Scribd
Upload
98 views

Example 4

This document provides a 3-page calculation sheet summarizing the fatigue strength assessment of a welded hollow section joint in a stainless steel structure. It determines the detail category and partial safety factors. It then calculates the fatigue strength curve and compares the nominal stress ranges to the number of cycles to failure. The cumulative damage is calculated to be 0.78 over the design life, satisfying the design requirement.

Uploaded by

dane05
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
98 views

Example 4

This document provides a 3-page calculation sheet summarizing the fatigue strength assessment of a welded hollow section joint in a stainless steel structure. It determines the detail category and partial safety factors. It then calculates the fatigue strength curve and compares the nominal stress ranges to the number of cycles to failure. The cumulative damage is calculated to be 0.78 over the design life, satisfying the design requirement.

Uploaded by

dane05
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Job No.

R0SU00658 Sheet 1 of 3 Rev B

VTT TECHNICAL RESEARCH Job Title ECSC Stainless Steel Valorisation Project
CENTRE OF FINLAND
VTT BUILDING AND TRANSPORT Subject Design Example 4 Fatigue strength of a welded
Kemistintie 3, Espoo hollow section joint
P.O.Box 1805, FIN02044 VTT, Finland
Telephone: + 358 9 4561
Client Made by AAT Date June 2002
Fax: + 358 9 456 7003
CALCULATION SHEET ECSC Checked by JEK Date June 2002
Revised by MEB Date April 2006

DESIGN EXAMPLE 4 - FATIGUE STRENGTH OF A WELDED HOLLOW SECTION JOINT


This example considers the fatigue strength of the chord of a welded hollow section joint.
Fatigue may be a problem in stainless steel structures, which are subjected to repeated
fluctuations of stresses. Fatigue of welded hollow section joints may be a problem e.g. in
oil platforms, masts, chimneys, bridges, cranes and transport equipment.

EN 1993-1-9:2005 is applicable to stainless steels for estimating the fatigue strength of Section 8
steel structures also. Therefore the section and clause references in this example are to EN
1993-1-9:2005.

The example shows the following design tasks for fatigue assessment:
- determination of the fatigue strength curve
- determination of secondary bending moments in the joint
- determination of the partial safety factor for fatigue strength and
- fatigue assessment for variable amplitude loading.

The chords of the joint are RHS 50x50x4 and braces RHS 30x30x2. The material is
grade 1.4301 stainless steel with 0,2% proof stress of 220 N/mm2.

11
30
x 30 x2
x2 2
x 30
30

50x50x4

Actions
Determined fatigue stress spectra for the chord during the required design life is:
Nominal stress range Number of cycles

1 = 100 N/mm 2 n1 = 10 103


2 = 70 N/mm 2 n2 = 100 103
3 = 40 N/mm 2 n3 = 1000 103

131
Job No. R0SU00658 Sheet 2 of 3 Rev B

VTT TECHNICAL RESEARCH Job Title ECSC Stainless Steel Valorisation Project
CENTRE OF FINLAND
VTT BUILDING AND TRANSPORT Subject Design Example 4 Fatigue strength of a welded
Kemistintie 3, Espoo hollow section joint
P.O.Box 1805, FIN02044 VTT, Finland
Telephone: + 358 9 4561
Client Made by AAT Date June 2002
Fax: + 358 9 456 7003
CALCULATION SHEET ECSC Checked by JEK Date June 2002
Revised by MEB Date April 2006

Structural analysis References


The detail category of the joint depends on the dimensions of chord and braces. In this below are to
example b0 = 50 mm , bi = 30 mm , t 0 = 4 mm and t i = 2 mm . EN 1993-1-
9:2005
Because t 0 / t i = 2 , the detail category is 71. Table 8.7

Because 0,5(b0 bi ) = 10 mm , g = 11 mm , 1,1(b0 bi ) = 22 mm and 2t 0 = 8 mm , the Table 8.7


joint also satisfies the conditions 0,5(b0 bi ) g 1,1(b0 bi ) and g 2t 0 .

Effect of secondary bending moments in the joint


The effects of secondary bending moments are taken into account by multiplying the Clause 4 (2),
stress ranges due to axial member forces by coefficient k1,0 = 1,5 Table 4.1

Partial safety factors


When it is assumed that the structure is damage tolerant and the consequence of failure is Clause 3 (7),
low, the safety factor for fatigue strength is Mf = 1,0 . Table 3.1
Partial safety factor for loading is Ff = 1,0 .

Fatigue assessment
Reference stress range corresponding 2 106 stress fluctuations for detail category 71 is:
c = 71 N/mm2
The fatigue strength curve for lattice girders has a constant slope m = 5 Figure 7.1
The number of stress fluctuations corresponding nominal stress range i is
m
6 c
Ni = 2 10 and
Mf Ff (k1,0 i )
1 = 100 N/mm 2 N1 = 47,5 103
2 = 70 N/mm2 N 2 = 283 103
3 = 40 N/mm2 N 3 = 4640 103

132
Job No. R0SU00658 Sheet 3 of 3 Rev B

VTT TECHNICAL RESEARCH Job Title ECSC Stainless Steel Valorisation Project
CENTRE OF FINLAND
VTT BUILDING AND TRANSPORT Subject Design Example 4 Fatigue strength of a welded
Kemistintie 3, Espoo hollow section joint
P.O.Box 1805, FIN02044 VTT, Finland
Telephone: + 358 9 4561
Client Made by AAT Date June 2002
Fax: + 358 9 456 7003
CALCULATION SHEET ECSC Checked by JEK Date June 2002
Revised by MEB Date April 2006

Palmgren-Miner rule of cumulative damage


Partial damage because of n i cycles of stress range i is
Dd,i = nEi / NEi. Therefore for A.5 (1)
1 = 100 N/mm 2 Dd,1 = 0,21

2 = 70 N/mm 2 Dd,2 = 0,35

3 = 40 N/mm2 Dd,3 = 0,22

n A.5 (1)

n Ei
The cumulative damage during the design life Dd = N Ri
= Dd,i = 0,78
i

Because the cumulative damage is less than unity, the calculated design life of the chord is Clause 8(4)
more than the required design life.

The procedure described above shall also be repeated for the brace.

133
BLANK PAGE

134

You might also like