20

7KT1255

2/20

7KT1260

2/20

7KT1391

2/27

7KT1530

2/24

7KT1531

2/24

7KT1533

2/24

7KT1540

2/23

7KT1542

2/23

7KT1543

2/23

7KT1545

2/23

7KT1546

2/23

7KT1548

2/23

7KT1900

2/25

7KT1903

2/25

7KT1907

2/25

7KT1908

2/25

A product's export markings are updated daily at

www.siemens.com/industrymall.

Siemens LV 14 2017

4/19

 Siemens AG 2016

Appendix
Conditions of sale and delivery

1. General standards

By using this catalog you can acquire hardware and software

products described therein from Siemens AG subject to these
conditions of sale and delivery (hereinafter: CSD). Please note:
the scope, the quality and the conditions for supplies and
services, including software products, by any Siemens group or
Regional Company having a registered office outside of
Germany, shall be subject exclusively to the General Terms and
Conditions of the respective Siemens entity. These CSD apply
exclusively for orders placed with Siemens AG, Germany.
1.1 For customers with a seat or registered office in
Germany
For customers with a seat or registered office in Germany, the
following shall be subordinate to these CSD
the "General Terms of Payment"1) and
for software products, the "General License Conditions for
Software Products for Automation and Drives for Customers
with a Seat or Registered Office in Germany"1) and
the "General Conditions for the Supply of Products and
Services of the Electrical and Electronics Industry"1) for other
deliveries and services.
1.2 For customers with a seat or registered office outside of
Germany
For customers with a seat or registered office outside of
Germany, the following shall be subordinate to these CSD
the "General Terms of Payment"1) and
for software products, the "General License Conditions for
Software Products for Automation and Drives for Customers
with a Seat or Registered Office outside of Germany"1) and
the "General Conditions for Supplies of Siemens Industry for
Customers with a Seat or Registered Office outside of
Germany"1) for other deliveries and services.

2. Prices
The prices are in (Euro) ex works, excluding packaging.
The sales tax (value added tax) is not included in the prices. It
shall be debited separately at the respective rate according to
the applicable legal regulations.
Prices are subject to change without prior notice. We will debit
the prices valid at the time of delivery.
To compensate fluctuating prices of raw materials (for example
silver, copper, aluminum, lead, gold, dysprosium and
neodymium), surcharges are calculated on a daily basis for
products containing these raw materials using the metal factor.
A surcharge for the particular raw material is added to the price
of a product if the basic quotations for this raw material are
exceeded.
Each product's metal factor dictates for which raw materials the
metal surcharges are calculated, from which quotation and with
which calculation method (weight or percentage method).
An exact explanation of the metal factor can be found on the
page entitled "Metal surcharges".
The surcharge will be calculated (except in the case of
dysprosium and neodymium) on the basis of the official price on
the day prior to receipt of the order or prior to the release order
for calculation of the surcharge.
In the event of placement of an order, the relevant three-month
average price from the quarter prior to order receipt or the
release order shall be used with a one-month buffer to calculate
the dysprosium and neodymium surcharge ("rare earths") (you
will find details in the aforementioned explanation of the metal
factor).

4/20

Siemens LV 14 2017

3. Additional terms and conditions

All dimensions are in mm. In Germany, according to the German
law on units in metrology, data in inches only apply to devices for
export.
Illustrations are not binding.
Insofar as there are no remarks on the corresponding pages of
this catalog - especially with regard to data, dimensions and
weights given - these are subject to change without prior notice.

4. Export regulations
We shall not be obligated to fulfill this agreement if such
fulfillment is prevented by any impediments arising out of
national or international foreign trade or customs requirements
or any embargoes or other sanctions.
Export of the products listed in this catalog may be subject to
authorization. In delivery information, we label authorization
obligations according to German, European and US export lists.
Goods labeled with an "AL" not equal to "N" are subject to
European or German export authorization when being exported
out of the EU. Goods labeled with "ECCN" not equal to "N" are
subject to a US re-export authorization.
Please note that you can also preview the export designations in
the respective product description via our "Industry Mall" online
catalog system. The deciding factors, however, are the AL or
ECCN export designations indicated on order confirmations,
delivery notes and invoices.
Even if goods are not labeled, or labeled "AL:N" or "ECCN:N",
they may still be subject to export authorization based on the
final destination and end use of the goods.
If you transfer goods (hardware and/or software and/or
technology as well as corresponding documentation, regardless
of the mode of provision) delivered by us or works and services
(including all kinds of technical support) performed by us to a
third party worldwide, you shall comply with all applicable
national and international (re-) export control regulations.
If required to conduct export control checks, you, at our request,
shall promptly provide us with all information pertaining to
particular end customers, destination and intended use of
goods, works and services provided by us, as well as any
relevant export control restrictions.
The products listed in this catalog may be subject to
European/German and/or US export regulations. Therefore, any
export requiring a license is subject to approval by the
competent authorities.
Errors excepted and subject to change without prior notice.

1)

You can download the text of the Siemens AG terms and conditions of
trade at
www.siemens.com/automation/salesmaterialas/catalog/en/terms_of_trade_en.pdf

 Siemens AG 2016

Catalogs
Digital Factory, Process Industries and Drives and Energy Management
Further information can be obtained from our branch offices www.siemens.com/lowvoltage/contact
Interactive Catalog on DVD
Products for Automation and Drives
Building Control
GAMMA Building Control
Drive Systems
SINAMICS G130 Drive Converter Chassis Units
SINAMICS G150 Drive Converter Cabinet Units
SINAMICS GM150, SINAMICS SM150
Medium-Voltage Converters
SINAMICS PERFECT HARMONY GH180
Medium-Voltage Air-Cooled Drives (Germany Edition)

Catalog
CA 01

ET G1

D 11
D 12
D 15.1

SINAMICS G180
Converters Compact Units, Cabinet Systems,
Cabinet Units Air-Cooled and Liquid-Cooled
SINAMICS S120 Chassis Format Units and
Cabinet Modules
SINAMICS S150 Converter Cabinet Units
SINAMICS S120 and SIMOTICS
SINAMICS DCM DC Converter, Control Module
SINAMICS DCM Cabinet
SINAMICS Inverters for Single-Axis Drives and
SIMOTICS Motors
SINAMICS G120P and SINAMICS G120P Cabinet
pump, fan, compressor converters
LOHER VARIO High Voltage Motors
Flameproof, Type Series 1PS4, 1PS5, 1MV4 and 1MV5
Frame Size 355 to 1000, Power Range 80 to 7100 kW

D 18.1

Three-Phase Induction Motors SIMOTICS HV,

SIMOTICS TN
Series H-compact
Series H-compact PLUS
High Voltage Three-phase Induction Motors
SIMOTICS HV Series A-compact PLUS
Three-Phase Induction Motors SIMOTICS HV,
Series H-compact
Synchronous Motors with Permanent-Magnet
Technology, HT-direct
DC Motors
SIMOREG DC MASTER 6RA70 Digital Chassis
Converters
SIMOREG K 6RA22 Analog Chassis Converters
Digital: SIMOREG DC MASTER 6RM70 Digital
Converter Cabinet Units
SIMOVERT PM Modular Converter Systems
SIEMOSYN Motors
MICROMASTER 420/430/440 Inverters
MICROMASTER 411/COMBIMASTER 411

D 84.1

D 21.3

D 21.4
D 23.1
D 23.2
D 31
D 35
D 83.2

Catalog

SENTRON SIVACON ALPHA

Protection, Switching, Measuring and Monitoring
Devices, Switchboards and Distribution Systems
Standards-Compliant Components for
Photovoltaic Plants
Electrical Components for the Railway Industry
Power monitoring made simple
Components for Industrial Control Panels according
to UL Standards
3WT Air Circuit Breakers up to 4000 A
3VT Molded Case Circuit Breakers up to 1600 A
Digital: SIVACON System Cubicles, System Lighting
and System Air-Conditioning
Digital: ALPHA Distribution Systems
ALPHA FIX Terminal Blocks
SIVACON S4 Power Distribution Boards
SIVACON 8PS Busbar Trunking Systems
Digital: DELTA Switches and Socket Outlets
Vacuum Switching Technology and Components
for Medium Voltage
Motion Control
SINUMERIK 840
Equipment for Machine Tools
SINUMERIK 808
Equipment for Machine Tools
SINUMERIK 828
Equipment for Machine Tools
SIMOTION
Equipment for Production Machines
Digital: Drive and Control Components for Cranes

LV 10

LV 11
LV 12
LV 14
LV 16
LV 35
LV 36
LV 50
LV 51
LV 52
LV 56
LV 70
ET D1
HG 11.01

NC 62
NC 81.1
NC 82
PM 21
CR 1

D 84.9
D 86.1
D 86.2
DA 12
DA 21.1
DA 21.2
DA 22
DA 45
DA 48
DA 51.2
DA 51.3

Low-Voltage Three-Phase-Motors
SIMOTOCS S-1FG1 Servo geared motors
SIMOTICS Low-Voltage Motors
SIMOTICS FD Low-Voltage Motors
LOHER Low-Voltage Motors
MOTOX Geared Motors
SIMOGEAR Geared Motors
SIMOGEAR Gearboxes with adapter

D 41
D 81.1
D 81.8
D 83.1
D 87.1
MD 50.1
MD 50.11

Mechanical Driving Machines

FLENDER Standard Couplings
FLENDER High Performance Couplings
FLENDER Backlash-free Couplings
FLENDER SIP Standard industrial planetary gear units

MD 10.1
MD 10.2
MD 10.3
MD 31.1

Process Instrumentation and Analytics

Digital: Field Instruments for Process Automation
Digital: SIPART Controllers and Software
Products for Weighing Technology
Digital: Process Analytical Instruments
Digital: Process Analytics, Components for Continuous
Emission Monitoring

Low-Voltage Power Distribution and

Electrical Installation Technology

FI 01
MP 31
WT 10
AP 01
AP 11

Power Supply
SITOP Power supply

KT 10.1

Safety Integrated
Safety Technology for Factory Automation

SI 10

SIMATIC HMI / PC-based Automation

Human Machine Interface Systems/
PC-based Automation

ST 80/
ST PC

SIMATIC Ident
Industrial Identification Systems

ID 10

SIMATIC Industrial Automation Systems

Products for Totally Integrated Automation
SIMATIC PCS 7 Process Control System
System components
SIMATIC PCS 7 Process Control System
Technology components
Add-ons for the SIMATIC PCS 7
Process Control System

ST 70
ST PCS 7
ST PCS 7 T
ST PCS 7 AO

SIMATIC NET
Industrial Communication

IK PI

SIRIUS Industrial Controls

Digital: SIRIUS Industrial Controls

IC 10

Digital: These catalogs are only available as a PDF.

Information and Download Center
Digital versions of the catalogs are available on the Internet at:
www.siemens.com/lowvoltage/infomaterial

 Siemens AG 2016

Get more information

Security information

siemens.com/lowvoltage

Siemens provides products and solutions with industrial

security functions that support the secure operation of
plants, systems, machines and networks.

Siemens AG
Energy Management
Low Voltage & Products
Postfach 10 09 53
93009 Regensburg
Germany

Siemens AG 2016
Subject to change without prior notice
Article No. E86060-K1814-A101-A3-7600
W-FPN7Z-EM-LPK04 / Dispo 18301
KG 1016 1. AUM 88 En
Printed in Germany

The information provided in this catalog contains merely general

descriptions or characteristics of performance which in case of actual
use do not always apply as described or which may change as a result
of further development of the products. An obligation to provide the
respective characteristics shall only exist if expressly agreed in the
terms of contract. Availability and technical specifications are subject
to change without notice.
All product designations may be trademarks or product names
of Siemens AG or supplier companies whose use by third parties
for their own purposes could violate the rights of the owners.
Token fee: 2.00

In order to protect plants, systems, machines and networks

against cyber threats, it is necessary to implement and
continuously maintain a holistic, state-of-the-art industrial security concept. Siemens products and solutions only
form one element of such a concept.
Customer is responsible to prevent unauthorized access to
its plants, systems, machines and networks. Systems,
machines and components should only be connected to the
enterprise network or the internet if and to the extent
necessary and with appropriate security measures (e.g. use
of firewalls and network segmentation) in place.
Additionally, Siemens guidance on appropriate security
measures should be taken into account. For more information about industrial security, please visit
http://www.siemens.com/industrialsecurity.
Siemens products and solutions undergo continuous
development to make them more secure. Siemens strongly
recommends to apply product updates as soon as available
and to always use the latest product versions. Use of
product versions that are no longer supported, and failure
to apply latest updates may increase customers exposure
to cyber threats.
To stay informed about product updates, subscribe to the
Siemens Industrial Security RSS Feed under
http://www.siemens.com/industrialsecurity.