Hello guys, in the last post I have explained the Basics of Inverters along with its types

and also the inverters topology in other words working of inverters, then we discussed
the Major Components of Inverters. Now in this post I am gonna explain the pure sine
wave inverter and how to create it. I have used AVR microcontroller int his project. The
reason I am using random microcontrollers is that so you guys get a taste of each one.
Before starting on sine wave inverter read this article again and again as I have also
mentioned the problem i got while making it. You should also read the Modified Sine
Wave Design with Code.
I have divided this tutorial into four parts which are shown below. This is a step by step
guide to design and build an inverter and I hope at the end of this tutorial you guys will
be able to design your own inverter. I tried my best to keep it simple but still if you guys
got stuck at any point ask in comments and I will remove your query. This project is
designed by our team and they put real effort in getting this done so thats why we have
placed a small fee on its complete description. You can buy the detailed description of
this project along with the complete code and circuit diagram, by clicking on the below
button:

Buy This Project

Note:

I have also posted a Pure SineWave Inverter Simulation in Proteus, which will be
quite helpful if you are designing a pure sine wave inverter.

PURE SINE-WAVE INVERTER

Pure Sine wave inverter consist of a microcontroller unit which generates a

switching signal of 15 KHz, an H-bridge circuit to convert the signal into AC, a low
pass LC filter circuit to block the high frequency components and the transformer unit
to step-up the voltages.
Block diagram of sine wave circuit is given below:

FIGURE 1 : Block diagram of pure sine wave inverter

AVR MICRO-CONTROLLER UNIT

Microcontroller unit is a multi-purpose control unit which can handle multiple

tasks simultaneously.
We have used it just to generate a switching signal of 15 KHz.
I am using AVR micro-controller unit for this pure sine wave inverter.
Explanation for PWM in AVR
AVR is acting as the brain of Pure Sine Wave Inverter.
 Below is the program for atmega16 microcontroller with a clock frequency of 8
MHz (Fcpu = 8MHz). We have worked on a compiler named AVR GCC.
Initially we included AVR libraries,then we initialized sine table in which the values
of a complete sine wave are stored (we generated a sin table in range 0-359 degrees
whereas, zero of sine wave is set at decimal 128(0x80 in Hex).
Then in the next chunk of the code, we used timer0 (8-bit) which starts from 0
and peaks to 255 (it gives a saw tooth output).
The constant float step = (2*180)/256 = 1.40625 For i=0; s = sin (0*1.40625) = 0
For i = 255 s = sin (255*1.40625) = 358.5937 = 359deg approx.
This is how the sine wave is generated from 0-359deg.
When timer reaches 255 then interrupt over flow is generated (Refer the sine
wave code, at the end).
The next part of the code shows that we have used the clock select bits as pre-
scalar.
TIMSK| = (1<<TOIE0) means we are enabling timer overflow interrupt enable 0.
The last part of the code is the most important part of pure sine wave generator.
OCR0 is output compare register for timer 0 and it continuously compares timer0
values i.e. 0, 1, 2.255, and for each value of timer the value from sine wave table
is computed then sample++increases the pointer of sine wave table to the next i.e.
the value at the second index of sine table and that is computed for the output until
samples equals to 255.
Then we used the command sample = 0 the cycle is repeated again and again.
Heres the programming code for Pure Sine Wave Inverter:
Arduino

1 #include <stdlib.h>
2
3 #include <avr/io.h>
4
5 #include <util/delay.h>
6
7 #include <avr/interrupt.h>
8
9 #include <avr/sleep.h>
10
11 #include <math.h>
12
13 #include <stdio.h>
14
15 0x80, 0x83, 0x86, 0x89, 0x8C, 0x90, 0x93, 0x96,
16
17 0x99, 0x9C, 0x9F, 0xA2, 0xA5, 0xA8, 0xAB, 0xAE,
18
19 0xB1, 0xB3, 0xB6, 0xB9, 0xBC, 0xBF, 0xC1, 0xC4,
20
21 0xC7, 0xC9, 0xCC, 0xCE, 0xD1, 0xD3, 0xD5, 0xD8,
22
23 0xDA, 0xDC, 0xDE, 0xE0, 0xE2, 0xE4, 0xE6, 0xE8,
24
25 0xEA, 0xEB, 0xED, 0xEF, 0xF0, 0xF1, 0xF3, 0xF4,
26
27 0xF5, 0xF6, 0xF8, 0xF9, 0xFA, 0xFA, 0xFB, 0xFC,
28
29 0xFD, 0xFD, 0xFE, 0xFE, 0xFE, 0xFF, 0xFF, 0xFF,
30
31 0xFF, 0xFF, 0xFF, 0xFF, 0xFE, 0xFE, 0xFE, 0xFD,
32
33 0xFD, 0xFC, 0xFB, 0xFA, 0xFA, 0xF9, 0xF8, 0xF6,
34
35 0xF5, 0xF4, 0xF3, 0xF1, 0xF0, 0xEF, 0xED, 0xEB,
36
37 0xEA, 0xE8, 0xE6, 0xE4, 0xE2, 0xE0, 0xDE, 0xDC,
38
39 0xDA, 0xD8, 0xD5, 0xD3, 0xD1, 0xCE, 0xCC, 0xC9,
40
41 0xC7, 0xC4, 0xC1, 0xBF, 0xBC, 0xB9, 0xB6, 0xB3,
42
43 0xB1, 0xAE, 0xAB, 0xA8, 0xA5, 0xA2, 0x9F, 0x9C,
44
45 0x99, 0x96, 0x93, 0x90, 0x8C, 0x89, 0x86, 0x83,
46
47 0x80, 0x7D, 0x7A, 0x77, 0x74, 0x70, 0x6D, 0x6A,
48
49 0x67, 0x64, 0x61, 0x5E, 0x5B, 0x58, 0x55, 0x52,
50
51 0x4F, 0x4D, 0x4A, 0x47, 0x44, 0x41, 0x3F, 0x3C,
52
53 0x39, 0x37, 0x34, 0x32, 0x2F, 0x2D, 0x2B, 0x28,
54
55 0x26, 0x24, 0x22, 0x20, 0x1E, 0x1C, 0x1A, 0x18,
56
57 0x16, 0x15, 0x13, 0x11, 0x10, 0x0F, 0x0D, 0x0C,
58
59 0x0B, 0x0A, 0x08, 0x07, 0x06, 0x06, 0x05, 0x04,
60
61 0x03, 0x03, 0x02, 0x02, 0x02, 0x01, 0x01, 0x01,
62
63 0x01, 0x01, 0x01, 0x01, 0x02, 0x02, 0x02, 0x03,
64
65 0x03, 0x04, 0x05, 0x06, 0x06, 0x07, 0x08, 0x0A,
66
67 0x0B, 0x0C, 0x0D, 0x0F, 0x10, 0x11, 0x13, 0x15,
68
69 0x16, 0x18, 0x1A, 0x1C, 0x1E, 0x20, 0x22, 0x24,
70
71 0x26, 0x28, 0x2B, 0x2D, 0x2F, 0x32, 0x34, 0x37,
72
73 0x39, 0x3C, 0x3F, 0x41, 0x44, 0x47, 0x4A, 0x4D,
74
75 0x4F, 0x52, 0x55, 0x58, 0x5B, 0x5E, 0x61, 0x64,
76
77 0x67, 0x6A, 0x6D, 0x70, 0x74, 0x77, 0x7A, 0x7D
78
79 void InitSinTable()
80
81 {
82
83 Page | 42
84
85 //sin period is 2*Pi
86
87 const float step = (2*M_PI)/(float)256;
88
89 float s;
90
91 float zero = 128.0;
92
93 //in radians
94
95 for(int i=0;i<256;i++)
96
97 {
98
99 s = sin( i * step );
10
0 //calculate OCR value (in range 0-255, timer0 is 8 bit)
10
1 wave[i] = (uint8_t) round(zero + (s*127.0));
10
2 }
10
3 }
10
4 void InitPWM()
10
5 {
10
6 /*
10
7 TCCR0 - Timer Counter Control Register (TIMER0)
10
8 -----------------------------------------------
10
9 BITS DESCRIPTION
11
0 NO: NAME DESCRIPTION
11
1 --------------------------
11
2 BIT 7 : FOC0 Force Output Compare
11
3 BIT 6: WGM00 Wave form generartion mode [SET to 1]
11
4 BIT 5: COM01 Compare Output Mode [SET to 1]
11
5 BIT 4: COM00 Compare Output Mode [SET to 0]
11
6 BIT 3: WGM01 Wave form generation mode [SET to 1]
11
7 BIT 2: CS02 Clock Select [SET to 0]
11
8 BIT 1: CS01 Clock Select [SET to 0]
11
9 BIT 0: CS00 Clock Select [SET to 1]
12
0 Timer Clock = CPU Clock (No Pre-scaling)
12
1 Mode = Fast PWM
12
2 PWM Output = Non Inverted
12
3 */
12
4 TCCR0|=(1<<WGM00)|(1<<WGM01)|(1<<COM01)|(1<<CS00);
12
5 TIMSK|=(1<<TOIE0);
12
6 //Set OC0 PIN as output. It is PB3 on ATmega16 ATmega32
12
7 DDRB|=(1<<PB3);
12
8 }
12
9 ISR(TIMER0_OVF_vect)
13
0 {
13
1 OCR0 = wave[sample];
13
2 sample++;
13
3 if( sample >= 255 )
13
4 sample = 0;
13
5 }
13
6
13
7
13
8
13
9
14
0
14
1
14
2
14
3
14
4
14
5
14
6
14
7
14
8
14
9
15
0
15
1
15
2
15
3
15
4
15
5
15
6
15
7
15
8
15
9
16
0
16
1
16
2
16
3
16
4
16
5
16
6
16
7
16
8
16
9
17
0
17
1

H-BRIDGE CIRCUIT

H-Bridge Circuit is acting as the main core of Pure sine Wave Inverter.
H-bridge circuit is basically enables a voltage to be applied across a load in either
direction.
In inverters, it is used to amplify the input square wave coming from the micro-
controller.
We are giving modulated square wave at the input of the H-bridge because if we
give sine wave to the MOSFET or any other switching device like the BJT or IGBT,
very high switching losses occur. This is because when we give sinusoidal waveform
to any of these devices, they start operating in the linear region, and power loss
occurs in devices operating in linear region.
When we give a square waveform to them, they operate on either saturation or
cut-off regions thus having minimum power loss.
We used IRF5305 and IRFP150 MOSFETs. These are high power MOSFETs
with maximum current rating of 31 Amp and 42 Amp respectively.
IFR5305 is a Pchannel MOSFET whereas IRFP150 is an N-channel MOSFET.
The circuit configuration of H-bridge is given below:
 FIGURE 2 : H-Bridge Circuit

Working
Working of an H-bridge for pure sine wave inverter can be divided into two
modes.
In Mode1, the input signal at the gate of M1 is high and at the gate of M4 it is
low.This causes conduction from M1-M4 and we achieve a +12V signal at the output.
In Mode2, the input signal at the gate of M3 is high and at the gate of M2 it is
low.This causes conduction from M3-M2 and we achieve a -12V signal at the output.
And thus we obtain a 24Vpeak-peak signal at the output.
The working of H-Bridge in both conduction modes can be easily understood by
the following figure:
 FIGURE 3 : H-Bridge Conduction Modes (A)

FIGURE 3 : H-Bridge Conduction Modes (B)

Due to the conduction of half part of the bridge at +ve half cycle and the other half
part of the bridge at ve half cycle, we obtain a square waveform of 24 Vpeak-peak at
the output.
In figure below is the Proteus simulation showing the waveform output of bridge
circuit during each conduction cycle.
 FIGURE 4 : Wave-forms of H-bridge conduction cycle

Observations
In the H-bridge circuit we have observed that input signal s frequency does not
change at the output that means the frequency remains un-altered.
Only the power of the signal increase in terms of current.
Problems
Initially we used all the MOSFETs of same type (i-e. n-channel MOSFETs). This
caused the shorting of the MOSFETs during the conduction mode. This phenomenon
is known as shooting over of the MOSFET.
Despite the duration of this shooting over was quite small, it caused loading on
the MOSFETs.
The MOSFETs started heating up due to this, and eventually they burned out.
Another problem occurred while using the MOSFETs of same channel was that
the upper MOSFETs (M1 and M3) did not turn on properly.
After studying, we learned that they required 18V to turn on thus; we needed a
MOSFET driver that was IR2110.
We worked on it but it did not working properly too, because according to the
formula for bootstrap capacitor given in datasheet, the driver must have given 18V
output but it was not working so we had to search for an alternate.
 Then after extended study we came to know that replacing the upper two n
channel MOSFETs with p channel MOSFET is the solution. We applied this technique
and it worked.
Using this technique also solved the problem of MOSFET shooting over by
inducing a dead time/delay in the MOSFET switching.
LC FILTER

We have determined inductance of the inductor using LC resonant band stop

filter as LC meters were not available in the lab.

FIGURE 5 : LC filter

Working
Understanding the working of H-Bridge is very essential, if you want to work on
Pure sine Wave Inverter.
The method to determine L or C is simple. Suppose we are required to determine
the inductance, then by above circuit,

V1 signal from function generator is set to 1Vrms using multi-meter.

At resonance frequency the LC combination will have very low impedance so it
will short out the signal and will drop across resistor R1 and prevents the signal to
reach the load.
 Using this principle we have varied signal frequency from function generator and
we are detecting output voltage at load using multi-meter.
At resonance frequency multi-meter will show ideally zero volts.
So by using formula we have :

Problems
First we designed an RC circuit but we observed that the Resistance R in the
circuit acts as a load and dissipates power.
After studying, we decided to use an LC filter.
The main problem with the LC filter was the designing of the inductor as the
inductor of desired value was not available in the market, thus we had to make it by
hand.
LC meter was not available also thus we had to repeatedly calculate the
inductance value mathematically.
WORKING OF PURE SINE WAVE INVERTER

Lets have a look at the working of Pure Sine Wave Inverter.

A 50Hz sin wave is generated with the help of a lookup table within the AVR
microcontroller and is modulated over a switching frequency signal of 15KHz.
As this signal has very weak current, so it is amplified by a BC 547 transistor.
The amplified signal is given at the gates of M1 and M2 MOSFETs.
The output of the microcontroller is given to another BC 547 which is working as
an inverting amplifier.
By this, the signal from the microcontroller gets inverted as well as amplified.
This signal is given at the gates of M3 and M4 MOSFETs.
Now what happens is that, when the input signal at the gate of M1 of the H-bridge
is high and at the gate of M4 of the H-bridge is low, conduction from M1-M4 occurs
and we achieve a +12V signal.
When the input signal at the gate of M3 goes high and at the gate of M2 goes
low, conduction from M3-M2 occurs and we achieve a -12V signal.
Thus at the output we receive a waveform of 12Vpeak or 24Vpeak-peak.
The output of the H-bridge is then fed into a low pass LC filter which filters the
high frequency components of 15 KHz and gives the 50 Hz sine output.
This output is then fed into a transformer which steps up this 12 Volts AC
waveform into 220Volts AC.
So, thats all for today. I hope you guys have enjoyed this Pure Sine Wave Inverter
Project. You should also look at Proteus simulation of Pure sine wave, because
simulations help a lot in designing hardware projects. So, take care and have fun !!!