Scribd
Upload
218 views

EC1204B - Electronic Welding Assembly Tutorials

This document provides a 10 step tutorial for welding an electronic assembly. Key steps include welding SMD components in stages, installing a 32.768KHz crystal oscillator and cutting excess pins, soldering 60 LED lights and a digital tube while ensuring proper orientation, and finishing by installing the microcontroller, clock chip, and battery while paying attention to directionality. Special notes warn that steps 5 and 7 cannot be welded or assembled.

Uploaded by

Mattia Sanchioni
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
218 views

EC1204B - Electronic Welding Assembly Tutorials

This document provides a 10 step tutorial for welding an electronic assembly. Key steps include welding SMD components in stages, installing a 32.768KHz crystal oscillator and cutting excess pins, soldering 60 LED lights and a digital tube while ensuring proper orientation, and finishing by installing the microcontroller, clock chip, and battery while paying attention to directionality. Special notes warn that steps 5 and 7 cannot be welded or assembled.

Uploaded by

Mattia Sanchioni
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 10

EC1204 Pv1.

2
Electronic welding assembly Tutorials
Welding sequence: low to high

Note: Step 5 and Step 7 can not turn, or not assembled welding.

Step 1: Complete SMD components welding; following two charts

PNP TransistorQ1Q6Q7Q8Q9Q10Q11Q12Q13)

10K ResistorR6R12R14R16R18R20R26R29R31R32

R33R34R35

47 ohm ResistorR5R11R13R15R17R19R25R27R30

20pF apacitanceC3C4

104 capacitanceC2C5
PNP TransistorQ2Q3Q4Q5

10K ResistorR1R2R3R4R21

47 ohm ResistorR7R8R9R10

20pF capacitanceC6C7
Step 2: Welding and 32.768KHz 12MHz crystal oscillator, cut excess pin

flat

32.768KHz crystal shown above is recommended for welding, so you can

hold the crystal.


Step 3: torch lights installed, note the location of the + and red light

installation,D5*D10*D15*D20*D25*D30*D35*D40*

D45*D50*D55*D60* are the red lights. after assembling books and

other things to suppress the formation of all the lights, and then rewind

over and solder one pin of a pin, finished weld 60 LED lights will cut all of

its pins
Step 4: Welding sensor DS18B20, cut flat extra pins.

Step5: Welding three buttons RST, MODE, PLUS; 8-pinIC socket U2;40-pin

IC socket U1;battery holder BT1.


Step 6: 8-pin IC cut flat seat and battery holder on extra pins Note: This

step must be, otherwise the back of the LED will not be assembled.

Step 7: Welding at DS1 digital tube, cut flat extra pins, note the direction

of digital tube placement, upside down LED will not be displayed.

Note: The four dots digital control word to be heading EC1204B V1.2

side, as indicated by an arrow

Step 8: Welding 6-pin pin, note: four 6-pin pin pin pad next to the

reserved, no welding.

Step 9:buzzer(SPEAKER),100uFcapacitor-C1,miniUSB-USB; Cut flat extra

pins.

Note: mini USB USB interface is directional and must be assembled as

shown in the following diagram, otherwise it will reverse the positive

and negative power supply system, causing burn chips


Note the direction of welding miniUSB

Step 10: Install AT89S52 microcontroller, DS1302 clock chip, battery, pay

attention to the direction of the chip gap. Following chart shows the

arrow:
front elevation
back elevation

You might also like