Power Systems
Finding parts, locations, and addresses



Power Systems
Finding parts, locations, and addresses
 Note
Before using this information and the product it supports, read the information in Notices, on
page 235, Safety notices on page v, the IBM Systems Safety Notices manual, G229-9054, and the
IBM Environmental Notices and User Guide, Z1255823.

This edition applies to IBM Power Systems servers that contain the POWER6 processor and to all associated
models.
Copyright IBM Corporation 2007, 2012.
US Government Users Restricted Rights Use, duplication or disclosure restricted by GSA ADP Schedule Contract
with IBM Corp.
Contents
Safety notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

Finding parts, locations, and addresses . . . . . . . . . . . . . . . . . . . . . . 1

Part locations and location codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
8203-E4A, 8261-E4S, 9407-M15, 9408-M25 . . . . . . . . . . . . . . . . . . . . . . . . . 2
Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
8204-E8A and 9409-M50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
8234-EMA, 9117-MMA, and 9406-MMA . . . . . . . . . . . . . . . . . . . . . . . . . 25
Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
9119-FHA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
9125-F2A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
0595, 5095, and 7311-D20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
5094, 5294, 5096, and 5296 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
5786, 5787, 7031-D24, and 7031-T24 . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
5790 and 7311-D11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
5791, 5794, 5797, and 5798 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
5796 and 7314-G30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
5802 and 5877 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
5803 and 5873 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
5886 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
8203-E4A, 8261-E4S, 9407-M15, and 9408-M25 addresses . . . . . . . . . . . . . . . . . . . 118
8204-E8A and 9409-M50 addresses . . . . . . . . . . . . . . . . . . . . . . . . . . 119
8234-EMA, 9117-MMA, and 9406-MMA addresses . . . . . . . . . . . . . . . . . . . . . 120
0595, 5095, and 7311-D20 addresses . . . . . . . . . . . . . . . . . . . . . . . . . . 122
5094, 5294, 5096, and 5296 addresses . . . . . . . . . . . . . . . . . . . . . . . . . 124
5786, 5787, 7031-D24, and 7031-T24 addresses . . . . . . . . . . . . . . . . . . . . . . 130
5790 and 7311-D11 addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
5796 and 7314-G30 addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
5802 and 5877 addresses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
5803 and 5873 addresses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
5886 addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
System parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
8203-E4A, 8261-E4S, 9407-M15, and 9408-M25 system parts . . . . . . . . . . . . . . . . . . 136
8204-E8A and 9409-M50 system parts . . . . . . . . . . . . . . . . . . . . . . . . . 145
8234-EMA, 9117-MMA, and 9406-MMA . . . . . . . . . . . . . . . . . . . . . . . . 157
9119-FHA system parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
9125-F2A system parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
0595, 5095, and 7311-D20 system parts . . . . . . . . . . . . . . . . . . . . . . . . . 190
5094, 5294, 5096, and 5296 system parts . . . . . . . . . . . . . . . . . . . . . . . . 200
5786, 5787, 7031-D24, and 7031-T24 system parts . . . . . . . . . . . . . . . . . . . . . 212
5790 and 7311-D11 system parts . . . . . . . . . . . . . . . . . . . . . . . . . . . 216
5791, 5794, 5797, and 5798 system parts . . . . . . . . . . . . . . . . . . . . . . . . 222

Copyright IBM Corp. 2007, 2012 iii

 5796 and 7314-G30 system parts . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
5802 and 5877 system parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227
5803 and 5873 system parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230
5886 system parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232

Appendix. Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235

Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236
Electronic emission notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236
Class A Notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236
Terms and conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240

iv Finding parts, locations, and addresses

Safety notices
Safety notices may be printed throughout this guide:
v DANGER notices call attention to a situation that is potentially lethal or extremely hazardous to
people.
v CAUTION notices call attention to a situation that is potentially hazardous to people because of some
existing condition.
v Attention notices call attention to the possibility of damage to a program, device, system, or data.

World Trade safety information

Several countries require the safety information contained in product publications to be presented in their
national languages. If this requirement applies to your country, a safety information booklet is included
in the publications package shipped with the product. The booklet contains the safety information in
your national language with references to the U.S. English source. Before using a U.S. English publication
to install, operate, or service this product, you must first become familiar with the related safety
information in the booklet. You should also refer to the booklet any time you do not clearly understand
any safety information in the U.S. English publications.

German safety information

Das Produkt ist nicht fr den Einsatz an Bildschirmarbeitspltzen im Sinne 2 der

Bildschirmarbeitsverordnung geeignet.

Laser safety information

IBM servers can use I/O cards or features that are fiber-optic based and that utilize lasers or LEDs.

Laser compliance

All lasers are certified in the U.S. to conform to the requirements of DHHS 21 CFR Subchapter J for class
1 laser products. Outside the U.S., they are certified to be in compliance with IEC 60825 as a class 1 laser
product. Consult the label on each part for laser certification numbers and approval information.

CAUTION:
This product might contain one or more of the following devices: CD-ROM drive, DVD-ROM drive,
DVD-RAM drive, or laser module, which are Class 1 laser products. Note the following information:
v Do not remove the covers. Removing the covers of the laser product could result in exposure to
hazardous laser radiation. There are no serviceable parts inside the device.
v Use of the controls or adjustments or performance of procedures other than those specified herein
might result in hazardous radiation exposure.
(C026)

CAUTION:
Data processing environments can contain equipment transmitting on system links with laser modules
that operate at greater than Class 1 power levels. For this reason, never look into the end of an optical
fiber cable or open receptacle. (C027)

CAUTION:
This product contains a Class 1M laser. Do not view directly with optical instruments. (C028)

Copyright IBM Corp. 2007, 2012 v

CAUTION:
Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following
information: laser radiation when open. Do not stare into the beam, do not view directly with optical
instruments, and avoid direct exposure to the beam. (C030)

Power and cabling information for NEBS (Network Equipment-Building System)

GR-1089-CORE

The following comments apply to the IBM servers that have been designated as conforming to NEBS
(Network Equipment-Building System) GR-1089-CORE:

The equipment is suitable for installation in the following:

v Network telecommunications facilities
v Locations where the NEC (National Electrical Code) applies

The intrabuilding ports of this equipment are suitable for connection to intrabuilding or unexposed
wiring or cabling only. The intrabuilding ports of this equipment must not be metallically connected to the
interfaces that connect to the OSP (outside plant) or its wiring. These interfaces are designed for use as
intrabuilding interfaces only (Type 2 or Type 4 ports as described in GR-1089-CORE) and require isolation
from the exposed OSP cabling. The addition of primary protectors is not sufficient protection to connect
these interfaces metallically to OSP wiring.

Note: All Ethernet cables must be shielded and grounded at both ends.

The ac-powered system does not require the use of an external surge protection device (SPD).

The dc-powered system employs an isolated DC return (DC-I) design. The DC battery return terminal
shall not be connected to the chassis or frame ground.

vi Finding parts, locations, and addresses

Finding parts, locations, and addresses
Locate physical part locations and identify parts with system diagrams.

You can identify the enclosure in which a field replaceable unit (FRU) is plugged by its location code. The
first character of the location code is always U followed by a 4character feature code or enclosure type
as shown in the following example: U789C.001.10ABCDE-P3-C31 In this example, the enclosure type is
789C.

The next 3 characters of the location code indicate the model of the enclosure (001 in the example). The
next string of characters provides the enclosure serial number (10ABCDE in the example).

Using this information, locate the enclosure with the FRU you want to replace. Find the enclosure type in
the following table and go to the service information for that enclosure.

Feature code (Utttt) System

U789D.001 9117-MMA
U9406.MMA 9406-MMA
U8234.EMA 8234-EMA
U789C.001 8203-E4A
U9407.M15 9407-M15
U9408.M25 9408-M25
U78A0.001 8204-E8A
U9409.M50 9409-M50
U9125.F2A 9125-F2A
U9119.FHA 9119-FHA
U7311.D11 7311-D11
U5790.001 5790
U7314.G30 7314-G30
U5796.001 5796
U7311.D20 7311-D20
U0595.001 0595
U5095.001 5095
U5094.001 5094
U5294.001 5294
U5096.001 5096
U5296.001 5296
U7031.T24 7031-T24
U5786.001 5786
U5787.001 5787
U7031.D24 7031-D24
U7311.D10 7311-D10
U5796.001 5796

Copyright IBM Corp. 2007, 2012 1

Feature code (Utttt) System
U5886.001 5886
U5791.001 5791
U5802.001 5802
U5877.001 5877
U5803.001 5803
U5873.001 5873

Locate the FRU

The string of characters following the enclosure serial number identifies the FRU location within the
enclosure: U7879.001.10ABCDE-P3-C31 In this example, P3-C31 is the location of the FRU to be replaced.
Use the graphics and tables to locate the FRU and link to its removal and replacement procedure.

Part locations and location codes

You can find part locations by using location codes. Illustrations are provided to help you map a location
code to a position on the server or expansion unit.

8203-E4A, 8261-E4S, 9407-M15, 9408-M25

The information provided in this topic defines specific sections of a location code string. Use this
information to understand the meaning of a location code.

Using location codes

Use the following table to link to a specific topic that you need additional information on when reading
your location code.

Location code topics that might be of interest Description

Location code overview on page 3 Contains background information on the use of location
codes.
Physical location codes on page 3 Provides a definition for physical location code.
Logical location codes on page 3 Provides a definition of what a logical location code is.
Location code format on page 3 Provides descriptive information of the Un value in the
location code string. For example U789C.001.
Location code labels on page 4 Provides a table that identifies and defines the location
code labels. The location code labels begin with an
alphabetic character and follow the system serial number.
For example, U789C.001.10ABCDE-P3-C31-T2-L23. (The
system serial number is the 10ABCDE in the previous
example.) The P3, C31, T2, and L23 all contain an
alphabetic character that is identified in the Location
code labels table.
Worldwide unique identifier on page 5 Provides a definition for the world unique identifier. This
group of digits follows the resource code labels and
always begins with the letter W.

2 Finding parts, locations, and addresses

Location code overview

Servers (system unit and expansion units) use physical location codes to provide mapping of replaceable
units. Location codes are produced by the server's firmware, which structures them so that they can be
used to identify specific parts in a system. The location code format is the same for all servers.

If you are working with a specific location code, the unit type and model immediately follow the first
character (Utttt.mmm). Match the unit type and model to a link, as shown in the Unit type and locations
table.

If the location code ends with -Txx-Lxx, the server's firmware could not identify the physical location.
When a physical location cannot be identified, a logical location code is provided. Where logical location
codes occur in enclosures, the locations topic for the enclosure has the known conversions listed. For
logical location codes with no conversion, contact your next level of support.

If the location code begins with UTMPx, the expansion I/O unit's machine type, model and serial
number have not been set yet and this is a temporary unit identifier. To identify the unit, examine the
display panels on all of the expansion I/O units connected to the server until you find one with the same
characters in the first 5 digits of the top line in the unit's display. Record the unit's real machine type and
model from the unit label. Match the unit's machine type and model in the Unit type and locations table
and follow the link to determine the service information.

Note: Locations for units that are not in the preceding list are either not supported or there is a problem
in the firmware. Contact your next level of support.

Physical location codes

Physical location codes provide a mapping of logical functions and components (such as backplanes,
removable modules, connectors, ports, cables, and devices) to their specific locations within the physical
structure of the server.

Logical location codes

If the physical location cannot be mapped to a physical location code, the server's firmware generates a
logical location code. A logical location code is a sequence of location labels that identifies the path that
the system uses to communicate with a given resource.

Note: A resource has as many logical location codes as it has logical connections to the system. For
example, an external tape device connected to two I/O adapters will have two logical location codes.

An example of a logical location code is:

U789C.001.10ABCDE-P3-C31-T2-L23

The first part of the location code (through the T2 label) represents the physical location code for the
resource that communicates with the target resource. The remainder of the logical location code (L23)
represents exactly which resource is indicated.

Location code format

The location code is an alphanumeric string of variable length, consisting of a series of location
identifiers, separated by a dash. An example of a physical location for a fan is Un-A1.

The first position, represented by Un (where n is equal to any string contained between the U and the
hyphen) in the preceding example, is displayed in one of the forms in the following table.

Finding parts, locations, and addresses 3

Note: In location codes the U is a constant digit; however, the numbered positions that follow the U are
variables and are dependent on your server. Each column defines the numbers that follow the U in the
beginning of the location code.

Machine type and model number in its location codes Feature codes and sequence numbers in its location
code

Utttt.mmm.sssssss-A1 Uffff.ccc.sssssss-A1
The leftmost code is always U. The leftmost code is always U.
tttt represents the unit type of the enclosure (drawer or ffff represents the feature code of the enclosure (drawer
node). or node).
mmm represents the model of the enclosure. ccc represents the sequence number of the enclosure .
sssssss represents the serial number for the enclosure. sssssss represents the serial number of the enclosure.
Note: The mmm or ccc number might not be displayed on all location codes for all servers. If the mmm value is not
displayed, the location code is displayed in one of the following forms:
v Utttt.sssssss-A1
v Uffff.sssssss-A1

The location code is hierarchical; that is, each location identifier in the string represents a physical part.
The order (from left to right), in which each identifier is shown, allows you to determine which parts
contain other parts in the string.

The dash (-) separator character represents a relationship between two components in the unit. In the
example of the fan, whose location code is Un-A1, the dash shows that the fan (A1) is contained in the
base unit (or Un). Modules, adapters, cables, and devices are all parts that are plugged into another part.
Their location codes will always show that they are plugged into another part as components of the
server. Another example follows:, Un-P1-C9 is a memory DIMM, with memory DIMM (C9) plugged into
a backplane (P1), which is inside the unit (Un).

For more information about the various location code label prefixes, refer to Location code labels.

Note: For devices, certain error conditions might cause an IBM i device to display the device location in
an AIX format.
Table 1. Unit type and locations
Unit type (Utttt.mmm) Link to location information
U789C.001 8203.E4A Locations
U9407.M15 9407.M15 Locations
U9408.M25 9408.M25 Locations

Location code labels

The following table describes the location code label prefixes.

Note: These labels apply to system units only.

Table 2. Location code label prefixes for system units
Prefix Description Example
A Air-moving device Fan, blower
C Card connector IOP, IOA, DIMM, processor card
D Device Diskette, control panel

4 Finding parts, locations, and addresses

Table 2. Location code label prefixes for system units (continued)
Prefix Description Example
E Electrical Battery, power supply, ac charger
L Logical path SAS target IDE address, fibre channel LUN
N Horizontal placement for an empty rack location
P Planar System backplane
T Port, external cable
U Unit
V Virtual planar
W Worldwide unique ID
X EIA value for an empty rack location
Y Firmware FRU

Worldwide unique identifier

A worldwide unique identifier location label consists of the prefix W followed by a maximum of 16
uppercase hexadecimal digits with no leading zeros. A location code might not consist of a worldwide
unique identifier. When present, the worldwide unique identifier location label follows the location label
of the resource that interfaces with the resource that has the worldwide unique identifier, usually a port.

Locations
Use this information to help you map a location code to a position on the unit.

The following diagrams show field replaceable unit (FRU) layouts in the system. Use these diagrams with
the following tables.

Rack views

Finding parts, locations, and addresses 5

Figure 1. Rack front view with 3.5 inch DASD

Figure 2. Rack front view with 2.5 inch DASD

6 Finding parts, locations, and addresses

Figure 3. Rack top view, without fans

Figure 4. Rack top view, with fans

Finding parts, locations, and addresses 7

Figure 5. Rack rear view

Stand-alone views

Figure 6. Stand-alone front view with 3.5 inch DASD

8 Finding parts, locations, and addresses

Figure 7. Stand-alone front view with 2.5 inch DASD

Figure 8. Stand-alone side view without fans

Finding parts, locations, and addresses 9

Figure 9. Stand-alone side view with fans

Figure 10. Stand-alone rear view

The following table provides location codes for parts that comprise the server.

10 Finding parts, locations, and addresses

Table 3. FRU location table
Failing item name Physical location code Identify LED
System unit Un
Fans
Fan 1 Un-A1 Yes
Fan 2 Un-A2 Yes
Fan 3 Un-A3 Yes
Fan 4 Un-A4 Yes
Power supplies
Power supply 1 Un-E1 Yes
Power supply 2 Un-E2 Yes
Backplanes
Input/output backplane with embedded: Un-P1 Yes
v RIO Hub/HSL NIC
v RIO/HSL link
v Ethernet controller
v USB controller (AIX or Linux environment
only)
v SAS controllers
v Logic oscillator
v Service processor
v Processor 1
v Processor 2
v SPCN
v Time-of-day
Time-of-day battery Un-P1-E1
DASD and media backplane Un-P2 Yes
DVD Un-P2-D2
System backplane cables
System serial cable 1 (top connector) Un-P1-T3
System serial cable 2 (bottom connector) Un-P1-T4
Embedded USB front cable Un-D1-T1
Embedded USB rear cable 1 Un-P1-T7
Embedded USB rear cable 2 Un-P1-T8
SPCN cable 1 (top connector) Un-P1-T1
SPCN cable 2 (bottom connector) Un-P1-T2
HMC 1 (left connector) Un-P1-T5
HMC 2 (right connector) Un-P1-T6
Dual 1 GB Ethernet cable 1 Un-P1-C7-T1
Dual 1 GB Ethernet cable 2 Un-P1-C7-T2
Quad 1 GB Ethernet port 1 Un-P1-C7-T1
Quad 1 GB Ethernet cable 2 Un-P1-C7-T2
Quad 1 GB Ethernet cable 3 Un-P1-C7-T3

Finding parts, locations, and addresses 11

Table 3. FRU location table (continued)
Failing item name Physical location code Identify LED
Quad 1 GB Ethernet cable 4 Un-P1-C7-T4
External SAS cable Un-P2-T1
Internal SAS cable Un-P1-T9
Processor and processor regulator
Voltage regulator 1A for processor 1 Un-P1-C13 Yes
Voltage regulator 1B for processor 1 Un-P1-C13 Yes
Voltage regulator 2 for processor 1 Un-P1-C18 Yes
Voltage regulator 1A for processor 2 Un-P1-C19 Yes
Voltage regulator 1B for processor 2 Un-P1-C19 Yes
Voltage regulator 2 for processor 2 Un-P1-C20 Yes
VPD card Un-P1-C11 Yes
Adapters
PCI-E adapter in slot 1 Un-P1-C1 Yes
PCI-E adapter in slot 2 Un-P1-C2 Yes
PCI-E adapter in slot 3 Un-P1-C3 Yes
PCI-X adapter in slot 4 Un-P1-C4 Yes
PCI-X adapter in slot 5 Un-P1-C5 Yes
Ethernet card Un-P1-C7 Yes
RIO/HSL/GX Dual-Port 12X Channel Attach Un-P1-C8 Yes
adapter controller slot 1
RIO/HSL/GX Dual-Port 12X Channel Attach Un-P1-C6 Yes
adapter controller slot 2
RIO/HSL/GX Dual-Port 12X Channel Attach Un-P1-C8-T1 Yes, for RIO adapter
adapter controller slot 1 port 1 controller

No, for 12X Channel

Attach adapter
RIO/HSL/GX Dual-Port 12X Channel Attach Un-P1-C8-T2 Yes, for RIO adapter
adapter controller slot 1 port 2 controller

No, for 12X Channel

Attach adapter
RIO/HSL/GX Dual-Port 12X Channel Attach Un-P1-C6-T1 Yes, for RIO adapter
adapter controller slot 2 port 1 controller

No, for 12X Channel

Attach adapter
RIO/HSL/GX Dual-Port 12X Channel Attach Un-P1-C6-T2 Yes, for RIO adapter
adapter controller slot 2 port 2 controller

No, for 12X Channel

Attach adapter
Auxiliary cache card for system backplane Un-P1-C9 Yes
Auxiliary cache card battery Un-P1-C9-E1 No
RAID enablement card for system backplane Un-P1-C10 Yes
Thermal management card Un-P1-C12 Yes

12 Finding parts, locations, and addresses

Table 3. FRU location table (continued)
Failing item name Physical location code Identify LED
Memory modules
Memory module 1 Un-P1-C14 Yes
Memory module 2 Un-P1-C15 Yes
Memory module 3 Un-P1-C16 Yes
Memory module 4 Un-P1-C17 Yes
Memory module 5 Un-P1-C21 Yes
Memory module 6 Un-P1-C22 Yes
Memory module 7 Un-P1-C23 Yes
Memory module 8 Un-P1-C24 Yes
Device physical locations
Removable media Un-P2-D1 No
Removable media Un-P2-D2 No
Disk drive 1 Un-P2-D3 Yes
Disk drive 2 Un-P2-D4 Yes
Disk drive 3 Un-P2-D5 Yes
Disk drive 4 Un-P2-D6 Yes
Disk drive 5 Un-P2-D7 Yes
Disk drive 6 Un-P2-D8 Yes
Disk drive 7 Un-P2-D9 Yes
Disk drive 8 Un-P2-D10 Yes
Control panel
Control panel Un -D1
Temperature sensor Un -D1
Server firmware
Server firmware Un-Y1

8204-E8A and 9409-M50

The information provided in this topic defines specific sections of a location code string. Use this
information to understand the meaning of a location code.

Using location codes

Use the following table to link to a specific topic that you need additional information on when reading
your location code.

Location code topics that might be of interest Description

Location code overview on page 14 Contains background information on the use of location
codes.
Physical location codes on page 14 Provides a definition for physical location code.
Logical location codes on page 14 Provides a definition of what a logical location code is.
Location code format on page 15 Provides descriptive information of the Un value in the
location code string. For example U78A0.001.

Finding parts, locations, and addresses 13

Location code topics that might be of interest Description
Location code labels on page 16 Provides a table that identifies and defines the location
code labels. The location code labels begin with an
alphabetic character and follow the system serial number.
For example, U78A0.001.10ABCDE-P3-C31-T2-L23. (The
system serial number is the 10ABCDE in the previous
example.) The P3, C31, T2, and L23 all contain an
alphabetic character that is identified in the Location
code labels table.
Worldwide unique identifier on page 16 Provides a definition for the world unique identifier. This
group of digits follows the resource code labels and
always begins with the letter W.

Location code overview

Servers (system unit and expansion units) use physical location codes to provide mapping of replaceable
units. Location codes are produced by the server's firmware, which structures them so that they can be
used to identify specific parts in a system. The location code format is the same for all servers.

If you are working with a specific location code, the unit type and model immediately follow the first
character (Utttt.mmm). Match the unit type and model to a link, as shown in the Unit type and locations
table.

If the location code ends with -Txx-Lxx, the server's firmware could not identify the physical location.
When a physical location cannot be identified, a logical location code is provided. Where logical location
codes occur in enclosures, the locations topic for the enclosure has the known conversions listed. For
logical location codes with no conversion, contact your next level of support.

If the location code begins with UTMPx, the expansion I/O unit's machine type, model and serial
number have not been set yet and this is a temporary unit identifier. To identify the unit, examine the
display panels on all of the expansion I/O units connected to the server until you find one with the same
characters in the first 5 digits of the top line in the unit's display. Record the unit's real machine type and
model from the unit label. Match the unit's machine type and model in the Unit type and locations table
and follow the link to determine the service information.

Note: Locations for units that are not in the preceding list are either not supported or there is a problem
in the firmware. Contact your next level of support.

Physical location codes

Physical location codes provide a mapping of logical functions and components (such as backplanes,
removable modules, connectors, ports, cables, and devices) to their specific locations within the physical
structure of the server.

Logical location codes

If the physical location cannot be mapped to a physical location code, the server's firmware generates a
logical location code. A logical location code is a sequence of location labels that identifies the path that
the system uses to communicate with a given resource.

Note: A resource has as many logical location codes as it has logical connections to the system. For
example, an external tape device connected to two I/O adapters will have two logical location codes.

An example of a logical location code is:

U7879.001.10ABCDE-P3-C31-T2-L23

14 Finding parts, locations, and addresses

The first part of the location code (through the T2 label) represents the physical location code for the
resource that communicates with the target resource. The remainder of the logical location code (L23)
represents exactly which resource is indicated.

Location code format

The location code is an alphanumeric string of variable length, consisting of a series of location
identifiers, separated by a dash. An example of a physical location for a fan is Un-A1.

The first position, represented by Un (where n is equal to any string contained between the U and the
hyphen) in the preceding example, is displayed in one of the forms in the following table.

Note: In location codes the U is a constant digit; however, the numbered positions that follow the U are
variables and are dependent on your server. Each column defines the numbers that follow the U in the
beginning of the location code.

Machine type and model number in its location codes Feature codes and sequence numbers in its location
code

Utttt.mmm.sssssss-A1 Uffff.ccc.sssssss-A1
The leftmost code is always U. The leftmost code is always U.
tttt represents the unit type of the enclosure (drawer or ffff represents the feature code of the enclosure (drawer
node). or node).
mmm represents the model of the enclosure. ccc represents the sequence number of the enclosure .
sssssss represents the serial number for the enclosure. sssssss represents the serial number of the enclosure.
Note: The mmm or ccc number might not be displayed on all location codes for all servers. If the mmm value is not
displayed, the location code is displayed in one of the following forms:
v Utttt.sssssss-A1
v Uffff.sssssss-A1

The location code is hierarchical; that is, each location identifier in the string represents a physical part.
The order (from left to right), in which each identifier is shown, allows you to determine which parts
contain other parts in the string.

The dash (-) separator character represents a relationship between two components in the unit. In the
example of the fan, whose location code is Un-A1, the dash shows that the fan (A1) is contained in the
base unit (or Un). Modules, adapters, cables, and devices are all parts that are plugged into another part.
Their location codes will always show that they are plugged into another part as components of the
server. Another example follows:, Un-P1-C9 is a memory DIMM, with memory DIMM (C9) plugged into
a backplane (P1), which is inside the unit (Un).

For more information about the various location code label prefixes, refer to Location code labels.

Note: For devices, certain error conditions might cause an IBM i device to display the device location in
an AIX format.
Table 4. Unit type and locations
Unit type (Utttt) Link to location information
U78A0.001 8204.E8A Locations
U9409.M50 9409.M50 Locations

Finding parts, locations, and addresses 15

Location code labels

The following table describes the location code label prefixes.

Note: These labels apply to system units only.

Table 5. Location code label prefixes for system units
Prefix Description Example
A Air-moving device Fan, blower
C Card connector IOP, IOA, DIMM, processor card
D Device Diskette, control panel
E Electrical Battery, power supply, ac charger
L Logical path SAS target IDE address, fibre channel LUN
N Horizontal placement for an empty rack location
P Planar System backplane
T Port, external cables
U Unit
V Virtual planar
W Worldwide unique ID
X EIA value for an empty rack location
Y Firmware FRU

Worldwide unique identifier

A worldwide unique identifier location label consists of the prefix W followed by a maximum of 16
uppercase hexadecimal digits with no leading zeros. A location code might not consist of a worldwide
unique identifier. When present, the worldwide unique identifier location label follows the location label
of the resource that interfaces with the resource that has the worldwide unique identifier, usually a port.

Locations
Use this information to help you map a location code to a position on the unit.

The following diagrams show field replaceable unit (FRU) layouts in the system. Use these diagrams with
the following tables.

Rack views

16 Finding parts, locations, and addresses

Figure 11. Rack front view with 3.5 inch DASD

Figure 12. Rack front view with 2.5 inch DASD

Finding parts, locations, and addresses 17

Figure 13. Rack top view

Figure 14. Rack rear view

Stand-alone views

18 Finding parts, locations, and addresses

Figure 15. Stand-alone front view with 3.5 inch DASD

Figure 16. Stand-alone front view with 2.5 inch DASD

Finding parts, locations, and addresses 19

Figure 17. Stand-alone side view

Figure 18. Stand-alone rear view

Processor book

20 Finding parts, locations, and addresses

Figure 19. Rack and stand-alone processor book

Location codes

The following table provides location codes for parts that comprise the server.
Table 6. FRU location table
Failing item name Physical location code Identify LED
System unit Un
Fans
Fan 1 Un-A1 Yes
Fan 2 Un-A2 Yes
Fan 3 Un-A3 Yes
Fan 4 Un-A4 Yes
Power supplies
Power supply 1 Un-E1 Yes
Power supply 2 Un-E2 Yes
Backplanes

Finding parts, locations, and addresses 21

Table 6. FRU location table (continued)
Failing item name Physical location code Identify LED
Input/output backplane with embedded: Un-P1 Yes
v RIO Hub/HSL NIC
v RIO/HSL link
v Ethernet controller
v USB controller (AIX or Linux only)
v SAS controllers
v Logic oscillator
v Service processor
v SPCN
v Time-of-day
Battery Un-P1-E1
DASD and media backplane Un-P2 Yes
DVD Un-P2-D2
System backplane ports
System serial port 1 (rear view - left connector) Un-P1-T1
System serial port 2 (rear view - right connector) Un-P1-T2
Embedded USB front port Un-D1-T1
Embedded USB rear port 1 Un-P1-T3
Embedded USB rear port 2 Un-P1-T4
SPCN port 1 (rear view - left connector) Un-P1-T5
SPCN port 2 (rear view - right connector) Un-P1-T6
HMC 1 (rear view - left connector) Un-P1-T7
HMC 2 (rear view - right connector) Un-P1-T8
Dual 1 GB Ethernet port 1 (top RJ45 connector) Un-P1-C6-T1
Dual 1 GB Ethernet port 2 (bottom RJ45 Un-P1-C6-T2
connector)
Quad 1 GB Ethernet port 1 (top RJ45 connector) Un-P1-C6-T1
Quad 1 GB Ethernet port 2 (middle top RJ45 Un-P1-C6-T2
connector)
Quad 1 GB Ethernet port 3 (middle bottom RJ45 Un-P1-C6-T3
connector)
Quad 1 GB Ethernet port 4 (bottom RJ45 Un-P1-C6-T4
connector)
External SAS port Un-P2-T1
Processor and processor regulator
Processor card 1 Un-P1-C13 Yes
Processor card 2 Un-P1-C14 Yes
Processor card 3 Un-P1-C15 Yes
Processor card 4 Un-P1-C16 Yes
Voltage regulator VRM1A on processor card 1 Un-P1-C13-C10 Yes
(both must be replaced as a pair)
Voltage regulator VRM1B on processor card 1 Un-P1-C13-C10 Yes
(both must be replaced as a pair)

22 Finding parts, locations, and addresses

Table 6. FRU location table (continued)
Failing item name Physical location code Identify LED
Voltage regulator VRM2 on processor card 1 Un-P1-C13-C5 Yes
Voltage regulator VRM1A on processor card 2 Un-P1-C14-C10 Yes
(both must be replaced as a pair)
Voltage regulator VRM1B on processor card 2 Un-P1-C14-C10 Yes
(both must be replaced as a pair)
Voltage regulator VRM2 on processor card 2 Un-P1-C14-C5 Yes
Voltage regulator VRM1A on processor card 3 Un-P1-C15-C10 Yes
(both must be replaced as a pair)
Voltage regulator VRM1B on processor card 3 Un-P1-C15-C10 Yes
(both must be replaced as a pair)
Voltage regulator VRM2 on processor card 3 Un-P1-C15-C5 Yes
Voltage regulator VRM1A on processor card 4 Un-P1-C16-C10 Yes
(both must be replaced as a pair)
Voltage regulator VRM1B on processor card 4 Un-P1-C16-C10 Yes
(both must be replaced as a pair)
Voltage regulator VRM2 on processor card 4 Un-P1-C16-C5 Yes
VPD card Un-P1-C9 Yes
Adapters
PCI-E adapter in slot 1 Un-P1-C1 Yes
PCI-E adapter in slot 2 Un-P1-C2 Yes
PCI-E adapter in slot 3 Un-P1-C3 Yes
PCI-X adapter in slot 4 Un-P1-C4 Yes
PCI-X adapter in slot 5 Un-P1-C5 Yes
Ethernet card Un-P1-C6 Yes
RIO/HSL/GX Dual-Port 12X Channel Attach Un-P1-C8 Yes
adapter controller slot 1 (rear view - second slot
from center)
RIO/HSL/GX Dual-Port 12X Channel Attach Un-P1-C7 Yes
adapter controller slot 2 (rear view - first slot
from center)
RIO/HSL/GX Dual-Port 12X Channel Attach Un-P1-C8-T1 Yes, for RIO adapter
adapter controller slot 1 port 1 (top connector) controller

No, for 12X Channel

Attach adapter
RIO/HSL/GX Dual-Port 12X Channel Attach Un-P1-C8-T2 Yes, for RIO adapter
adapter controller slot 1 port 2 (bottom controller
connector)
No, for 12X Channel
Attach adapter
RIO/HSL/GX Dual-Port 12X Channel Attach Un-P1-C7-T1 Yes, for RIO adapter
adapter controller slot 2 port 1 (top connector) controller

No, for 12X Channel

Attach adapter

Finding parts, locations, and addresses 23

Table 6. FRU location table (continued)
Failing item name Physical location code Identify LED
RIO/HSL/GX Dual-Port 12X Channel Attach Un-P1-C7-T2 Yes, for RIO adapter
adapter controller slot 2 port 2 (bottom controller
connector)
No, for 12X Channel
Attach adapter
Auxiliary cache card for system backplane Un-P1-C10 Yes
Auxiliary cache card battery Un-P1-C10-E1 No
RAID enablement card for system backplane Un-P1-C11 Yes
Thermal management card Un-P1-C12 Yes
Memory modules
Memory module 1 on processor 1 Un-P1-C13-C1 Yes
Memory module 2 on processor 1 Un-P1-C13-C2 Yes
Memory module 3 on processor 1 Un-P1-C13-C3 Yes
Memory module 4 on processor 1 Un-P1-C13-C4 Yes
Memory module 5 on processor 1 Un-P1-C13-C6 Yes
Memory module 6 on processor 1 Un-P1-C13-C7 Yes
Memory module 7 on processor 1 Un-P1-C13-C8 Yes
Memory module 8 on processor 1 Un-P1-C13-C9 Yes
Memory module 1 on processor 2 Un-P1-C14-C1 Yes
Memory module 2 on processor 2 Un-P1-C14-C2 Yes
Memory module 3 on processor 2 Un-P1-C14-C3 Yes
Memory module 4 on processor 2 Un-P1-C14-C4 Yes
Memory module 5 on processor 2 Un-P1-C14-C6 Yes
Memory module 6 on processor 2 Un-P1-C14-C7 Yes
Memory module 7 on processor 2 Un-P1-C14-C8 Yes
Memory module 8 on processor 2 Un-P1-C14-C9 Yes
Memory module 1 on processor 3 Un-P1-C15-C1 Yes
Memory module 2 on processor 3 Un-P1-C15-C2 Yes
Memory module 3 on processor 3 Un-P1-C15-C3 Yes
Memory module 4 on processor 3 Un-P1-C15-C4 Yes
Memory module 5 on processor 3 Un-P1-C15-C6 Yes
Memory module 6 on processor 3 Un-P1-C15-C7 Yes
Memory module 7 on processor 3 Un-P1-C15-C8 Yes
Memory module 8 on processor 3 Un-P1-C15-C9 Yes
Memory module 1 on processor 4 Un-P1-C16-C1 Yes
Memory module 2 on processor 4 Un-P1-C16-C2 Yes
Memory module 3 on processor 4 Un-P1-C16-C3 Yes
Memory module 4 on processor 4 Un-P1-C16-C4 Yes
Memory module 5 on processor 4 Un-P1-C16-C6 Yes
Memory module 6 on processor 4 Un-P1-C16-C7 Yes
Memory module 7 on processor 4 Un-P1-C16-C8 Yes

24 Finding parts, locations, and addresses

Table 6. FRU location table (continued)
Failing item name Physical location code Identify LED
Memory module 8 on processor 4 Un-P1-C16-C9 Yes
Device physical locations
Removable media Un-P2-D1 No
Removable media Un-P2-D2 No
Disk drive 1 Un-P2-D3 Yes
Disk drive 2 Un-P2-D4 Yes
Disk drive 3 Un-P2-D5 Yes
Disk drive 4 Un-P2-D6 Yes
Disk drive 5 Un-P2-D7 Yes
Disk drive 6 Un-P2-D8 Yes
Disk drive 7 Un-P2-D9 Yes
Disk drive 8 Un-P2-D10 Yes
Control panel
Control panel Un -D1
Temperature sensor Un -D1
Server firmware
Server firmware Un-Y1

8234-EMA, 9117-MMA, and 9406-MMA

The information provided in this topic defines specific sections of a location code string. Use this
information to understand the meaning of a location code.

Using location codes

For additional information about reading your location code, use the following table to link to a specific
topic.

Location code topics that might be of interest Description

Location code overview on page 26 Contains background information on the use of location
codes.
Physical location codes on page 26 Provides a definition for physical location code.
Logical location codes on page 26 Provides a definition for a logical location code.
Location code format on page 26 Provides descriptive information of the Un value in the
location code string. For example U5886.001.
Location code labels on page 27 Provides a table that identifies and defines the location
code labels. The location code labels begin with an
alphabetic character and follow the system serial number.
For example, U7879.001.10ABCDE-P3-C31-T2-L23. (The
system serial number is the 10ABCDE in the previous
example.) The P3, C31, T2, and L23 all contain an
alphabetic character that is identified in the Location
code labels table.
Worldwide unique identifier on page 28 Provides a definition for the worldwide unique identifier.
This group of digits follows the resource code labels and
always begins with the letter W.

Finding parts, locations, and addresses 25

Location code overview

Servers (system unit and expansion units) use physical location codes to provide mapping of replaceable
units. Location codes are produced by the server's firmware, which structures them so that they can be
used to identify specific parts in a system. The location code format is the same for all servers.

If you are working with a specific location code, the feature immediately follows the first character
(U5886). Refer to the Unit type and locations table.

If the location code ends with -Txx-Lxx, the server's firmware could not identify the physical location.
When a physical location cannot be identified, a logical location code is provided. Where logical location
codes occur in enclosures, the locations topic for the enclosure has the known conversions listed. For
logical location codes with no conversion, contact your next level of support.

If the location code begins with UTMPx, the expansion I/O unit's machine type, model and serial
number have not been set yet and this is a temporary unit identifier. To identify the unit, examine the
display panels on all of the expansion I/O units connected to the server until you find one with the same
characters in the first 5 digits of the top line in the unit's display. Record the unit's real machine type and
model from the unit label. Match the unit's machine type and model in the Unit type and locations table,
and follow the link to determine the service information.

Note: If locations for units are not in the preceding format, either they are not supported or there is a
problem in the firmware. Contact your next level of support.

Physical location codes

Physical location codes provide a mapping of logical functions and components (such as backplanes,
removable modules, connectors, ports, cables, and devices) to their specific locations within the physical
structure of the server.

Logical location codes

If the physical location cannot be mapped to a physical location code, the server's firmware generates a
logical location code. A logical location code is a sequence of location labels that identifies the path that
the system uses to communicate with a given resource.

Note: A resource has as many logical location codes as it has logical connections to the system. For
example, an external tape device connected to two I/O adapters will have two logical location codes.

An example of a logical location code is:

U7879.001.10ABCDE-P3-C31-T2-L23

The first part of the location code (through the T2 label) represents the physical location code for the
resource that communicates with the target resource. The remainder of the logical location code (L23)
represents exactly which resource is indicated.

Location code format

The location code is an alphanumeric string of variable length, consisting of a series of location
identifiers, separated by a dash. An example of a physical location for a fan is Un-A1.

The first position, represented by Un (where n is equal to any string contained between the U and the
hyphen) in the preceding example, is displayed in one of the forms in the following table.

26 Finding parts, locations, and addresses

Note: In location codes, the U is a constant digit; however, the numbered positions following the U are
variables and are dependent on your server. Each column defines the numbers that follow the U in the
beginning of the location code.

Machine type and model number in its location codes Feature codes and sequence numbers in its location
code

Utttt.mmm.sssssss-A1 Uffff.ccc.sssssss-A1
The leftmost code is always U. The leftmost code is always U.
tttt represents the unit type of the enclosure (drawer or ffff represents the feature code of the enclosure (drawer
node). or node).
mmm represents the model of the enclosure. ccc represents the sequence number of the enclosure .
sssssss represents the serial number for the enclosure. sssssss represents the serial number of the enclosure.
Note: The mmm or ccc number might not be displayed on all location codes for all servers. If the mmm value is not
displayed, the location code is displayed in one of the following forms:
v Utttt.sssssss-A1
v Uffff.sssssss-A1

The location code is hierarchical; that is, each location identifier in the string represents a physical part.
The order (from left to right), in which each identifier is shown, allows you to determine which parts
contain other parts in the string.

The dash (-) separator character represents a relationship between two components in the unit. In the
example of the fan, whose location code is Un-A1, the dash shows that the fan (A1) is contained in the
base unit (or Un). Modules, adapters, cables, and devices are all parts that are plugged into another part.
Their location codes always show that they are plugged into another part as components of the server.
Another example follows:, Un-P1-C9 is a memory DIMM, with memory DIMM (C9) plugged into a
backplane (P1), which is inside the unit (Un).

For more information about the various location code label prefixes, refer to Location code labels.

Note: For devices, certain error conditions might cause an IBM i device to display the device location in
an AIX format.
Table 7. Unit type and locations
Unit type (Utttt.mmm) Link to location information
U9406.MMA 9406.MMA Locations
U789D.001 9117.MMA Locations
U8234.EMA 8234.EMA Locations

Location code labels

The following table identifies the location code label prefixes.

Note: These labels apply to system units only.

Table 8. Location code label prefixes for system units
Prefix Description Example
A Air-moving device Fan, blower
C Card connector IOP, IOA, DIMM, processor card
D Device Diskette, control panel

Finding parts, locations, and addresses 27

Table 8. Location code label prefixes for system units (continued)
Prefix Description Example
E Electrical Battery, power supply, ac charger
L Logical path SAS target IDE address, fibre channel LUN
N Horizontal placement for an empty rack location
P Planar System backplane
T Port
U Unit
V Virtual planar
W Worldwide unique ID
X EIA value for an empty rack location
Y Firmware FRU

Worldwide unique identifier

A worldwide unique identifier location label consists of the prefix W followed by a maximum of 16
uppercase hexadecimal digits with no leading zeros. A location code might not consist of a worldwide
unique identifier. When present, the worldwide unique identifier location label follows the location label
of the resource that interfaces with the resource that has the worldwide unique identifier, usually a port.

Locations
The following table contains location codes for the parts that make up the server.

The following diagrams show field replaceable unit (FRU) layouts in the system. Use these diagrams with
the following tables.

Front

28 Finding parts, locations, and addresses

Rear

HEA card types

Your unit has one of the following card types. From left to right, the feature types are 5636, 5637, and
5639.

Finding parts, locations, and addresses 29

Memory module locations on the processor card (Un-P2-Cx)

Multiple node locations with SMP processor cable

Use the following illustration to map a node location when you are working with a multiple node
installation. All of the nodes have the same location codes inside the system unit; only the serial number
is different (Utttt.mmm.sssssss-).

Table 9. FRU location table

Failing item name Physical location code Identify LED
System unit Un
Fans
Fan 1 Un-A1 Yes
Fan 2 Un-A2 Yes
Power supplies
Power supply 1 Un-E1 Yes
Power supply 2 Un-E2 Yes

30 Finding parts, locations, and addresses

Table 9. FRU location table (continued)
Failing item name Physical location code Identify LED
Backplanes
Input/output backplane with embedded: Un-P1 Yes
v RIO Hub/HSL NIC
v RIO/HSL link
v Ethernet controller
v USB controller (AIX or Linux only)
v SAS controllers
v Logic oscillator
Regulator distribution connection backplane Un-P2 Yes
Disk drive backplane Un-P3 Yes
Media drive backplane Un-P4 Yes
Ports
System port 2 (back of system unit) Un-P1-C10-T3 (5636, 5637)
Un-P1-C10-T5 (5639)
System port 1 (back of system unit) Un-P1-C10-T4 (5636)
Integrated 2-port USB port 1 (AIX or Linux only) Un-P1-T1
Integrated 2-port USB port 2 (AIX or Linux only) Un-P1-T2
Integrated dual 1 GB ethernet controller Un-P1-C10-T2
Integrated dual 1 GB ethernet controller Un-P1-C10-T1
Integrated dual 1 GB ethernet controller Un-P1-C10-T3 (5639)
Integrated dual 1 GB ethernet controller Un-P1-C10-T4 (5639)
System cable connector Un-P1-C11-T5
Processor and processor regulator
Processor card 1 Un-P2-C1 Yes
Processor card 2 Un-P2-C2 Yes
SMP processor cable Un-P2-C1-T1

Un-P2-C1-T2

Un-P2-C2-T1

Un-P2-C2-T2
Temperature sensor Un -P2-C1

Un -P2-C2
Voltage regulator 1 Un-P2-C3 Yes
Voltage regulator 2 Un-P2-C4 Yes
Voltage regulator 3 Un-P2-C5 Yes

Finding parts, locations, and addresses 31

Table 9. FRU location table (continued)
Failing item name Physical location code Identify LED
VPD pass-through card Un-P1-C10
Feature 5636: serial port 1 at bottom is T4
and serial port 2 top is T3, Ethernet port 1
is T2 and port 2 is T1
Feature 5637: serial port 2 is T3, Ethernet
port 1 is T2 and port 2 is T1
Feature 5639: port 2 is T5, Ethernet Port 1
is T4 (top), port 2 is T3, port 3 is T2 and
port 4 is T1
VPD card Un-P1-C10-C1
Service processor
Service processor card Un-P1-C11 Yes
Service processor cable Un-P1-C11-T5
Time-of-day (TOD) Un-P1-C11
Time-of-day Battery Un-P1-C11-E1
HMC 1 connector Un-P1-C11-T3
HMC 2 connector Un-P1-C11-T4
SPCN 0 connector Un-P1-C11-T1
SPCN 1 connector Un-P1-C11-T2
Adapters
PCI adapter in slot 1 Un-P1-C1 Yes
PCI adapter in slot 2 Un-P1-C2 Yes
PCI adapter in slot 3 Un-P1-C3 Yes
PCI adapter in slot 4 Un-P1-C4 Yes
PCI adapter in slot 5 Un-P1-C5 Yes
PCI adapter in slot 6 Un-P1-C6 Yes
RIO/HSL adapter or Un-P1-C8 Yes

12x host channel adapter

RIO/HSL adapter or Un-P1-C9 Yes

12x host channel adapter

RIO/HSL adapter/ 12x host channel adapter Un-P1-C8-T1 Yes
connector
RIO/HSL adapter/ 12x host channel adapter Un-P1-C8-T2 Yes
connector
RIO/HSL adapter/ 12x host channel adapter Un-P1-C9-T1 Yes
connector
RIO/HSL adapter/ 12x host channel adapter Un-P1-C9-T2 Yes
connector
Memory modules
Memory module 1 Un-P2-C1-C1 Yes
Memory module 2 Un-P2-C1-C2 Yes
Memory module 3 Un-P2-C1-C3 Yes
Memory module 4 Un-P2-C1-C4 Yes

32 Finding parts, locations, and addresses

Table 9. FRU location table (continued)
Failing item name Physical location code Identify LED
Memory module 5 Un-P2-C1-C5 Yes
Memory module 6 Un-P2-C1-C6 Yes
Memory module 7 Un-P2-C1-C7 Yes
Memory module 8 Un-P2-C1-C8 Yes
Memory module 9 Un-P2-C1-C9 Yes
Memory module 10 Un-P2-C1-C10 Yes
Memory module 11 Un-P2-C1-C11 Yes
Memory module 12 Un-P2-C1-C12 Yes
Memory module 1 Un-P2-C2-C1 Yes
Memory module 2 Un-P2-C2-C2 Yes
Memory module 3 Un-P2-C2-C3 Yes
Memory module 4 Un-P2-C2-C4 Yes
Memory module 5 Un-P2-C2-C5 Yes
Memory module 6 Un-P2-C2-C6 Yes
Memory module 7 Un-P2-C2-C7 Yes
Memory module 8 Un-P2-C2-C8 Yes
Memory module 9 Un-P2-C2-C9 Yes
Memory module 10 Un-P2-C2-C10 Yes
Memory module 11 Un-P2-C2-C11 Yes
Memory module 12 Un-P2-C2-C12 Yes
Note: First quad of memory modules is plugged into memory module slots P2-Cx-C3, P2-Cx-C6, P2-Cx-C9, and
P2-Cx-C12. Second quad of memory modules is plugged into memory module slots P2-Cx-C2, P2-Cx-C5, P2-Cx-C8,
and P2-Cx-C11. Third quad of memory modules is plugged into memory module slots P2-Cx-C1, P2-Cx-C4,
P2-Cx-C7, and P2-Cx-C10.
Device physical locations
Disk drive 1 Un-P3-D1 (logical location with RAID card Yes

Un-P1-T13-L5-L0, logical location without

RAID card

Un-P1-T14-L5-L0)
Disk drive 2 Un-P3-D2 (logical location with RAID card Yes

Un-P1-T13-L4-L0, logical location without

RAID card Un-P1-T14-L4-L0)
Disk drive 3 Un-P3-D3 (logical location with RAID card Yes

Un-P1-T13-L3-L0, logical location without

RAID card

Un-P1-T14-L3-L0)
Disk drive 4 Un-P3-D4 (logical location with RAID card Yes

Un-P1-T12-L5-L0, logical location without

RAID card

Un-P1-T12-L5-L0)

Finding parts, locations, and addresses 33

Table 9. FRU location table (continued)
Failing item name Physical location code Identify LED
Disk drive 5 Un-P3-D5 (logical location with RAID card Yes

Un-P1-T12-L4-L0, logical location without

RAID card

Un-P1-T12-L4-L0)
Disk drive 6 Un-P3-D6 (logical location with RAID card Yes

Un-P1-T12-L3-L0, logical location without

RAID card

Un-P1-T12-L3-L0)
IDE drive 1 Un-P4-D1 Yes
Control panel
Control panel (bottom media bay) Un -D1
Control panel system port 1 Un -D1-T4
Server firmware
Server firmware Un-Y1

9119-FHA
The information provided in this topic defines specific sections of a location code string. Use this
information to understand the meaning of a location code.

Using location codes

For additional information about reading your location code, use the following table to link to a specific
topic.

Location code topics that might be of interest Description

Location code overview on page 35 Contains background information on the use of location
codes.
Physical location codes on page 35 Provides a definition for physical location code.
Logical location codes on page 35 Provides a definition for a logical location code.
Location code format on page 35 Provides descriptive information of the Un value in the
location code string. For example U5886.001.
Location code labels on page 36 Provides a table that identifies and defines the location
code labels. The location code labels begin with an
alphabetic character and follow the system serial number.
For example, U7879.001.10ABCDE-P3-C31-T2-L23. (The
system serial number is the 10ABCDE in the previous
example.) The P3, C31, T2, and L23 all contain an
alphabetic character that is identified in the Location
code labels table.
Worldwide unique identifier on page 37 Provides a definition for the worldwide unique identifier.
This group of digits follows the resource code labels and
always begins with the letter W.

34 Finding parts, locations, and addresses

Location code overview

Servers (system unit and expansion units) use physical location codes to provide mapping of replaceable
units. Location codes are produced by the server's firmware, which structures them so that they can be
used to identify specific parts in a system. The location code format is the same for all servers.

If you are working with a specific location code, the feature immediately follows the first character
(U5886). Refer to the Unit type and locations table.

If the location code ends with -Txx-Lxx, the server's firmware could not identify the physical location.
When a physical location cannot be identified, a logical location code is provided. Where logical location
codes occur in enclosures, the locations topic for the enclosure has the known conversions listed. For
logical location codes with no conversion, contact your next level of support.

If the location code begins with UTMPx, the expansion I/O unit's machine type, model and serial
number have not been set yet and this is a temporary unit identifier. To identify the unit, examine the
display panels on all of the expansion I/O units connected to the server until you find one with the same
characters in the first 5 digits of the top line in the unit's display. Record the unit's real machine type and
model from the unit label. Match the unit's machine type and model in the Unit type and locations table,
and follow the link to determine the service information.

Note: If locations for units are not in the preceding format, either they are not supported or there is a
problem in the firmware. Contact your next level of support.

Physical location codes

Physical location codes provide a mapping of logical functions and components (such as backplanes,
removable modules, connectors, ports, cables, and devices) to their specific locations within the physical
structure of the server.

Logical location codes

If the physical location cannot be mapped to a physical location code, the server's firmware generates a
logical location code. A logical location code is a sequence of location labels that identifies the path that
the system uses to communicate with a given resource.

Note: A resource has as many logical location codes as it has logical connections to the system. For
example, an external tape device connected to two I/O adapters will have two logical location codes.

An example of a logical location code is:

U7879.001.10ABCDE-P3-C31-T2-L23

The first part of the location code (through the T2 label) represents the physical location code for the
resource that communicates with the target resource. The remainder of the logical location code (L23)
represents exactly which resource is indicated.

Location code format

The location code is an alphanumeric string of variable length, consisting of a series of location
identifiers, separated by a dash. An example of a physical location for a fan is Un-A1.

The first position, represented by Un (where n is equal to any string contained between the U and the
hyphen) in the preceding example, is displayed in one of the forms in the following table.

Finding parts, locations, and addresses 35

Note: In location codes, the U is a constant digit; however, the numbered positions following the U are
variables and are dependent on your server. Each column defines the numbers that follow the U in the
beginning of the location code.

Machine type and model number in its location codes Feature codes and sequence numbers in its location
code

Utttt.mmm.sssssss-A1 Uffff.ccc.sssssss-A1
The leftmost code is always U. The leftmost code is always U.
tttt represents the unit type of the enclosure (drawer or ffff represents the feature code of the enclosure (drawer
node). or node).
mmm represents the model of the enclosure. ccc represents the sequence number of the enclosure .
sssssss represents the serial number for the enclosure. sssssss represents the serial number of the enclosure.
Note: The mmm or ccc number might not be displayed on all location codes for all servers. If the mmm value is not
displayed, the location code is displayed in one of the following forms:
v Utttt.sssssss-A1
v Uffff.sssssss-A1

The location code is hierarchical; that is, each location identifier in the string represents a physical part.
The order (from left to right), in which each identifier is shown, allows you to determine which parts
contain other parts in the string.

The dash (-) separator character represents a relationship between two components in the unit. In the
example of the fan, whose location code is Un-A1, the dash shows that the fan (A1) is contained in the
base unit (or Un). Modules, adapters, cables, and devices are all parts that are plugged into another part.
Their location codes will always show that they are plugged into another part as components of the
server. Another example follows:, Un-P1-C9 is a memory DIMM, with memory DIMM (C9) plugged into
a backplane (P1), which is inside the unit (Un).

For more information about the various location code label prefixes, refer to Location code labels.

Note: For devices, certain error conditions might cause an IBM i device to display the device location in
an AIX format.
Table 10. Unit type and locations
Unit type (Utttt.mmm) Link to location information
U9119.FHA Locations

Location code labels

The following table identifies the location code label prefixes.

Note: These labels apply to system units only.

Table 11. Location code label prefixes for system units
Prefix Description Example
A Air-moving device Fan, blower
C Card connector IOP, IOA, DIMM, processor card
D Device Diskette, control panel
E Electrical Battery, power supply, ac charger
L Logical path SAS target IDE address, fibre channel LUN

36 Finding parts, locations, and addresses

Table 11. Location code label prefixes for system units (continued)
Prefix Description Example
N Horizontal placement for an empty rack location
P Planar System backplane
T Port
U Unit
V Virtual planar
W Worldwide unique ID
X EIA value for an empty rack location
Y Firmware FRU

Worldwide unique identifier

A worldwide unique identifier location label consists of the prefix W followed by a maximum of 16
uppercase hexadecimal digits with no leading zeros. A location code might not consist of a worldwide
unique identifier. When present, the worldwide unique identifier location label follows the location label
of the resource that interfaces with the resource that has the worldwide unique identifier, usually a port.

Locations
Use this information to help you map a location code to a position on the unit.

Note: The known logical location codes for this unit are listed next to the corresponding physical location
in the following information. If you are working with a logical location code for this unit and it is not
listed in the following information, contact your next level of support.

The following diagrams show the field replaceable unit (FRU) layout in the system. Use these diagrams
with the following tables.

Finding parts, locations, and addresses 37

Figure 20. Front and rear views

Figure 21. Emergency power off (EPO)

38 Finding parts, locations, and addresses

Figure 22. Light strip views

Figure 23. Bulk power assembly (BPA). Front is Un-P1 and back is Un-P2.

Figure 24. Light strip views

Finding parts, locations, and addresses 39

Figure 25. Node locations

40 Finding parts, locations, and addresses

Figure 26. I/O hub card locations (top nodes)

Figure 27. I/O hub card locations (bottom nodes)

The following table provides location codes for parts that make up the server.

Finding parts, locations, and addresses 41

Table 12. Bulk power assembly (BPA) locations, and failing components
Failing item name Identify LED Physical location code
System unit bulk power assembly (BPA) Un
Bulk power distribution (BPD)
Bulk power regulator (BPR) 4A, top No Un-P1E1
Bulk power regulator (BPR) 3A No Un-P1E2
Bulk power regulator (BPR) 2A No Un-P1E3
Bulk power regulator (BPR) 1A No Un-P1E4
Bulk power controller (BPC) A No Un-P1C1
Bulk power distribution (BPD) 1A No Un-P1C2
Bulk power distribution (BPD) 2A No Un-P1C3
Bulk power hub (BPH) A No Un-P1C4
Bulk power fan (BPF) A No Un-A1
Bulk power assembly (BPA) B. Rear of frame, Un-P2
B side power boundary
Bulk power regulator (BPR) 4B, top No Un-P2E1
Bulk power regulator (BPR) 3B No Un-P2E2
Bulk power regulator (BPR) 2B No Un-P2E3
Bulk power regulator (BPR) 1B No Un-P2E4
Bulk power controller (BPC) B No Un-P2C1
Bulk power distribution (BPD) 1B No Un-P2C2
Bulk power distribution (BPD) 2B No Un-P2C3
Bulk power hub (BPH) B No Un-P2C4
Bulk power fan (BPF) B No Un-A2
UEPO panel Un-D1
Bulk power assembly (BPA)
BPR 4 Un-Px-E1
Connector J01 Un-Px-E1J01
BPR 3 Un-Px-E2
Connector J01 Un-Px-E2J01
BPR 2 Un-Px-E3
Connector J01, IBF Un-Px-E3J01
BPR 1 Un-Px-E4
Connector J01, IBF Un-Px-E4J01
Bulk power controller (BPC) Un-Px-C1
Connector J01, BPC cross communication No Un-Px-C1J01
Connector J02, ethernet to BPH No Un-Px-C1J02
Connector J03, ethernet to BPH No Un-Px-C1J03
Connector J04, UEPO panel No Un-Px-C1J04
Connector J06, BPF No Un-Px-C1J06
Connector J07, BPC cross power No Un-Px-C1J07

42 Finding parts, locations, and addresses

Table 12. Bulk power assembly (BPA) locations, and failing components (continued)
Failing item name Identify LED Physical location code
Connector J10, MDA 1 & 3, Y cable powers 2 No Un-Px-C1J10
MDAs
Connector J11, MDA 2 & 4, Y cable powers 2 No Un-Px-C1J11
MDAs
Bulk power distribution (BPD) connectors
BPD1 No Un-Px-C2
Connector J01, I/O drawer 1, DCA 2 No Un-Px-C2J01
Connector J02, I/O drawer 1, DCA 1 No Un-Px-C2J02
Connector J03, I/O drawer 2, DCA 2 No Un-Px-C2J03
Connector J04, I/O drawer 2, DCA 1 No Un-Px-C2J04
Connector J05, I/O drawer 3, DCA 2 No Un-Px-C2J05
Connector J06, I/O drawer 3, DCA 1 No Un-Px-C2J06
Connector J07, node P5 No Un-Px-C2J07
Connector J08, node P9 No Un-Px-C2J08
Connector J09, node P2 No Un-Px-C2J09
Connector J10, node P6 No Un-Px-C2J10
BPD2 No Un-Px-C3
Connector J01, I/O drawer 4, DCA 2 No Un-Px-C3J01
Connector J02, I/O drawer 4, DCA 1 No Un-Px-C3J02
Connector J03, I/O drawer 5, DCA 2 No Un-Px-C3J03
Connector J04, I/O drawer 5, DCA 1 No Un-Px-C3J04
Connector J05, I/O drawer 6, DCA 2 No Un-Px-C3J05
Connector J06, I/O drawer 6, DCA 1 No Un-Px-C3J06
Connector J07, node P4 or I/O drawer 7 No Un-Px-C3J07
Connector J08, node P3 or I/O drawer 8 No Un-Px-C3J08
Connector J09, node P8 or I/O drawer 9 No Un-Px-C3J09
Connector J10, node P7 or I/O drawer 10 No Un-Px-C3J10
Bulk power hub (BPH) No Un-Px-C4
Connector J01J24 No Un-Px-C4Jxx
UEPO panel Un-Px-D1
Connector J01, to BPC-A Un-Px-D1J01
Connector J02, to BPC-B Un-Px-D1J02
Central electronics complex (CEC)
Midplane Un-P1
Anchor card Yes Un-P1C1
FSP card 0 Yes Un-P1C2
Clock card 0 Yes Un-P1C3
Clock card 1 Yes Un-P1C4
FSP card 1 Yes Un-P1C5
Processor book 0, plugs into midplane Yes Un-P2

Finding parts, locations, and addresses 43

Table 12. Bulk power assembly (BPA) locations, and failing components (continued)
Failing item name Identify LED Physical location code
Processor book 1 Yes Un-P6
Processor book 2 Yes Un-P3
Processor book 3 Yes Un-P7
Processor book 4 Yes Un-P4
Processor book 5 Yes Un-P8
Processor book 6 Yes Un-P5
Processor book 7 Yes Un-P9
Air moving device AMD 1 Yes Un-A1
Motor drive assembly (MDA) MDA 1 Yes Un-A1E1
Air moving device AMD 2 Yes Un-A2
MDA 2 Yes Un-A2E1
Air moving device AMD 3 Yes Un-A3
MDA 3 Yes Un-A3E1
Air moving device AMD 4 Yes Un-A4
MDA 4 Yes Un-A4E1
Processor book Where m varies from 29
DCA 1 Yes Un-Pm-E2
DCA 2 Yes Un-Pm-E1
I/O hub cards Where m varies from 29
Slot T Yes Un-Pm-C40
Slot S Yes Un-Pm-C39
Slot U Yes Un-Pm-C38
Slot V Yes Un-Pm-C37
I/O hub card connectors Where m varies from 29
Slot T Yes Un-Pm-C40T01 and Un-Pm-C40T02
Slot S Yes Un-Pm-C39T01 and Un-Pm-C39T02
Slot U Yes Un-Pm-C38T01 and Un-Pm-C38T02
Slot V Yes Un-Pm-C37T01 and Un-Pm-C37T02
Book FSP card 1 Un-Pm-C42
Book FSP card 0 Un-Pm-C41
FSP card connector J01 Un-Pm-Cx-T01
FSP card connector J02 Un-Pm-Cx-T02
Memory Where m varies from 29
DIMM S1 Yes Un-Pm-C36
DIMM S2 Yes Un-Pm-C35
DIMM S3 Yes Un-Pm-C34
DIMM S4 Yes Un-Pm-C33
DIMM S5 Yes Un-Pm-C32
DIMM S6 Yes Un-Pm-C31
DIMM S7 Yes Un-Pm-C30

44 Finding parts, locations, and addresses

Table 12. Bulk power assembly (BPA) locations, and failing components (continued)
Failing item name Identify LED Physical location code
DIMM S8 Yes Un-Pm-C29
DIMM T1 Yes Un-Pm-C24
DIMM T2 Yes Un-Pm-C23
DIMM T3 Yes Un-Pm-C22
DIMM T4 Yes Un-Pm-C21
DIMM T5 Yes Un-Pm-C20
DIMM T6 Yes Un-Pm-C19
DIMM T7 Yes Un-Pm-C18
DIMM T8 Yes Un-Pm-C17
DIMM V1 Yes Un-Pm-C16
DIMM V2 Yes Un-Pm-C15
DIMM V3 Yes Un-Pm-C14
DIMM V4 Yes Un-Pm-C13
DIMM V5 Yes Un-Pm-C12
DIMM V6 Yes Un-Pm-C11
DIMM V7 Yes Un-Pm-C10
DIMM V8 Yes Un-Pm-C9
DIMM U1 Yes Un-Pm-C8
DIMM U2 Yes Un-Pm-C7
DIMM U3 Yes Un-Pm-C6
DIMM U4 Yes Un-Pm-C5
DIMM U5 Yes Un-Pm-C4
DIMM U6 Yes Un-Pm-C3
DIMM U7 Yes Un-Pm-C2
DIMM U8 Yes Un-Pm-C1
MCM-S Un-Pm-C28
MCM-T Un-Pm-C26
MCM-U Un-Pm-C25
MCM-V Un-Pm-C27
Front light strip Yes Un-P10
Back light strip Yes Un-P11
Central electronics complex (CEC) cage connectors
System controller 0, 1 Where m is 2 or 5
Connector J1, front light strip (J01 or J02) No Un-P1Cm-T1
Connector J2, back light strip (J01 or J02) No Un-P1Cm-T2
Connector J3, ethernet connects to BHP A Yes Un-P1Cm-T3
Connector J4Ethernet connects to BHP B Yes Un-P1Cm-T4
Connector J5, SPCN connector No Un-P1Cm-T5
Book connectors
Super UPIC power connector J01 No Un-Px-J01

Finding parts, locations, and addresses 45

Table 12. Bulk power assembly (BPA) locations, and failing components (continued)
Failing item name Identify LED Physical location code
Super UPIC power connector J02 No Un-Px-J02
Motor drive assembly (MDA) MDA 1 Yes Un-A2E1
MDA 2 Yes Un-A4E1
MDA 3 Yes Un-A3E1
MDA 4 Yes Un-A1E1
Device physical locations
Disk drive 1 Un-P3-D01 (logical location
P2-T6-L8-L0)
Disk drive 2 Un-P3-D02 (logical location
P2-T6-L9-L0)
Disk drive 3 Un-P3-D03 (logical location
P2-T6-L10-L0)
Disk drive 4 Un-P3-D04 (logical location
P2-T6-L11-L0)
Disk drive 5 Un-P4-D05 (logical location
P2-T5-L8-L0)
Disk drive 6 Un-P4-D06 (logical location
P2-T5-L9-L0)
Disk drive 7 Un-P4-D07 (logical location
P2-T5-L10-L0)
Disk drive 8 Un-P4-D08 (logical location
P2-T5-L11-L0)
Disk drive 9 Un-P5-D09 (logical location
P1-T6-L8-L0)
Disk drive 10 Un-P5-D10 (logical location
P1-T6-L9-L0)
Disk drive 11 Un-P5-D11 (logical location
P1-T6-L10-L0)
Disk drive 12 Un-P5-D12 (logical location
P1-T6-L11-L0)
Disk drive 13 Un-P6-D13 (logical location
P1-T5-L8-L0)
Disk drive 14 Un-P6-D14 (logical location
P1-T5-L9-L0)
Disk drive 15 Un-P6-D15 (logical location
P1-T5-L10-L0)
Disk drive 16 Un-P6-D16 (logical location
P1-T5-L11-L0)

Note:
1. The following table provides information necessary to identify the IOP to which an IOA is assigned.
v The left column indicates the domain in which IOA assignment is allowed.
v The right column is used to determine the IOP to which an IOA is assigned.
v The first position in the list must be an IOP. The remaining positions may be IOPs or IOAs. IOAs
are assigned to the first IOP located to their left in the list. Although IOAs can be manually
reassigned using SST/DST, the IOA assignments return to the default order after each IPL.

46 Finding parts, locations, and addresses

Table 13. Identify the IOP to which IOAs are assigned
Multi-adapter bridge domain / PCI bridge set IOA assignment rules
P1-C01 through P1-C04 P1-C02, P1-C03, P1-C04
P1-C05 through P1-C07 P1-C06, P1-C07
P2-C01 through P2-C04 P2-C02, P2-C03, P2-C04
P2-C05 through P2-C07 P2-C06, P2-C07

9125-F2A
The information provided in this topic defines specific sections of a location code string. Use this
information to understand the meaning of a location code.

Using location codes

For additional information about reading your location code, use the following table to link to a specific
topic.

Location code topics that might be of interest Description

Location code overview Contains background information on the use of location
codes.
Physical location codes on page 48 Provides a definition for physical location code.
Logical location codes on page 48 Provides a definition for a logical location code.
Location code format on page 48 Provides descriptive information of the Un value in the
location code string. For example U5886.001.
Location code labels on page 49 Provides a table that identifies and defines the location
code labels. The location code labels begin with an
alphabetic character and follow the system serial number.
For example, U7879.001.10ABCDE-P3-C31-T2-L23. (The
system serial number is the 10ABCDE in the previous
example.) The P3, C31, T2, and L23 all contain an
alphabetic character that is identified in the Location
code labels table.
Worldwide unique identifier on page 50 Provides a definition for the worldwide unique identifier.
This group of digits follows the resource code labels and
always begins with the letter W.

Location code overview

Servers (system unit and expansion units) use physical location codes to provide mapping of replaceable
units. Location codes are produced by the server's firmware, which structures them so that they can be
used to identify specific parts in a system. The location code format is the same for all servers.

If you are working with a specific location code, the feature immediately follows the first character
(U5886). Refer to the Unit type and locations table.

If the location code ends with -Txx-Lxx, the server's firmware could not identify the physical location.
When a physical location cannot be identified, a logical location code is provided. Where logical location
codes occur in enclosures, the locations topic for the enclosure has the known conversions listed. For
logical location codes with no conversion, contact your next level of support.

If the location code begins with UTMPx, the expansion I/O unit's machine type, model and serial
number have not been set yet and this is a temporary unit identifier. To identify the unit, examine the

Finding parts, locations, and addresses 47

display panels on all of the expansion I/O units connected to the server until you find one with the same
characters in the first 5 digits of the top line in the unit's display. Record the unit's real machine type and
model from the unit label. Match the unit's machine type and model in the Unit type and locations table,
and follow the link to determine the service information.

Note: If locations for units are not in the preceding format, either they are not supported or there is a
problem in the firmware. Contact your next level of support.

Physical location codes

Physical location codes provide a mapping of logical functions and components (such as backplanes,
removable modules, connectors, ports, cables, and devices) to their specific locations within the physical
structure of the server.

Logical location codes

If the physical location cannot be mapped to a physical location code, the server's firmware generates a
logical location code. A logical location code is a sequence of location labels that identifies the path that
the system uses to communicate with a given resource.

Note: A resource has as many logical location codes as it has logical connections to the system. For
example, an external tape device connected to two I/O adapters will have two logical location codes.

An example of a logical location code is:

U7879.001.10ABCDE-P3-C31-T2-L23

The first part of the location code (through the T2 label) represents the physical location code for the
resource that communicates with the target resource. The remainder of the logical location code (L23)
represents exactly which resource is indicated.

Location code format

The location code is an alphanumeric string of variable length, consisting of a series of location
identifiers, separated by a dash. An example of a physical location for a fan is Un-A1.

The first position, represented by Un (where n is equal to any string contained between the U and the
hyphen) in the preceding example, is displayed in one of the forms in the following table.

Note: In location codes, the U is a constant digit; however, the numbered positions following the U are
variables and are dependent on your server. Each column defines the numbers that follow the U in the
beginning of the location code.

Machine type and model number in its location codes Feature codes and sequence numbers in its location
code

Utttt.mmm.sssssss-A1 Uffff.ccc.sssssss-A1
The leftmost code is always U. The leftmost code is always U.
tttt represents the unit type of the enclosure (drawer or ffff represents the feature code of the enclosure (drawer
node). or node).
mmm represents the model of the enclosure. ccc represents the sequence number of the enclosure .
sssssss represents the serial number for the enclosure. sssssss represents the serial number of the enclosure.

48 Finding parts, locations, and addresses

Machine type and model number in its location codes Feature codes and sequence numbers in its location
code

Utttt.mmm.sssssss-A1 Uffff.ccc.sssssss-A1
Note: The mmm or ccc number might not be displayed on all location codes for all servers. If the mmm value is not
displayed, the location code is displayed in one of the following forms:
v Utttt.sssssss-A1
v Uffff.sssssss-A1

The location code is hierarchical; that is, each location identifier in the string represents a physical part.
The order (from left to right), in which each identifier is shown, allows you to determine which parts
contain other parts in the string.

The dash (-) separator character represents a relationship between two components in the unit. In the
example of the fan, whose location code is Un-A1, the dash shows that the fan (A1) is contained in the
base unit (or Un). Modules, adapters, cables, and devices are all parts that are plugged into another part.
Their location codes will always show that they are plugged into another part as components of the
server. Another example follows:, Un-P1-C9 is a memory DIMM, with memory DIMM (C9) plugged into
a backplane (P1), which is inside the unit (Un).

For more information about the various location code label prefixes, refer to Location code labels.

Note: For devices, certain error conditions might cause an IBM i device to display the device location in
an AIX format.
Table 14. Unit type and locations
Unit type (Utttt.mmm) Link to location information
U9125.F2A Locations
U9A00.100 VPD designation for the BPC, see Locations
U78A1.001 VPD designation for the node, see Locations

Location code labels

The following table identifies the location code label prefixes.

Note: These labels apply to system units only.

Table 15. Location code label prefixes for system units
Prefix Description Example
A Air-moving device Fan, blower
C Card connector IOP, IOA, DIMM, processor card
D Device Diskette, control panel
E Electrical Battery, power supply, ac charger
L Logical path SAS target IDE address, fibre channel LUN
N Horizontal placement for an empty rack location
P Planar System backplane
T Port
U Unit
V Virtual planar

Finding parts, locations, and addresses 49

Table 15. Location code label prefixes for system units (continued)
Prefix Description Example
W Worldwide unique ID
X EIA value for an empty rack location
Y Firmware FRU

Worldwide unique identifier

A worldwide unique identifier location label consists of the prefix W followed by a maximum of 16
uppercase hexadecimal digits with no leading zeros. A location code might not consist of a worldwide
unique identifier. When present, the worldwide unique identifier location label follows the location label
of the resource that interfaces with the resource that has the worldwide unique identifier, usually a port.

Locations
Use this information to help you map a location code to a position on the unit.

Note: The known logical location codes for this unit are listed next to the corresponding physical location
in the following information. If you are working with a logical location code for this unit and it is not
listed in the following information, contact your next level of support.

The following diagrams show the field replaceable unit (FRU) layout in the system. Use these diagrams
with the following tables.

Figure 28. Front and rear views

50 Finding parts, locations, and addresses

Figure 29. Emergency power off (EPO)

Figure 30. Modular water unit (MWU)

Figure 31. Bulk power assembly (BPA). Front is Un-A1 and back is Un-A2

Finding parts, locations, and addresses 51

Figure 32. I/O full assembly and I/O full assembly with two GX adapters

Figure 33. System view

The following table provides location codes for parts that make up the server.

52 Finding parts, locations, and addresses

Table 16. Bulk power assembly (BPA) locations, and failing components
Failing item name Symbolic FRU name Physical location code
System unit bulk power assembly Un
(BPA)
Bulk power hub (BPH) Where:
v Cage A is Un-P1-C1
v Cage B is Un-P2-C1
Bulk power hub (BPH) Un-Px-C1
Connector J01 Un-Px-C1-T1
Connector J02 Un-Px-C1-T2
Connector J03 Un-Px-C1-T3
Connector J04 Un-Px-C1-T4
Connector J05 Un-Px-C1-T5
Connector J06 Un-Px-C1-T6
Connector J07 Un-Px-C1-T7
Connector J08 Un-Px-C1-T8
Connector J09 Un-Px-C1-T9
Connector J10 Un-Px-C1-T10
Connector J11 Un-Px-C1-T11
Connector J12 Un-Px-C1-T12
Connector J13 Un-Px-C1-T13
Connector J14 Un-Px-C1-T14
Connector J15 Un-Px-C1-T15
Connector J16 Un-Px-C1-T16
Bulk power distribution (BPD) Where:
v Side A, top most is Un-P1-C3
v Side A, bottom most is Un-P1-C4
v Side B, top most is Un-P2-C2
v Side B, bottom most is Un-P2-C4
Bulk power distribution (BPD) x Un-Px-Cx
Bulk power distribution (BPD) x Un-Px-Cx-T1
connector J01
Bulk power distribution (BPD) x Un-Px-Cx-T2
connector J02
Bulk power distribution (BPD) x Un-Px-Cx-T3
connector J03
Bulk power distribution (BPD) x Un-Px-Cx-T4
connector J04
Bulk power distribution (BPD) x Un-Px-Cx-T5
connector J05
Bulk power distribution (BPD) n Un-Px-Cx-T6
connector J06
Bulk power distribution (BPD) x Un-Px-Cx-T7
connector J07

Finding parts, locations, and addresses 53

Table 16. Bulk power assembly (BPA) locations, and failing components (continued)
Failing item name Symbolic FRU name Physical location code
Bulk power regulator (BPR) Where:
v Cage A is Un-P1
v Cage B is Un-P2
Bulk power controller (BPC) Un-Px
BPR 11 Un-Px-E6
Connector J00 Un-Px-E6T1
BPR 9 Un-Px-E5
Connector J00 Un-Px-E5T1
BPR 7 Un-Px-E4
Connector J00 Un-Px-E4T1
BPR 5 Un-Px-E3
Connector J00 Un-Px-E3T1
BPR 3 Un-Px-E2
Connector J00 Un-Px-E2T1
BPR 1 Un-Px-E1
Connector J00 Un-Px-E1T1
Bulk power controller (BPC)
Bulk power controller (BPC) Un-P1C2
Connector J01 Un-P1C2T1
Connector J02 Un-P1C2T2
Connector J03 Un-P1C2T3
Connector J04 Un-P1C2T4
Connector J05 Un-P1C2T5
Connector J06 Un-P1C2T6
Connector J07 Un-P1C2T7
Connector J08 Un-P1C2T8
Connector J09 Un-P1C2T9
Bulk power fan (BPF)
Bulk power fan (BPF) A (front) Un-A1
Bulk power fan (BPF) B (back) Un-A2
Emergency power off (EPO)
Emergency power off (EPO) Un-D1
Emergency power off (EPO) Un-D1-J01
connector J01, BPA connection
Emergency power off (EPO) J02, Un-D1-J02
BPA connection
Emergency power off (EPO) J03, Un-D1-J03
room connection
Integrated battery feature (IBF)
IBF11 Un-E1
IBF11, connector J01 Un-E1-J01

54 Finding parts, locations, and addresses

Table 16. Bulk power assembly (BPA) locations, and failing components (continued)
Failing item name Symbolic FRU name Physical location code
IBF9 Un-E2
IBF9, connector J01 Un-E2-J01
IBF7 Un-E3
IBF7, connector J01 Un-E3-J01
IBF5 Un-E4
IBF5, connector J01 Un-E4-J01
IBF3 Un-E5
IBF3, connector J01 Un-E5-J01
IBF1 Un-E6
IBF1, connector J01 Un-E6-J01
IBF12 Un-E7
IBF12, connector J01 Un-E7-J01
IBF10 Un-E8
IBF10, connector J01 Un-E8-J01
IBF8 Un-E9
IBF8, connector J01 Un-E9-J01
IBF6 Un-E10
IBF6, connector J01 Un-E10-J01
IBF4 Un-E11
IBF4, connector J01 Un-E11-J01
IBF2 Un-E12
IBF2, connector J01 Un-E12-J01
Bulk power assembly BPA Where:
v Bulk power assembly (BPA) A (front) is Un-P1
v Bulk power assembly (BPA) B (back) is Un-P2
BPA Un-Px
Line cord 1 powers BPRs 1,2,3 Un-Px-J02
Line cord 2 powers BPRs 4,5,6 Un-Px-J01
BPR 6 Un-Px-E1
Connector J01 Un-Px-E1-J01
BPR 5 Un-Px-E2
Connector J01 Un-Px-E2-J01
BPR 4 Un-Px-E3
Connector J01 Un-Px-E3-J01
BPR 3 Un-Px-E4
Connector J01 Un-Px-E4-J01
BPR 2 Un-Px-E5
Connector J01 Un-Px-E5-J01
BPR 1 Un-Px-E6
Connector J01 Un-Px-E6-J01

Finding parts, locations, and addresses 55

Table 16. Bulk power assembly (BPA) locations, and failing components (continued)
Failing item name Symbolic FRU name Physical location code
Bulk power distribution (BPD) Top
BPD Un-Px-C2
Connector J01 Un-Px-C2-J01
Connector J02 Un-Px-C2-J02
Connector J03 Un-Px-C2-J03
Connector J04 Un-Px-C2-J04
Connector J05 Un-Px-C2-J05
Connector J06 Un-Px-C2-J06
Connector J07 Un-Px-C2-J07
Bulk power distribution (BPD) Bottom
BPD Un-Px-C3
Connector J01 Un-Px-C3-J01
Connector J02 Un-Px-C3-J02
Connector J03 Un-Px-C3-J03
Connector J04 Un-Px-C3-J04
Connector J05 Un-Px-C3-J05
Connector J06 Un-Px-C3-J06
Connector J07 Un-Px-C3-J07
Modular water units (MWU) Where:
v Modular Water Units A is Un-P3
v Modular Water Unit B is Un-P4
MWU Un-Px-C1
Connector J01 Un-Px-C1-J01
Connector J02 Un-Px-C1-J02
Fill and drain tool (FDT)
Front frame connector Un-J01
Rear frame connector Un-J02
FDT front Un-P5
Control card Un-P5-C1
FDT back Un-P6
Control card Un-P6-C1

Table 17. Processor subsystem assembly locations, and failing components

Failing item name Symbolic failing item Physical location code Identify LED
name
System unit Un
Fan
Fan Un-A1 Yes
Power supply (DCA)
Power supply Un-E1 Yes

56 Finding parts, locations, and addresses

Table 17. Processor subsystem assembly locations, and failing components (continued)
Failing item name Symbolic failing item Physical location code Identify LED
name
Power supply connector 1 Un-E1-J01
Power supply connector 2 Un-E1-J02
Backplane
System backplane Un-P1 Yes
Time-of-day battery TOD_BAT Un-P1-E1
Processor backplane ANYPROC Un-P2 Yes
v System processor MEMBRD
MEMCTLR
System backplane ports
IB 12x left communication Un-P1-T1
port, rear
IB 12x right communication Un-P1-T2
port, rear
10 GB optical, rear left Un-P1-T3
10 GB optical, rear right Un-P1-T4
SAS connector Un-P1-T5 Yes
1 GB ethernet port 1, rear Un-P1-T6 Yes
1 GB ethernet port 2, rear Un-P1-T7 Yes
1 GB ethernet port 3, rear Un-P1-T8 Yes
1 GB ethernet port 4, rear Un-P1-T9 Yes
HMC 1 (FSP) Un-P1-T10 Yes
HMC 2 (FSP) Un-P1-T11 Yes
Adapters
GX adapter 0 Un-P2-C65 Yes
GX adapter 0, port 0 Un-P2-C65-T1 Yes
GX adapter 0, port 1 Un-P2-C65-T2 Yes
GX adapter 0, port 2 Un-P2-C65-T3 Yes
GX adapter 0, port 3 Un-P2-C65-T4 Yes
GX adapter 1 Un-P2-C66 Yes
GX adapter 1, port 0 Un-P2-C66-T1 Yes
GX adapter 1, port 1 Un-P2-C66-T2 Yes
GX adapter 1, port 2 Un-P2-C66-T3 Yes
GX adapter 1, port 3 Un-P2-C66-T4 Yes
Memory modules
Memory module 1 MEMDIMM Un-P2-C1 Yes
Memory module 2 MEMDIMM Un-P2-C2 Yes
Memory module 3 MEMDIMM Un-P2-C3 Yes
Memory module 4 MEMDIMM Un-P2-C4 Yes
Memory module 5 MEMDIMM Un-P2-C5 Yes
Memory module 6 MEMDIMM Un-P2-C6 Yes

Finding parts, locations, and addresses 57

Table 17. Processor subsystem assembly locations, and failing components (continued)
Failing item name Symbolic failing item Physical location code Identify LED
name
Memory module 7 MEMDIMM Un-P2-C7 Yes
Memory module 8 MEMDIMM Un-P2-C8 Yes
Memory module 9 MEMDIMM Un-P2-C9 Yes
Memory module 10 MEMDIMM Un-P2-C10 Yes
Memory module 11 MEMDIMM Un-P2-C11 Yes
Memory module 12 MEMDIMM Un-P2-C12 Yes
Memory module 13 MEMDIMM Un-P2-C13 Yes
Memory module 14 MEMDIMM Un-P2-C14 Yes
Memory module 15 MEMDIMM Un-P2-C15 Yes
Memory module 16 MEMDIMM Un-P2-C16 Yes
Memory module 17 MEMDIMM Un-P2-C17 Yes
Memory module 18 MEMDIMM Un-P2-C18 Yes
Memory module 19 MEMDIMM Un-P2-C19 Yes
Memory module 20 MEMDIMM Un-P2-C20 Yes
Memory module 21 MEMDIMM Un-P2-C21 Yes
Memory module 22 MEMDIMM Un-P2-C22 Yes
Memory module 23 MEMDIMM Un-P2-C23 Yes
Memory module 24 MEMDIMM Un-P2-C24 Yes
Memory module 25 MEMDIMM Un-P2-C25 Yes
Memory module 26 MEMDIMM Un-P2-C26 Yes
Memory module 27 MEMDIMM Un-P2-C27 Yes
Memory module 28 MEMDIMM Un-P2-C28 Yes
Memory module 29 MEMDIMM Un-P2-C29 Yes
Memory module 30 MEMDIMM Un-P2-C30 Yes
Memory module 31 MEMDIMM Un-P2-C31 Yes
Memory module 32 MEMDIMM Un-P2-C32 Yes
Memory module 33 MEMDIMM Un-P2-C33 Yes
Memory module 34 MEMDIMM Un-P2-C34 Yes
Memory module 35 MEMDIMM Un-P2-C35 Yes
Memory module 36 MEMDIMM Un-P2-C36 Yes
Memory module 37 MEMDIMM Un-P2-C37 Yes
Memory module 38 MEMDIMM Un-P2-C38 Yes
Memory module 39 MEMDIMM Un-P2-C39 Yes
Memory module 40 MEMDIMM Un-P2-C40 Yes
Memory module 41 MEMDIMM Un-P2-C41 Yes
Memory module 42 MEMDIMM Un-P2-C42 Yes
Memory module 43 MEMDIMM Un-P2-C43 Yes
Memory module 44 MEMDIMM Un-P2-C44 Yes
Memory module 45 MEMDIMM Un-P2-C45 Yes

58 Finding parts, locations, and addresses

Table 17. Processor subsystem assembly locations, and failing components (continued)
Failing item name Symbolic failing item Physical location code Identify LED
name
Memory module 46 MEMDIMM Un-P2-C46 Yes
Memory module 47 MEMDIMM Un-P2-C47 Yes
Memory module 48 MEMDIMM Un-P2-C48 Yes
Memory module 49 MEMDIMM Un-P2-C49 Yes
Memory module 50 MEMDIMM Un-P2-C50 Yes
Memory module 51 MEMDIMM Un-P2-C51 Yes
Memory module 52 MEMDIMM Un-P2-C52 Yes
Memory module 53 MEMDIMM Un-P2-C53 Yes
Memory module 54 MEMDIMM Un-P2-C54 Yes
Memory module 55 MEMDIMM Un-P2-C55 Yes
Memory module 56 MEMDIMM Un-P2-C56 Yes
Memory module 57 MEMDIMM Un-P2-C57 Yes
Memory module 58 MEMDIMM Un-P2-C58 Yes
Memory module 59 MEMDIMM Un-P2-C59 Yes
Memory module 60 MEMDIMM Un-P2-C60 Yes
Memory module 61 MEMDIMM Un-P2-C61 Yes
Memory module 62 MEMDIMM Un-P2-C62 Yes
Memory module 63 MEMDIMM Un-P2-C63 Yes
Memory module 64 MEMDIMM Un-P2-C64 Yes
Device locations
Disk drive 1 Un-P1-D1
Disk drive 2 Un-P1-D2
Feature 5798 Where:
v Front right DCA is Un-E1
v Front left DCA is Un-E2
v Font left backplane is Un-P1
v Front back backplane is Un-P2
DCA Un-Ex Yes
DCA Super UPIC connector, Un-Ex-T1 Yes
left front
DCA Super UPIC connector, Un-Ex-T2 Yes
right front
Fan 1 Un-A1 Yes
Fan 2 Un-A2 Yes
Fan 3 Un-A3 Yes
Fan 4 Un-A4 Yes

Finding parts, locations, and addresses 59

Table 17. Processor subsystem assembly locations, and failing components (continued)
Failing item name Symbolic failing item Physical location code Identify LED
name
Backplane MA_BRDG MABRCFG Un-Px Yes
PPCITWR PRI_PCI
SI_PHB SIIOADP
PIOCARD MASBUS
SLOTERR SIADPCD
HSL_I4 HSL_LNK
TWRPLNR
Slot 1 PIOCARD MASBUS Un-Px-C1 Yes
SLOTERR
Slot 2 PIOCARD MASBUS Un-Px-C2 Yes
SLOTERR
Slot 3 PIOCARD MASBUS Un-Px-C3 Yes
SLOTERR
Slot 4 PIOCARD MASBUS Un-Px-C4 Yes
SLOTERR
Slot 5 PIOCARD MASBUS Un-Px-C5 Yes
SLOTERR
Slot 6 PIOCARD MASBUS Un-Px-C6 Yes
SLOTERR
Slot 7 PIOCARD MASBUS Un-Px-C7 Yes
SLOTERR
Slot 8 PIOCARD MASBUS Un-Px-C8 Yes
SLOTERR
Slot 9 PIOCARD MASBUS Un-Px-C9 Yes
SLOTERR
Slot 10 PIOCARD MASBUS Un-Px-C10 Yes
SLOTERR
IB riser port, right front Un-Px-T1 Yes
IB riser port, left front Un-Px-T2 Yes
DASD backplane 1 Un-P3 Yes
DASD backplane 2 Un-P4 Yes
DASD backplane 3 Un-P5 Yes
DASD backplane 4 Un-P6 Yes
Media bay power connector Un-PxT3
Integrated SCSI controller Un-PxT4
port
Integrated SCSI controller Un-PxT5
port
DASD 1 Un-P3D01 Yes
DASD 2 Un-P3D02 Yes
DASD 3 Un-P3D03 Yes
DASD 4 Un-P3D04 Yes
DASD 5 Un-P4D05 Yes
DASD 6 Un-P4D06 Yes
DASD 7 Un-P4D07 Yes

60 Finding parts, locations, and addresses

Table 17. Processor subsystem assembly locations, and failing components (continued)
Failing item name Symbolic failing item Physical location code Identify LED
name
DASD 8 Un-P4D08 Yes
DASD 9 Un-P5D09 Yes
DASD 10 Un-P5D10 Yes
DASD 11 Un-P5D11 Yes
DASD 12 Un-P5D12 Yes
DASD 13 Un-P6D13 Yes
DASD 14 Un-P6D14 Yes
DASD 15 Un-P6D15 Yes
DASD 16 Un-P6D16 Yes

0595, 5095, and 7311-D20

The information provided in this topic defines specific sections of a location code string. Use this
information to understand the meaning of a location code.

Using location codes

Use the following table to link to a specific topic for additional information when reading and
understanding your location code.
Table 18. Location code topics
Location code topics Description
Location code overview Contains background information about using location
codes.
Physical location codes on page 62 Provides definitions for physical location codes.
Logical location codes on page 62 Provides definitions for logical location codes.
Location code format on page 62 Provides format information of the Un value in the
location code string. For example U7031.001.
Location code labels on page 63 Provides definitions for location code labels. The location
code labels begin with an alphabetic character and follow
the system serial number. For example,
U7031.001.10ABCDE-P3-C31-T2-L23. (The system serial
number is the 10ABCDE.) The P3, C31, T2, and L23 all
contain an alphabetic character that is identified in the
Location code labels table.
Worldwide unique identifier on page 64 Provides definitions for the worldwide unique
identifiers. This group of digits follows the resource code
labels and always begins with the letter W.

Location code overview

Servers (system unit and expansion units) use physical location codes to provide mapping of replaceable
units. Location codes are produced by the server's firmware, which structures them so that they can be
used to identify specific parts in a system. The location code format is the same for all servers.

If you are working with a specific location code, the unit type and model immediately follow the first
character (Utttt.mmm).

Finding parts, locations, and addresses 61

v If the location code ends with -Txx-Lxx, the server's firmware could not identify the physical location.
When a physical location cannot be identified, a logical location code is provided. Where logical
location codes occur in enclosures, the locations topic for the enclosure has the known conversions
listed. For logical location codes with no conversion, contact your next level of support.
v If the location code begins with UTMPx, the expansion I/O unit's machine type, model number and
serial number have not been set yet and this is a temporary unit identifier. To identify the unit, do the
following:
1. Examine the display panels on all of the I/O enclosures that are connected to the server until you
find one with the same characters in the first 5 digits of the top line in the enclosure's display.
2. Record the I/O enclosure's real machine type and model from the I/O enclosure label.
3. Match the I/O enclosure's machine type and model in the unit type and locations table and then
follow the link to determine the service information.

Note: If you have a location code that does not follow the location code format as described in
Location code format it is either not supported or there is a problem in the firmware. Contact your
next level of support.

Physical location codes

Physical location codes provide a mapping of logical functions and components (such as backplanes,
removable modules, connectors, ports, cables, and devices) to their specific locations within the physical
structure of the server.

Logical location codes

If the physical location cannot be mapped to a physical location code, the server's firmware generates a
logical location code. A logical location code is a sequence of location labels that identifies the path that
the system uses to communicate with a given resource.

A resource has as many logical location codes as it has logical connections to the system. For example, an
external tape device connected to two I/O adapters will have two logical location codes.

An example of a logical location code is:

U7031.001.10ABCDE-P3-C31-T2-L23

The first part of the location code (through the T2 label) represents the physical location code for the
resource that communicates with the target resource. The remainder of the logical location code (L23)
represents exactly which resource is indicated.

Location code format

The location code is an alphanumeric string of variable length, consisting of a series of location
identifiers, separated by a dash. An example of a physical location for a fan is Un-A1.

The first position, represented by Un (where n is equal to any string contained between the U and the
hyphen) in the preceding example, is displayed in one of the forms in the following table.

Note: In location codes, the U is a constant digit. However, the numbered positions following the U are
variables and are dependent on your server. Each row in the following table defines the numbers that
follow the U in the beginning of the location code.

62 Finding parts, locations, and addresses

Machine type and model number in its location codes Feature codes and sequence numbers in its location
code

Utttt.mmm.sssssss-A1 Uffff.ccc.sssssss-A1
The leftmost code is always U. The leftmost code is always U.
tttt represents the unit type of the enclosure (drawer or ffff represents the feature code of the enclosure (drawer
node). or node).
mmm represents the model of the enclosure. ccc represents the sequence number of the enclosure .
sssssss represents the serial number for the enclosure. sssssss represents the serial number of the enclosure.
Note: The mmm or ccc number might not be displayed on all location codes for all servers. If the mmm value is not
displayed, the location code is displayed in one of the following forms:
v Utttt.sssssss-A1
v Uffff.sssssss-A1

The location code is hierarchical; that is, each location identifier in the string represents a physical part.
The order (from left to right), in which each identifier is shown, allows you to determine which parts
contain other parts in the string.

The dash (-) separator character represents a relationship between two components in the unit. In the
example of the fan, whose location code is Un-A1, the dash shows that the fan (A1) is contained in the
base unit (or Un). Modules, adapters, cables, and devices are all parts that are plugged into another part.
Their location codes will always show that they are plugged into another part as components of the
server. Another example follows:, Un-P1-C9 is a memory DIMM, with memory DIMM (C9) plugged into
a backplane (P1), which is inside the unit (Un).

For more information about the various location code label prefixes, refer to Location code labels.

Note: For devices, certain error conditions might cause an IBM i device to display the device location in
an AIX format.

Note: For devices, certain error conditions might cause an IBM i device to display the device location in
an AIX format.
Table 19. Unit type and locations
Unit type (Utttt.mmm) Link to location information
U0595.001 Locations
U5095.001 Locations
U7311.D20 Locations

Location code labels

The following table describes the location code label prefixes. These labels apply to system units only.
Table 20. Location code label prefixes for system units
Prefix Description Example
A Air-moving device Fan, blower
C Card connector IOP, IOA, DIMM, processor card
D Device Diskette, control panel
E Electrical Battery, power supply, ac charger
L Logical path SCSI target IDE address, fibre channel LUN

Finding parts, locations, and addresses 63

Table 20. Location code label prefixes for system units (continued)
Prefix Description Example
N Horizontal placement for an empty rack location
P Planar System backplane
T Port
U Unit
V Virtual planar
W Worldwide unique ID
X EIA value for an empty rack location
Y Firmware field replaceable unit (FRU)

Worldwide unique identifier

A worldwide unique identifier location label consists of the prefix W followed by a maximum of 16
uppercase hexadecimal digits with no leading zeros. A location code might not consist of a worldwide
unique identifier. When present, the worldwide unique identifier location label follows the location label
of the resource that interfaces with the resource that has the worldwide unique identifier, usually a port.

Locations
Learn how to locate field replaceable units (FRUs) by using logical and physical location codes.

Note: The known logical location codes for this unit are listed next to the corresponding physical location
in the following information. If you are working with a logical location code for this unit and it is not
listed in the following information, contact your next level of support.

The following diagrams show field replaceable unit (FRU) layout in the expansion unit. Use these
diagrams with the following tables.

Note: Some units may have labels that designate location codes other than those shown in the following
illustrations and tables. If that is the case, use the location codes shown in the following illustrations and
tables.

Figure 34. Front view of the expansion unit

64 Finding parts, locations, and addresses

Figure 35. Back view of the expansion unit

Figure 36. Top view of the expansion unit

The following table gives the components available for callout on the expansion units, and matches those
components with the FRU containing the component. For part numbers associated with failing
components, see 0595, 5095, and 7311-D20 system parts on page 190.

Finding parts, locations, and addresses 65

Table 21. FRU locations and failing components for the expansion unit
Failing item name Physical location code Identify LED
Backplane Un-P1 Yes
v SPCN
v Card enclosure or backplane
v Multi-adapter bridge (all)
PCI adapter in slot 1 Un-P1-C01 Yes
PCI adapter in slot 2 Un-P1-C02 Yes
PCI adapter in slot 3 Un-P1-C03 Yes
PCI adapter in slot 4 Un-P1-C04 Yes
RIO/HSL adapter Un-P1-C05 Yes
RIO/HSL adapter connector (bottom Un-P1-C05-00 Yes
connector
RIO/HSL adapter connector (top connector) Un-P1-C05-01 Yes
PCI adapter in slot 6 Un-P1-C06 Yes
PCI adapter in slot 7 Un-P1-C07 Yes
PCI adapter in slot 8 Un-P1-C08 Yes
PCI bridge set 1 Un-P1
Un-P1-C01
Un-P1-C02
Un-P1-C03
Un-P1-C04
PCI bridge set 2 Un-P1
Un-P1-C06
Un-P1-C07
Un-P1-C08
EPO connector (J11) Un-P1-T1
UPS connector (J14) Un-P1-T2
SPCN connector (J15) Un-P1-T3
SPCN connector (J16) Un-P1-T4
Rack beacon connector Un-P1-T5
Fan 1 Un-A1 Yes
Fan 2 Un-A2 Yes
Fan 3 Un-A3 Yes
Fan 4 Un-A4 Yes
Device physical locations
Disk drive 1 Un-DB1-D01
Disk drive 2 Un-DB1-D02
Disk drive 3 Un-DB1-D03
Disk drive 4 Un-DB1-D04
Disk drive 5 Un-DB1-D05
Disk drive 6 Un-DB1-D06
Disk drive 7 Un-DB2-D07
Disk drive 8 Un-DB2-D08
Disk drive 9 Un-DB2-D09

66 Finding parts, locations, and addresses

Table 21. FRU locations and failing components for the expansion unit (continued)
Failing item name Physical location code Identify LED
Disk drive 10 Un-DB2-D10
Disk drive 11 Un-DB2-D11
Disk drive 12 Un-DB2-D12
Power supply 1 Un-E1
Power supply 2 Un-E2
Disk drive backplane Un-DB1
Disk drive backplane Un-DB2

Notes:
1. J11 is an RPO connection, J14 is an uninterruptible power supply connector, J15 is an SPCN 1
connector, and J16 is an SPCN 2 connector.
2. Multi-adapter bridge domains are labeled PCI Bridge Set inside the expansion unit.
3. The following table provides information necessary to identify the IOP to which an IOA is assigned.
v The left column indicates the domain in which IOA assignment is allowed.
v The right column is used to determine the IOP to which an IOA is assigned.
v The first position in the list must be an IOP. The remaining positions may be IOPs or IOAs. IOAs
are assigned to the first IOP located to their left in the list. Although IOAs can be manually
reassigned using SST/DST, the IOA assignments return to the default order after each IPL.
Table 22. IOA domains and assignments
Multi-adapter bridge domain / PCI bridge set IOA assignments rules
C01 - C04 C01, C02, C03, C04
C06 - C08 C06, C07, C08

5094, 5294, 5096, and 5296

The information provided in this topic defines specific sections of a location code string. Use this
information to understand the meaning of a location code.

Using location codes

Location codes are produced by system firmware to identify replaceable parts. Learn how to read and
understand the sections of a location code string and the comprehensive list of location codes that are
used by the I/O enclosure.

Use the following table to link to a specific topic that you need additional information on when reading
your location code.

Location code topics that might be of interest Description

Location code overview on page 68 Contains background information on the use of location
codes.
Physical location codes on page 68 Provides a definition for physical location code.
Logical location codes on page 68 Provides a definition of what a logical location code is.
Location code format on page 69 Provides descriptive information of the Un value in the
location code string. For example U7879.001.

Finding parts, locations, and addresses 67

Location code topics that might be of interest Description
Location code labels on page 70 Provides a table that identifies and defines the location
code labels. The location code labels begin with an
alphabetic character and follow the system serial number.
For example, U7879.001.10ABCDE-P3-C31-T2-L23. (The
system serial number is the 10ABCDE in the previous
example.) The P3, C31, T2, and L23 all contain an
alphabetic character that is identified in the Location
code labels table.
Worldwide unique identifier on page 70 Provides a definition for the world unique identifier. This
group of digits follows the resource code labels and
always begins with the letter W.

Location code overview

Servers (system unit and expansion units) use Physical location codes to provide mapping of
replaceable units. Location codes are produced by the server's firmware, which structures them so that
they can be used to identify specific parts in a system. The Location code format on page 69 is the
same for all servers.

If you are working with a specific location code, the unit type and model immediately follow the first
character (Utttt.mmm). Match the unit type and model to a link, as shown in the Unit type and locations
table.

If the location code ends with -Txx-Lxx, the server's firmware could not identify the physical location.
When a physical location cannot be identified, a Logical location codes is provided. Where logical
location codes occur in enclosures, the locations topic for the enclosure has the known conversions listed.
For logical location codes with no conversion, contact your next level of support.

If the location code begins with UTMPx, the expansion I/O unit's machine type, model and serial
number have not been set yet and this is a temporary unit identifier. To identify the unit, examine the
display panels on all of the expansion I/O units connected to the server until you find one with the same
characters in the first 5 digits of the top line in the unit's display. Record the unit's real machine type and
model from the unit label. Match the unit's machine type and model in the Unit type and locations table
and follow the link to determine the service information.

Note: Locations for units that are not in the preceding list are either not supported or there is a problem
in the firmware. Contact your next level of support.

Physical location codes

Physical location codes provide a mapping of logical functions and components (such as backplanes,
removable modules, connectors, ports, cables, and devices) to their specific locations within the physical
structure of the server.

Logical location codes

If the physical location cannot be mapped to a physical location code, the server's firmware generates a
logical location code. A logical location code is a sequence of location labels that identifies the path that
the system uses to communicate with a given resource.

Note: A resource has as many logical location codes as it has logical connections to the system. For
example, an external tape device connected to two I/O adapters will have two logical location codes.

An example of a logical location code is:

68 Finding parts, locations, and addresses

U7879.001.10ABCDE-P3-C31-T2-L23

The first part of the location code (through the T2 label) represents the physical location code for the
resource that communicates with the target resource. The remainder of the logical location code (L23)
represents exactly which resource is indicated.

Location code format

The location code is an alphanumeric string of variable length, consisting of a series of location
identifiers, separated by a dash. An example of a physical location for a fan is Un-A1.

The first position, represented by Un (where n is equal to any string contained between the U and the
hyphen) in the preceding example, is displayed in one of the forms in the following table.

Note: In location codes the U is a constant digit; however the numbered positions that follow the U are
variables and are dependent on your server. Each column defines the numbers that follow the U in the
beginning of the location code.

Machine type and model number in its location codes Feature codes and sequence numbers in its location
code

Utttt.mmm.sssssss-A1 Uffff.ccc.sssssss-A1
The leftmost code is always U. The leftmost code is always U.
tttt represents the unit type of the enclosure (drawer or ffff represents the feature code of the enclosure (drawer
node). or node).
mmm represents the model of the enclosure. ccc represents the sequence number of the enclosure .
sssssss represents the serial number for the enclosure. sssssss represents the serial number of the enclosure.
Note: The mmm or ccc number might not be displayed on all location codes for all servers. If the mmm value is not
displayed, the location code is displayed in one of the following forms:
v Utttt.sssssss-A1
v Uffff.sssssss-A1

The location code is hierarchical; that is, each location identifier in the string represents a physical part.
The order (from left to right), in which each identifier is shown, allows you to determine which parts
contain other parts in the string.

The dash (-) separator character represents a relationship between two components in the unit. In the
example of the fan, whose location code is Un-A1, the dash shows that the fan (A1) is contained in the
base unit (or Un). Modules, adapters, cables, and devices are all parts that are plugged into another part.
Their location codes will always show that they are plugged into another part as components of the
server. Another example follows:, Un-P1-C9 is a memory DIMM, with memory DIMM (C9) plugged into
a backplane (P1), which is inside the unit (Un).

For more information about the various location code label prefixes, refer to Location code labels on
page 70.

Note: For devices, certain error conditions might cause an IBM i device to display the device location in
an AIX format.
Table 23. Unit type and locations
Unit type (Utttt.mmm) Link to location information
U5094.001 Locations on page 70
U5096.001 Locations on page 70

Finding parts, locations, and addresses 69

Table 23. Unit type and locations (continued)
Unit type (Utttt.mmm) Link to location information
U5294.001 Locations
U5296.001 Locations

Location code labels

The following table explains what the location code label prefixes mean.

Note: These labels apply to system units only.

Table 24. Location code label prefixes for system units
Prefix Description Example
A Air-moving device Fan, blower
C Card connector IOP, IOA, DIMM, processor card
D Device Diskette, control panel
E Electrical Battery, power supply, ac charger
L Logical path SCSI target IDE address, fibre channel LUN
N Horizontal placement for an empty rack location
P Planar System backplane
T Port
U Unit
V Virtual planar
W Worldwide unique ID
X EIA value for an empty rack location
Y Firmware FRU

Worldwide unique identifier

A worldwide unique identifier location label consists of the prefix W followed by a maximum of 16
uppercase hexadecimal digits with no leading zeros. A location code might not consist of a worldwide
unique identifier. When present, the worldwide unique identifier location label follows the location label
of the resource that interfaces with the resource that has the worldwide unique identifier, usually a port.

Locations
Note:
v The known logical location codes for this unit are listed next to the corresponding physical location in
the following information.
v If you are working with a logical location code for your expansion unit and it is not listed in the
following information, contact your next level of support.

The following diagram shows the FRU layout in the 5094 expansion unit but can be used in conjunction
with the following tables for the 5294, 5096, 5296, expansion units.

Remember: References to disk units, media (optical and tape), and device boards in either the following
diagram or table do not apply to the 5096, or 5296.
If you need address information, refer to 5094, 5294, 5096, and 5296 addresses on page 124.

70 Finding parts, locations, and addresses

Note: Do not install power supplies P00 and P01 ac jumper cables on the same ac module.

The following table gives the components available for callout on the expansion units. It matches those
components with the FRU containing the component. The other columns give location information, a link
to a removal and replacement procedure, and additional comments.
Table 25. FRU locations and failing components for expansion units
Failing item name Symbolic FRU name Physical location code
Expansion unit backplane TWRCARD Un-CB1
v SPCN MA_BRDG
MABRCFG
v Card enclosure or backplane
PPCITWR
v Multi-adapter bridge (all) PRI_PCI
HSL_LNK
PIOCARD
MASBUS
TWRBKPL
TWRPLNR
PCI adapter in slot 1 PIOCARD Un-CB1-C01
MASBUS
SLOTERR
PCI adapter in slot 2 PIOCARD Un-CB1-C02
MASBUS
SLOTERR
PCI adapter in slot 3 PIOCARD Un-CB1-C03
MASBUS
SLOTERR
PCI adapter in slot 4 PIOCARD Un-CB1-C04
MASBUS
SLOTERR

Finding parts, locations, and addresses 71

Table 25. FRU locations and failing components for expansion units (continued)
Failing item name Symbolic FRU name Physical location code
PCI adapter in slot 5 PIOCARD Un-CB1-C05
MASBUS
SLOTERR
PCI adapter in slot 6 PIOCARD Un-CB1-C06
MASBUS
SLOTERR
PCI adapter in slot 7 PIOCARD Un-CB1-C07
MASBUS
SLOTERR
PCI adapter in slot 8 PIOCARD Un-CB1-C08
MASBUS
SLOTERR
PCI adapter in slot 9 PIOCARD Un-CB1-C09
MASBUS
SLOTERR
RIO/HSL adapter card SIIOADP Un-CB1-C10
v HSL I/O adapter SIADPCD
SI_PHB
v PCI host bridge adapter
PCI adapter in slot 11 PIOCARD Un-CB1-C11
MASBUS
SLOTERR
PCI adapter in slot 12 PIOCARD Un-CB1-C12
MASBUS
SLOTERR
PCI adapter in slot 13 PIOCARD Un-CB1-C13
MASBUS
SLOTERR
PCI adapter in slot 14 PIOCARD Un-CB1-C14
MASBUS
SLOTERR
PCI adapter in slot 15 PIOCARD Un-CB1-C15
MASBUS
SLOTERR
PCI bridge set 1 BRDGSET Un-CB1-C01
BRDGST1 Un-CB1-C02
Un-CB1-C03
Un-CB1-C04
PCI bridge set 2 BRDGSET Un-CB1-C05
BRDGST2 Un-CB1-C06
Un-CB1-C07
Un-CB1-C08
Un-CB1-C09
PCI bridge set 3 BRDGSET Un-CB1-C11
BRDGST3 Un-CB1-C12
Un-CB1-C13
Un-CB1-C14
Un-CB1-C15
Fan 1 Un-B01
Fan 2 Un-B02
Power board Un-PB1

72 Finding parts, locations, and addresses

Table 25. FRU locations and failing components for expansion units (continued)
Failing item name Symbolic FRU name Physical location code
AC module 1 Un-A01
AC module 2 Un-A02
Power supply 0 (dual line cord Un-P00
only)
Power supply 1 (single or dual Un-P01
line cord)
Power supply 2 (single or dual Un-P02
line cord)
Power supply 3 (single or dual Un-P03
line cord)
Remember: If you are servicing a 5096, or a 5296 that references to disk units, media (optical and tape), and device
boards in the location tables do not apply to either of these models.
Device board 1 Un-DB1
Device board 2 Un-DB2
Device board 3 Un-DB3
Display panel Un-NB1
Disk units 15 Un-DB1-D01
Un-DB1-D02
Un-DB1-D03
Un-DB1-D04
Un-DB1-D05
Disk units 610 Un-DB2-D06
Un-DB2-D07
Un-DB2-D08
Un-DB2-D09
Un-DB2-D10
Disk units 1115 Un-DB1-D11
Un-DB1-D12
Un-DB1-D13
Un-DB1-D14
Un-DB1-D15
Disk units 1620 Un-DB2-D16
Un-DB2-D17
Un-DB2-D18
Un-DB2-D19
Un-DB2-D20
Disk units 2125 Un-DB1-D21
Un-DB1-D22
Un-DB1-D23
Un-DB1-D24
Un-DB1-D25
Disk units 2630 Un-DB2-D26
Un-DB2-D27
Un-DB2-D28
Un-DB2-D29
Un-DB2-D30

Finding parts, locations, and addresses 73

Table 25. FRU locations and failing components for expansion units (continued)
Failing item name Symbolic FRU name Physical location code
Disk units 3140 Un-DB3-D31
Un-DB3-D32
Un-DB3-D33
Un-DB3-D34
Un-DB3-D35
Un-DB3-D36
Un-DB3-D37
Un-DB3-D38
Un-DB3-D39
Un-DB3-D40
Media (optical) Un-DB3-D41
Media (tape) Un-DB3-D42
Disk units 4650 Un-DB3-D46
Un-DB3-D47
Un-DB3-D48
Un-DB3-D49
Un-DB3-D50
RIO/HSL adapter card connector HSL_LNK Un-CB1-C10-00
HSL2
HSL2_xx
HSLH
HSLH_xx
RIO/HSL adapter card connector HSL_LNK Un-CB1-C10-01
HSL2
HSL2_xx
HSLH
HSLH_xx

Notes:
1. Card positions C01, C05, and C11 are required to be either I/O processors or Integrated xSeries
servers (IXS).
2. J11 is a RPO connection, J14 is an uninterruptible power supply connector, J15 is a SPCN 1 connector,
and J16 is a SPCN 2 connector.
3. Multi-adapter bridge domains are labeled PCI Bridge Set inside the I/O unit.
4. The following table provides information necessary to identify the IOP to which IOAs are assigned.
v The left column indicates the domain in which IOA assignment is allowed.
v The right column is used to determine the IOP to which an IOA is assigned.
v The first position in the list must be an IOP. The remaining positions may be IOPs or IOAs. IOAs
are assigned to the first IOP located to their left in the list. Although IOAs can be manually
reassigned using SST/DST, the IOA assignments return to the default order after each IPL.
Table 26. Identify the IOP to which IOAs are assigned
Multi-adapter bridge domain / PCI bridge set IOA assignment rules
C01 - C04 C01, C02, C03, C04
C05 - C09 C05, C06, C07, C08, C09
C11 - C15 C11, C12, C13, C14, C15

74 Finding parts, locations, and addresses

5786, 5787, 7031-D24, and 7031-T24
The information provided in this topic defines specific sections of a location code string. Use this
information to understand the meaning of a location code.

Using location codes

This topic also provides information about how to read and understand the specific sections of a location
code string. A comprehensive list of location codes used by your I/O enclosure is also provided.

Use the following table to link to a specific topic for additional information when reading and
understanding your location code.
Table 27. Location code topics
Location code topics Description
Location code overview Contains background information about using location
codes.
Physical location codes on page 76 Provides definitions for physical location codes.
Logical location codes on page 76 Provides definitions for logical location codes.
Location code format on page 76 Provides format information of the Un value in the
location code string. For example U7031.001.
Location code labels on page 77 Provides definitions for location code labels. The location
code labels begin with an alphabetic character and follow
the system serial number. For example,
U7031.001.10ABCDE-P3-C31-T2-L23. (The system serial
number is the 10ABCDE.) The P3, C31, T2, and L23 all
contain an alphabetic character that is identified in the
Location code labels table.
Worldwide unique identifier on page 78 Provides definitions for the worldwide unique
identifiers. This group of digits follows the resource code
labels and always begins with the letter W.

Location code overview

Servers (system unit and enclosures) use physical location codes to provide mapping of replaceable units.
Location codes are produced by the server's firmware, which structures them so that they can be used to
identify specific parts in a system. The location code format is the same for all servers.

If you are working with a specific location code, the unit type and model immediately follow the first
character (Utttt.mmm). Match the unit type and model to a link, as shown in the Unit type and locations
table.
v If the location code ends with -Txx-Lxx, the server's firmware could not identify the physical location.
When a physical location cannot be identified, a logical location code is provided. Where logical
location codes occur in enclosures, the locations topic for the enclosure has the known conversions
listed. For logical location codes with no conversion, contact your next level of support.
v If the location code begins with UTMPx, the expansion I/O unit's machine type, model number and
serial number have not been set yet and this is a temporary unit identifier. To identify the unit, do the
following:
1. Examine the display panels on all of the I/O enclosures that are connected to the server until you
find one with the same characters in the first 5 digits of the top line in the enclosure's display.
2. Record the I/O enclosure's real machine type and model from the I/O enclosure label.
3. Match the I/O enclosure's machine type and model in the unit type and locations table and then
follow the link to determine the service information.

Finding parts, locations, and addresses 75

 Note: If you have a location code that does not follow the location code format as described in
Location code format it is either not supported or there is a problem in the firmware. Contact your
next level of support.

Physical location codes

Physical location codes provide a mapping of logical functions and components (such as backplanes,
removable modules, connectors, ports, cables, and devices) to their specific locations within the physical
structure of the server.

Logical location codes

If the physical location cannot be mapped to a physical location code, the server's firmware generates a
logical location code. A logical location code is a sequence of location labels that identifies the path that
the system uses to communicate with a given resource.

A resource has as many logical location codes as it has logical connections to the system. For example, an
external tape device connected to two I/O adapters will have two logical location codes.

An example of a logical location code is:

U7031.001.10ABCDE-P3-C31-T2-L23

The first part of the location code (through the T2 label) represents the physical location code for the
resource that communicates with the target resource. The remainder of the logical location code (L23)
represents exactly which resource is indicated.

Location code format

The location code is an alphanumeric string of variable length, consisting of a series of location
identifiers, separated by a dash. An example of a physical location for a fan is Un-A1.

The first position, represented by Un (where n is equal to any string contained between the U and the
hyphen) in the preceding example, is displayed in one of the forms in the following table.

Note: In location codes, the U is a constant digit. However, the numbered positions following the U are
variables and are dependent on your server. Each row in the following table defines the numbers that
follow the U in the beginning of the location code.

Machine type and model number in its location codes Feature codes and sequence numbers in its location
code

Utttt.mmm.sssssss-A1 Uffff.ccc.sssssss-A1
The leftmost code is always U. The leftmost code is always U.
tttt represents the unit type of the enclosure (drawer or ffff represents the feature code of the enclosure (drawer
node). or node).
mmm represents the model of the enclosure. ccc represents the sequence number of the enclosure .
sssssss represents the serial number for the enclosure. sssssss represents the serial number of the enclosure.
Note: The mmm or ccc number might not be displayed on all location codes for all servers. If the mmm value is not
displayed, the location code is displayed in one of the following forms:
v Utttt.sssssss-A1
v Uffff.sssssss-A1

76 Finding parts, locations, and addresses

The location code is hierarchical; that is, each location identifier in the string represents a physical part.
The order (from left to right), in which each identifier is shown, allows you to determine which parts
contain other parts in the string.

The dash (-) separator character represents a relationship between two components in the unit. In the
example of the fan, whose location code is Un-A1, the dash shows that the fan (A1) is contained in the
base unit (or Un). Modules, adapters, cables, and devices are all parts that are plugged into another part.
Their location codes will always show that they are plugged into another part as components of the
server. Another example follows:, Un-P1-C9 is a memory DIMM, with memory DIMM (C9) plugged into
a backplane (P1), which is inside the unit (Un).

For more information about the various location code label prefixes, refer to Location code labels. To
review a list of location codes for your I/O enclosure, refer to 5786, 5787, 7031-D24, and 7031-T24 on
page 75.

Note: For devices, certain error conditions might cause an IBM i device to display the device location in
an AIX format.
Table 28. Unit type and locations
Unit type (Utttt.mmm) Link to location information
U5786.001 Locations
U5787.001 Locations
U7031.D24 Locations
U7031.T24 Locations

Location code labels

The following table describes the location code label prefixes.

Table 29. Location code label prefixes for I/O enclosure and system units
Prefix Description Example
A Air-moving device Fan, blower
C Card connector input/output port (IOP), input/output adapter
(IOA), dual inline memory module (DIMM),
processor card
D Device Diskette, control panel
E Electrical Battery, power supply, ac charger
L Logical path SCSI target IDE address, fibre channel logical unit number
(LUN)
N Horizontal placement for an empty rack location
P Planar System backplane
T Port System unit or enclosure integrated connector
U Unit Usually consists of the machine type
V Virtual planar
W Worldwide unique ID This group of digits follows the resource code
labels and always begins with the letter W
X Electronic industries alliance (EIA) spacing value Standardized unit of measure used to identify the
for an empty rack location height of a rack drawer or the usable height
space within a rack.

Finding parts, locations, and addresses 77

Table 29. Location code label prefixes for I/O enclosure and system units (continued)
Prefix Description Example
Y Firmware field replaceable unit (FRU) microprogram or instruction set stored in read
only memory (ROM) of your system

Worldwide unique identifier

A worldwide unique identifier location label consists of the prefix W followed by a maximum of 16
uppercase hexadecimal digits with no leading zeros. A location code might not consist of a worldwide
unique identifier. When present, the worldwide unique identifier location label follows the location label
of the resource that interfaces with the resource that has the worldwide unique identifier, usually a port.

Locations
Use the table and illustrations to help you identify the major field replaceable units (FRUs) installed in
your I/O enclosure. The table also will cross reference to the symbolic FRU that might be associated with
each FRU.

Note:
v The known logical location codes for this unit are listed next to the corresponding physical location in
the following information. If you are working with a logical location code for this unit and it is not
listed in the following information, contact your next level of support.
v If you need SCSI repeater card address information, refer to 5786, 5787, 7031-D24, and 7031-T24
addresses on page 130.

The following illustrations show the FRU layout and its associated location code.

Figure 37. I/O enclosure (drawer model, front) or (stand-alone model on its side, front)

78 Finding parts, locations, and addresses

Figure 38. I/O enclosure (drawer model, back)

Finding parts, locations, and addresses 79

Figure 39. I/O enclosure (stand-alone model, back) 7031-T24

Table 30. FRU locations and failing components

Failing item name Physical location code Identify LED
Disk drive backplane 1 Un-P1 No
Disk drive backplane 2 Un-P2 No
Power distribution backplane Un-P3 No
Fan 1 (left) Un-A1 Yes
Fan 2 Un-A2 Yes
Fan 3 (right) Un-A3 Yes
VPD card Un-C1 No
SCSI repeater card 1 (top left) Un-C2 Yes
SCSI repeater card 2 (top right) Un-C3 Yes
SCSI repeater card 3 (bottom left) Un-C4 No
SCSI repeater card 4 (bottom right) Un-C5 Yes
Crossover card 1 (left) Un-C6 No
Crossover card 2 (right) Un-C7 No
Power supply 1 (left) Un-E1 Yes

80 Finding parts, locations, and addresses

Table 30. FRU locations and failing components (continued)
Failing item name Physical location code Identify LED
Rack indicator connector Un-E1-T1 No
Power supply 2 (right) Un-E2 Yes
Rack indicator connector Un-E2-T1 No
Device physical locations
Disk drive 1 (front) Un-P1-D01 (logical location Un-Px- Ty-L5-L0 - Yes
single or Un-Px-Ty-L13-L0 - dual 1)
Disk drive 2 (front) Un-P1-D02 (logical location Un-Px- Ty-L4-L0 - Yes
single or Un-Px-Ty-L12-L0 - dual 1)
Disk drive 3 (front) Un-P1-D03 (logical location Un-Px- Ty-L3-L0 - Yes
single or Un-Px-Ty-L11-L0 - dual 1)
Disk drive 4 (front) Un-P1-D04 (logical location Un-Px- Ty-L2-L0 - Yes
single or Un-Px-Ty-L10-L0 - dual 1)
Disk drive 5 (front) Un-P1-D05 (logical location Un-Px- Ty-L1-L0 - Yes
single or Un-Px-Ty-L9-L0 - dual 1)
Disk drive 6 (front) Un-P1-D06 (logical location Un-Px- Ty-L0-L0 - Yes
single or Un-Px-Ty-L8-L0 - dual 1)
Disk drive 7 (front) Un-P1-D07 (logical location Un-Px- Ty-L5-L0 1) Yes
1
Disk drive 8 (front) Un-P1-D08 (logical location Un-Px- Ty-L4-L0 ) Yes
1
Disk drive 9 (front) Un-P1-D09 (logical location Un-Px- Ty-L3-L0 ) Yes
1
Disk drive 10 (front) Un-P1-D10 (logical location Un-Px- Ty-L2-L0 ) Yes
1
Disk drive 11 (front) Un-P1-D11 (logical location Un-Px- Ty-L1-L0 ) Yes
1
Disk drive 12 (front) Un-P1-D12 (logical location Un-Px- Ty-L0-L0 ) Yes
Disk drive 1 (back) Un-P2-D01 (logical location Un-Px- Ty-L5-L0 - Yes
single or Un-Px-Ty-L13-L0 - dual 1)
Disk drive 2 (back) Un-P2-D02 (logical location Un-Px- Ty-L4-L0 - Yes
single or Un-Px-Ty-L12-L0 - dual 1)
Disk drive 3 (back) Un-P2-D03 (logical location Un-Px- Ty-L3-L0 - Yes
single or Un-Px-Ty-L11-L0 - dual 1)
Disk drive 4 (back) Un-P2-D04 (logical location Un-Px- Ty-L2-L0 - Yes
single or Un-Px-Ty-L10-L0 - dual 1)
Disk drive 5 (back) Un-P2-D05 (logical location Un-Px- Ty-L1-L0 - Yes
single or Un-Px-Ty-L9-L0 - dual 1)
Disk drive 6 (back) Un-P2-D06 (logical location Un-Px- Ty-L0-L0 - Yes
single or Un-Px-Ty-L8-L0 - dual 1)
Disk drive 7 (back) Un-P2-D07 (logical location Un-Px- Ty-L5-L0 1) Yes
1
Disk drive 8 (back) Un-P2-D08 (logical location Un-Px- Ty-L4-L0 ) Yes
1
Disk drive 9 (back) Un-P2-D09 (logical location Un-Px- Ty-L3-L0 ) Yes
1
Disk drive 10 (back) Un-P2-D10 (logical location Un-Px- Ty-L2-L0 ) Yes
1
Disk drive 11 (back) Un-P2-D11 (logical location Un-Px- Ty-L1-L0 ) Yes
1
Disk drive 12 (back) Un-P2-D12 (logical location Un-Px- Ty-L0-L0 ) Yes

Finding parts, locations, and addresses 81

Table 30. FRU locations and failing components (continued)
Failing item name Physical location code Identify LED
1
Where:
v Un-Px is the backplane of the unit where the SCSI PCI adapter is installed.
v Ty is the connector on the SCSI PCI adapter.
v single is a single SCSI interface card.
v dual is a dual SCSI interface card.

5790 and 7311-D11

The information provided in this topic defines specific sections of a location code string. Use this
information to understand the meaning of a location code.

Using location codes

Use the following table to link to a specific topic for additional information when reading and
understanding your location code.
Table 31. Location code topics
Location code topics Description
Location code overview Contains background information about using location
codes.
Physical location codes on page 83 Provides definitions for physical location codes.
Logical location codes on page 83 Provides definitions for logical location codes.
Location code format on page 83 Provides format information of the Un value in the
location code string. For example U7031.001.
Location code labels on page 84 Provides definitions for location code labels. The location
code labels begin with an alphabetic character and follow
the system serial number. For example,
U7031.001.10ABCDE-P3-C31-T2-L23. (The system serial
number is the 10ABCDE.) The P3, C31, T2, and L23 all
contain an alphabetic character that is identified in the
Location code labels table.
Worldwide unique identifier on page 85 Provides definitions for the worldwide unique
identifiers. This group of digits follows the resource code
labels and always begins with the letter W.

Location code overview

Servers (system unit and expansion units) use physical location codes to provide mapping of replaceable
units. Location codes are produced by the server's firmware, which structures them so that they can be
used to identify specific parts in a system. The location code format is the same for all servers.

If you are working with a specific location code, the unit type and model immediately follow the first
character (Utttt.mmm).go
v If the location code ends with -Txx-Lxx, the server's firmware could not identify the physical location.
When a physical location cannot be identified, a logical location code is provided. Where logical
location codes occur in enclosures, the locations topic for the enclosure has the known conversions
listed. For logical location codes with no conversion, contact your next level of support.
v If the location code begins with UTMPx, the expansion I/O unit's machine type, model number and
serial number have not been set yet and this is a temporary unit identifier. To identify the unit, do the
following:

82 Finding parts, locations, and addresses

 1. Examine the display panels on all of the I/O enclosures that are connected to the server until you
find one with the same characters in the first 5 digits of the top line in the enclosure's display.
2. Record the I/O enclosure's real machine type and model from the I/O enclosure label.
3. Match the I/O enclosure's machine type and model in the unit type and locations table and then
follow the link to determine the service information.

Note: If you have a location code that does not follow the location code format as described in
Location code format it is either not supported or there is a problem in the firmware. Contact your
next level of support.

Physical location codes

Physical location codes provide a mapping of logical functions and components (such as backplanes,
removable modules, connectors, ports, cables, and devices) to their specific locations within the physical
structure of the server.

Logical location codes

If the physical location cannot be mapped to a physical location code, the server's firmware generates a
logical location code. A logical location code is a sequence of location labels that identifies the path that
the system uses to communicate with a given resource.

A resource has as many logical location codes as it has logical connections to the system. For example, an
external tape device connected to two I/O adapters will have two logical location codes.

An example of a logical location code is:

U7031.001.10ABCDE-P3-C31-T2-L23

The first part of the location code (through the T2 label) represents the physical location code for the
resource that communicates with the target resource. The remainder of the logical location code (L23)
represents exactly which resource is indicated.

Location code format

The location code is an alphanumeric string of variable length, consisting of a series of location
identifiers, separated by a dash. An example of a physical location for a fan is Un-A1.

The first position, represented by Un (where n is equal to any string contained between the U and the
hyphen) in the preceding example, is displayed in one of the forms in the following table.

Note: In location codes, the U is a constant digit. However, the numbered positions following the U are
variables and are dependent on your server. Each row in the following table defines the numbers that
follow the U in the beginning of the location code.

Machine type and model number in its location codes Feature codes and sequence numbers in its location
code

Utttt.mmm.sssssss-A1 Uffff.ccc.sssssss-A1
The leftmost code is always U. The leftmost code is always U.
tttt represents the unit type of the enclosure (drawer or ffff represents the feature code of the enclosure (drawer
node). or node).
mmm represents the model of the enclosure. ccc represents the sequence number of the enclosure .
sssssss represents the serial number for the enclosure. sssssss represents the serial number of the enclosure.

Finding parts, locations, and addresses 83

Machine type and model number in its location codes Feature codes and sequence numbers in its location
code

Utttt.mmm.sssssss-A1 Uffff.ccc.sssssss-A1
Note: The mmm or ccc number might not be displayed on all location codes for all servers. If the mmm value is not
displayed, the location code is displayed in one of the following forms:
v Utttt.sssssss-A1
v Uffff.sssssss-A1

The location code is hierarchical; that is, each location identifier in the string represents a physical part.
The order (from left to right), in which each identifier is shown, allows you to determine which parts
contain other parts in the string.

The dash (-) separator character represents a relationship between two components in the unit. In the
example of the fan, whose location code is Un-A1, the dash shows that the fan (A1) is contained in the
base unit (or Un). Modules, adapters, cables, and devices are all parts that are plugged into another part.
Their location codes will always show that they are plugged into another part as components of the
server. Another example follows:, Un-P1-C9 is a memory DIMM, with memory DIMM (C9) plugged into
a backplane (P1), which is inside the unit (Un).

For more information about the various location code label prefixes, refer to Location code labels.

Note: For devices, certain error conditions might cause an IBM i device to display the device location in
an AIX format.

Note: For devices, certain error conditions might cause an IBM i device to display the device location in
an AIX format.
Table 32. Unit type and locations
Unit type (Utttt.mmm) Link to location information
U5790.001 Locations
U7311.D11 Locations

Location code labels

The following table describes the location code label prefixes. These labels apply to system units only.
Table 33. Location code label prefixes for system units
Prefix Description Example
A Air-moving device Fan, blower
C Card connector IOP, IOA, DIMM, processor card
D Device Diskette, control panel
E Electrical Battery, power supply, ac charger
L Logical path SCSI target IDE address, fibre channel LUN
N Horizontal placement for an empty rack location
P Planar System backplane
T Port
U Unit
V Virtual planar

84 Finding parts, locations, and addresses

Table 33. Location code label prefixes for system units (continued)
Prefix Description Example
W Worldwide unique ID
X EIA value for an empty rack location
Y Firmware field replaceable unit (FRU)

Worldwide unique identifier

A worldwide unique identifier location label consists of the prefix W followed by a maximum of 16
uppercase hexadecimal digits with no leading zeros. A location code might not consist of a worldwide
unique identifier. When present, the worldwide unique identifier location label follows the location label
of the resource that interfaces with the resource that has the worldwide unique identifier, usually a port.

Locations
Learn how to locate field replaceable units (FRUs) by using logical and physical location codes.

Note: The known logical location codes for this unit are listed next to the corresponding physical location
in the following information. If you are working with a logical location code for this unit and it is not
listed in the following information, contact your next level of support.

The following diagrams show field replaceable unit (FRU) layout in the expansion unit. Use these
diagrams with the following tables.

Note: Some units may have labels that designate location codes other than those shown in the following
illustrations and tables. If that is the case, use the location codes shown in the following illustrations and
tables.

Figure 40. Front view of the expansion unit

Finding parts, locations, and addresses 85

Figure 41. Back view of the expansion unit

The following table gives the components available for callout on the expansion units. It matches those
components with the FRU containing the component. The other columns give location information, a link
to a removal and replacement procedure, and additional information.
Table 34. FRU locations and failing components
Failing item name Physical location code Identify LED
Expansion unit Un
Fan
Fan Un-A1 Yes
Power supplies
Power supply 1 Un-E1 Yes
Power supply 2 Un-E2 Yes
Backplane
I/O backplane Un-P1 Yes
I/O backplane ports
Rack beacon connector Un-P1-T1
Adapters
PCI adapter in slot 1 Un-P1-C1 Yes
PCI adapter in slot 2 Un-P1-C2 Yes
PCI adapter in slot 3 Un-P1-C3 Yes
PCI adapter in slot 4 Un-P1-C4 Yes
PCI adapter in slot 5 Un-P1-C5 Yes
PCI adapter in slot 6 Un-P1-C6 Yes
PCI bridge set 1 Un-P1
Un-P1-C1
Un-P1-C2
Un-P1-C3
PCI bridge set 2 Un-P1
Un-P1-C4
Un-P1-C5
Un-P1-C6
RIO/HSL adapter Un-P1-C7 Yes

86 Finding parts, locations, and addresses

Table 34. FRU locations and failing components (continued)
Failing item name Physical location code Identify LED
RIO/HSL adapter connector (top Un-P1-C7-00 Yes
connector), port 0 or
Un-P1-C7-T1
RIO/HSL adapter connector (bottom Un-P1-C7-01 Yes
connector), port 1 or
Un-P1-C7-T2

5791, 5794, 5797, and 5798

The information provided in this topic defines specific sections of a location code string. Use this
information to understand the meaning of a location code.

Using location codes

For additional information about reading your location code, use the following table to link to a specific
topic.

Location code topics that might be of interest Description

Location code overview Contains background information on the use of location
codes.
Physical location codes on page 88 Provides a definition for physical location code.
Logical location codes on page 88 Provides a definition for a logical location code.
Location code format on page 88 Provides descriptive information of the Un value in the
location code string. For example U5886.001.
Location code labels on page 89 Provides a table that identifies and defines the location
code labels. The location code labels begin with an
alphabetic character and follow the system serial number.
For example, U7879.001.10ABCDE-P3-C31-T2-L23. (The
system serial number is the 10ABCDE in the previous
example.) The P3, C31, T2, and L23 all contain an
alphabetic character that is identified in the Location
code labels table.
Worldwide unique identifier on page 90 Provides a definition for the worldwide unique identifier.
This group of digits follows the resource code labels and
always begins with the letter W.

Location code overview

Servers (system unit and expansion units) use physical location codes to provide mapping of replaceable
units. Location codes are produced by the server's firmware, which structures them so that they can be
used to identify specific parts in a system. The location code format is the same for all servers.

If you are working with a specific location code, the feature immediately follows the first character
(U5886). Refer to the Unit type and locations table.

If the location code ends with -Txx-Lxx, the server's firmware could not identify the physical location.
When a physical location cannot be identified, a logical location code is provided. Where logical location
codes occur in enclosures, the locations topic for the enclosure has the known conversions listed. For
logical location codes with no conversion, contact your next level of support.

Finding parts, locations, and addresses 87

If the location code begins with UTMPx, the expansion I/O unit's machine type, model and serial
number have not been set yet and this is a temporary unit identifier. To identify the unit, examine the
display panels on all of the expansion I/O units connected to the server until you find one with the same
characters in the first 5 digits of the top line in the unit's display. Record the unit's real machine type and
model from the unit label. Match the unit's machine type and model in the Unit type and locations table,
and follow the link to determine the service information.

Note: If locations for units are not in the preceding format, either they are not supported or there is a
problem in the firmware. Contact your next level of support.

Physical location codes

Physical location codes provide a mapping of logical functions and components (such as backplanes,
removable modules, connectors, ports, cables, and devices) to their specific locations within the physical
structure of the server.

Logical location codes

If the physical location cannot be mapped to a physical location code, the server's firmware generates a
logical location code. A logical location code is a sequence of location labels that identifies the path that
the system uses to communicate with a given resource.

Note: A resource has as many logical location codes as it has logical connections to the system. For
example, an external tape device connected to two I/O adapters will have two logical location codes.

An example of a logical location code is:

U7879.001.10ABCDE-P3-C31-T2-L23

The first part of the location code (through the T2 label) represents the physical location code for the
resource that communicates with the target resource. The remainder of the logical location code (L23)
represents exactly which resource is indicated.

Location code format

The location code is an alphanumeric string of variable length, consisting of a series of location
identifiers, separated by a dash. An example of a physical location for a fan is Un-A1.

The first position, represented by Un (where n is equal to any string contained between the U and the
hyphen) in the preceding example, is displayed in one of the forms in the following table.

Note: In location codes, the U is a constant digit; however, the numbered positions following the U are
variables and are dependent on your server. Each column defines the numbers that follow the U in the
beginning of the location code.

Machine type and model number in its location codes Feature codes and sequence numbers in its location
code

Utttt.mmm.sssssss-A1 Uffff.ccc.sssssss-A1
The leftmost code is always U. The leftmost code is always U.
tttt represents the unit type of the enclosure (drawer or ffff represents the feature code of the enclosure (drawer
node). or node).
mmm represents the model of the enclosure. ccc represents the sequence number of the enclosure .
sssssss represents the serial number for the enclosure. sssssss represents the serial number of the enclosure.

88 Finding parts, locations, and addresses

Machine type and model number in its location codes Feature codes and sequence numbers in its location
code

Utttt.mmm.sssssss-A1 Uffff.ccc.sssssss-A1
Note: The mmm or ccc number might not be displayed on all location codes for all servers. If the mmm value is not
displayed, the location code is displayed in one of the following forms:
v Utttt.sssssss-A1
v Uffff.sssssss-A1

The location code is hierarchical; that is, each location identifier in the string represents a physical part.
The order (from left to right), in which each identifier is shown, allows you to determine which parts
contain other parts in the string.

The dash (-) separator character represents a relationship between two components in the unit. In the
example of the fan, whose location code is Un-A1, the dash shows that the fan (A1) is contained in the
base unit (or Un). Modules, adapters, cables, and devices are all parts that are plugged into another part.
Their location codes will always show that they are plugged into another part as components of the
server. Another example follows:, Un-P1-C9 is a memory DIMM, with memory DIMM (C9) plugged into
a backplane (P1), which is inside the unit (Un).

For more information about the various location code label prefixes, refer to Location code labels.

Note: For devices, certain error conditions might cause an IBM i device to display the device location in
an AIX format.
Table 35. Unit type and locations
Unit type (Utttt.mmm) Link to location information
U5791 Refer to Locations in order to differentiate between the 5791, 5794, 5797, and 5798.

Location code labels

The following table identifies the location code label prefixes.

Note: These labels apply to system units only.

Table 36. Location code label prefixes for system units
Prefix Description Example
A Air-moving device Fan, blower
C Card connector IOP, IOA, DIMM, processor card
D Device Diskette, control panel
E Electrical Battery, power supply, ac charger
L Logical path SAS target IDE address, fibre channel LUN
N Horizontal placement for an empty rack location
P Planar System backplane
T Port
U Unit
V Virtual planar
W Worldwide unique ID
X EIA value for an empty rack location

Finding parts, locations, and addresses 89

Table 36. Location code label prefixes for system units (continued)
Prefix Description Example
Y Firmware FRU

Worldwide unique identifier

A worldwide unique identifier location label consists of the prefix W followed by a maximum of 16
uppercase hexadecimal digits with no leading zeros. A location code might not consist of a worldwide
unique identifier. When present, the worldwide unique identifier location label follows the location label
of the resource that interfaces with the resource that has the worldwide unique identifier, usually a port.

Locations
Use this information to help you map a location code to a position on the unit.

Note: The known logical location codes for this unit are listed next to the corresponding physical location
in the following information. If you are working with a logical location code for this unit and it is not
listed in the following information, contact your next level of support.

The following diagrams show the field replaceable unit (FRU) layout in the system. Use these diagrams
with the following tables.

Important: The current design for the 5794, 5797 and 5798 have the VPD same 5791 label. To help you
differentiate the differences refer to these characteristics:
v Differences between FC5791 and FC5794:
v
5791 (4 drive backplanes for 16 drives) has P3 (furthest left), P4, P5, and P6 (furthest right) drive
bays contain drives and drive backplanes.
5794 (2 drive backplanes for 8 disks) has only P3 (furthest left) and P5 drive bays contain drives and
drive backplanes.
v Differences between 5797 (with repeater card) and 5798 (without repeater card) :
v
Includes imbedded SCSI controllers: P1-T4, P1-T5, P2-T4, P2-T5 (T4 and T5)

90 Finding parts, locations, and addresses

Figure 42. 5791 and 5794 front view

Figure 43. 5791 and 5794 back view

Finding parts, locations, and addresses 91

Figure 44. 5797 and 5798 front view

Figure 45. 5797 and 5798 back view

92 Finding parts, locations, and addresses

Figure 46. Top view

The following table provides location codes for parts that make up the server.

The 5791 RIO cable has black connectors and does not have the letters RSR or RLR on the label. The 5797
has the letters RLR on the label, and the 12X cable has green connectors. The 5798 has the letters RSR on
the label, and the 12X cable has green connectors.
Table 37. 5791 and 5794 location codes
Failing item name Physical location code
I/O planar book, plugs into I/O backplane Un-P1
I/O planar book, plugs into I/O backplane Un-P2
Disk drive backplane Un-P3
Disk drive backplane Un-P4
Disk drive backplane Un-P5
Disk drive backplane Un-P6
PCI adapter in slot 1 Un-P1-C01
PCI adapter in slot 2 Un-P1-C02
PCI adapter in slot 3 Un-P1-C03
PCI adapter in slot 4 Un-P1-C04
PCI adapter in slot 5 Un-P1-C05
PCI adapter in slot 6 Un-P1-C06
PCI adapter in slot 7 Un-P1-C07
PCI adapter in slot 8 Un-P1-C08
PCI adapter in slot 9 Un-P1-C09
PCI adapter in slot 10 Un-P1-C10
IB riser card Un-P1-C11
IB riser card Un-P1-C11-T1
IB riser card Un-P1-C11-T2

Finding parts, locations, and addresses 93

Table 37. 5791 and 5794 location codes (continued)
PHB (PCI bridge set) 1 Un-P1-C01

Un-P1-C02

Un-P1-C03

Un-P1-C04
PHB (PCI bridge set) 2 Un-P1-C05

Un-P1-C06

Un-P1-C07
PHB (PCI bridge set) 3 Un-P1-C08

Un-P1-C09

Un-P1-C10
PCI adapter in slot 1 Un-P2-C01
PCI adapter in slot 2 Un-P2-C02
PCI adapter in slot 3 Un-P2-C03
PCI adapter in slot 4 Un-P2-C04
PCI adapter in slot 5 Un-P2-C05
PCI adapter in slot 6 Un-P2-C06
PCI adapter in slot 7 Un-P2-C07
PCI adapter in slot 8 Un-P2-C08
PCI adapter in slot 9 Un-P2-C09
PCI adapter in slot 10 Un-P2-C10
PHB (PCI bridge set) 1 Un-P2-C01

Un-P2-C02

Un-P2-C03

Un-P2-C04
PHB (PCI bridge set) 2 Un-P2-C05

Un-P2-C06

Un-P2-C07
PHB (PCI bridge set) 3 Un-P2-C08

Un-P2-C09

Un-P2-C10
Fan 1 (left) Un-A1
Fan 2 Un-A2
Fan 3 Un-A3
Fan 4 (right) Un-A4
Power supply 1 (left) Un-E1

94 Finding parts, locations, and addresses

Table 37. 5791 and 5794 location codes (continued)
Super UPIC connector (left) Un-E1-T1
Super UPIC connector (right) Un-E1-T2
Power supply 2 (right) Un-E2
Super UPIC connector (left) Un-E2-T1
Super UPIC connector (right) Un-E2-T2
12X adapter connector port 0 (bottom connector - P0) Un-P1-00
12X adapter connector port 1 (top conector - P1) Un-P1-01
12X adapter connector port 0 (bottom connector - P0) Un-P2-00
12X adapter connector port 1 (top conector - P1) Un-P2-01
Media subsystem power connector Un-P1-T3
Media subsystem power connector Un-P2-T3
Integrated SCSI controller port Un-P1-T5
Integrated SCSI controller port Un-P1-T6
Integrated SCSI controller port Un-P2-T5
Integrated SCSI controller port Un-P2-T6

The following table provides location codes for parts that make up the server.
Table 38. 5797 and 5798 location codes
Failing item name Physical location code
I/O planar book, plugs into I/O backplane Un-P1
I/O planar book, plugs into I/O backplane Un-P2
Disk drive backplane Un-P3
Disk drive backplane Un-P4
Disk drive backplane Un-P5
Disk drive backplane Un-P6
PCI adapter in slot 1 Un-P1-C1
PCI adapter in slot 2 Un-P1-C2
PCI adapter in slot 3 Un-P1-C3
PCI adapter in slot 4 Un-P1-C4
PCI adapter in slot 5 Un-P1-C5
PCI adapter in slot 6 Un-P1-C6
PCI adapter in slot 7 Un-P1-C7
PCI adapter in slot 8 Un-P1-C8
PCI adapter in slot 9 Un-P1-C9
PCI adapter in slot 10 Un-P1-C10
PHB (PCI bridge set) 1 Un-P1-C1

Un-P1-C2

Un-P1-C3

Un-P1-C4

Finding parts, locations, and addresses 95

Table 38. 5797 and 5798 location codes (continued)
PHB (PCI bridge set) 2 Un-P1-C5

Un-P1-C6

Un-P1-C7
PHB (PCI bridge set) 3 Un-P1-C8

Un-P1-C9

Un-P1-C10
PCI adapter in slot 1 Un-P2-C1
PCI adapter in slot 2 Un-P2-C2
PCI adapter in slot 3 Un-P2-C3
PCI adapter in slot 4 Un-P2-C4
PCI adapter in slot 5 Un-P2-C5
PCI adapter in slot 6 Un-P2-C6
PCI adapter in slot 7 Un-P2-C7
PCI adapter in slot 8 Un-P2-C8
PCI adapter in slot 9 Un-P2-C9
PCI adapter in slot 10 Un-P2-C10
IB riser port Un-Px-T2
IB riser port Un-Px-T1
PHB (PCI bridge set) 1 Un-P2-C1

Un-P2-C2

Un-P2-C3

Un-P2-C4
PHB (PCI bridge set) 2 Un-P2-C5

Un-P2-C6

Un-P2-C7
PHB (PCI bridge set) 3 Un-P2-C8

Un-P2-C9

Un-P2-C10
Fan 1 (left) Un-A1
Fan 2 Un-A2
Fan 3 Un-A3
Fan 4 (right) Un-A4
Power supply 1 (left) Un-E1
Super UPIC connector (left) Un-E1-T1
Super UPIC connector (right) Un-E1-T2
Power supply 2 (right) Un-E2
Super UPIC connector (left) Un-E2-T1

96 Finding parts, locations, and addresses

Table 38. 5797 and 5798 location codes (continued)
Super UPIC connector (right) Un-E2-T2
12X attachment top port Un-P1-T1
12X attachment bottom port Un-P1-T2
Media bay power connector Un-P1-T3
Media bay power connector Un-P2-T3
Integrated SCSI controller port Un-P1-T4
Integrated SCSI controller port Un-P1-T5
Integrated SCSI controller port Un-P2-T4
Integrated SCSI controller port Un-P2-T5

5796 and 7314-G30

The information provided in this topic defines specific sections of a location code string. Use this
information to understand the meaning of a location code.

Using location codes

Use the following table to link to a specific topic that you need additional information on when reading
your location code.
Table 39. Location code topics
Location code topics Description
Location code overview Contains background information on the use of location
codes.
Physical location codes on page 98 Provides a definition for physical location code.
Logical location codes on page 98 Provides a definition of what a logical location code is.
Location code format on page 98 Provides descriptive information of the Un value in the
location code string. For example, U7879.001.
Location code labels on page 99 Provides a table that identifies and defines the location
code labels. The location code labels begin with an
alphabetic character and follow the system serial number.
For example, U7879.001.10ABCDE-P3-C31-T2-L23. (The
system serial number is the 10ABCDE in the previous
example.) The P3, C31, T2, and L23 all contain an
alphabetic character that is identified in the Location
code labels table.
Worldwide unique identifier on page 100 Provides a definition of a worldwide unique identifier.
This group of digits follows the resource code labels and
always begins with the letter W.

Location code overview

Servers (system unit and expansion units) use physical location codes to provide mapping of replaceable
units. Location codes are produced by the server's firmware, which structures them so that they can be
used to identify specific parts in a system. The location code format is the same for all servers.

If you are working with a specific location code, the unit type and model immediately follow the first
character (Utttt.mmm). Match the unit type and model to a link, as shown in the Unit type and locations
table.

Finding parts, locations, and addresses 97

If the location code ends with -Txx-Lxx, the server's firmware could not identify the physical location.
When a physical location cannot be identified, a logical location code is provided. Where logical location
codes occur in enclosures, the locations topic for the enclosure has the known conversions listed. For
logical location codes with no conversion, contact your next level of support.

If the location code begins with UTMPx, the expansion I/O unit's machine type, model and serial
number have not been set yet and this is a temporary unit identifier. To identify the unit, examine the
display panels on all of the expansion I/O units connected to the server until you find one with the same
characters in the first 5 digits of the top line in the unit's display. If the expansion unit does not have a
display, use the display of the attached system unit, or use the process of elimination by tracing the
cables from the system unit to the expansion unit. Record the unit's machine type and model from the
unit label. Match the unit's machine type and model in the Unit type and locations table and follow the
link to determine the service information.

Note: Locations for units that are not in the preceding list are either not supported or there is a problem
in the firmware. Contact your next level of support.

Physical location codes

Physical location codes provide a mapping of logical functions and components (such as backplanes,
removable modules, connectors, ports, cables, and devices) to their specific locations within the physical
structure of the server.

Logical location codes

If the physical location cannot be mapped to a physical location code, the server's firmware generates a
logical location code. A logical location code is a sequence of location labels that identifies the path that
the system uses to communicate with a given resource.

Note: A resource has as many logical location codes as it has logical connections to the system. For
example, an external tape device connected to two I/O adapters will have two logical location codes.

An example of a logical location code is:

U7879.001.10ABCDE-P3-C31-T2-L23

The first part of the location code (through the T2 label) represents the physical location code of the
resource that communicates with the target resource. The remainder of the logical location code (L23)
represents exactly which resource is indicated.

Location code format

The location code is an alphanumeric string of variable length, consisting of a series of location
identifiers, separated by a dash. An example of a physical location for a fan is Un-A1.

The first position, represented by Un (where n is equal to any string contained between the U and the
hyphen) in the preceding example, is displayed in one of the forms in the following table.

Note: In location codes, the U is a constant digit; however, the numbered positions following the U are
variables and are dependent on your server. Each column defines the numbers that follow the U in the
beginning of the location code.

Machine type and model number in its location codes Feature codes and sequence numbers in its location
code

Utttt.mmm.sssssss-A1 Uffff.ccc.sssssss-A1
The leftmost code is always U. The leftmost code is always U.

98 Finding parts, locations, and addresses

Machine type and model number in its location codes Feature codes and sequence numbers in its location
code

Utttt.mmm.sssssss-A1 Uffff.ccc.sssssss-A1
tttt represents the unit type of the enclosure (drawer or ffff represents the feature code of the enclosure (drawer
node). or node).
mmm represents the model of the enclosure. ccc represents the sequence number of the enclosure .
sssssss represents the serial number for the enclosure. sssssss represents the serial number of the enclosure.
Note: The mmm or ccc number might not be displayed on all location codes for all servers. If the mmm value is not
displayed, the location code is displayed in one of the following forms:
v Utttt.sssssss-A1
v Uffff.sssssss-A1

The location code is hierarchical; that is, each location identifier in the string represents a physical part.
The order (from left to right), in which each identifier is shown, allows you to determine which parts
contain other parts in the string.

The dash (-) separator character represents a relationship between two components in the unit. In the
example of the fan, whose location code is Un-A1, the dash shows that the fan (A1) is contained in the
base unit (or Un). Modules, adapters, cables, and devices are all parts that are plugged into another part.
Their location codes will always show that they are plugged into another part as components of the
server. Another example follows:, Un-P1-C9 is a dual in-line memory module (DIMM), with memory
DIMM (C9) plugged into a backplane (P1), which is inside the unit (Un).

For more information about the various location code label prefixes, refer to Location code labels.

Note: For devices, certain error conditions might cause an IBM i device to display the device location in
an AIX format.
Table 40. Unit type and locations
Unit type (Utttt.mmm) Link to location information
U5796.001 Locations on page 100
U7314.G30 Locations on page 100

Location code labels

The following table describes the location code label prefixes.

Note: These location code labels apply to system units only.

Table 41. Location code label prefixes for system units
Prefix Description Example
A Air-moving device Fan, blower
C Card connector IOP, IOA, DIMM, processor card
D Device Diskette, control panel
E Electrical Battery, power supply, ac charger
L Logical path SCSI target IDE address, fibre channel LUN
N Horizontal placement for an empty rack location
P Planar System backplane

Finding parts, locations, and addresses 99

Table 41. Location code label prefixes for system units (continued)
Prefix Description Example
T Port
U Unit
V Virtual planar
W Worldwide unique ID
X EIA value for an empty rack location
Y Firmware FRU

Worldwide unique identifier

A worldwide unique identifier location label consists of the prefix W followed by a maximum of 16
uppercase hexadecimal digits with no leading zeros. A location code might not include a worldwide
unique identifier. When present, the worldwide unique identifier location label follows the location label
of the resource that interfaces with the resource that has the worldwide unique identifier, usually a port.

Locations
The known logical location codes for this unit are listed next to the corresponding physical location.

Note: Any known logical location codes for this unit are listed next to the corresponding physical
location in the following information. If you are working with a logical location code for this unit and it
is not listed in the following information, contact your next level of support.

Figure 47. Rear view of unit.

100 Finding parts, locations, and addresses

Figure 48. Front view of unit.

The following table provides location codes for parts that comprise the server.
Table 42. FRU locations and failing components
Failing item name Symbolic failing item Physical location code Identify LED
name
System unit Un
Power supplies
Power supply 1, from Un-E1 Yes
front view it is left
Power supply 2, from Un-E2 Yes
front view it is right
Backplane
I/O planar Un-P1 Yes
Adapters
PCI adapter in slot 1 Un-P1-C1 Yes
PCI adapter in slot 2 Un-P1-C2 Yes
PCI adapter in slot 3 Un-P1-C3 Yes
PCI adapter in slot 4 Un-P1-C4 Yes
PCI adapter in slot 5 Un-P1-C5 Yes
PCI adapter in slot 6 Un-P1-C6 Yes
GX Dual-Port 12X Channel Un-P1-C7 Yes
Attach adapter
GX Dual-Port 12X Channel Un-P1-C7-T1 Yes
Attach adapter top port
GX Dual-Port 12X Channel Un-P1-C7-T2 Yes
Attach adapter bottom
port
SPCN Un-P1-C8
SPCN top port Un-P1-C8-T1
SPCN bottom port Un-P1-C8-T2

Finding parts, locations, and addresses 101

5802 and 5877
The information provided in this topic defines specific sections of a location code string. Use this
information to understand the meaning of a location code.

Using location codes

For additional information about reading your location code, use the following table to link to a specific
topic.

Location code topics that might be of interest Description

Location code overview Contains background information on the use of location
codes.
Physical location codes on page 103 Provides a definition for physical location code.
Logical location codes on page 103 Provides a definition for a logical location code.
Location code format on page 103 Provides descriptive information of the Un value in the
location code string. For example U5886.001.
Location code labels on page 104 Provides a table that identifies and defines the location
code labels. The location code labels begin with an
alphabetic character and follow the system serial number.
For example, U7879.001.10ABCDE-P3-C31-T2-L23. (The
system serial number is the 10ABCDE in the previous
example.) The P3, C31, T2, and L23 all contain an
alphabetic character that is identified in the Location
code labels table.
Worldwide unique identifier on page 104 Provides a definition for the worldwide unique identifier.
This group of digits follows the resource code labels and
always begins with the letter W.

Location code overview

Servers (system unit and expansion units) use physical location codes to provide mapping of replaceable
units. Location codes are produced by the server's firmware, which structures them so that they can be
used to identify specific parts in a system. The location code format is the same for all servers.

If you are working with a specific location code, the feature immediately follows the first character
(U5886). Refer to the Unit type and locations table.

If the location code ends with -Txx-Lxx, the server's firmware could not identify the physical location.
When a physical location cannot be identified, a logical location code is provided. Where logical location
codes occur in enclosures, the locations topic for the enclosure has the known conversions listed. For
logical location codes with no conversion, contact your next level of support.

If the location code begins with UTMPx, the expansion I/O unit's machine type, model and serial
number have not been set yet and this is a temporary unit identifier. To identify the unit, examine the
display panels on all of the expansion I/O units connected to the server until you find one with the same
characters in the first 5 digits of the top line in the unit's display. Record the unit's real machine type and
model from the unit label. Match the unit's machine type and model in the Unit type and locations table,
and follow the link to determine the service information.

Note: If locations for units are not in the preceding format, either they are not supported or there is a
problem in the firmware. Contact your next level of support.

102 Finding parts, locations, and addresses

Physical location codes

Physical location codes provide a mapping of logical functions and components (such as backplanes,
removable modules, connectors, ports, cables, and devices) to their specific locations within the physical
structure of the server.

Logical location codes

If the physical location cannot be mapped to a physical location code, the server's firmware generates a
logical location code. A logical location code is a sequence of location labels that identifies the path that
the system uses to communicate with a given resource.

Note: A resource has as many logical location codes as it has logical connections to the system. For
example, an external tape device connected to two I/O adapters will have two logical location codes.

An example of a logical location code is:

U7879.001.10ABCDE-P3-C31-T2-L23

The first part of the location code (through the T2 label) represents the physical location code for the
resource that communicates with the target resource. The remainder of the logical location code (L23)
represents exactly which resource is indicated.

Location code format

The location code is an alphanumeric string of variable length, consisting of a series of location
identifiers, separated by a dash. An example of a physical location for a fan is Un-A1.

The first position, represented by Un (where n is equal to any string contained between the U and the
hyphen) in the preceding example, is displayed in one of the forms in the following table.

Note: In location codes, the U is a constant digit; however, the numbered positions following the U are
variables and are dependent on your server. Each column defines the numbers that follow the U in the
beginning of the location code.

Machine type and model number in its location codes Feature codes and sequence numbers in its location
code

Utttt.mmm.sssssss-A1 Uffff.ccc.sssssss-A1
The leftmost code is always U. The leftmost code is always U.
tttt represents the unit type of the enclosure (drawer or ffff represents the feature code of the enclosure (drawer
node). or node).
mmm represents the model of the enclosure. ccc represents the sequence number of the enclosure .
sssssss represents the serial number for the enclosure. sssssss represents the serial number of the enclosure.
Note: The mmm or ccc number might not be displayed on all location codes for all servers. If the mmm value is not
displayed, the location code is displayed in one of the following forms:
v Utttt.sssssss-A1
v Uffff.sssssss-A1

The location code is hierarchical; that is, each location identifier in the string represents a physical part.
The order (from left to right), in which each identifier is shown, allows you to determine which parts
contain other parts in the string.

The dash (-) separator character represents a relationship between two components in the unit. In the
example of the fan, whose location code is Un-A1, the dash shows that the fan (A1) is contained in the

Finding parts, locations, and addresses 103

base unit (or Un). Modules, adapters, cables, and devices are all parts that are plugged into another part.
Their location codes will always show that they are plugged into another part as components of the
server. Another example follows:, Un-P1-C9 is a memory DIMM, with memory DIMM (C9) plugged into
a backplane (P1), which is inside the unit (Un).

For more information about the various location code label prefixes, refer to Location code labels.

Note: For devices, certain error conditions might cause an IBM i device to display the device location in
an AIX format.
Table 43. Unit type and locations
Unit type (Utttt.mmm) Link to location information
U5802.001 Locations
U5877.001 Locations

Location code labels

The following table identifies the location code label prefixes.

Note: These labels apply to system units only.

Table 44. Location code label prefixes for system units
Prefix Description Example
A Air-moving device Fan, blower
C Card connector IOP, IOA, DIMM, processor card
D Device Diskette, control panel
E Electrical Battery, power supply, ac charger
L Logical path SAS target IDE address, fibre channel LUN
N Horizontal placement for an empty rack location
P Planar System backplane
T Port
U Unit
V Virtual planar
W Worldwide unique ID
X EIA value for an empty rack location
Y Firmware FRU

Worldwide unique identifier

A worldwide unique identifier location label consists of the prefix W followed by a maximum of 16
uppercase hexadecimal digits with no leading zeros. A location code might not consist of a worldwide
unique identifier. When present, the worldwide unique identifier location label follows the location label
of the resource that interfaces with the resource that has the worldwide unique identifier, usually a port.

Locations
Use this information to help you map a location code to a position on the unit.

104 Finding parts, locations, and addresses

Note: The known logical location codes for this unit are listed next to the corresponding physical location
in the following information. If you are working with a logical location code for this unit and it is not
listed in the following information, contact your next level of support.

The following diagrams show the field replaceable unit (FRU) layout in the system. Use these diagrams
with the following tables.

Figure 49. 5802 front view

Figure 50. 5802 rear view

Finding parts, locations, and addresses 105

Figure 51. 5877 front view

Figure 52. 5877 rear view

The following table provides location codes for parts that make up the server.
Table 45. Bulk power assembly (BPA) locations, and failing components
Failing item name Symbolic FRU name CCIN
OCA Ux-E1 2C43
OCA UPIC connector Ux-E1-T1
OCA UPIC connector Ux-E1-T2
OCA Ux-E2 2C43
OCA UPIC connector Ux-E2-T1
OCA UPIC connector Ux-E2-T2
Fans
Fan Ux-E1-A1
Fan Ux-E1-A2
Fan Ux-E2-A1
Fan Ux-E2-A2
Backplane

106 Finding parts, locations, and addresses

Table 45. Bulk power assembly (BPA) locations, and failing components (continued)
Failing item name Symbolic FRU name CCIN
Planar Ux-P1 50A2
IOA slot Ux-P1-C1
IOA slot Ux-P1-C2
IOA slot Ux-P1-C3
IOA slot Ux-P1-C4
IOA slot Ux-P1-C5
IOA slot Ux-P1-C6
IOA slot Ux-P1-C7
IOA slot Ux-P1-C8
IOA slot Ux-P1-C9
IOA slot Ux-P1-C10
IB riser port Ux-P1-T1
IB riser port Ux-P1-T2
EMC card
EMC card Ux-P2 50A6
UPS Ux-P2-T1
SPCN 9 pin D-shell Ux-P2-T2
SPCN 9 pin D-shell Ux-P2-T3
DASD
DASD backplane Ux-P3 50A9
PORT card 1 Ux-P3-C1 50A4
PORT card 2 Ux-P3-C2 50A4
PORT card 3 Ux-P3-C3 50A4
PORT card 4 Ux-P3-C4 50A4
DASD drive bay Ux-P3-D1
DASD drive bay Ux-P3-D2
DASD drive bay Ux-P3-D3
DASD drive bay Ux-P3-D4
DASD drive bay Ux-P3-D5
DASD drive bay Ux-P3-D6
DASD drive bay Ux-P3-D7
DASD drive bay Ux-P3-D8
DASD drive bay Ux-P3-D9
DASD drive bay Ux-P3-D10
DASD drive bay Ux-P3-D11
DASD drive bay Ux-P3-D12
DASD drive bay Ux-P3-D13
DASD drive bay Ux-P3-D14
DASD drive bay Ux-P3-D15
DASD drive bay Ux-P3-D16

Finding parts, locations, and addresses 107

Table 45. Bulk power assembly (BPA) locations, and failing components (continued)
Failing item name Symbolic FRU name CCIN
DASD drive bay Ux-P3-D17
DASD drive bay Ux-P3-D18
SAS conduit
SAS conduit Ux-P4 50A5
SAS connector Ux-P4-T1
SAS connector Ux-P4-T2
SAS connector Ux-P4-T3
SAS connector Ux-P4-T4
Media bay connector Ux-P4-T5
Midplane
Midplane Ux-P5 50AA

5803 and 5873

The information provided in this topic defines specific sections of a location code string. Use this
information to understand the meaning of a location code.

Using location codes

For additional information about reading your location code, use the following table to link to a specific
topic.

Location code topics that might be of interest Description

Location code overview Contains background information on the use of location
codes.
Physical location codes on page 109 Provides a definition for physical location code.
Logical location codes on page 109 Provides a definition for a logical location code.
Location code format on page 109 Provides descriptive information of the Un value in the
location code string. For example U5886.001.
Location code labels on page 110 Provides a table that identifies and defines the location
code labels. The location code labels begin with an
alphabetic character and follow the system serial number.
For example, U7879.001.10ABCDE-P3-C31-T2-L23. (The
system serial number is the 10ABCDE in the previous
example.) The P3, C31, T2, and L23 all contain an
alphabetic character that is identified in the Location
code labels table.
Worldwide unique identifier on page 111 Provides a definition for the worldwide unique identifier.
This group of digits follows the resource code labels and
always begins with the letter W.

Location code overview

Servers (system unit and expansion units) use physical location codes to provide mapping of replaceable
units. Location codes are produced by the server's firmware, which structures them so that they can be
used to identify specific parts in a system. The location code format is the same for all servers.

108 Finding parts, locations, and addresses

If you are working with a specific location code, the feature immediately follows the first character
(U5886). Refer to the Unit type and locations table.

If the location code ends with -Txx-Lxx, the server's firmware could not identify the physical location.
When a physical location cannot be identified, a logical location code is provided. Where logical location
codes occur in enclosures, the locations topic for the enclosure has the known conversions listed. For
logical location codes with no conversion, contact your next level of support.

If the location code begins with UTMPx, the expansion I/O unit's machine type, model and serial
number have not been set yet and this is a temporary unit identifier. To identify the unit, examine the
display panels on all of the expansion I/O units connected to the server until you find one with the same
characters in the first 5 digits of the top line in the unit's display. Record the unit's real machine type and
model from the unit label. Match the unit's machine type and model in the Unit type and locations table,
and follow the link to determine the service information.

Note: If locations for units are not in the preceding format, either they are not supported or there is a
problem in the firmware. Contact your next level of support.

Physical location codes

Physical location codes provide a mapping of logical functions and components (such as backplanes,
removable modules, connectors, ports, cables, and devices) to their specific locations within the physical
structure of the server.

Logical location codes

If the physical location cannot be mapped to a physical location code, the server's firmware generates a
logical location code. A logical location code is a sequence of location labels that identifies the path that
the system uses to communicate with a given resource.

Note: A resource has as many logical location codes as it has logical connections to the system. For
example, an external tape device connected to two I/O adapters will have two logical location codes.

An example of a logical location code is:

U7879.001.10ABCDE-P3-C31-T2-L23

The first part of the location code (through the T2 label) represents the physical location code for the
resource that communicates with the target resource. The remainder of the logical location code (L23)
represents exactly which resource is indicated.

Location code format

The location code is an alphanumeric string of variable length, consisting of a series of location
identifiers, separated by a dash. An example of a physical location for a fan is Un-A1.

The first position, represented by Un (where n is equal to any string contained between the U and the
hyphen) in the preceding example, is displayed in one of the forms in the following table.

Note: In location codes, the U is a constant digit; however, the numbered positions following the U are
variables and are dependent on your server. Each column defines the numbers that follow the U in the
beginning of the location code.

Finding parts, locations, and addresses 109

Machine type and model number in its location codes Feature codes and sequence numbers in its location
code

Utttt.mmm.sssssss-A1 Uffff.ccc.sssssss-A1
The leftmost code is always U. The leftmost code is always U.
tttt represents the unit type of the enclosure (drawer or ffff represents the feature code of the enclosure (drawer
node). or node).
mmm represents the model of the enclosure. ccc represents the sequence number of the enclosure .
sssssss represents the serial number for the enclosure. sssssss represents the serial number of the enclosure.
Note: The mmm or ccc number might not be displayed on all location codes for all servers. If the mmm value is not
displayed, the location code is displayed in one of the following forms:
v Utttt.sssssss-A1
v Uffff.sssssss-A1

The location code is hierarchical; that is, each location identifier in the string represents a physical part.
The order (from left to right), in which each identifier is shown, allows you to determine which parts
contain other parts in the string.

The dash (-) separator character represents a relationship between two components in the unit. In the
example of the fan, whose location code is Un-A1, the dash shows that the fan (A1) is contained in the
base unit (or Un). Modules, adapters, cables, and devices are all parts that are plugged into another part.
Their location codes will always show that they are plugged into another part as components of the
server. Another example follows:, Un-P1-C9 is a memory DIMM, with memory DIMM (C9) plugged into
a backplane (P1), which is inside the unit (Un).

For more information about the various location code label prefixes, refer to Location code labels.

Note: For devices, certain error conditions might cause an IBM i device to display the device location in
an AIX format.
Table 46. Unit type and locations
Unit type (Utttt.mmm) Link to location information
U5803.001 Locations
U5873.001 Locations

Location code labels

The following table identifies the location code label prefixes.

Note: These labels apply to system units only.

Table 47. Location code label prefixes for system units
Prefix Description Example
A Air-moving device Fan, blower
C Card connector IOP, IOA, DIMM, processor card
D Device Diskette, control panel
E Electrical Battery, power supply, ac charger
L Logical path SAS target IDE address, fibre channel LUN
N Horizontal placement for an empty rack location

110 Finding parts, locations, and addresses

Table 47. Location code label prefixes for system units (continued)
Prefix Description Example
P Planar System backplane
T Port
U Unit
V Virtual planar
W Worldwide unique ID
X EIA value for an empty rack location
Y Firmware FRU

Worldwide unique identifier

A worldwide unique identifier location label consists of the prefix W followed by a maximum of 16
uppercase hexadecimal digits with no leading zeros. A location code might not consist of a worldwide
unique identifier. When present, the worldwide unique identifier location label follows the location label
of the resource that interfaces with the resource that has the worldwide unique identifier, usually a port.

Locations
Use this information to help you map a location code to a position on the unit.

Note: The known logical location codes for this unit are listed next to the corresponding physical location
in the following information. If you are working with a logical location code for this unit and it is not
listed in the following information, contact your next level of support.

The following diagrams show the field replaceable unit (FRU) layout in the system. Use these diagrams
with the following tables.

Figure 53. Front view

Finding parts, locations, and addresses 111

Figure 54. Rear view

The following table provides location codes for parts that make up the server.
Table 48. Bulk power assembly (BPA) locations, and failing components
Failing item name Symbolic FRU name CCIN
DCA Un-E1 2C44
DCA UPIC connector Un-E1-T1
DCA UPIC connector Un-E1-T2
DCA Un-E2 2C44
DCA UPIC connector Un-E2-T1
DCA UPIC connector Un-E2-T2
Fans
Fan Un-E1-A1
Fan Un-E1-A2
Fan Un-E1-A3
Fan Un-E2-A1
Fan Un-E2-A2
Fan Un-E2-A3
Backplane
v Un-P1-C1
v Un-P2-C1
Planar Un-Px 50A2
IOA slot Un-Px-C1
IOA slot Un-Px-C2
IOA slot Un-Px-C3
IOA slot Un-Px-C4
IOA slot Un-Px-C5
IOA slot Un-Px-C6
IOA slot Un-Px-C7
IOA slot Un-Px-C8
IOA slot Un-Px-C9

112 Finding parts, locations, and addresses

Table 48. Bulk power assembly (BPA) locations, and failing components (continued)
Failing item name Symbolic FRU name CCIN
IOA slot Un-Px-C10
IB Riser Port Un-Px-T1
IB Riser Port Un-Px-T2
DASD
DASD backplane Un-P3 50A7
PORT card 1 Un-P3-C1 50A4
PORT card 2 Un-P3-C2 50A4
PORT card 3 Un-P3-C3 50A4
PORT card 4 Un-P3-C4 50A4
DASD drive bay Un-P3-D1
DASD drive bay Un-P3-D2
DASD drive bay Un-P3-D3
DASD drive bay Un-P3-D4
DASD drive bay Un-P3-D5
DASD drive bay Un-P3-D6
DASD drive bay Un-P3-D7
DASD drive bay Un-P3-D8
DASD drive bay Un-P3-D9
DASD drive bay Un-P3-D10
DASD drive bay Un-P3-D11
DASD drive bay Un-P3-D12
DASD drive bay Un-P3-D13
DASD drive bay Un-P3-D14
DASD drive bay Un-P3-D15
DASD drive bay Un-P3-D16
DASD drive bay Un-P3-D17
DASD drive bay Un-P3-D18
DASD drive bay Un-P3-D19
DASD drive bay Un-P3-D20
DASD drive bay Un-P3-D21
DASD drive bay Un-P3-D22
DASD drive bay Un-P3-D23
DASD drive bay Un-P3-D24
DASD drive bay Un-P3-D25
DASD drive bay Un-P3-D26
SAS conduit
SAS conduit Un-P4 50A5
SAS connector Un-P4-T1
SAS connector Un-P4-T2
SAS connector Un-P4-T3

Finding parts, locations, and addresses 113

Table 48. Bulk power assembly (BPA) locations, and failing components (continued)
Failing item name Symbolic FRU name CCIN
SAS connector Un-P4-T4
Media bay connector Un-P4-T5
Media bay connector Un-P4-T6
Midplane
Midplane Un-P5 50A8

5886
The information provided in this topic defines specific sections of a location code string. Use this
information to understand the meaning of a location code.

Using location codes

For additional information about reading your location code, use the following table to link to a specific
topic.

Location code topics that might be of interest Description

Location code overview Contains background information on the use of location
codes.
Physical location codes on page 115 Provides a definition for physical location code.
Logical location codes on page 115 Provides a definition for a logical location code.
Location code format on page 115 Provides descriptive information of the Un value in the
location code string. For example U5886.001.
Location code labels on page 116 Provides a table that identifies and defines the location
code labels. The location code labels begin with an
alphabetic character and follow the system serial number.
For example, U7879.001.10ABCDE-P3-C31-T2-L23. (The
system serial number is the 10ABCDE in the previous
example.) The P3, C31, T2, and L23 all contain an
alphabetic character that is identified in the Location
code labels table.
Worldwide unique identifier on page 117 Provides a definition for the worldwide unique identifier.
This group of digits follows the resource code labels and
always begins with the letter W.

Location code overview

Servers (system unit and expansion units) use physical location codes to provide mapping of replaceable
units. Location codes are produced by the server's firmware, which structures them so that they can be
used to identify specific parts in a system. The location code format is the same for all servers.

If you are working with a specific location code, the feature immediately follows the first character
(U5886). Refer to the Unit type and locations table.

If the location code ends with -Txx-Lxx, the server's firmware could not identify the physical location.
When a physical location cannot be identified, a logical location code is provided. Where logical location
codes occur in enclosures, the locations topic for the enclosure has the known conversions listed. For
logical location codes with no conversion, contact your next level of support.

114 Finding parts, locations, and addresses

If the location code begins with UTMPx, the expansion I/O unit's machine type, model and serial
number have not been set yet and this is a temporary unit identifier. To identify the unit, examine the
display panels on all of the expansion I/O units connected to the server until you find one with the same
characters in the first 5 digits of the top line in the unit's display. Record the unit's real machine type and
model from the unit label. Match the unit's machine type and model in the Unit type and locations table,
and follow the link to determine the service information.

Note: If locations for units are not in the preceding format, either they are not supported or there is a
problem in the firmware. Contact your next level of support.

Physical location codes

Physical location codes provide a mapping of logical functions and components (such as backplanes,
removable modules, connectors, ports, cables, and devices) to their specific locations within the physical
structure of the server.

Logical location codes

If the physical location cannot be mapped to a physical location code, the server's firmware generates a
logical location code. A logical location code is a sequence of location labels that identifies the path that
the system uses to communicate with a given resource.

Note: A resource has as many logical location codes as it has logical connections to the system. For
example, an external tape device connected to two I/O adapters will have two logical location codes.

An example of a logical location code is:

U7879.001.10ABCDE-P3-C31-T2-L23

The first part of the location code (through the T2 label) represents the physical location code for the
resource that communicates with the target resource. The remainder of the logical location code (L23)
represents exactly which resource is indicated.

Location code format

The location code is an alphanumeric string of variable length, consisting of a series of location
identifiers, separated by a dash. An example of a physical location for a fan is Un-A1.

The first position, represented by Un (where n is equal to any string contained between the U and the
hyphen) in the preceding example, is displayed in one of the forms in the following table.

Note: In location codes, the U is a constant digit; however, the numbered positions following the U are
variables and are dependent on your server. Each column defines the numbers that follow the U in the
beginning of the location code.

Machine type and model number in its location codes Feature codes and sequence numbers in its location
code

Utttt.mmm.sssssss-A1 Uffff.ccc.sssssss-A1
The leftmost code is always U. The leftmost code is always U.
tttt represents the unit type of the enclosure (drawer or ffff represents the feature code of the enclosure (drawer
node). or node).
mmm represents the model of the enclosure. ccc represents the sequence number of the enclosure .
sssssss represents the serial number for the enclosure. sssssss represents the serial number of the enclosure.

Finding parts, locations, and addresses 115

Machine type and model number in its location codes Feature codes and sequence numbers in its location
code

Utttt.mmm.sssssss-A1 Uffff.ccc.sssssss-A1
Note: The mmm or ccc number might not be displayed on all location codes for all servers. If the mmm value is not
displayed, the location code is displayed in one of the following forms:
v Utttt.sssssss-A1
v Uffff.sssssss-A1

The location code is hierarchical; that is, each location identifier in the string represents a physical part.
The order (from left to right), in which each identifier is shown, allows you to determine which parts
contain other parts in the string.

The dash (-) separator character represents a relationship between two components in the unit. In the
example of the fan, whose location code is Un-A1, the dash shows that the fan (A1) is contained in the
base unit (or Un). Modules, adapters, cables, and devices are all parts that are plugged into another part.
Their location codes always show that they are plugged into another part as components of the server.
Another example follows:, Un-P1-C9 is a memory DIMM, with memory DIMM (C9) plugged into a
backplane (P1), which is inside the unit (Un).

For more information about the various location code label prefixes, refer to Location code labels.

Note: For devices, certain error conditions might cause an IBM i device to display the device location in
an AIX format.
Table 49. Unit type and locations
Unit type (Utttt) Link to location information
U5886.001 Locations

Location code labels

The following table identifies the location code label prefixes.

Note: These labels apply to system units only.

Table 50. Location code label prefixes for system units
Prefix Description Example
A Air-moving device Fan, blower
C Card connector IOP, IOA, DIMM, processor card
D Device Diskette, control panel
E Electrical Battery, power supply, ac charger
L Logical path SAS target IDE address, fibre channel LUN
N Horizontal placement for an empty rack location
P Planar System backplane
T Port
U Unit
V Virtual planar
W Worldwide unique ID
X EIA value for an empty rack location

116 Finding parts, locations, and addresses

Table 50. Location code label prefixes for system units (continued)
Prefix Description Example
Y Firmware FRU

Worldwide unique identifier

A worldwide unique identifier location label consists of the prefix W followed by a maximum of 16
uppercase hexadecimal digits with no leading zeros. A location code might not consist of a worldwide
unique identifier. When present, the worldwide unique identifier location label follows the location label
of the resource that interfaces with the resource that has the worldwide unique identifier, usually a port.

Locations
Use this information to help you map a location code to a position on the unit.

Note: The known logical location codes for this unit are listed next to the corresponding physical location
in the following information. If you are working with a logical location code for this unit and it is not
listed in the following information, contact your next level of support.

The following diagrams show the field replaceable unit (FRU) layout in the system. Use these diagrams
with the following tables.

Figure 55. Front and rear views

The following table provides location codes for parts that make up the server.
Table 51. FRU locations and failing components
Failing item name Symbolic failing item Physical location code Identify LED
name
System unit Un

Finding parts, locations, and addresses 117

Table 51. FRU locations and failing components (continued)
Failing item name Symbolic failing item Physical location code Identify LED
name
ESM
ESM A Un-C1 Yes
ESM B Un-C2 Yes
Power supplies
Power supply PWRSPLY Un-E1 Yes
Power supply PWRSPLY Un-E2 Yes
Midplane
Midplane Un-P1 Yes
Device physical locations
Disk drive 1 Un-P1-D1 Yes
Disk drive 2 Un-P1-D2 Yes
Disk drive 3 Un-P1-D3 Yes
Disk drive 4 Un-P1-D4 Yes
Disk drive 5 Un-P1-D5 Yes
Disk drive 6 Un-P1-D6 Yes
Disk drive 7 Un-P1-D7 Yes
Disk drive 8 Un-P1-D8 Yes
Disk drive 9 Un-P1-D9 Yes
Disk drive 10 Un-P1-D10 Yes
Disk drive 11 Un-P1-D11 Yes
Disk drive 12 Un-P1-D12 Yes

Addresses
Use this information to locate system addresses.

Use the address to find the location and then go to locations to Part locations and location codes on
page 2 to find the physical location.

8203-E4A, 8261-E4S, 9407-M15, and 9408-M25 addresses

You can cross-reference a disk drive physical location code to the address.

Use the address to find the location for the system, then go to 8203-E4A, 8261-E4S, 9407-M15, 9408-M25
on page 2 to find additional location information.
Table 52. IOA, and device address information, running IBM i
Position Possible failing item DSA (BBBBCcbb) Unit address
Un-P1 Embedded SAS 02001000 (primary) 7FFFFFFF
controller
Un-P1-C1 PCI-E adapter 02040000 Not applicable
Un-P1-C2 PCI-E adapter 02050000 Not applicable
Un-P1-C3 PCI-E adapter 02070000 Not applicable

118 Finding parts, locations, and addresses

Table 52. IOA, and device address information, running IBM i (continued)
Position Possible failing item DSA (BBBBCcbb) Unit address
Un-P1-C4 PCI-X adapter 02021000 Not applicable
Un-P1-C5 PCI-X adapter 02031000 Not applicable
Un-P1-C9 PCI auxiliary cache 02060000 7FFFFFFF
card
Un-P1-C10 RAID card 02001000 7FFFFFFF
Un-P2-D1 Removable media 02001000 020000FF
Un-P2-D2 Removable media 02001000 030000FF
Un-P2-D3 Disk drive 1 02001000 040200FF
Un-P2-D4 Disk drive 2 02001000 040400FF
Un-P2-D5 Disk drive 3 02001000 040600FF
Un-P2-D6 Disk drive 4 02001000 040700FF
Un-P2-D7 Disk drive 5 02001000 040800FF
Un-P2-D8 Disk drive 6 02001000 040900FF
Un-P2-D9 (SFF Disk drive 7 02001000 040B00FF
only)
Un-P2-D10 (SFF Disk drive 8 02001000 040D00FF
only)

8204-E8A and 9409-M50 addresses

You can cross-reference a disk drive physical location code to the address.

Use the address to find the location for the system, then go to 8204-E8A and 9409-M50 on page 13 to
find additional location information.
Table 53. IOA, and device address information, running IBM i
Position Possible failing item DSA (BBBBCcbb) Unit address
Un-P1 Embedded SAS 02001000 7FFFFFFF
controller
Un-P1-C1 PCI-E adapter 02040000 Not applicable
Un-P1-C2 PCI-E adapter 02050000 Not applicable
Un-P1-C3 PCI-E adapter 02070000 Not applicable
Un-P1-C4 PCI-X adapter 02021000 Not applicable
Un-P1-C5 PCI-X adapter 02031000 Not applicable
Un-P1-C10 PCI auxiliary cache 02060000 7FFFFFFF
card
Un-P1-C11 RAID card 02001000 7FFFFFFF
Un-P2-D1 Removable media 02001000 020000FF
Un-P2-D2 Removable media 02001000 030000FF
Un-P2-D3 Disk drive 1 02001000 040200FF
Un-P2-D4 Disk drive 2 02001000 040400FF
Un-P2-D5 Disk drive 3 02001000 040600FF
Un-P2-D6 Disk drive 4 02001000 040700FF
Un-P2-D7 Disk drive 5 02001000 040800FF

Finding parts, locations, and addresses 119

Table 53. IOA, and device address information, running IBM i (continued)
Position Possible failing item DSA (BBBBCcbb) Unit address
Un-P2-D8 Disk drive 6 02001000 040900FF
Un-P2-D9 (SFF Disk drive 7 02001000 040B00FF
only)
Un-P2-D10 (SFF Disk drive 8 02001000 040D00FF
only)

8234-EMA, 9117-MMA, and 9406-MMA addresses

You can cross-reference a disk drive physical location code to the address.

Use the address to find the location for the system, then go to 8234-EMA, 9117-MMA, and 9406-MMA
on page 25 to find additional location information.
Table 54. IOA, and device address information for running IBM i
Position Possible failing item DSA (BBBBCcbb) Unit address
Un -P1 Embedded SAS 0200-20-00 (primary) Not applicable
controller
0220-20-00 (secondary 1)

0240-20-00 (secondary 2)

0260-20-00 (secondary 3)
Un -P1-C1 PCI adapter 0204-00-00 (primary) Not applicable

0224-00-00 (secondary 1)

0244-00-00 (secondary 2)

0264-00-00 (secondary 3)
Un -P1-C2 PCI adapter 0205-00-00 (primary) Not applicable

0225-00-00 (secondary 1)

0245-00-00 (secondary 2)

0265-00-00 (secondary 3)
Un -P1-C3 PCI adapter 0206-00-00 (primary) Not applicable

0226-00-00 (secondary 1)

0246-00-00 (secondary 2)

0266-00-00 (secondary 3)
Un -P1-C4 PCI adapter 0201-10-00 (primary) Not applicable

0221-10-00 (secondary 1)

0241-10-00 (secondary 2)

0261-10-00 (secondary 3)

120 Finding parts, locations, and addresses

Table 54. IOA, and device address information for running IBM i (continued)
Position Possible failing item DSA (BBBBCcbb) Unit address
Un -P1-C5 PCI adapter 0202-10-00 (primary) Not applicable

0222-10-00 (secondary 1)

0242-10-00 (secondary 2)

0262-10-00 (secondary 3)
Un -P1-C6 PCI adapter 0207-00-00 (primary) Not applicable

0227-00-00 (secondary 1)

0247-00-00 (secondary 2)

0267-00-00 (secondary 3)
Un -P3-D1 Disk drive 1 0200-20-00 (primary) 000200FF

0220-20-00 (secondary 1)

0240-20-00 (secondary 2)

0260-20-00 (secondary 3)
Un -P3-D2 Disk drive 2 0200-20-00 (primary) 000300FF

0220-20-00 (secondary 1)

0240-20-00 (secondary 2)

0260-20-00 (secondary 3)
Un -P3-D3 Disk drive 3 0200-20-00 (primary) 000400FF

0220-20-00 (secondary 1)

0240-20-00 (secondary 2)

0260-20-00 (secondary 3)
Un -P3-D4 Disk drive 4 0200-20-00 (primary) 000500FF

0220-20-00 (secondary 1)

0240-20-00 (secondary 2)

0260-20-00 (secondary 3)
Un -P3-D5 Disk drive 5 0200-20-00 (primary) 000600FF

0220-20-00 (secondary 1)

0240-20-00 (secondary 2)

0260-20-00 (secondary 3)
Un -P3-D6 Disk drive 6 0200-20-00 (primary) 000700FF

0220-20-00 (secondary 1)

0240-20-00 (secondary 2)

0260-20-00 (secondary 3)

Finding parts, locations, and addresses 121

Table 54. IOA, and device address information for running IBM i (continued)
Position Possible failing item DSA (BBBBCcbb) Unit address
Un -P4-D1 IDE drive 1 0200-20-00 (primary) 040000FF

0220-20-00 (secondary 1)

0240-20-00 (secondary 2)

0260-20-00 (secondary 3)

0595, 5095, and 7311-D20 addresses

You can cross-reference a disk drive physical location code to the address.

Use the address to find the location for the system, then go to 0595, 5095, and 7311-D20 on page 61 to
find additional location information.
Table 55. IOP, IOA, and device address information
Position Possible failing item DSA (BBBBCcbb) Unit address
IOA and device DSAs do
not conform to the
following rules if the IOA is
manually reassigned after
IPL.
C01 (IXS capable position) IOP xxxx-20-00 FFFFFFFF
C02 (empty if IXS in C01) Storage IOA xxxx-20-00 2FFFFFFF
C02 (empty if IXS in C01) Communication or xxxx-20-00 E2FFFFFF
workstation IOA
C03 IOP xxxx-24-00 FFFFFFFF
C03 Storage IOA xxxx-20-00 4FFFFFFF
C03 Communication or xxxx-20-00 E4FFFFFF
workstation IOA
C03 IXS attached IOA xxxx-20-00 E004FFFF
C04 Storage IOA The IOA has the same DSA 6FFFFFFF
as the first IOP found in
the following list: C03, C01.
C04 Communication or The IOA has the same DSA E6FFFFFF
workstation IOA as the first IOP found in
the following list: C03, C01.
C04 IXS attached IOA The IOA has the same DSA E006FFFF
as the first IOP found in
the following list: C03, C01.
C06 IOP yyyy-20-00 FFFFFFFF
C07 Storage IOA yyyy-20-00 2FFFFFFF
C07 Communication or yyyy-20-00 E2FFFFFF
workstation IOA
C08 Storage IOA yyyy-20-00 6FFFFFFF
C08 Communication or yyyy-20-00 E6FFFFFF
workstation IOA
C08 IXS attached IOA yyyy-20-00 E006FFFF

122 Finding parts, locations, and addresses

Table 55. IOP, IOA, and device address information (continued)
Position Possible failing item DSA (BBBBCcbb) Unit address
D01, D07 Disk unit The disk unit has the same xy0100FF (where x is the
DSA as the IOP controlling same as the first character
the storage IOA. of the xFFFFFFF IOA Unit
Address and y is I/O bus
0, 1, 2, or 3. Storage IOA
buses begin with 0 and are
numbered from the
tailstock toward the middle
of the card. Find the
storage IOA with the same
DSA and xFFFFFFF
address, then trace the I/O
bus cable to determine if
the position is D01 or D07.)
D02, D08 Disk unit xy0200FF (where x is the
same as the first character
of the xFFFFFFF IOA Unit
Address and y is I/O bus
0, 1, 2, or 3. Storage IOA
buses begin with 0 and are
numbered from the
tailstock toward the middle
of the card. Find the
storage IOA with the same
DSA and xFFFFFFF
address, then trace the I/O
bus cable to determine if
the position is D02 or D08.)
D03, D09 Disk unit xy0300FF (where x is the
same as the first character
of the xFFFFFFF IOA Unit
Address and y is I/O bus
0, 1, 2, or 3. Storage IOA
buses begin with 0 and are
numbered from the
tailstock toward the middle
of the card. Find the
storage IOA with the same
DSA and xFFFFFFF
address, then trace the I/O
bus cable to determine if
the position is D03 or D09.)
D04, D10 Disk unit xy0400FF (where x is the
same as the first character
of the xFFFFFFF IOA Unit
Address and y is I/O bus
0, 1, 2, or 3. Storage IOA
buses begin with 0 and are
numbered from the
tailstock toward the middle
of the card. Find the
storage IOA with the same
DSA and xFFFFFFF
address, then trace the I/O
bus cable to determine if
the position is D04 or D10.)

Finding parts, locations, and addresses 123

Table 55. IOP, IOA, and device address information (continued)
Position Possible failing item DSA (BBBBCcbb) Unit address
D05, D11 Disk unit xy0E00FF (where x is the
same as the first character
of the xFFFFFFF IOA Unit
Address and y is I/O bus
0, 1, 2, or 3. Storage IOA
buses begin with 0 and are
numbered from the
tailstock toward the middle
of the card. Find the
storage IOA with the same
DSA and xFFFFFFF
address, then trace the I/O
bus cable to determine if
the position is D05 or D11.)
D06, D12 Disk unit xy0F00FF (where x is the
same as the first character
of the xFFFFFFF IOA Unit
Address and y is I/O bus
0, 1, 2, or 3. Storage IOA
buses begin with 0 and are
numbered from the
tailstock toward the middle
of the card. Find the
storage IOA with the same
DSA and xFFFFFFF
address, then trace the I/O
bus cable to determine if
the position is D06 or D12.)

5094, 5294, 5096, and 5296 addresses

You can cross-reference a disk drive physical location code to the address.

Use the address to find the location for the system, then go to 5094, 5294, 5096, and 5296 on page 67 to
find additional location information.

Remember: References to disk units, media (optical and tape), and device boards in either the following
table does not apply to the 5096, or 5296.
Table 56. IOP, IOA, and device address information
Position Possible failing item DSA (BBBBCcbb) Unit address
IOA and device DSAs do not conform to the
following rules if the IOA is manually
reassigned after IPL.
C01 (IXS capable IOP xxxx-20-00 FFFFFFFF
position)
C02 (empty if IXS Storage IOA xxxx-20-00 2FFFFFFF
in C01)
C02 (empty if IXS Communications or xxxx-20-00 E2FFFFFF
in C01) Workstation IOA
C03 IOP xxxx-24-00 FFFFFFFF
C03 Storage IOA xxxx-20-00 4FFFFFFF

124 Finding parts, locations, and addresses

Table 56. IOP, IOA, and device address information (continued)
Position Possible failing item DSA (BBBBCcbb) Unit address
C03 Communications or xxxx-20-00 E4FFFFFF
Workstation IOA
C03 IXS attached IOA xxxx-20-00 E004FFFF
C04 Storage IOA The IOA has the same DSA as the first IOP 6FFFFFFF
found in the following list: C03, C01.
C04 Communications or The IOA has the same DSA as the first IOP E6FFFFFF
Workstation IOA found in the following list: C03, C01.
C04 IXS attached IOA The IOA has the same DSA as the first IOP E006FFFF
found in the following list: C03, C01.
C05 (IXS capable IOP yyyy-20-00 FFFFFFFF
position)
C06 (empty if IXS Storage IOA yyyy-20-00 2FFFFFFF
in C05)
C06 (empty if IXS Communications or yyyy-20-00 E2FFFFFF
in C05) Workstation IOA
C07 IOP yyyy-23-00 FFFFFFFF
C07 Storage IOA yyyy-20-00 3FFFFFFF
C07 Communications or yyyy-20-00 E3FFFFFF
Workstation IOA
C07 IXS attached IOA yyyy-20-00 E003FFFF
C08 IOP yyyy-24-00 FFFFFFFF
C08 Storage IOA The IOA has the same DSA as the first IOP 4FFFFFFF
found in the following list: C07, C05.
C08 Communications or The IOA has the same DSA as the first IOP E4FFFFFF
Workstation IOA found in the following list: C07, C05.
C08 IXS attached IOA The IOA has the same DSA as the first IOP E004FFFF
found in the following list: C07, C05.
C09 Storage IOA The IOA has the same DSA as the first IOP 6FFFFFFF
found in the following list: C08, C07, C05.
C09 Communications or The IOA has the same DSA as the first IOP E6FFFFFF
Workstation IOA found in the following list: C08, C07, C05.
C09 IXS attached IOA The IOA has the same DSA as the first IOP E006FFFF
found in the following list: C08, C07, C05.
C11 (IXS capable IOP zzzz-20-00 FFFFFFFF
position)
C12 (empty if IXS Storage IOA zzzz-20-00 2FFFFFFF
in C11)
C12 (empty if IXS Communications or zzzz-20-00 E2FFFFFF
in C11) Workstation IOA
C13 IOP zzzz-23-00 FFFFFFFF
C13 Storage IOA zzzz-20-00 3FFFFFFF
C13 Communications or zzzz-20-00 E3FFFFFF
Workstation IOA
C13 IXS attached IOA zzzz-20-00 E003FFFF
C14 IOP zzzz-24-00 FFFFFFFF

Finding parts, locations, and addresses 125

Table 56. IOP, IOA, and device address information (continued)
Position Possible failing item DSA (BBBBCcbb) Unit address
C14 Storage IOA The IOA has the same DSA as the first IOP 4FFFFFFF
found in the following list: C13, C11.
C14 Communications or The IOA has the same DSA as the first IOP E4FFFFFF
Workstation IOA found in the following list: C13, C11.
C14 IXS attached IOA The IOA has the same DSA as the first IOP E004FFFF
found in the following list: C13, C11.
C15 Storage IOA The IOA has the same DSA as the first IOP 6FFFFFFF
found in the following list: C14, C13, C11.
C15 Communications or The IOA has the same DSA as the first IOP E6FFFFFF
Workstation IOA found in the following list: C14, C13, C11.
C15 IXS attached IOA The IOA has the same DSA as the first IOP E006FFFF
found in the following list: C14, C13, C11.
D01 Disk unit The disk unit has the same DSA as the IOA x00300FF (where x is the
attached to the internal cable labeled "L-1". same as the first
character of the
xFFFFFFF IOA Unit
Address)
D02 Disk unit The disk unit has the same DSA as the IOA x00400FF (where x is the
attached to the internal cable labeled "L-1". same as the first
character of the
xFFFFFFF IOA Unit
Address)
D03 Disk unit The disk unit has the same DSA as the IOA x00500FF (where x is the
attached to the internal cable labeled "L-1". same as the first
character of the
xFFFFFFF IOA Unit
Address)
D04 Disk unit The disk unit has the same DSA as the IOA x00600FF (where x is the
attached to the internal cable labeled "L-1". same as the first
character of the
xFFFFFFF IOA Unit
Address)
D05 Disk unit The disk unit has the same DSA as the IOA x00700FF (where x is the
attached to the internal cable labeled "L-1". same as the first
character of the
xFFFFFFF IOA Unit
Address)
D06 Disk unit The disk unit has the same DSA as the IOA x00300FF (where x is the
attached to the internal cable labeled "R-2". same as the first
character of the
xFFFFFFF IOA Unit
Address)
D07 Disk unit The disk unit has the same DSA as the IOA x00400FF (where x is the
attached to the internal cable labeled "R-2". same as the first
character of the
xFFFFFFF IOA Unit
Address)
D08 Disk unit The disk unit has the same DSA as the IOA x00500FF (where x is the
attached to the internal cable labeled "R-2". same as the first
character of the
xFFFFFFF IOA Unit
Address)

126 Finding parts, locations, and addresses

Table 56. IOP, IOA, and device address information (continued)
Position Possible failing item DSA (BBBBCcbb) Unit address
D09 Disk unit The disk unit has the same DSA as the IOA x00600FF (where x is the
attached to the internal cable labeled "R-2". same as the first
character of the
xFFFFFFF IOA Unit
Address)
D10 Disk unit The disk unit has the same DSA as the IOA x00700FF (where x is the
attached to the internal cable labeled "R-2". same as the first
character of the
xFFFFFFF IOA Unit
Address)
D11 Disk unit The disk unit has the same DSA as the IOA x10300FF (where x is the
attached to the internal cable labeled "L-1". same as the first
character of the
xFFFFFFF IOA Unit
Address)
D12 Disk unit The disk unit has the same DSA as the IOA x10400FF (where x is the
attached to the internal cable labeled "L-1". same as the first
character of the
xFFFFFFF IOA Unit
Address)
D13 Disk unit The disk unit has the same DSA as the IOA x10500FF (where x is the
attached to the internal cable labeled "L-1". same as the first
character of the
xFFFFFFF IOA Unit
Address)
D14 Disk unit The disk unit has the same DSA as the IOA x10600FF (where x is the
attached to the internal cable labeled "L-1". same as the first
character of the
xFFFFFFF IOA Unit
Address)
D15 Disk unit The disk unit has the same DSA as the IOA x10700FF (where x is the
attached to the internal cable labeled "L-1". same as the first
character of the
xFFFFFFF IOA Unit
Address)
D16 Disk unit The disk unit has the same DSA as the IOA x10300FF (where x is the
attached to the internal cable labeled "R-2". same as the first
character of the
xFFFFFFF IOA Unit
Address)
D17 Disk unit The disk unit has the same DSA as the IOA x10400FF (where x is the
attached to the internal cable labeled "R-2". same as the first
character of the
xFFFFFFF IOA Unit
Address)
D18 Disk unit The disk unit has the same DSA as the IOA x10500FF (where x is the
attached to the internal cable labeled "R-2". same as the first
character of the
xFFFFFFF IOA Unit
Address)

Finding parts, locations, and addresses 127

Table 56. IOP, IOA, and device address information (continued)
Position Possible failing item DSA (BBBBCcbb) Unit address
D19 Disk unit The disk unit has the same DSA as the IOA x10600FF (where x is the
attached to the internal cable labeled "R-2". same as the first
character of the
xFFFFFFF IOA Unit
Address)
D20 Disk unit The disk unit has the same DSA as the IOA x10700FF (where x is the
attached to the internal cable labeled "R-2". same as the first
character of the
xFFFFFFF IOA Unit
Address)
D21 Disk unit The disk unit has the same DSA as the IOA x20300FF (where x is the
attached to the internal cable labeled "L-1". same as the first
character of the
xFFFFFFF IOA Unit
Address)
D22 Disk unit The disk unit has the same DSA as the IOA x20400FF (where x is the
attached to the internal cable labeled "L-1". same as the first
character of the
xFFFFFFF IOA Unit
Address)
D23 Disk unit The disk unit has the same DSA as the IOA x20500FF (where x is the
attached to the internal cable labeled "L-1". same as the first
character of the
xFFFFFFF IOA Unit
Address)
D24 Disk unit The disk unit has the same DSA as the IOA x20600FF (where x is the
attached to the internal cable labeled "L-1". same as the first
character of the
xFFFFFFF IOA Unit
Address)
D25 Disk unit The disk unit has the same DSA as the IOA x20700FF (where x is the
attached to the internal cable labeled "L-1". same as the first
character of the
xFFFFFFF IOA Unit
Address)
D26 Disk unit The disk unit has the same DSA as the IOA x20300FF (where x is the
attached to the internal cable labeled "R-2". same as the first
character of the
xFFFFFFF IOA Unit
Address)
D27 Disk unit The disk unit has the same DSA as the IOA x20400FF (where x is the
attached to the internal cable labeled "R-2". same as the first
character of the
xFFFFFFF IOA Unit
Address)
D28 Disk unit The disk unit has the same DSA as the IOA x20500FF (where x is the
attached to the internal cable labeled "R-2". same as the first
character of the
xFFFFFFF IOA Unit
Address)

128 Finding parts, locations, and addresses

Table 56. IOP, IOA, and device address information (continued)
Position Possible failing item DSA (BBBBCcbb) Unit address
D29 Disk unit The disk unit has the same DSA as the IOA x20600FF (where x is the
attached to the internal cable labeled "R-2". same as the first
character of the
xFFFFFFF IOA Unit
Address)
D30 Disk unit The disk unit has the same DSA as the IOA x20700FF (where x is the
attached to the internal cable labeled "R-2". same as the first
character of the
xFFFFFFF IOA Unit
Address)
D31 Disk unit The disk unit has the same DSA as the IOA x00100FF (where x is the
attached to the internal flat ribbon cable. same as the first
character of the
xFFFFFFF IOA Unit
Address)
D32 Disk unit The disk unit has the same DSA as the IOA x00200FF (where x is the
attached to the internal flat ribbon cable. same as the first
character of the
xFFFFFFF IOA Unit
Address)
D33 Disk unit The disk unit has the same DSA as the IOA x00300FF (where x is the
attached to the internal flat ribbon cable. same as the first
character of the
xFFFFFFF IOA Unit
Address)
D34 Disk unit The disk unit has the same DSA as the IOA x00400FF (where x is the
attached to the internal flat ribbon cable. same as the first
character of the
xFFFFFFF IOA Unit
Address)
D35 Disk unit The disk unit has the same DSA as the IOA x00500FF (where x is the
attached to the internal flat ribbon cable. same as the first
character of the
xFFFFFFF IOA Unit
Address)
D36 Disk unit The disk unit has the same DSA as the IOA x10300FF (where x is the
attached to the internal flat ribbon cable. same as the first
character of the
xFFFFFFF IOA Unit
Address)
D37 Disk unit The disk unit has the same DSA as the IOA x10400FF (where x is the
attached to the internal flat ribbon cable. same as the first
character of the
xFFFFFFF IOA Unit
Address)
D38 Disk unit The disk unit has the same DSA as the IOA x10500FF (where x is the
attached to the internal flat ribbon cable. same as the first
character of the
xFFFFFFF IOA Unit
Address)

Finding parts, locations, and addresses 129

Table 56. IOP, IOA, and device address information (continued)
Position Possible failing item DSA (BBBBCcbb) Unit address
D39 Disk unit The disk unit has the same DSA as the IOA x10600FF (where x is the
attached to the internal flat ribbon cable. same as the first
character of the
xFFFFFFF IOA Unit
Address)
D40 Disk unit The disk unit has the same DSA as the IOA x10700FF (where x is the
attached to the internal flat ribbon cable. same as the first
character of the
xFFFFFFF IOA Unit
Address)
D41 Optical The disk unit has the same DSA as the IOA x00600FF (where x is the
attached to the internal flat ribbon cable. same as the first
character of the
xFFFFFFF IOA Unit
Address)
D42 Tape The disk unit has the same DSA as the IOA x00700FF (where x is the
attached to the internal flat ribbon cable. same as the first
character of the
xFFFFFFF IOA Unit
Address)
D46 Disk unit The disk unit has the same DSA as the IOA x20300FF (where x is the
attached to the internal flat ribbon cable. same as the first
character of the
xFFFFFFF IOA Unit
Address)
D47 Disk unit The disk unit has the same DSA as the IOA x20400FF (where x is the
attached to the internal flat ribbon cable. same as the first
character of the
xFFFFFFF IOA Unit
Address)
D48 Disk unit The disk unit has the same DSA as the IOA x20500FF (where x is the
attached to the internal flat ribbon cable. same as the first
character of the
xFFFFFFF IOA Unit
Address)
D49 Disk unit The disk unit has the same DSA as the IOA x20600FF (where x is the
attached to the internal flat ribbon cable. same as the first
character of the
xFFFFFFF IOA Unit
Address)
D50 Disk unit The disk unit has the same DSA as the IOA x20700FF (where x is the
attached to the internal flat ribbon cable. same as the first
character of the
xFFFFFFF IOA Unit
Address)

5786, 5787, 7031-D24, and 7031-T24 addresses

Use the table to cross reference a disk drive physical location code to that of the SCSI cable address.

Use the address to find the location for the system, then go to 5786, 5787, 7031-D24, and 7031-T24 on
page 75 to find additional location information.

130 Finding parts, locations, and addresses

Note: The x in the following table represents the I/O adapter number of the attached I/O card and the y
represents the SCSI bus number.
Table 57. Device cable address information
Unit address (SCSI cable from I/O adapter Unit address (SCSI cable from SCSI
Physical location code to SCSI interface card) interface card to SCSI interface card)
Un-P1-D1 xy0200FF xy0A00FF
Un-P1-D2 xy0300FF xy0B00FF
Un-P1-D3 xy0400FF xy0C00FF
Un-P1-D4 xy0500FF xy0D00FF
Un-P1-D5 xy0600FF xy0E00FF
Un-P1-D6 xy0700FF xy0F00FF
Un-P1-D7 xy0200FF xy0A00FF
Un-P1-D8 xy0300FF xy0B00FF
Un-P1-D9 xy0400FF xy0C00FF
Un-P1-D10 xy0500FF xy0D00FF
Un-P1-D11 xy0600FF xy0E00FF
Un-P1-D12 xy0700FF xy0F00FF
Un-P2-D1 xy0200FF xy0A00FF
Un-P2-D2 xy0300FF xy0B00FF
Un-P2-D3 xy0400FF xy0C00FF
Un-P2-D4 xy0500FF xy0D00FF
Un-P2-D5 xy0600FF xy0E00FF
Un-P2-D6 xy0700FF xy0F00FF
Un-P2-D7 xy0200FF xy0A00FF
Un-P2-D8 xy0300FF xy0B00FF
Un-P2-D9 xy0400FF xy0C00FF
Un-P2-D10 xy0500FF xy0D00FF
Un-P2-D11 xy0600FF xy0E00FF
Un-P2-D12 xy0700FF xy0F00FF

5790 and 7311-D11 addresses

You can cross-reference a disk drive physical location code to the address.

Use the address to find the location for the system, then go to 5790 and 7311-D11 on page 82 to find
additional location information.
Table 58. IOP, IOA, and device address information
Position Possible failing item DSA (BBBBCcbb) Unit address
Un-P1-C1 IOP or IOA xxxx-20-00
Un-P1-C2 IOP or IOA xxxx-22-00
If the IOA is controlled by
a physical IOP, then it has
the DSA of the controlling
IOP instead)

Finding parts, locations, and addresses 131

Table 58. IOP, IOA, and device address information (continued)
Position Possible failing item DSA (BBBBCcbb) Unit address
Un-P1-C3 IOP or IOA xxxx-26-00 s
If the IOA is controlled by
a physical IOP, then it has
the DSA of the controlling
IOP instead)
Un-P1-C4 IOP or IOA yyyy-20-00
Un-P1-C5 IOP or IOA yyyy-22-00
If the IOA is controlled by
a physical IOP, then it has
the DSA of the controlling
IOP instead)
Un-P1-C6 IOP or IOA yyyy-26-00
If the IOA is controlled by
a physical IOP, then it has
the DSA of the controlling
IOP instead)

5796 and 7314-G30 addresses

You can cross-reference a disk drive physical location code to the address.

Use the address to find the location for the system, then go to 5796 and 7314-G30 on page 97 to find
additional location information.
Table 59. IOP, IOA, and device address information
Position Possible failing item DSA (BBBBCcbb) Unit address
Un-P1-C1 PCI adapter aaaa-00-00 N/A
Un-P1-C2 PCI adapter bbbb-00-00 N/A
Un-P1-C3 PCI adapter cccc-00-00 N/A
Un-P1-C4 PCI adapter dddd-00-00 N/A
Un-P1-C5 PCI adapter eeee-00-00 N/A
Un-P1-C6 PCI adapter ffff-00-00 N/A

5802 and 5877 addresses

You can cross-reference a disk drive physical location code to the address.

Use the address to find the location for the system, then go to 5802 and 5877 on page 102 to find
additional location information.
Table 60. IOA, and device address information, running IBM i
Position Possible failing item DSA (BBBBCcbb) Unit address
Ux-P1-C1 PCIe adapter aaaa-00-00 Not applicable
Ux-P1-C2 PCIe adapter bbbb-00-00 Not applicable
Ux-P1-C3 PCIe adapter cccc-00-00 Not applicable
Ux-P1-C4 PCIe adapter dddd-00-00 Not applicable
Ux-P1-C5 PCIe adapter eeee-00-00 Not applicable
Ux-P1-C6 PCIe adapter ffff-00-00 Not applicable

132 Finding parts, locations, and addresses

Table 60. IOA, and device address information, running IBM i (continued)
Position Possible failing item DSA (BBBBCcbb) Unit address
Ux-P1-C7 PCIe adapter gggg-00-00 Not applicable
Ux-P1-C8 PCIe adapter hhhh-00-00 Not applicable
Ux-P1-C9 PCIe adapter iiii-00-00 Not applicable
Ux-P1-C10 PCIe adapter jjjj-00-00 Not applicable
Ux-P3-D1 DASD drive 1 (5802 The disk unit has the same DSA as the 000600FF or 040600FF
only) storage IOA controlling it.
Ux-P3-D2 DASD drive 2 (5802 The disk unit has the same DSA as the 000700FF or 040700FF
only) storage IOA controlling it.
Ux-P3-D3 DASD drive 3 (5802 The disk unit has the same DSA as the 000800FF or 040800FF
only) storage IOA controlling it.
Ux-P3-D4 DASD drive 4 (5802 The disk unit has the same DSA as the 000900FF or 040900FF
only) storage IOA controlling it.
Ux-P3-D5 DASD drive 5 (5802 The disk unit has the same DSA as the 000A00FF or 040A00FF
only) storage IOA controlling it.
Ux-P3-D6 DASD drive 6 (5802 The disk unit has the same DSA as the 000B00FF or 040B00FF
only) storage IOA controlling it.
Ux-P3-D7 DASD drive 7 (5802 The disk unit has the same DSA as the 000C00FF or 040C00FF
only) storage IOA controlling it.
Ux-P3-D8 DASD drive 8 (5802 The disk unit has the same DSA as the 000D00FF or 040D00FF
only) storage IOA controlling it.
Ux-P3-D9 DASD drive 9 (5802 The disk unit has the same DSA as the 000E00FF or 040E00FF
only) storage IOA controlling it.
Ux-P3-D10 DASD drive 10 (5802 The disk unit has the same DSA as the 000600FF or 040600FF
only) storage IOA controlling it.
Ux-P3-D11 DASD drive 11 (5802 The disk unit has the same DSA as the 000700FF or 040700FF
only) storage IOA controlling it.
Ux-P3-D12 DASD drive 12 (5802 The disk unit has the same DSA as the 000800FF or 040800FF
only) storage IOA controlling it.
Ux-P3-D13 DASD drive 13 (5802 The disk unit has the same DSA as the 000900FF or 040900FF
only) storage IOA controlling it.
Ux-P3-D14 DASD drive 14 (5802 The disk unit has the same DSA as the 000A00FF or 040A00FF
only) storage IOA controlling it.
Ux-P3-D15 DASD drive 15 (5802 The disk unit has the same DSA as the 000B00FF or 040B00FF
only) storage IOA controlling it.
Ux-P3-D16 DASD drive 16 (5802 The disk unit has the same DSA as the 000C00FF or 040C00FF
only) storage IOA controlling it.
Ux-P3-D17 DASD drive 17 (5802 The disk unit has the same DSA as the 000D00FF or 040D00FF
only) storage IOA controlling it.
Ux-P3-D18 DASD drive 18 (5802 The disk unit has the same DSA as the 000E00FF or 040E00FF
only) storage IOA controlling it.

5803 and 5873 addresses

You can cross-reference a disk drive physical location code to the address.

Use the address to find the location for the system, then go to 5803 and 5873 on page 108 to find
additional location information.

Finding parts, locations, and addresses 133

Table 61. IOA, and device address information, running IBM i
Position Possible failing item DSA (BBBBCcbb) Unit address
Un-Px-C1 PCIe adapter aaaa-00-00 Not applicable
Un-Px-C2 PCIe adapter bbbb-00-00 Not applicable
Un-Px-C3 PCIe adapter cccc-00-00 Not applicable
Un-Px-C4 PCIe adapter dddd-00-00 Not applicable
Un-Px-C5 PCIe adapter eeee-00-00 Not applicable
Un-Px-C6 PCIe adapter ffff-00-00 Not applicable
Un-Px-C7 PCIe adapter gggg-00-00 Not applicable
Un-Px-C8 PCIe adapter hhhh-00-00 Not applicable
Un-Px-C9 PCIe adapter iiii-00-00 Not applicable
Un-Px-C10 PCIe adapter jjjj-00-00 Not applicable
Un-P3-D1 DASD drive 1 (5803 The disk unit has the same DSA as the 000600FF or 040600FF
only) storage IOA controlling it.
Un-P3-D2 DASD drive 2 (5803 The disk unit has the same DSA as the 000700FF or 040700FF
only) storage IOA controlling it.
Un-P3-D3 DASD drive 3 (5803 The disk unit has the same DSA as the 000800FF or 040800FF
only) storage IOA controlling it.
Un-P3-D4 DASD drive 4 (5803 The disk unit has the same DSA as the 000900FF or 040900FF
only) storage IOA controlling it.
Un-P3-D5 DASD drive 5 (5803 The disk unit has the same DSA as the 000A00FF or 040A00FF
only) storage IOA controlling it.
Un-P3-D6 DASD drive 6 (5803 The disk unit has the same DSA as the 000B00FF or 040B00FF
only) storage IOA controlling it.
Un-P3-D7 DASD drive 7 (5803 The disk unit has the same DSA as the 000C00FF or 040C00FF
only) storage IOA controlling it.
Un-P3-D8 DASD drive 8 (5803 The disk unit has the same DSA as the 000D00FF or 040D00FF
only) storage IOA controlling it.
Un-P3-D9 DASD drive 9 (5803 The disk unit has the same DSA as the 000E00FF or 040E00FF
only) storage IOA controlling it.
Un-P3-D10 DASD drive 10 (5803 The disk unit has the same DSA as the 000F00FF or 040F00FF
only) storage IOA controlling it.
Un-P3-D11 DASD drive 11 (5803 The disk unit has the same DSA as the 001000FF or 041000FF
only) storage IOA controlling it.
Un-P3-D12 DASD drive 12 (5803 The disk unit has the same DSA as the 001100FF or 041100FF
only) storage IOA controlling it.
Un-P3-D13 DASD drive 13 (5803 The disk unit has the same DSA as the 001200FF or 041200FF
only) storage IOA controlling it.
Un-P3-D14 DASD drive 14 (5803 The disk unit has the same DSA as the 000600FF or 040600FF
only) storage IOA controlling it.
Un-P3-D15 DASD drive 15 (5803 The disk unit has the same DSA as the 000700FF or 040700FF
only) storage IOA controlling it.
Un-P3-D16 DASD drive 16 (5803 The disk unit has the same DSA as the 000800FF or 040800FF
only) storage IOA controlling it.
Un-P3-D17 DASD drive 17 (5803 The disk unit has the same DSA as the 000900FF or 040900FF
only) storage IOA controlling it.

134 Finding parts, locations, and addresses

Table 61. IOA, and device address information, running IBM i (continued)
Position Possible failing item DSA (BBBBCcbb) Unit address
Un-P3-D18 DASD drive 18 (5803 The disk unit has the same DSA as the 000A00FF or 040A00FF
only) storage IOA controlling it.
Un-P3-D19 DASD drive 19 (5803 The disk unit has the same DSA as the 000B00FF or 040B00FF
only) storage IOA controlling it.
Un-P3-D20 DASD drive 20 (5803 The disk unit has the same DSA as the 000C00FF or 040C00FF
only) storage IOA controlling it.
Un-P3-D21 DASD drive 21(5803 The disk unit has the same DSA as the 000D00FF or 040D00FF
only) storage IOA controlling it.
Un-P3-D22 DASD drive 22 (5803 The disk unit has the same DSA as the 000E00FF or 040E00FF
only) storage IOA controlling it.
Un-P3-D23 DASD drive 23 (5803 The disk unit has the same DSA as the 000F00FF or 040F00FF
only) storage IOA controlling it.
Un-P3-D24 DASD drive 24 (5803 The disk unit has the same DSA as the 001000FF or 041000FF
only) storage IOA controlling it.
Un-P3-D25 DASD drive 25 (5803 The disk unit has the same DSA as the 001100FF or 041100FF
only) storage IOA controlling it.
Un-P3-D26 DASD drive 26 (5803 The disk unit has the same DSA as the 001200FF or 041200FF
only) storage IOA controlling it.

5886 addresses
You can cross-reference a disk drive physical location code to the address.

Use the address to find the location for the system, then go to 5886 on page 114 to find additional
location information.

Note: The x in the following table depends upon which I/O adapter port is used and can have values of
0, 4, or 8.
Table 62. Device address information
Physical location code Unit address
Un-P1-D1 0x0000FF
Un-P1-D2 0x0100FF
Un-P1-D3 0x0200FF
Un-P1-D4 0x0300FF
Un-P1-D5 0x0400FF
Un-P1-D6 0x0500FF
Un-P1-D7 0x0600FF
Un-P1-D8 0x0700FF
Un-P1-D9 0x0800FF
Un-P1-D10 0x0900FF
Un-P1-D11 0x0A00FF
Un-P1-D12 0x0B00FF

Finding parts, locations, and addresses 135

System parts
Use this information to locate and identify common hardware parts.

System parts contains only the part numbers likely to be needed during hardware servicing, and is not a
complete part number listing. Indexed assembly diagrams help you map the part to its position on the
unit. Use Part locations and location codes on page 2 to help you identify location codes.

8203-E4A, 8261-E4S, 9407-M15, and 9408-M25 system parts

Indexed drawings show parts system part numbers.

Rack assembly

Table 63. Rack assembly part numbers

Index CCIN Part number Units per Description
number assembly
1 44V4843 1 Left EIA bracket
2 09P3744 1 Screw, left EIA bracket
3 43W4518 1 Left slide assembly
4 39J4515 1 Drawer top cover 8203-E4A
4 53P0308 1 Drawer top cover 9408-M25

136 Finding parts, locations, and addresses

Table 63. Rack assembly part numbers (continued)
Index CCIN Part number Units per Description
number assembly
4 39J4515 1 Drawer top cover 9407-M15
5 43W4519 1 Right slide assembly
6 44V4840 1 Right EIA bracket
7 09P3744 1 Screw, right EIA bracket
8 39J4530 1 Drawer front bezel
9 04N6587 2 Drawer shipping screws

Stand-alone assembly

Table 64. Stand-alone assembly part numbers

Index CCIN Part number Units per Description
number assembly
1 44V3121 1 Left stand-alone cover 8203-E4A
1 53P0285 1 Left stand-alone cover 9408-M25

Finding parts, locations, and addresses 137

Table 64. Stand-alone assembly part numbers (continued)
Index CCIN Part number Units per Description
number assembly
1 44V3121 1 Left stand-alone cover 9407-M15
2 44V4936 1 Back stand-alone cover
3 42R8604 1 Handle cap
4 44V3127 1 Handle bracket
5 09P3744 4 Screw, handle bracket
6 44V3125 1 Right stand-alone cover 8203-E4A
6 39J1179 1 Right stand-alone cover 9408-M25
6 44V3125 1 Right stand-alone cover 9407-M15
7 09P3744 1 Screw, right stand-alone cover
8 and 9 42R6911 1 One piece front stand-alone bezel
10 44V3120 1 Tip foot
11 09P3744 4 Screw, tip foot

138 Finding parts, locations, and addresses

Rack assembly continued

Table 65. Rack assembly part numbers

Index CCIN Part number Units per Description
number assembly
1 28A8 46K6926 1 SATA media and 3.5 inch form factor disk drive
backplane
1 28A6 44V5927 1 SATA media and 3.5 inch form factor disk drive
backplane with SAS port expander
1 2893 07P6910 1 IDE media and 3.5 inch form factor disk drive
backplane
1 2875 46K6634 1 IDE media and 3.5 inch form factor disk drive
backplane with SAS port expander
2 2A16 74Y2244 1 SATA media and 2.5 inch form factor disk drive
backplane with SAS port expander
2 2A39 46K6948 1 SATA media and 2.5 inch form factor disk drive
backplane with SAS port expander
3 58B0 44V6821 18 69 GB small form factor solid-state SAS drive

Finding parts, locations, and addresses 139

Table 65. Rack assembly part numbers (continued)
Index CCIN Part number Units per Description
number assembly
3 198B 44V4429 18 69.7 GB 15 K small form factor SAS disk drive
3 44V4426 18 73.4 GB 15 K small form factor SAS disk drive
3 198C 44V6844 18 139 GB 15 K small form factor SAS disk drive
3 44V6845 18 146 GB 15 K small form factor SAS disk drive
3 42R8392 18 146.8 GB 10 K small form factor SAS disk drive
3 44V6833 18 300 GB 10 K small form factor SAS disk drive
4 58B0 44V6819 1-6 3.5-inch 69 GB solid-state SAS drive
4 433B 42R6690 16 70 GB 15 K SAS disk drive, System i
4 3646 10N7230 1-6 73 GB 15 K SAS disk drive, AIX and Linux
4 3646 10N7200 1-6 73 GB 15 K SAS disk drive, AIX and Linux
4 433C 42R6691 16 140 GB 15 K SAS disk drive, System i
4 3647 10N7204 1-6 146 GB 15 K SAS disk drive, AIX and Linux
4 3647 10N7232 1-6 146 GB 15 K SAS disk drive, AIX and Linux
4 433D 42R6692 16 283.7 GB 15 K SAS disk drive, System i
4 3648 10N7208 1-6 300 GB 15 K SAS disk drive, AIX and Linux
4 3648 10N7234 1-6 300 GB 15 K SAS disk drive, AIX and Linux
4 198E 44V4434 16 450 GB 15 K SAS disk drive, System i
4 44V4432 16 450 GB 15 K SAS disk drive, AIX and Linux
5 1 Removable media drive. See Managing DVD
drives.
Note: The backplane can be used to determine
whether the removable media drive is IDE or
SATA.
6 44V4749 1 Control panel
7 44V4195 2 Power supply
8 1 Tape drive. See Managing devices.

140 Finding parts, locations, and addresses

Rack assembly continued

Table 66. Rack assembly part numbers

Index CCIN Part number Units per Description
number assembly
9 57B8 44V3298 1 SAS RAID enablement card
10 57B7 1. 44V4192 1 1. RAID auxiliary cache card
2. 44V4145 2. Cache battery pack
11 2A0D 10N9718 1 Thermal management card (TPMD)
12 1819 10N9622 1 Quad 1 GB ethernet card
12 1830 10N9669 1 Dual 10 GB ethernet card
12 1818 10N9627 1 Dual 1 GB ethernet card
13 1814 07P6778 2 GX RIO G adapter
13 1817 46K6564 2 GX 12x InfiniBand adapter
13 52B4 45D3912 1 GX 12x InfiniBand adapter
13 52B4 45D5063 1 GX 12x InfiniBand adapter
14 39J4517 4 Blower assembly

Finding parts, locations, and addresses 141

Table 66. Rack assembly part numbers (continued)
Index CCIN Part number Units per Description
number assembly
15 1 Air plenum
Note: The air plenum is part of the chassis FRU
and cannot be ordered separately.

Rack assembly continued

Table 67. Rack assembly part numbers

Index CCIN Part number Units per Description
number assembly
16 39J4503 1 PCI guide
17 1 Line cord bracket
Note: The line cord bracket is part of the chassis
FRU and cannot be ordered separately.
18 39J4502 3 Long PCI divider
19 53P4325 1 Short PCI divider
20 42R5078 1 GX divider
21 46K4567 1 Chassis

142 Finding parts, locations, and addresses

Table 67. Rack assembly part numbers (continued)
Index CCIN Part number Units per Description
number assembly
22 44V3382 1 SAS cable, disk drive backplane to bulkhead
connector, 8203-E4A, 9408-M25
Note: This cable connects external SAS storage to
an internal controller.
22 44V5253 1 SAS cable, disk drive backplane to bulkhead
connector, 8203-E4A
Note: This cable is for split disk drive backplane.

Rack assembly continued

Table 68. Rack assembly part numbers

Index CCIN Part number Units per Description
number assembly
23 53DE 46K7784 1 1-core 4.2 GHz backplane 8203-E4A, 9407-M15
23 53DC 46K7778 1 2-core 4.2 GHz backplane 8203-E4A, 9408-M25
23 53EE 46K6957 1 2-core 4.7 GHz backplane 8203-E4A
23 53E0 46K7790 1 4-core 4.2 GHz backplane 8203-E4A

Finding parts, locations, and addresses 143

Table 68. Rack assembly part numbers (continued)
Index CCIN Part number Units per Description
number assembly
23 53ED 46K6966 1 4-core 4.7 GHz backplane 8203-E4A
24 52A9 10N6802 1 VPD card
25 44V6627 2 65 A VRM1 for processor 1 (used on 1-core
backplane only)
Note: Replace in pairs. Order two VRMs to form
a pair.
25 44V6625 2 95 A VRM1 for processor 1 (used on 2-core or
4-core backplanes only)
Note: Replace in pairs. Order two VRMs to form
a pair.
26 44V3841 1-2 30 A VRM2
27 44V6625 0-2 95 A VRM1 for processor 2 (used on 4-core
backplane only)
Note: Replace in pairs. Order two VRMs to form
a pair.
28 31A9 77P6497 8 512 MB 667 MHz RDIMM
28 31AA 77P6498 8 1 GB 667 MHz RDIMM
28 31AB 77P6499 8 2 GB 667 MHz RDIMM, 512 Mb DRAM
28 31AC 77P8030 8 2 GB 667 MHz RDIMM, 1 Gb DRAM
Note: A minimum system firmware level of
EL340_039_039 is required to support this
feature.
28 31A6 77P6500 8 4 GB 667 MHz RDIMM
28 31A8 77P7504 8 8 GB 400 MHz RDIMM

Table 69. Cables

CCIN Description Part number
1.5 meter InfiniBand cable 15R8139
3 meter InfiniBand cable 15R8140
10 meter InfiniBand cable 15R8141
Operator panel cable, drawer 42R6064
Operator panel cable, stand-alone 42R6066
USB long cable for operator panel 42R6068
SCSI cable 52G4233
SCSI2 cable 52G4291
3.7 meter cable 10N7158
8 meter cable 10N7159
10 meter HSL cable 39J2561
1 meter SAS 4x EE cable 44V4147
3 meter SAS 4x EE cable 44V4148
6 meter SAS 4x EE cable 44V4149
3 meter SAS X cable 44V4154
6 meter SAS X cable 44V4155

144 Finding parts, locations, and addresses

Table 69. Cables (continued)
CCIN Description Part number
15 meter SAS X cable 44V4156
1 meter SAS 4x AI cable 44V4041
3 meter SAS 4x AE cable 44V4163
6 meter SAS 4x AE cable 44V4164
1.5 meter SAS YI cable 44V4161
3 meter SAS YI cable 44V4162
1.5 meter SAS YO cable 44V4157
3 meter SAS YO cable 44V4158
6 meter SAS YO cable 44V4159
15 meter SAS YO cable 44V4160
10.5 inch SAS removable media device cable 42R5815
2 meter SPCN cable 22R5217
3 meter SPCN cable 22R5239
15 meter SPCN cable 22R5221
6 meter SPCN cable 22R5219
30 meter SPCN cable 22R5222

Table 70. Miscellaneous parts

CCIN Description Part number
External cables and cords See Site and hardware
planning.
Removable media See Managing devices.
PCI adapters See Managing PCI adapters.
Cable configuration See Enclosures and
expansion units.
Time-of-day battery 44V4359
Power supply filler 42R6935
4 MM cleaning tape 23R5638

8204-E8A and 9409-M50 system parts

Indexed drawings show parts system part numbers.

Finding parts, locations, and addresses 145

Rack final assembly

Table 71. Rack final assembly part numbers

Index CCIN Part number Units per Description
number assembly
1 39R6550 1 Rack mounting bracket kit 8204-E8A
1 42R8279 1 Left rack mounting bracket
2 39J3953 2 Screw
2 39R6550 1 Rack mounting bracket kit 8204-E8A
3 39J4471 1 Left rail 9409-M50
4 42R7686 1 Rack top cover 8204-E8A
4 21P4986 1 Rack top cover 9409-M50
5 39J4472 1 Right rail 9409-M50
6 42R8278 1 Right rack mounting bracket
7 39J3953 2 Screw
8 44V5078 1 Front bezel 8204-E8A
8 44V4987 1 Front bezel 9409-M50
9 12J5289 2 Screw

146 Finding parts, locations, and addresses

Stand-alone final assembly

Table 72. Stand-alone final assembly part numbers

Index CCIN Part number Units per Description
number assembly
1 44V2839 1 Left side cover 8204-E8A
1 39J1223 1 Left side cover 9409-M50
2 42R8604 1 Top handle cap
3 42R8601 1 Top handle assembly
4 09P3744 4 Screw
5 42R8598 1 Right side cover 8204-E8A
5 39J1224 1 Right side cover 9409-M50
6 09P3744 1 Screw
7&8 44V4989 1 Stand-alone bezel 8204-E8A
7&8 12R8505 1 Stand-alone bezel 9409-M50
9 42R5432 1 Tip foot assembly 8204-E8A
9 39J1235 1 Tip foot assembly 9409-M50

Finding parts, locations, and addresses 147

Table 72. Stand-alone final assembly part numbers (continued)
Index CCIN Part number Units per Description
number assembly
10 09P3744 4 Screw

Rack assembly detail

Table 73. Rack assembly detail part numbers

Index CCIN Part number Units per Description
number assembly
1 28A8 46K6926 1 SATA media and 3.5 inch form factor disk drive
backplane
1 28A6 44V5927 1 SATA media and 3.5 inch form factor disk drive
backplane with SAS port expander
1 2893 07P6910 1 IDE media and 3.5 inch form factor disk drive
backplane

148 Finding parts, locations, and addresses

Table 73. Rack assembly detail part numbers (continued)
Index CCIN Part number Units per Description
number assembly
1 2875 46K6634 1 IDE media and 3.5 inch form factor disk drive
backplane with SAS port expander
2 2A16 74Y2244 1 SATA media and 2.5 inch form factor disk drive
backplane with SAS port expander
2 2A39 46K6948 1 SATA media and 2.5 inch form factor disk drive
backplane with SAS port expander
3 58B0 44V6821 18 69 GB small form factor solid-state SAS drive
3 198B 44V4429 18 69.7 GB 15 K small form factor SAS disk drive
3 44V4426 18 73.4 GB 15 K small form factor SAS disk drive
3 198C 44V6844 18 139 GB 15 K small form factor SAS disk drive
3 44V6845 18 146 GB 15 K small form factor SAS disk drive
3 42R8392 18 146.8 GB 10 K small form factor SAS disk drive
3 44V6833 18 300 GB 10 K small form factor SAS disk drive
4 58B0 44V6819 1-6 3.5-inch 69 GB Solid-state drive
4 39J3695 16 3.5 inch 35 GB SCSI DASD 9409-M50, 15 K
39J3698
4 433B 42R6690 16 70 GB SAS disk drive
4 39J3696 16 3.5 inch 70 GB SCSI DASD 9409-M50, 15 K
39J3699
4 10N7230 1-6 3.5 inch 73 GB SAS DASD
4 10N7200 16 3.5 inch 73 GB SAS DASD 8204-E8A, 15 K
42R8391
4 03N5260 16 3.5 inch 73 GB SAS DASD 9409-M50, 10 K
4 433C 42R6691 16 140 GB SAS disk drive
4 39J3697 16 3.5 inch 140 GB SCSI DASD 9409-M50, 15 K
39J3700
4 10N7232 1-6 3.5 inch 146 GB SAS DASD, 15 K
4 10N7204 16 3.5 inch 146 GB SAS DASD 8204-E8A
42R8392
4 03N5265 16 3.5 inch 146 GB SAS DASD 9409-M50, 10 K
03N6330
4 03N5285 1-6 3.5 inch 146 GB SCSI DASD 9409-M50, 15 K
4 42R6676 16 3.5 inch 282 GB SAS DASD 9409-M50, 15 K
42R6677
4 433D 42R6692 16 283.7 GB SAS disk drive
4 10N7208 1-6 3.5 inch 300 GB SAS DASD, 15 K
4 10N7234 1-6 3.5 inch 300 GB SAS DASD, 15 K 8204-E8A
4 10N7211 1-6 3.5 inch 300 GB SAS DASD, 15 K9409-M50
10N8578
4 03N5270 1-6 3.5 inch 300 GB SAS DASD, 10K9409-M50
03N6335

Finding parts, locations, and addresses 149

Table 73. Rack assembly detail part numbers (continued)
Index CCIN Part number Units per Description
number assembly
5 1 Removable media drive. See Managing DVD
drives.
Note: The backplane can be used to determine
whether the removable media drive is IDE or
SATA.
6 296C 44V4749 1 Control panel
7 51C4 42R6607 2 1700 W dc power supply (8204-E8A)
7 51C3 44V4951 2 1700 W ac power supply
8 1 Tape drive. See Managing devices.

Rack assembly detail, continued

150 Finding parts, locations, and addresses

Table 74. Rack assembly detail, continued part numbers
Index CCIN Part number Units per Description
number assembly
9 44V3776 1 PCI divider
10 57B8 44V3298 1 RAID base card
11 57B7 44V3139 1 RAID cache card
11 74Y5667 1 RAID cache card battery
12 2A0E 10N9588 1 TPMD card
13 1814 07P6778 1 GX RIOG adapter
13 1817 46K6564 2 GX IB 12x adapter
13 52B4 45D3912 1 GX IB 12x adapter
13 52B4 45D5063 1 GX IB 12x adapter
14 44V3949 1 GX card divider
15 1818 10N9627 1 Dual 1 GB ethernet card
15 1819 10N9622 1 Quad 1 GB ethernet card
15 1830 10N9669 1 Dual 10 GB ethernet card
16 42R5805 2 GX support bracket
16 42R5807 2 GX Dual-Port 12X Channel Attach adapter
support bracket
16 42R5809 2 GX support bracket

Finding parts, locations, and addresses 151

Rack assembly detail, continued

Table 75. Rack assembly detail part numbers

Index CCIN Part number Units per Description
number assembly
17 44V3458 1 ac line cord box
18 NONUM 1 Fan cage
19 44V3455 1 Fan lattice
20 44V3454 4 Fan
21 53EC 46K7817 4 2-core 5.0 GHz processor
21 53E1 10N9725 4 2-core 4.2 GHz processor
21 53E1 46K7593 4 2-core 4.2 GHz processor
Note: See the IBM Prerequisite Web site at
http://www-912.ibm.com/e_dir/

eServerPrereq.nsf for minimum system

firmware requirements.
21 252F 07P6793 4 2-core 3.5 GHz processor

152 Finding parts, locations, and addresses

Table 75. Rack assembly detail part numbers (continued)
Index CCIN Part number Units per Description
number assembly
21 252F 46K7590 4 2-core 3.5 GHz processor
Note: See the IBM Prerequisite Web site at
http://www-912.ibm.com/e_dir/

eServerPrereq.nsf for minimum system

firmware requirements.

Rack assembly detail, continued

Table 76. Rack assembly detail part numbers

Index CCIN Part number Units per Description
number assembly
22 28A3 46K6726 1 System backplane, 3.5 and 4.2 GHz processor
22 2B3E 46K7761 1 System backplane, 3.5, 4.2, and 5.0 GHz
processor

Finding parts, locations, and addresses 153

Table 76. Rack assembly detail part numbers (continued)
Index CCIN Part number Units per Description
number assembly
23 NONUM 9 Backplane screw
24 NONUM 1 Front processor support
25 NONUM 5 Screw
26 NONUM 1 Card support divider
27 NONUM 1 Screw
28 42R5751, 1 SAS cable, DASD backplane to bulkhead
connector (external)
28 44V5252 1 SAS cable, DASD backplane to bulkhead
connector, split DASD backplane
functionality8204-E8A

Rack assembly detail, continued

154 Finding parts, locations, and addresses

Table 77. Rack assembly detail part numbers, continued.
Index CCIN Part number Units per Description
number assembly
27 44V4619 1 DIMM duct plate
28 39J2038 Screw
29 2A29 44V5183 2 Voltage regulator 95 A (VRM1A, VRM1B)
Note: Replace in pairs. Order two VRMs to form
a pair.
30 1 Smart card
31 31A9 77P6497 2-8 512 MB 667 MHz RDIMM
31 31AA 77P6498 2-8 1 GB 667 MHz RDIMM
31 31AB 77P6499 2-8 2 GB 667 MHz RDIMM, 512Mb DRAM
31 31AC 77P8030 2-8 2 GB 667 MHz RDIMM, 1Gb DRAM
Note: A minimum system firmware level of
EL340_039_039 is required to support this
feature.
31 31A6 77P6500 2-8 4 GB 667 MHz RDIMM
31 31A8 77P7504 2-8 8 GB 400 MHz RDIMM
31 77P5883 28 512 MB DIMM for integrated xSeries server
31 77P5880 28 1 GB DIMM for integrated xSeries server
32 2A2C 42R6498 1 Voltage regulator 30 A (VRM2)
32 2A2C 42R8609 1 Voltage regulator 30 A (VRM2)

Table 78. Processors

CCIN Description Part number
252F 2-core 3.5 GHz POWER6 Processor Card 46K7590
53E1 2-core 4.2 GHz POWER6 Processor Card 46K7593
53EC 2-core 5.0 GHz POWER6 Processor Card 46K7401

Table 79. Cables

CCIN/CIN Description Part number
.6 meter InfiniBand cable 42V2129
1 meter SAS cable 8204-E8A 44V4147
1.5 meter GX Dual-Port 12X Channel Attach adapter to GX cable 15R8139
1.5 meter InfiniBand cable 42V2130
2 meter SPCN cable 22R5217
6006 3 meter SPCN cable 22R5239
3 meter SAS cable 8204-E8A 44V4148
1482 3.5 meter RIO-2 cable 39J2554
3 meter InfiniBand cable 42V2132
3 meter InfiniBand cable, DDR 15R8140

Finding parts, locations, and addresses 155

Table 79. Cables (continued)
CCIN/CIN Description Part number

System p5 6 meter SPCN cable 22R5219
model: 1464,
System i5 and
System p5
models: 6008
8 meter InfiniBand cable 42R6160
10 meter InfiniBand cable 15R8141 8204-E8A
1483 10 meter RIO 39J2561
10.5 inch removable media drive SAS cable for tape drive 42R5815
System i5 model: 15 meter SPCN cable 22R5221
1465, System p5
model: 6007
System i5 model: 30 meter SPCN cable 22R5222
1466, System i5
and System p5
models: 6029
SCSI2 cable 52G4291
SCSI cable 52G4233
SCSI cable 42R4756
Serial cable 10N6535
Operator panel round cable 42R6069
Operator panel flat ribbon cable 42R6064

Table 80. Miscellaneous parts

CCIN Description Part number
Removable media See Managing devices.
External cables and cords See Site and hardware
planning.
Cable configuration See Enclosures and
expansion units.
PCI adapters See Managing PCI adapters.
VPD card, CCIN 52AE 10N8696
Wrap plug 12R9314
Wrap plug 03N6070 8204-E8A
Wrap plug 87H3439
Wrap plug 87H3442
Wrap plug 93H5270
Wrap plug 87H3588
Wrap plug 12R9315
Wrap plug 42R4761
Wrap plug 87H3311
Wrap plug 33F8985
Wrap plug 73H2508

156 Finding parts, locations, and addresses

Table 80. Miscellaneous parts (continued)
CCIN Description Part number
282A Backplane, feature 5790 80P6626
Power supply filler 44V4069
Battery 16G8095

8234-EMA, 9117-MMA, and 9406-MMA

Indexed drawings show parts system part numbers.

Note: When upgrading, make sure DIMM is compatible with the system's Firmware level.

Cover assemblies

Table 81. Cover assembly part numbers

Index CCIN Part number Units per Description
number assembly
1 44V4751 Front cover assembly
2 44V2831 1 Front cover mounting bracket
Note: This assembly part number is for reference
only and cannot be ordered.
3 44V2830 2 Front cover mounting bracket screw
Note: This assembly part number is for reference
only and cannot be ordered.
4 42R8205 1 Rail kit (includes chassis tie-down)
5

Finding parts, locations, and addresses 157

Final assembly (back)

Table 82. Assembly

Index CCIN Part number Units per Description
number assembly
1 293B 44V4584 1 I/O backplane
2 294E 1. 46K7197 1 1. Service processor assembly
2. 16G8095 2. Battery
3 44V7309 2 Power supply 1600 W
4 1800 10N9921 2 RIO/HSL card assembly
4 1802 42R6849 2 12X Channel Interface card assembly
5 42R4190 1 PCI adapter cassette, Gen 3 single wide (handle
at bottom), short
5 42R4007 1 PCI adapter cassette, Gen 3 single wide (handle
at bottom), long
5 16R0091 1 PCI adapter cassette, Gen 2.x (handle at top), all
5 42R4008 1 PCI adapter cassette, Gen 3 double wide (handle
at bottom), long
6 52AD 10N6883 1 VPD card (MMA only)
6 52B8 46K6984 1 VPD card (EMA only)
7 181A 42R6775 Feature 5636 VPD pass-through card. This card provides
connection for the system VPD card, system
ports, and SPCN cable.1 GB ethernet
7 181C 42R7000 Feature 5639 VPD pass-through card. This card provides
connection for the system VPD card, system
ports, and SPCN cable. 1 GB ethernet quad

158 Finding parts, locations, and addresses

Table 82. Assembly (continued)
Index CCIN Part number Units per Description
number assembly
7 181B 07P6931 Feature 5637 VPD pass-through card. This card provides
connection for the system VPD card, system
ports, and SPCN cable. 10 GB ethernet long
range

Final assembly (front)

Finding parts, locations, and addresses 159

Table 83. Final assembly (front)
Index CCIN Part number Units per Description
number assembly
1 39J0859 2 Fan assembly
2 293D 46K4829 1 IDE removable media enclosure assembly
(includes the media backplane)
2 297D 46K7054 1 SATA removable media enclosure assembly
(includes the media backplane)
3 1 Removable media. See Managing devices.
4 28D4 10N9964 1 Control panel assembly
4 39J1301 1 Control panel filler
5 44V5648 3 Voltage regulator assembly for four core
processor (EMA or MMA with feature code 7540
and CCIN 53EB)
5 44V5705 3 Voltage regulator assembly for two core
processor (MMA only)

Table 84. Final assembly part numbers (continued)

Index CCIN Part number Units per Description
number assembly
6 293C 10N9617 1 Disk drive backplane (used with CCIN 293D
removable media backplane)
6 290C 46K7048 1 Disk drive backplane (used with CCIN 290C
removable media backplane)
7 58B0 44V6819 69 GB Solid-state drive
7 39J3695 35 GB SCSI disk drive
39J3698

160 Finding parts, locations, and addresses

Table 84. Final assembly part numbers (continued) (continued)
Index CCIN Part number Units per Description
number assembly
7 433B 42R6690 70 GB SAS disk drive
7 39J3699 70 GB SCSI disk drive
39J3696
7 10N7200 73 GB SAS disk drive
10N7230
7 39J3700 140 GB SCSI disk drive
39J3697
7 433C 42R6691 140 GB SAS disk drive
7 10N7232 146 GB SAS disk drive
10N7204
7 42R6676 282 GB SAS disk drive
42R6677
7 433D 42R6692 283.7 GB SAS disk drive
7 10N7208 300 GB SAS disk drive
10N7234
8 27B7 10N9600 1 System processor backplane for four core
processor
8 27B0 03N6902 1 System processor backplane for two core
processor
9 53D8 10N8029 3.5 GHz two core processor card POWER6, 12
DDR2 memory slots
9 53F1 46K6894 3.6 GHz four core processor card POWER6, 12
DDR2 memory slots (EMA only)
9 53CD 10N8339 4.2 GHz two core processor card POWER6, 8
DDR2 memory slots
9 53D7 10N8023 4.2 GHz two core processor card POWER6, 12
DDR2 memory slots
9 53CF 03N4468 4.7 GHz two core processor card POWER6, 12
DDR2 memory slots
9 53EB 10N8325 4.2 GHz four core processor card POWER6, 12
DDR2 memory slots (MMA only)
9 53EA 46K6624 4.4 GHz two core processor card POWER6, 12
DDR2 memory slots
9 53E9 46K6621 5.0 GHz two core processor card POWER6, 12
DDR2 memory slots
9 319B 15R7433 512 MB, DDR2, 667 MHz (MMA only)
9 31B5 45D1178 512 MB, DDR2, 667 MHz (MMA only)
9 30F0 12R8540 512 MB, DDR2, 533 MHz, used in processor
feature code 5621, CCIN 53CD (MMA only)
9 319C 15R7436 1 GB, DDR2, 667 MHz (MMA only)
9 30F2 12R8544 1 GB, DDR2, 533 MHz, used in processor feature
code 5621, CCIN 53CD (MMA only)
9 31B6 45D1670 1 GB, DDR2, 667 MHz, replaces 319C (EMA and
MMA)

Finding parts, locations, and addresses 161

Table 84. Final assembly part numbers (continued) (continued)
Index CCIN Part number Units per Description
number assembly
9 316F 41V0128 1-2 GB, CUoD, DDR2, 533 MHz, used in
processor feature code 5621, CCIN 53CD (MMA
only)
9 30F3 16R1530 2 GB, DDR2, 533 MHz, used in processor feature
code 5621, CCIN 53CD (MMA only)
9 319E 15R7439 2 GB, DDR2, 667 MHz (MMA only)
9 31B7 45D1672 2 GB, DDR2, 667 MHz, replaces 319E (EMA and
MMA)
9 320B 45D3365 2 GB, DDR2, 667 MHz (EMA only)
9 314E 12R9574 2-4 GB, CUoD, DDR2, 533 MHz, used in
processor feature code 5621, CCIN 53CD (MMA
only)
9 314A 12R8467 4 GB, DDR2, 400 MHz, used in processor feature
code 5621, CCIN 53CD (MMA only)
9 312F 12R8994 4 GB, DDR2, 533 MHz, used in processor feature
code 5621, CCIN 53CD (MMA only)
9 319D 15R7445 4 GB, DDR2, 533 MHz (MMA only)
9 31B9 45D1199 4 GB, DDR2, 533 MHz, replaces 319D (EMA and
MMA)
9 320C 45D3367 4 GB, DDR2, 533 MHz (EMA only)
9 319F 15R9379 8 GB, DDR2, 400 MHz, low current (FC 5696 on
MMA only)
9 31B3 45D1787 8 GB, DDR2, 400 MHz (FC 5690 on EMA and
MMA)
9 31BA 45D1205 8 GB, DDR2, 400 MHz, low current, replaces
319F (FC 5696 on EMA and MMA)
9 31BC 45D1208 8 GB, DDR2, 400 MHz, high current, replaces
31BD (FC 5696 on EMA and MMA)
9 31BD 45D0635 8 GB, DDR2, 400 MHz, high current (FC 5696 on
MMA only)
9 320E 45D3369 8 GB, DDR2, 400 MHz (EMA only)

Table 85. Cables

CCIN Description Part number
SMP 2 drawer cable 42R8112
SMP 3 drawer cable 42R8113
SMP 4 drawer cable 42R8114
FSP 2 drawer cable 42R6043
FSP 3 drawer cable 42R6044
FSP 4 drawer cable 42R6045
SPCN cable assembly, base 41L5650
SPCN 2 meter cable 22R5217
SPCN 3 meter cable 22R5239
SPCN 6 meter cable 22R5219

162 Finding parts, locations, and addresses

Table 85. Cables (continued)
CCIN Description Part number
SPCN 15 meter cable 22R5221
SPCN 30 meter cable 22R5222
SPCN power to blower cable 42R4035
Control panel cable 41L5649
Control panel cable 42R4032
SCSI cable, bus base 42R4034
1 meter SCSI cable 41Y0596
3 meter SCSI cable 41Y0597
5 meter SCSI cable 41Y0598
10 meter SCSI cable 41Y0599
20 meter SCSI cable 41Y0600
SCSI expansion cable 42R4049
42R4050
1 meter GX Dual-Port 12X Channel Attach adapter cable 44V3422
2 meter GX Dual-Port 12X Channel Attach adapter cable 44V3424
3 meter GX Dual-Port 12X Channel Attach adapter cable 44V3426
3 meter GX Dual-Port 12X Channel Attach adapter to InfiniBand 15R8140
4X cable
10 meter GX Dual-Port 12X Channel Attach adapter to InfiniBand 15R8141
4X cable
Split disk backplane cable card for a 6/0 split 44V3435
1 meter SAS 4x AI cable 44V4041
1 meter SAS 4x EE cable 44V4147
3 meter SAS 4x EE cable 44V4148
3 meter SAS X cable 44V4154
3 meter SAS YO cable 44V4158
3 meter SAS 4x AE cable 44V4163
6 meter SAS 4x EE cable 44V4149
6 meter SAS X cable 44V4155
6 meter SAS YO cable 44V4159
6 meter SAS 4x AE cable 44V4164
15 meter SAS X cable 44V4156
15 meter SAS YO cable 44V4160
6 meter RIO G cable 39J2559
10 meter RIO G cable 39J2561
15 meter RIO G cable 21P5457

Table 86. Keyboard parts

CCIN Description Part number
2890-002 Keyboard, US English 89P9240

Finding parts, locations, and addresses 163

Table 86. Keyboard parts (continued)
CCIN Description Part number
101 key keyboard 82G3278
1392090
1394609
102 key keyboard problem 8131596
keyboard, Arabic
Keyboard, Arabic (ID 238) 93H8125
Keyboard, Belgium-French (ID 120) 93H8127
Keyboard, Belgium-Dutch 1391414
Keyboard, Belgium-French 1391526
Keyboard, Belgium-French (ID 120) 93H8126
Keyboard, Brazilian Portuguese 64F7707
Keyboard, Brazilian Portuguese (ID 275) 93H8124
Keyboard, Bulgarian 1399583
Keyboard, Bulgarian (ID 442) 93H8128
Keyboard, Chinese/US (ID 467) 93H8155
Keyboard, Czechoslovakian 1399570
Keyboard, Czechoslovakian (ID 243) 93H8129
Keyboard, Danish 1391407
Keyboard, Danish (ID 159) 93H8130
Keyboard, Dutch (ID 143) 93H8131
Keyboard, Dutch/Netherlands 1391511
Keyboard, Finnish/Swedish 1391411
Keyboard, French 1391402
Keyboard, French(ID 189) 93H8132
Keyboard, French-Canadian 82G3279
Keyboard, French-Canadian 93H8121
(ID 058) 93H8122
Keyboard, French-Canadian
(ID 445)
Keyboard, German (ID 129) 93H8133
Keyboard, German/Austrian 1391403
Keyboard, Greek 1399046
Keyboard, Greek (ID 129) 93H8134
Keyboard, Hebrew 1391408
Keyboard, Hebrew (ID 212) 93H8135
Keyboard, Hungarian 1399581
Keyboard, Hungarian (ID 208) 93H8136
102 key keyboard problem Keyboard, Icelandic 1391407
Keyboard, Icelandic (ID 197) 93H8137
Keyboard, Italian 1393395
Keyboard, Italian (ID 142) 93H8138
Keyboard, Korea (ID 413) 93H8156

164 Finding parts, locations, and addresses

Table 86. Keyboard parts (continued)
CCIN Description Part number
Keyboard, Latin American (Spanish) 82G3292
Keyboard, Latvia (ID 234) 93H8152
Keyboard, Norwegian 1391409
Keyboard, Norwegian (ID 155) 93H8139
Keyboard, Portuguese 1391410
Keyboard, Polish 1399580
Keyboard, Polish (ID 214) 93H8140
Keyboard, Portuguese (ID 163) 93H8141
Keyboard, Romania 1399582
Keyboard, Romania (ID 446) 93H8142
Keyboard, Russian 1399579
Keyboard, Russian (ID 443) 93H8143
Keyboard, Serbian (ID 118) 93H8144
Keyboard, Slovak 1399571
Keyboard, Slovak (ID 245) 93H8145
Keyboard, Spanish 1391405
Keyboard, Spanish (ID 171) 93H8123
Keyboard, Spanish (ID 172) 93H8146
Keyboard, Sweden/Finland (ID 153) 93H8147
Keyboard, Swiss-French 1395881
Keyboard, Swiss French/German (ID 150) 93H8148
Keyboard, Swiss-German 1395882
Keyboard, Thailand (ID 191) 93H8157
Keyboard, Turkish (ID 179) 1393286
Keyboard, Turkish (ID 179) 93H8149
Keyboard, Turkish (ID 440) 8125409
Keyboard, Turkish (ID 440) 93H8150
Keyboard, U.K. English 1391406
Keyboard, Turkish (ID 166) 93H8151
Keyboard, US English ISO9995 (ID 103P) 93H8153
Keyboard, 106 Japan (ID 194) 93H8154
106 keys International 1392090
keyboard problem 79F0167
keyboard, Chinese 66G0507
keyboard, Japanese-Kanji 06H5286
Japanese, Enhanced 02G7353
keyboard, Korean
keyboard, Taiwanese
Lighted program function 39F8226
keyboard 39F8302
(LPFK), 6094 model 20
cable, serial attachment,
power

Finding parts, locations, and addresses 165

Table 86. Keyboard parts (continued)
CCIN Description Part number
Keyboard, English 10N6956
Keyboard, French (id 189) 10N6957
Keyboard, French (id 142) 10N6958
Keyboard, German 10N6959
Keyboard, UK English (id 166) 10N6960
Keyboard, Spanish (id 172) 10N6961
Keyboard, Japanese (id 184) 10N6962
Keyboard, Brazilian Portuguese (id 275) 10N6963
Keyboard, Canadian French (id 58) 10N6968
Keyboard, Belgium Dutch (id 120) 10N6969
Keyboard, Swedish Finnish (id 153) 10N6970
Keyboard, Danish (id 159) 10N6971
Keyboard, Bulgarian (id 442) 10N6972
Keyboard, Swiss French German (id 150) 10N6973
Keyboard, Norwegian (id 155) 10N6974
Keyboard, Portuguese (id 163) 10N6976
Keyboard, Greek (id 319) 10N6977
Keyboard, Hebrew (id 312) 10N6978
Keyboard, Hungarian (id 208) 10N6964
Keyboard, Polish (id 214) 10N6979
Keyboard, Slovakian (id 245) 10N6980
Keyboard, Czechoslovakian (id 245) 10N6981
Keyboard, Turkish (id 179) 10N6982
Keyboard, Spanish (id 171) 10N6983
Keyboard, Arabic (id 238) 10N6984
Keyboard, Korean (id 413) 10N6965
Keyboard, Chinese (id 467) 10N6966
Keyboard, French Canadian (id 445) 10N6967
Keyboard, Thailand (id 191) 10N6985
Keyboard, Russian (id 443) 10N6986
Keyboard, Yugoslavian Latin (id 105) 10N6987
Keyboard, English (EMEA) (id 103P) 10N6988
Keyboard, Dutch 10N6975
Keyboard 40K9430
Keyboard 40K9430
Keyboard 32N1205
Keyboard, French 32N1206
Keyboard, Italy 32N1207
Keyboard, Germany and Austria 32N1208
Keyboard, UK English 32N1209

166 Finding parts, locations, and addresses

Table 86. Keyboard parts (continued)
CCIN Description Part number
Keyboard, Spanish 32N1210
Keyboard, Japan 32N1211
Keyboard, Brazil 32N1212
Keyboard, Hungry 32N1213
Keyboard, Korea 32N1214
Keyboard, China 32N1215
Keyboard, French Canadian 32N1216
Keyboard, French Canadian 32N1217
Keyboard, Belgium and UK 32N1218
Keyboard, Sweden and Finland 32N1219
Keyboard, Danish 32N1220
Keyboard, Bulgaria 32N1221
Keyboard, Swiss, French, and German 32N1222
Keyboard, Norwegian 32N1223
Keyboard, Hebrew 32N1227
Keyboard, Poland 32N1228
Keyboard, Slovakian 32N1229
Keyboard, Czechoslovakia 32N1230
Keyboard, Turkey 32N1231
Keyboard, Latin Spanish 32N1232
Keyboard, Arabic 32N1233
Keyboard, Thailand 32N1234
Keyboard, Russia 32N1235
Keyboard, Slovakian 32N1236
Keyboard, English Europe 32N1237

Table 87. Miscellaneous parts

CCIN Description Part number
Removable media See Managing devices.
External cables and cords See Site and hardware
planning.
Cable configuration See Enclosures and expansion
units.
PCI adapters See Managing PCI adapters.
Black mouse 03N6669

Finding parts, locations, and addresses 167

Table 87. Miscellaneous parts (continued)
CCIN Description Part number
Wrap plug 12R9314
12R9315
42R4761
6165899
73H2508
87H3311
87H3439
87H3442
93H5270
03N6070

168 Finding parts, locations, and addresses

9119-FHA system parts
Indexed drawings show parts system part numbers.

Table 88. Final assembly (assembly 1)

Index number CCIN Part number Units Description
1 45D0629 1 Cover assembly, left side

Finding parts, locations, and addresses 169

Table 88. Final assembly (assembly 1) (continued)
Index number CCIN Part number Units Description
2 2665528 6 Screw
3 42V2119 6 J-bracket assembly, side cover
4 2665528 12 Screw
5 41U0400 1 Acoustic rear cover
6 45D0628 1 Cover assembly, right side
7 2665528 6 Screw
8 2665525 4 Screw
9 41V2376 2 Latch bracket
10 1 Acoustic front cover

Table 89. Final assembly (assembly 2)

Index number CCIN Part number Units Description
1 45D2463 2 BPE assembly
2 77G0599 10 Screw
3 74F1823 10 Nut clip
4 41V2374 AR BPF assembly
4 41V2453 AR BPF filler plate, front only
5 15R9306 2 Cable bracket assembly
6 77G0599 6 Screw
7 45D1471 2 Bulk power hub (BPH)

170 Finding parts, locations, and addresses

Table 89. Final assembly (assembly 2) (continued)
Index number CCIN Part number Units Description
8 45D1601 AR BPD assembly
8 31L8609 AR BPD filler assembly
9 45D1600 2 BPC assembly
10 45D0639 AR BPR assembly
10 15R7647 AR BPR filler assembly

Finding parts, locations, and addresses 171

Table 90. Final assembly (assembly 3)
Index number CCIN Part number Units Description
1 15R7120 1 Light strip, front
2 45D1117 4 Actuator assembly, top
2 45D2806 4 Actuator assembly, bottom

172 Finding parts, locations, and addresses

Table 90. Final assembly (assembly 3) (continued)
Index number CCIN Part number Units Description
3 45D1706 8 Node lock assembly
4 44P2994 AR Filler plate
5 77G0599 4 Screw
6 74F1823 4 Nut clip
7 44P2462 AR Filler plate
8 77G0599 2 Screw
9 74F1823 2 Nut clip
10 45D1981 8 Node locking bracket assembly, front
11 60H3940 AR Node assembly, unpopulated
11 60H4167 AR Node assembly, populated, 4.2 GHz
11 60H4168 AR Node assembly, populated, 5 GHz
12 15R7507 AR Node filler assembly
13 45D0534 AR EMI cover

Table 91. Final assembly (assembly 4)

Index number CCIN Part number Units Description
14 45D0802 1 UEPO assembly
15 2665528 2 Screw
16 15R9219 4 Actuator assembly, top
17 45D1044 4 Actuator assembly, bottom

Finding parts, locations, and addresses 173

Table 91. Final assembly (assembly 4) (continued)
Index number CCIN Part number Units Description
18 2C01 60H4138 2 FSP card
19 60H3792 2 Clock card
20 60H4148 1 System midplane
21 1624790 2 Screw, backplane mounting

174 Finding parts, locations, and addresses

Table 92. Final assembly (assembly 5)
Index number CCIN Part number Units Description
22 Not field 8 Node locking bracket assembly, back
stocked

Finding parts, locations, and addresses 175

Table 92. Final assembly (assembly 5) (continued)
Index number CCIN Part number Units Description
23 44P2994 AR Filler plate
23 44P2462 AR Filler plate
24 77G0599 4 Screw
25 74F1823 4 Nut clip
26 45D1140 AR MDA-EZ assembly
27 15R8873 AR Blower assembly
28 15R7121 1 Light strip, rear
29 15R8837 1 Node service cover
30 45D2720 1 Node service cover

Table 93. Final assembly (assembly 6)

Index number CCIN Part number Units Description
1 45D2491 AR DCA assembly
2 No num 1 Node assembly
3 60H4202 AR Processor assembly, 4.2 GHz
3 60H4203 AR Processor assembly, 5 GHz
4 41V0922 AR Book filler assembly
5 295A 45D1902 AR I/O hub card
5 295B 45D2593 AR GX Dual-Port 12X Channel Attach adapter
6 41T8593 AR Memory DIMM, 4 GB double high
6 15R9372 AR Memory DIMM, 8 GB double high

176 Finding parts, locations, and addresses

Table 93. Final assembly (assembly 6) (continued)
Index number CCIN Part number Units Description
7 45D1666 AR Memory DIMM, 1 GB single high
7 45D1668 AR Memory DIMM, 2 GB single high

Table 94. Cables

CCIN Part number Description
95P4084 SAS cable
44V4041 1 meter SAS cable
44V4147 1 meter SAS cable
44V4817 2 meter SAS cable
44V4148 3 meter SAS cable
44V4154 3 meter SAS cable
44V4158 3 meter SAS cable
44V4163 3 meter SAS cable
44V4149 6 meter SAS cable
44V4155 6 meter SAS cable
44V4159 6 meter SAS cable
44V4164 6 meter SAS cable
44V4156 15 meter SAS cable
44V4160 15 meter SAS cable
52G4233 SCSI cable
41Y0596 1 meter SCSI cable
41Y0597 3 meter SCSI cable
41Y0598 5 meter SCSI cable
41Y0599 10 meter SCSI cable
41Y0600 20 meter SCSI cable
22R5217 2 meter SPCN cable
22R5239 3 meter SPCN cable
036A 39J5820 3 meter SPCN cable
22R5219 6 meter SPCN cable
22R5221 15 meter SPCN cable
22R5222 30 meter SPCN cable
39J2561 10 meter HSL2 cable
42V2129 .6 meter 12X IB cable
42V2131 2.5 meter 12X IB cable
42R6160 8 meter 12X IB cable
32N1311 2 meter external cable
31P6132 8 meter cable
41V2507 BPCA TO BPCB cable
41V2508 BPCA TO BPCB power cable
15R6779 Bulk power distribution cable

Finding parts, locations, and addresses 177

Table 94. Cables (continued)
CCIN Part number Description
15R6780 Bulk power distribution cable
41V2172 Bulk power regulator cable
41V0570 IBF cable
39J5836 UPS adapter cable
95P4049 DVD cable
11P4606 Cable clamp
0524519 Cable tie
15R8270 Cable tool
095P4048 VPD cable

Table 95. Keyboards

CCIN Part number Description
10N6984 Keyboard, Arabic
32N1233 Keyboard, Arabic
32N1212 Keyboard, Brazilian
10N6963 Keyboard, Brazilian/Portuguese
10N6972 Keyboard, Bulgarian
32N1221 Keyboard, Bulgarian
32N1217 Keyboard, CANFRC
32N1215 Keyboard, Chinese
10N6966 Keyboard, Chinese/US
10N6981 Keyboard, Czechoslovakian
32N1230 Keyboard, Czechoslovakian
10N6971 Keyboard, Danish
32N1220 Keyboard, Danish
32N1206 Keyboard, French
10N6957 Keyboard, French
10N6967 Keyboard, French Canadian
10N6968 Keyboard, French Canadian
32N1216 Keyboard, French Canadian
10N6973 Keyboard, French/German
10N6959 Keyboard, German
32N1208 Keyboard, German
10N6977 Keyboard, Greek
32N1226 Keyboard, Greek
10N6978 Keyboard, Hebrew
32N1227 Keyboard, Hebrew
10N6964 Keyboard, Hungarian
32N1213 Keyboard, Hungarian
10N6958 Keyboard, Italian

178 Finding parts, locations, and addresses

Table 95. Keyboards (continued)
CCIN Part number Description
32N1207 Keyboard, Italian
32N1211 Keyboard, Japanese
10N6962 Keyboard, Japanese
32N1214 Keyboard, Korean
10N6965 Keyboard, Korean
10N6983 Keyboard, LA Spanish
32N1232 Keyboard, LA Spanish
10N6974 Keyboard, Norwegian
32N1223 Keyboard, Norwegian
10N6979 Keyboard, Polish
32N1228 Keyboard, Polish
10N6975 Keyboard, Portuguese
10N6976 Keyboard, Portuguese
32N1224 Keyboard, Portuguese
32N1225 Keyboard, Portuguese
10N6986 Keyboard, Russian
32N1235 Keyboard, Russian
10N6980 Keyboard, Slovakia
32N1229 Keyboard, Slovakia
32N1236 Keyboard, Slovakia
10N6961 Keyboard, Spanish
32N1210 Keyboard, Spanish
10N6970 Keyboard, Sweden/Finland
32N1219 Keyboard, Sweden/Finland
32N1234 Keyboard, Thailand
10N6985 Keyboard, Thailand
10N6982 Keyboard, Turkey
32N1231 Keyboard, Turkey
10N6960 Keyboard, United Kingdom
32N1209 Keyboard, United Kingdom
10N6956 Keyboard, United Kingdom
10N6988 Keyboard, US EMEA
32N1205 Keyboard, US
10N6987 Keyboard, Yugoslavian/Latin

Table 96. Miscellaneous parts

CCIN Part number Description
External cables See Site and hardware planning.
and cords
Cable See Enclosures and expansion units.
configuration

Finding parts, locations, and addresses 179

Table 96. Miscellaneous parts (continued)
CCIN Part number Description
PCI adapters See Managing PCI adapters.
Removable See Managing devices.
media
45D2299 1/4 inch (8 MM) drive socket
45D0424 3/8 inch drive extension
31BA 45D1205 8 GB DIMM, 400 MHz DDR2
87H3621 8 MB DIMM
31B4 45D1426 16 GB DIMM, DDR2, 400 MHz
316C 41V2097 0-16 GB CUoD DIMM
316B 41V2095 0-8 GB CUoD DIMM, DDR2
319D 15R7445 4 GB DIMM, DDR2, 533 MHz
319F 15R9379 8 GB DIMM, DDR2, 400 MHz
45D2504 4 MM socket driver
03N5265 146 GB DASD, 10 K RPM
03N6330 146 GB DASD, 10 K RPM
03N5285 3.5 inch 146 GB SCSI DASD, 15 K RPM
10N7232 146 GB SAS DASD, 15 K RPM
10N7204 146 GB SAS DASD, 15 K RPM, 3.5 inch
15R7322 19 inch acoustic cover kit
39R6550 2U rail kit
10N7211 300 GB DASD, 15 K RPM
10N8578 300 GB DASD, 15 K RPM
03N5270 300 GB DASD, DASD, 10 K RPM
03N6335 300 GB DASD, DASD, 10 K RPM
10N7208 300 GB DASD, SAS, 15 K RPM, 3.5 inch
10N7234 300 GB SAS DASD, 15 K RPM
23R5638 4 MM cleaning cartridge
44P2809 42U frame
15R7659 61R UEPO switch
03N5260 73 GB DASD, 10 K RPM
10N7200 73 GB SAS DASD, 15 K RPM
10N7230 73 GB SAS DASD, 15 K RPM
45D0417 8 MM socket
23R5635 80 GB cartridge
95P4436 800 GB cartridge
41U0389 Acoustic cover
41U0388 Acoustic door
45D2505 Actuator tool
45D2300 Adapter, 3/8 inch adapter to 1/4 inch
41V0606 Adapter bracket

180 Finding parts, locations, and addresses

Table 96. Miscellaneous parts (continued)
CCIN Part number Description
10N8625 Adapter bracket
31L8613 Air baffle
12R9301 Air feeder
12R8263 Applicator
42R4037 Assembly filler
95P4075 Base unit
39J5555 Battery
41U0012 Battery
11P3745 Battery retainer bracket, inner
11P3746 Battery retainer bracket, outer
23R5633 Bezel
39R6583 Bezel left
39R6584 Bezel right
03N6669 Black mouse
07H6826 Blank tailgate plate
07H6827 Blank tailgate plate
10N8994 Blind swap adapter bracket kit
80P6749 Blind swap cassette filler
41V1610 Blower assembly
60H3740 Book planar with VPD
60H3842 Book planar with VPD
60H3852 Book with VPD
15R6976 Bottom filler kit
45D3160 Bracket, media drawer
45D1756 Bridge assembly
04N6923 Brush pad
41V0355 Bulk power controller
11P2344 Cable bracket
41V0453 Chassis
41V1887 Clamp kit
35L0844 Clean cart
46G6844 Cleaning kit
08J5798 Clutch
45D1517 Clutch torque wrench
41V1820 Complete frame tie down kit
41V0943 dc converter
42C2140 Cooling unit power supply
44P2633 Core kit for HMC
44P2450 Corner Bracket
45D0721 Cover

Finding parts, locations, and addresses 181

Table 96. Miscellaneous parts (continued)
CCIN Part number Description
41U0397 Cover, slim
41U0387 Cover kit
41V1676 Cover kit
41V1678 Cover kit
41V1680 Cover kit
41U0386 cover kit, non acoustic
45D1990 Cross member assembly
41V0608 DASD cage
22R2809 DASD filler
42R7992 DASD filler
21P8267 DDR2 DIMM filler
42R4695 DIMM filler
42R4696 DIMM filler
45D1831 DIMM tool
7336677 DIMM tray
31P7513 Display stand
11P3990 Door key
97P6859 Door trim kit
12K0564 Dummy plate
95P4044 DVD assembly
42R7291 DVD filler
95P4093 DVD filler
95P4096 DVD filler
95P4106 DVD latch assembly
46G0334 EMC spring
53P0522 Empty tray
44V3937 ESM assembly
95P4066 Fan assembly
44P0550 Fan cover
15R8923 Filter, door
16R1152 Foam bracket
11P4104 Foam PAD
11P4105 Foam PAD
11P3827 Foam PLATE
12K0566 Frame rail racket
12K0032 Front bezel
45D2202 Front cover
45D2204 Front cover
45D1165 Front cover
41V0593 Front door

182 Finding parts, locations, and addresses

Table 96. Miscellaneous parts (continued)
CCIN Part number Description
41V2355 Front latch
60H3873 FSP controller
45D1708 Gear box
42R5435 GX filler bracket
12R8531 Heat sink
12R8532 Heat sink
99F1718 Heat sink
11P3535 Hinge
11P4106 Hinge
41V0080 Hinge assembly
09N9686 Hinge bracket
46G5947 Ladder
12R9892 Latch
41V1065 Latch bracket
41V1067 Latch bracket
44P2459 Latch bracket
44P0515 Left bracket
39J4471 Left rail
2108930 Lint free cloth
12R8201 Lubricant
11P4747 Magnifier lens
53P0322 Media tray
41V0808 Memory baffle filler
42R7898 Midplane
60H3492 Midplane
40K5342 Monitor T117 enhanced stand
44P4826 Mounting bracket
44V3429 Mounting slide tape
15R9300 Node bar assembly
15R7507 Node filler
41V0809 Node kit
44P1277 Plate cage filler
39J0854 Processor filler
42R8498 Rack mounting fasteners kit
44V4203 RAID controller
45D1859 Rail bottom left
45D1860 Rail bottom right
45D1861 Rail top left
45D1862 Rail top right
45D1121 Rear cover

Finding parts, locations, and addresses 183

Table 96. Miscellaneous parts (continued)
CCIN Part number Description
12R9501 Retainer bracket
41V1799 Retainer bracket
41V1800 Retainer bracket
44V3005 Reusable M3NIF
44P0514 Right bracket
44P0513 Right external bracket
39J4472 Right rail
60G7623 Rivet
5442867 Safety cap
44V4404 SAS controller
44V4413 SAS controller
66F1283 Screw M3
39J3368 Screw M3X6 Torx flat
98F2977 Screw, Torx
39J3889 SCSI differential terminator
12R9042 SCSI repeater card
6422725 Shaft assembly
11P2923 Shipping bar
80P3422 Short BSM kit
16R1508 Side cover
42V2120 Side cover
44H8167 SIMM filler
16R0091 Snap together cassette
31L7174 Soft tie puck
93G1147 Step stool
07H5247 Support rail bracket
2D08 60H4213 System VPD
60H4212 System VPD
40K5341 T115 stand base
45D1715 Table assembly
44P4026 Tailgate bracket
11P1262 Tailgate bracket assembly
35L0967 Test cart
18P8166 Test DISK
53P2519 Test DVD
45E1129 Test tape
41V1913 Tie down
41V1914 Tie down
45D0415 Torque tool
97P2376 Tray assembly

184 Finding parts, locations, and addresses

Table 96. Miscellaneous parts (continued)
CCIN Part number Description
95P4036 Tray assembly
95P4107 Tray latch
07H6655 Velcro tape
51H9502 Velcro tie
45D1677 Weight distribution plate kit
12R8219 Weight distribution plate kit
08J5557 Wheel chock
03N6070 Wrap plug
12R9314 Wrap plug
12R9315 Wrap plug
42R4761 Wrap plug
42R5143 Wrap plug
87H3311 Wrap plug
87H3439 Wrap plug
87H3442 Wrap plug

9125-F2A system parts

Indexed drawings show parts system part numbers.

Finding parts, locations, and addresses 185

Table 97. Final assembly
Index number CCIN Part number Units Description
1 45D1608 2 Bulk power enclosure
2 77G0599 12 Screws
3 74F1823 12 Nut clip
4 45D1139 1 Bulk power supply
5 45D0059 2 Cable bracket
6 77G0599 4 Screw
7 15R7647 AR Bulk power fan
8 45D1133 AR Bulk power regulator
9 45D1595 AR Bulk power controller
10 31L8609 AR Bulk power distribution air flow baffle
11 45D0318 Bulk power fan cover, front only
12 See Node assembly
13 45D1419 1 Right slide rail
14 54G2882 4 Screw
15 45D0802 1 Left slide rail
16 54G2882 4 Screw
17 ESD bracket
18 77G0599 Screw

186 Finding parts, locations, and addresses

Table 98. Modular water units (WMU) assembly
Index number CCIN Part number Units Description
19 45D1094 8 Manifold mount assembly
20 45D1971 1 Shelf
21 77G0599 6 Screw
22 45D2731 2 Modular water unit assembly
23 45D1765 4 Shield
24 45D2732 1 Manifold assembly, left
25 45D2733 1 Manifold assembly, right
26 45D0928 2 Drip cup assembly

Table 99. Node assembly

Index number CCIN Part number Units Description
1 45D1593 1 Power supply
2 87H3621 8 MG DIMM
3 45D0888 116 Node assembly cold air
3 45D3659 114 Node assembly water cooled
4 44V4370 1 Fan assembly, air
4 44V4370 1 Fan assembly, water

Finding parts, locations, and addresses 187

Table 100. Bulk power assembly
Index number CCIN Part number Units Description
5 45D4597 1 I/O assembly without PCI capability
5 45D4595 1 I/O assembly with PCI and I/O Drawer
Attachment Capability
6 45D0965 1 PCI riser, L
7 45D0667 14 PCI filler, short
8 45D0668 14 PCI filler, long
9 45D0666 12 GX filler
10 45D3396 Adapter
11 10N9779 1 VPD
12 45D0971 1 PCI riser,, R
13 45D3396 Adapter

Table 101. Cables

CCIN Part number Description
CCIN Part number Description
44V4147 1 meter SAS cable
44V4148 3 meter SAS cable
44V4149 6 meter SAS cable
44V4158 3 meter SAS cable
44V4159 6 meter SAS cable
44V4160 15 meter SAS cable
15R8392 2 meter hub to node cable

188 Finding parts, locations, and addresses

Table 101. Cables (continued)
CCIN Part number Description
15R8393 3 meter hub to node cable
15R8394 4 meter hub to node cable
15R8385 BPC cable
45D2408 Super UPIC cable

Table 102. Miscellaneous parts

CCIN Part number Description
External cables See Site and hardware planning.
and cords
Cable See Enclosures and expansion units.
configuration
PCI adapters See Managing PCI adapters.
Removable See Managing devices.
media
0524519 Cable tie
08J5557 Wheel chock
11P3662 DASD filler (feature 5798)
44P4573 Front cover (feature 5798)
45D1398 IB planer (feature 5798)
41V2069 DCA (feature 5798)
42V2129 .6 meter 12X IB cable (feature 5798)
42V2131 2.5 meter 12X IB cable (feature 5798)
11P3990 Door key
11P4606 Cable CLP
16R0091 Cassette
42R5435 GX FIL BKT
44P2630 Frame tool
44V4203 RAID controller
44V4404 SAS controller
45D1603 Weight distribution kit
45D1831 DIMM tool
52G4233 SCSI cable
73H2508 Wrap plug
87H3311 Wrap plug
87H3439 Wrap plug
87H3442 Wrap plug
93H5270 Wrap plug
15R7536 Wrap plug
12R9314 Wrap plug
12R9315 Wrap plug
03N6070 Wrap plug

Finding parts, locations, and addresses 189

Table 102. Miscellaneous parts (continued)
CCIN Part number Description
42R4761 Wrap plug
42R5143 Wrap plug
33F8985 Wrap 25 pin connection
93G1147 Step stool
45D2044 Node tool
45D2045 DCA lift tool
45D2046 Power lift tool
45D2052 Hose assembly
45D2053 Hose assembly
45D2054 Hose assembly
45D2055 Hose assembly
45D2056 Hose assembly
45D2057 Hose assembly
45D2058 Hose assembly
45D2059 Hose assembly
45D2060 Hose assembly
45D2104 Tool shelf
45D2124 Outside EU kit
45D2129 Within EU kit
45D2204 Front cover
45D2218 Hose assembly
45D2278 Right rail assembly
45D2279 Left rail assembly
45D2288 Tailgate clamp
45D2725 DCA tool
45D2436 DCA tool
45D2727 MWU support bracket
45D2785 MWU air blocker
45D2964 Fill and drain tool power supply
45D1113 Fill and drain tool
16G8095 Battery

0595, 5095, and 7311-D20 system parts

Indexed drawings show parts system part numbers.

190 Finding parts, locations, and addresses

0595 and 7311-D20 I/O backplane and cabling assembly

Table 103. 0595 and 7311-D20 I/O backplane and cabling assembly part numbers
Index number CCIN Part number Units Description
1 53P0416* 1 DASD cable
2 53P4065* 1 Blower cable
3 53P0414* 1 Control panel cable
4 39J1173* 1 Chassis assembly
53P0220**
5 44H7366* 5 Mounting screw, stiffener
*
6 39J0515 1 I/O backplane
53P3472**

*
Designed to comply with RoHS requirement
**
Not designed to comply with RoHS requirement

Finding parts, locations, and addresses 191

PCI adapters assembly

Table 104. 0595 and 7311-D20 PCI adapters assembly part numbers
Index number CCIN Part number Units Description
1 See Managing 7 (maximum PCI adapter
PCI adapters. quantity)
2 39J1118* 1 Power supply bulkhead
53P0248**
3 44H7366* 4 Screw, power bulkhead mounting
4 44H7366* 3 Screw, PCI plate mounting
5 39J1119* 1 PCI adapter headstock bracket
6 53P2728* 5 PCI dividers
*
7 53P2729 2 PCI dividers

*
Designed to comply with RoHS requirement
**
Not designed to comply with RoHS requirement

192 Finding parts, locations, and addresses

Power, RIO/HSL adapter, and cabling assembly

Table 105. 0595 and 7311-D20 power, RIO/HSL adapter, and cabling assembly part numbers
Index number CCIN Part number Units Description
*
1 39J2781 2 (maximum Power supply
53P4832** quantity)
39J0527* 1 bus adapter RIO/HSL card (bus adapter with
2 2887
97P2670** two external ports)
2 39J0523* 1 -2 bus adapter RIO/HSL-2 card
28E7
97P2459**
3 39J1170* 3 Cable bracket, SCSI
4 44H7366* 1 Screw, SCSI cable
*
5 39J3287 5 RIO/HSL-2 cable bracket
53P0639**
6 44H736* 2 Screw, RIO/HSL-2 cable bracket
*
7 53P0417 Configuration SCSI bus cable
dependent
8 53P0418* Configuration SCSI bus cable
53P0418** dependent
9 39J1175* 1 Power supply filler
53P0233**

*
Designed to comply with RoHS requirement
**
Not designed to comply with RoHS requirement

Finding parts, locations, and addresses 193

Operator panel assembly

Table 106. 0595 and 7311-D20 operator panel assembly part numbers
Index number CCIN Part number Units Description
*
1 39J1695 2 Disk drive backplane (disk drive enclosure
97P3138** included)
2 39J3284* 4 Screw, disk-drive-backplane mounting
*
3 250D 39J3087 1 Operator panel
53P2535**
4 39J1178* 1 Processor cover
53P0275**
5 44H736* 4 Screw, cover-mounting

*
Designed to comply with RoHS requirement
**
Not designed to comply with RoHS requirement

194 Finding parts, locations, and addresses

Fans and disk drives assembly

Table 107. 0595 and 7311-D20 fans and disk drives assembly part numbers
Index number CCIN Part number Units Description
*
1 39J1176 4 Fan assembly
53P0262**
2 39J3383* 1 Disk-drive enclosure 12 pack (disk drive
53P0250** backplanes included)
3 39J3283* 8 Screw, disk drive enclosure mounting
4 03N5270* 300 GB Ultra320 10K rpm 80 pin SCSI disk
80P3157** drive/carrier
03N6335*
80P3400**
4 80P3161** 36.4 GB 15K RPM Ultra3 SCSI disk
00P2697** drive/carrier
4 09P3928** 73.4 GB 10K RPM, 80-pin SCSI disk
09P4890** drive/carrier
4 00P3829** 18.2 GB 10K RPM SCSI disk drive/carrier
00P3064** Note: The FRU part numbers are
interchangeable. Order the FRU part number
that matches the FRU part number you are
replacing.

Finding parts, locations, and addresses 195

Table 107. 0595 and 7311-D20 fans and disk drives assembly part numbers (continued)
Index number CCIN Part number Units Description
**
4 00P3831 36.4 GB 10K RPM SCSI disk drive/carrier
00P3068** Note: The FRU part numbers are
interchangeable. Order the FRU part number
that matches the FRU part number you are
replacing.
4 05J7982* Front spring for 36.4 GB 10K RPM ultra320
SCSI disk drive assembly
5 44H736* 4 Screw, filler-plate mounting
*
6 44H736 1 (optional) Disk drive filler plate
*
7 42R5254 1 Left rail
53P3451**
8 42R5255* 1 Right rail
53P3452**

*
Designed to comply with RoHS requirement
**
Not designed to comply with RoHS requirement

Covers and brackets assembly

Table 108. 0595 and 7311-D20 cover and bracket assembly part numbers
Index number CCIN Part number Units Description
*
1 0595: 39J3326 1 Front cover
53P1457** and
7311-D20:
39J4661
2 44H736* 2 Screw, latch bracket
*
3 53P2572 1 Latch bracket assembly left
*
4 42R4299 4 Cable arm bracket
53P6019**
5 44H736* 1 Screw, cable arm bracket
*
6 53P2573 1 Latch bracket assembly right

196 Finding parts, locations, and addresses

*
Designed to comply with RoHS requirement
**
Not designed to comply with RoHS requirement

Cover assembly for 5095

Finding parts, locations, and addresses 197

Table 109. Cover assembly part numbers for 5095
Index CCIN Part number Units Description
*
1 39J3084 1 Display panel tray assembly
53P0330**
2 NONUM 1 Display panel enclosure assembly
3 53P0320 5 Screw
*
4 53P0308 1 Cover, display panel
5 53P0280 1 Cover, top
6 53P0320 2 Screw
*
7 53P0285 1 Cover, left side
8 53P0320 2 Screw
*
9 53P0303 1 Cover assembly, back
*
10 39J1179 1 Cover assembly, right side
53P0286**
11 53P0320 2 Screw
12 (order part listed in index 1 EMC bracket
10)
13 06P5858 (order part listed 1 Latch housing
in index 10)
14 03K9553* (order part 2 Screw, M3.5 x 7
listed in index 10)
15 06P5857 (order part listed 1 Latch handle
in index 10)
16 NONUM 1 Bracket, DASD filler
17 NONUM 4 Screw
*
18 39J3317 1 Cover assembly, front
53P1359**

*
Designed to comply with RoHS requirement
**
Not designed to comply with RoHS requirement
Table 110. Cables
CCIN Description Part number
Operator panel cable 42R4054*
SCSI bus 0 cable 42R4057*
SCSI bus 1 cable 42R4058*
3000 MM GX Dual-port 4x HCA cable 42R6244*
8000 MM GX Dual-port 4x HCA cable 42R6245*
1500 MM GX Dual-port 4x HCA cable 42R6243*
Y cable 52G0173*
ASM differential SCSI-2 cable 52G4291**
ASM differential SCSI-2 cable 52G4233**
SCSI-4 drop table 42R4756*
1 meter RIO G cable 39J2562*
3.5 meter RIO G cable 39J2554*

198 Finding parts, locations, and addresses

Table 110. Cables (continued)
CCIN Description Part number
10 meter RIO G cable 39J2561*
3.7 meter serial cable 10N7158*
2 meter SPCN cable 22R5217*
3 meter SPCN cable 22R5239*
15 meter SPCN cable 22R5221*
6 meter SPCN cable 22R5219*

*
Designed to comply with RoHS requirement
**
Not designed to comply with RoHS requirement
Table 111. Miscellaneous parts
CCIN Description Part number
External cables See Site and hardware
planning.
Removable media See Managing devices.
PCI adapters See Managing PCI
adapters.
Cable configuration See Enclosures and
expansion units.
Bezel filler 97P4179*
53P6213**
Wrap plug 12R9315*
12R6249**
Wrap plug 42R4761*
6298964**
Scurry card bracket 80P7033**
Plug 232 10N6539*
Wrap, 15 pin 34F0876*
Wrap connector 33F8985*
Wrap plug 43G0928*
Wrap plug 73H2508**
Wrap plug 87H3442**
Wrap plug 87H3588**
Wrap plug 40F9904**
128 MB DRAM option card 34L5388**
Bracket 12R6965*
Remote asynchronous node (rack). 09P4096**
Differential SCSI adapter 11K0671**
Front cover 39J4661*
53P2020**
PCI cover 39J1177*
53P0268**
Bracket 00P4885**

Finding parts, locations, and addresses 199

Table 111. Miscellaneous parts (continued)
CCIN Description Part number
Front cover 53P1355**
V.35 wrap 71F0163**
Fiber-Distributed Data Interface (FDDI) adapter 73H3401**
Hot plug kit 44P0322**
Wrap plug 04H7648**
Battery pack 44L0305**
Bracket 44P3912**
PCI slot filler 80P2341**

*
Designed to comply with RoHS requirement
**
Not designed to comply with RoHS requirement

5094, 5294, 5096, and 5296 system parts

Indexed drawings show parts system part numbers.

The 5294 is comprised of two 5094 units, and the 5296 is comprised of two 5096 units

Note: The parts are applicable for every system, except where the machine type model is listed.

200 Finding parts, locations, and addresses

Cover assembly

Table 112. Cover assembly part numbers

Index CCIN Part number Units Description
*
1 39J4314 1 Top cover
24L0825**
2 1621811* 4 Screw, M4 (10 mm)
*
3 42R4064 1 Back cover
**
24L1071 1 Hinge pin, top

Finding parts, locations, and addresses 201

Table 112. Cover assembly part numbers (continued)
Index CCIN Part number Units Description
*
4 39J4313 1 Side cover
24L0824**
5 1621811* 12 Screw, M4 (10 mm)
**
6 24L1078 1 Front filler cover
*
7 1621811 2 Screw, M4 (10 mm)
*
8 42R4039 1 Front cover
**
24L1071 Hinge pin, top

*
Designed to comply with RoHS requirement
**
Not designed to comply with RoHS requirement

202 Finding parts, locations, and addresses

Final assembly

Table 113. Final assembly part numbers

Index CCIN Part number Units Description
*
1 247B 39J4611 1 Display panel
24L0962**
2 42R4037* AR Filler (removable media)
44H8406**
3 See Managing devices. AR Removable media.
*
4 42R4045 AR Disk unit EMC access plate
24L0821** for 5094
42R7229* for 5096

*
Designed to comply with RoHS requirement
**
Not designed to comply with RoHS requirement

Finding parts, locations, and addresses 203

Table 114. Final assembly part numbers
Index CCIN Part number Units Description
5 NONUM 1 Removable media enclosure assembly
*
6 1621811 2 Screw, M4 (10 mm)

204 Finding parts, locations, and addresses

Table 114. Final assembly part numbers (continued)
Index CCIN Part number Units Description
*
7 1621817 2 Screw
*
8 39J5598 1 Center support bracket
24L1067**
9 1621811* 2 Screw, M4 (10 mm)
10 NONUM AR Five disk unit enclosure assembly
*
11 1621811 12 Screw, M4 (10 mm)
*
12 1621817 6 Screw
**
13 6714 44L0063 5094 AR Disk unit assembly
**
13 6717 53P5970 5094 Disk unit assembly
**
13 44H4637 5094 Disk unit assembly
**
13 6718 53P5971 5094 18 GB unit assembly
**
13 6719 53P5972 5094 36 GB unit assembly

*
Designed to comply with RoHS requirement
**
Not designed to comply with RoHS requirement

Finding parts, locations, and addresses 205

Table 115. Final assembly part numbers
Index CCIN Part number Units Description
14 NONUM 1 Shelf, base disk unit
*
15 1621811 3 Screw, M4 (10 mm)
*
16 28CB 42R3859 1 Base disk unit board/stiffener assembly
53P4001** for 5094
42R7006* for 5096
17 42R7218* AR Disk unit board/stiffener assembly
*
18 1621838 1 Screw

206 Finding parts, locations, and addresses

Table 115. Final assembly part numbers (continued)
Index CCIN Part number Units Description
19 NONUM AR Shelf, disk unit
*
20 1621811 2 Screw, M4 (10 mm)

*
Designed to comply with RoHS requirement
**
Not designed to comply with RoHS requirement

Finding parts, locations, and addresses 207

Table 116. Final assembly part numbers
Index CCIN Part number Units Description
*
21 42R7229 1 EMC access plate
22 NONUM 1 Air-moving device (fan) door assembly
*
23 1621811 2 Screw, M4 (10 mm)
*
24 39J5235 2 Air-moving device (fan)
04N3345**
25 39J3082* 1 Power board/stiffener assembly
21P3793**
26 1621816* 6 Screw
27 1 Time of day (TOD) battery
*
28 28B7 39J3058 1 I/O backplane
53P6023**

*
Designed to comply with RoHS requirement
**
Not designed to comply with RoHS requirement

Final assembly

208 Finding parts, locations, and addresses

Table 117. Final assembly part numbers
Index CCIN Part number Units Description
*
30 42R4295 1 Power subframe assembly for dual line cord
53P5259**
31 1621811* 8 Screw, M4 (10 mm)
*
32 39J5845 2 Filler, spacer
24L0940**
33 1621811* 2 Screw, M4 (10 mm)
*
34 39J5844 2 Filler, power supply
*
35 1621811 4 Screw, M4 (10 mm)
*
36 39J5171 2 AC power distribution assembly
53P5263**
37 1621811* 4 Screw, M4 (10 mm)
*
38 39J5273 4 Power supply assembly, 840 W
53P1038**

`* Designed to comply with RoHS requirement

**
Not designed to comply with RoHS requirement

Finding parts, locations, and addresses 209

Optional hardware assembly for 5294 and 5296 expansion units

Table 118. Optional hardware assembly part numbers for 5294 and 5296 expansion units
Index Part number Units Description
**
1 00P2200 1 Type 6 power distribution unit single phase U.S.
**
00P2201 1 Type 6 power distribution unit two phase
**
00P2202 1 Type 6 power distribution unit three phase
**
09P2891 1 Type 6 power distribution unit single phase World
Trade
00P3663** 1 Type 7 Power distribution panel (1 Phase)
**
97P3574 1 Type 7 Power distribution panel (1 Phase World
Trade)
97P3575** 1 Type 7 Power distribution panel (3 Phase World
Trade)

210 Finding parts, locations, and addresses

Table 118. Optional hardware assembly part numbers for 5294 and 5296 expansion units (continued)
Index Part number Units Description
*
2 74F1823 4 Nut clip
0375867**
3 1624779* 4 Screw
6200684**
5 1624779* 16 Screw
6200684**

*
Designed to comply with RoHS requirement
**

Not designed to comply with RoHS requirement

Table 119. Miscellaneous parts
CCIN Description Part number
External cables and cords See Site and hardware
planning.
Removable media See Managing devices.
PCI adapters See Managing PCI
adapters.
Cable configuration See Enclosures and
expansion units.
Signal cable 42R4116*
97H7474**
Operator panel cable 24L1752**
Operator panel cable 04N6113*
97H7473**
Fan cable 42R4035*
97H7475**
SPCN cable 42R4047*
97H7544**
SCSI cable 42R4049*
53P5651**
SCSI cable 42R4034*
53P5649**
SCSI cable 42R4050*
53P5650**
2691 HSL I/O bridge 04N6907**
DASD cage 39J4304*
24L0761**
Full length airflow filler 46G3556**
Battery pack 97H7318**
DASD expansion shelf, plate 39J5597*
Cable assembly 24L0843*
97H7607**

*
Designed to comply with RoHS requirement
**
Not designed to comply with RoHS requirement

Finding parts, locations, and addresses 211

5786, 5787, 7031-D24, and 7031-T24 system parts
Indexed drawings show parts system part numbers.

Note:
v For external cable FRU part number and description for your I/O enclosure, see the Site and hardware
planning, order number SA76-0091.
v For procedures on cabling your I/O enclosure, see Customer-Installable Features for the IBM p 570
(9117-MMA), order number SA76-0104. and go the topic "Connecting the 5786, 5787, 7031-D24 or
7031-T24 SCSI disk drive enclosure".
v Throughout this topic, the abbreviation RoHS is used. RoHS refers to European Union Directive
2002/95/EC on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic
Equipment Site and hardware planning All part numbers are suitable for the 7031-T24, 7031-D24, 5786,
and 5787 unless otherwise indicated.

Cover assemblies

Table 120. Stand-alone cover assembly part numbers for 5787 and 7031-T24
Index CCIN Part number Units per Description
number assembly
1 12R8505* 1 Front cover assembly stand-alone
*
2 12R8373 1 Side cover assembly stand-alone, left

212 Finding parts, locations, and addresses

Table 120. Stand-alone cover assembly part numbers for 5787 and 7031-T24 (continued)
Index CCIN Part number Units per Description
number assembly
3 12R8376* 1 Side cover assembly stand-alone, right
*
4 12R8379 1 Footstand assembly stand-alone
*
5 1624741 4 Screw, M3 x 4 pan head

*
Designed to comply with RoHS requirement
**
Not designed to comply with RoHS requirement

Table 121. I/O enclosure assembly (front view)

Index CCIN Part number Units per Description
number assembly
1 41U0299* 1 Rack configured chassis assembly (includes
chassis, disk drive backplane, VPD card).
Removal and replacement procedures are sent
with the FRU.
1 41U0301* 1 Stand-alone configured chassis assembly
(includes chassis, disk drive backplane, VPD
card). Removal and replacement procedures are
sent with the FRU.
2 39J2051* 1 Mount Rail assembly (7031-D24 only)
*
2 97P4178 DASD bezel (not shown)
3P5556**
2 97P4179* DASD filler panel (not shown)
53P6213**
3 03N5260* 1-12 per side 73.4 GB Disk drive with U320 carrier, 10K RPM,
00P3833** 80 pin

Finding parts, locations, and addresses 213

Table 121. I/O enclosure assembly (front view) (continued)
Index CCIN Part number Units per Description
number assembly
3 03N6325* 1-12 per side 73.4 GB Disk drive with U320 carrier, 10K RPM,
00P3072** 80 pin
3 03N5265* 1-12 per side 146.8 GB Disk drive with U320 carrier, 10K RPM,
00P3835** 80 pin
3 03N6330* 1-12 per side 146.8 GB Disk drive with U320 carrier, 10K RPM,
00P2665** 80 pin
3 03N5270* 1-12 per side 300 GB Disk drive with U320 carrier, 10K RPM,
80P3157** 80 pin
3 03N6335* 1-12 per side 300 GB Disk drive with U320 carrier, 10K RPM,
80P3400** 80 pin
3 03N5275* 1-12 per side 36.4 GB Disk drive with U320 carrier, 15K RPM,
80P3159** 80 pin
3 03N6340* 1-12 per side 36.4 GB Disk drive with U320 carrier, 15K RPM,
00P2693** 80 pin
3 03N5280* 1-12 per side 73.4 GB Disk drive with U320 carrier, 15K RPM,
80P3163** 80 pin
3 03N6345* 1-12 per side 73.4 GB Disk drive with U320 carrier, 15K RPM,
00P2685** 80 pin
3 03N5285* 1-12 per side 3.5 inch 146 GB SCSI DASD, 15 K RPM
80P3911**
3 10N8578* 1-12 per side 300 GB Disk drive with U320 carrier, 15K RPM,
80 pin
3 03N5270* 300 GB Ultra320 10K rpm 80 pin SCSI disk
80P3157** drive/carrier
3 4326 39J3695 1-12 per side 3.5 inch 35 GB SCSI disk drive, 15K RPM (IBM i)
3 4327 39J3696 1-12 per side 3.5 inch 70 GB SCSI disk drive, 15K RPM (IBM i)
3 4328 39J3697 1-12 per side 3.5 inch 141 GB SCSI disk drive, 15K RPM (IBM
i)
3 4329 42R6676 1-12 per side 3.5 inch 282 GB SCSI disk drive, 15K RPM (IBM
i)
4 15R6792* 3 Fan assembly
12R9950*
5 41U0264* 1 Front bezel (Rack unit only)
*
6 39J2051 1 Mount Rail assembly (See index number 2 in this
table)
7 12R8511* 3 Chassis handle
90H9196*

*
Designed to comply with RoHS requirement
**
Not designed to comply with RoHS requirement

214 Finding parts, locations, and addresses

Table 122. I/O enclosure assembly (back view)
Index CCIN Part number Units per Description
number assembly
1 Chassis assembly (refer to table 2 for part
number)
2 Disk drive assemblies (refer to table 2 for part
number)
3 506E 12R9042* 1-4 SCSI repeater card assembly single
12R7477*
3 506D 12R9040* 1-4 SCSI repeater card assembly dual
12R7475*
3 12R7457* 1-3 SCSI repeater card filler assembly (not shown)
**
4 12R9078 1-2 966 W power supply
Note: Use with a power supply that has the
same wattage.
4 15R7998* 1-2 845 W power supply
Note: Use with a power supply that has the
same wattage.
4 12R7454* 1 Power supply filler assembly (not shown)
*
5 12R6121 1 Left chassis bracket
*
6 12R6122 1 Right chassis bracket

*
Designed to comply with RoHS requirement
**
Not designed to comply with RoHS requirement

Finding parts, locations, and addresses 215

5790 and 7311-D11 system parts
Indexed drawings show parts system part numbers.

All part numbers are suitable for both the 5790 and 7311-D11 unless otherwise indicated.

Final assembly

Table 123. Final assembly part numbers

Index number CCIN Part number Units Description
1 22R3958* 2 228 W Power supply
22R5494**
2 See Plug and 2 Cable, power
receptacle
types: Model
7311-D10,
7311-D11, 5790.
3 09P3185** 5 Guide, power cable
*
4 80P2654 1 Cover, power cable channel
**
5 80X2646 1 Access cover
**
6 1624743 2 Screw, access cover

*
Designed to comply with RoHS requirement
**
Not designed to comply with RoHS requirement

216 Finding parts, locations, and addresses

Table 124. Final assembly, continued
Index number CCIN Part number Units Description
*
7 32N1256 1 Fan assembly
03N6069**
8 80X2646** 1 Bracket, bulkhead
**
9 1621829 2 Screw, bulkhead bracket
*
10 03N6196 1 Cable, fan
09P5417**
11 80X2646** 1 Tray, power cable
**
12 1621829 2 Screw, tray mounting
**
13 80X2646 2 Guide, upper
**
14 1621829 4 Screw, upper guide mounting
15 NONUM SPCN connector card (included with index
number 19)
16 NONUM Screw (included with index number 19)
**
17 80X2646 2 Guide, lower
**
18 1624749 8 Screw, lower guide mounting
*
19 23R0181 1 I/O backplane assembly (includes SPCN
22R6222** connector card)
19 80P6626** I/O drawer backplane
**
20 1624743 6 Screw, backplane mounting

Finding parts, locations, and addresses 217

*
Designed to comply with RoHS requirement
**
Not designed to comply with RoHS requirement

Table 125. Final assembly, continued

Index number CCIN Part number Units Description
21 03N6541 2 Filler, EMC
22 See Managing AR PCI cassette
PCI adapters.
23 28FF 03N5633* 1 RIO/HSL card
80P6006**

*
Designed to comply with RoHS requirement
**
Not designed to comply with RoHS requirement

218 Finding parts, locations, and addresses

Rack-mounting enclosure

Table 126. Rack-mounting enclosure

Index number CCIN Part number Units Description
*
24 93H4729 2 Screw, chassis
*
25 80P2665 2 Cable support bracket
*
26 00G1268 2 Screw, bracket mounting
40F9987**
27 NONUM 2 I/O subsystem retention bracket
*
28 1624779 4 Screw, I/O subsystem mounting
6200684**
29 1621829** 2 Screw
*
30 39J4472 1 Right rail
03N3847**
31 1624779* 4 Screw, rail mounting
6200684**
32 74F1823* 12 Nut clip, rail mounting
0375867**
33 NONUM 1 Chassis
*
34 1624779 4 Screw, rail mounting
6200684**
35 80P5233* 1 Front cover
09P4778**
36 04N6587* 2 Thumbscrew, shipping
*
37 39J4471 1 Left rail
03N3845**
38 80P2664* 1 Back filler for empty I/O subsystem space

Finding parts, locations, and addresses 219

Table 126. Rack-mounting enclosure (continued)
Index number CCIN Part number Units Description
*
39 93H4729 2 Screw, filler mounting

*
Designed to comply with RoHS requirement
**
Not designed to comply with RoHS requirement
Table 127. Cables
CCIN Description Part number
3000 MM GX Dual-port 4x HCA cable 42R6244*
8000 MM GX Dual-port 4x HCA cable 42R6245*
1500 MM GX Dual-port 4x HCA cable 42R6243*
Y cable 52G0173**
SCSI2 cable 52G4291**
SCSI cable 52G4233**
3.7 M serial cable 10N7158*
8 M serial cable 10N7159*
1 M I/O cable 39J2562*
3. 5 M I/O cable 39J2554*
2 M SPCN cable 22R5217*
3 M SPCN cable 22R5239*
15 M SPCN cable 22R5221*
6 M SPCN cable 22R5219*
15 feet cable 43G0937**
9 inch cable 43G0936**
SCSI cable 42R4756*

*
Designed to comply with RoHS requirement
**
Not designed to comply with RoHS requirement
Table 128. Miscellaneous parts
CCIN Description Part number
External cables and cords See Site and hardware
planning.
Removable media See Managing devices.
PCI adapters See Managing PCI
adapters.
Cable configuration See Enclosures and
expansion units.
Cassette filler 80P6749*
80P5354**
Wrap plug 12R9315*
12R6249**
Wrap plug 42R4761*
6298964**

220 Finding parts, locations, and addresses

Table 128. Miscellaneous parts (continued)
CCIN Description Part number
Scurry card bracket 80P7033**
Interposer 4=1 43G0935*
51G8610**
Plug 232 10N6539*
Wrap connector 33F8985**
Wrap plug 10N6541*
Wrap plug 43G0928*
Wrap plug 73H2508**
Wrap plug 87H3442**
Wrap plug 87H3588**
Wrap plug 40F9904**
128 MB DRAM option card 34L5388*
Universal 4 port 10/100 ethernet adapter 80P3553*
Bracket 00P2402**
Bracket 09P4911**
Bracket 12R6965*
Bracket 41V0606*
Remote asynchronous node (rack). 09P4096**
Filler plate 09P4912**
Differential SCSI adapter 11K0671**
Mechanical assembly 09P3118**
Bracket 09P2853**
V.35 wrap 71F0163**
FRU FDDI DAS 73H3401**
Hot plug kit 44P0322**
Right rail 21P7876**
Wrap plug 04H7648**
Bracket 00P2753**
Blind swap assembly 97P6654**
32 MB fast-write cache option card 44L0305**
Bracket 44P3912*
44P2650**
Blind swap guide, upper 00P2750**
Bracket 09P2753**
Drawer assembly 09P4746**
Left rail assembly 21P7875**
Cover assembly 00P2788**
Filler,10 Gbps, Ethernet IOA (long) 80P2341**
Bracket, bulkhead 00P2752**
Half-drawer mechanical assembly 00P2751**

Finding parts, locations, and addresses 221

*
Designed to comply with RoHS requirement
**
Not designed to comply with RoHS requirement

5791, 5794, 5797, and 5798 system parts

Indexed drawings show parts system part numbers.

Final assembly

Table 129. Final assembly (front) part numbers

Index number Part number Units per Description
assembly
1 41V0453 1 Chassis
2 45D2252 4 Fan assembly (features 5794, 5797, and 5798)
2 45D2252 4 Fan assembly (feature 5791)
3 44P1277 2 Disk drive enclosure filler (feature 5794)
4 11P3662 AR Disk drive filler
5 44P4573 1 Front cover
6 See Disk drives AR Disk drive
7 41V0608 AR Disk unit enclosure and backplane assembly
41V1064 Screw
11P3457 Screw (feature 5794)
8 41V0943 2 Power supply (5DCA-BCS) (features 5791, 5794)
8 41V2069 2 Power supply (features 5797, 5798)

222 Finding parts, locations, and addresses

Back view

Table 130. Final assembly (back) part numbers

Index number Part number Units per Description
assembly
1 41V0453 1 Chassis
2 NONUM AR GX riser card, part of the I/O backplane (see index
number 4)
3 16R0091 AR PCI adapter cassette assembly
4 45D2064 2 I/O backplane (feature 5798)
4 45D2068 2 I/O backplane (feature 5797)
4 41V1231 2 I/O backplane (features 5791, 5794)

Table 131. Miscellaneous parts

CCIN Part number Description
See Managing PCI adapters
PCI adapters.
44P2629 Tool
7H5247 Bracket (features 5791, 5797, and 5798)
11P2344 Cable bracket
1695244 Screw m4 (features 5791, 5797, and 5798)
08L0358 Screw (feature 5797)
54G2882 Screw
74F1823 Nut
80P6749 BS filler
80F7499 Torx screw (feature 5797)
44P0182 DASD tool (features 5797, and 5798)
44P0549 Tool insert (features 5797, and 5798)

Finding parts, locations, and addresses 223

5796 and 7314-G30 system parts
Indexed drawings show parts system part numbers.

Cover assemblies

Table 132. Cover assembly part numbers

Index CCIN Part number Units per Description
number assembly
1 04N6587 1 Screw
2 80P5960 2 Front bezel
3 80P5955 1 Service label
4 39J5190 1 Rail assembly
5 39J5190 1 Rail assembly
6 80P6903 1 Air flow block

224 Finding parts, locations, and addresses

Table 133. Assembly
Index CCIN Part number Units per Description
number assembly
7 44V4294 2 300 W power supply
8 80P5880 1 Chassis assembly, includes power cables
9 42R4007 1 PCI adapter cassette, Gen 3 single wide (handle
at bottom), long
9 42R4008 1 PCI adapter cassette, Gen 3 double wide (handle
at bottom), long
10 10N7690 2 EMC shield assembly

Finding parts, locations, and addresses 225

Table 134. Final assembly part numbers
Index CCIN Part number Units per Description
number assembly
11 10N8782 1 GX card with hardware, RIO 12X long range
11 10N7774 1 GX card with hardware, RIO 12X short range
12 07P6949 1 Fabrication assembly
13 80P5940 1 Strain relief assembly (green), RIO 12X long
range
13 03N5871 1 Strain relief assembly (olive), RIO 12X short
range
14 520D 46K6826 1 SPCN card with hardware
15 03N5660 4 Hold down bracket
16 53P0320 4 Screw

Table 135. Cable parts

CCIN Description Part number
2.5 meter RIO, short range 42V2131
3 meter RIO, short range 42V2132
3.5 meter RIO, short range 42V2133
1500 MM RIO 12X, long range 42R6153
2500 MM RIO 12X, long range 42R6154
4000 MM RIO 12X, long range 42R6155
6000 MM RIO 12X, long range 42R6156

226 Finding parts, locations, and addresses

Table 135. Cable parts (continued)
CCIN Description Part number
8000 MM RIO 12X, long range 42R6157
10000 MM RIO 12X, long range 42R6158
6000 MM RIO 12X, long range 42R6159
8000 MM RIO 12X, long range 42R6160
Y cable 40H6603
SCSI-3 cable 52G4233
SCSI-4 cable 42R4756

Table 136. Miscellaneous parts

CCIN Description Part number
External cables and cords See Site and hardware
planning.
PCI adapters See Managing PCI
adapters.
Cable configuration See Enclosures and
expansion units.
PCI filler bracket 39J0260
Wrap plug 87H3439
Wrap plug 87H3442
Wrap plug 87H3311
Wrap plug 73H2508
Wrap plug 93H5270

5802 and 5877 system parts

Indexed drawings show parts system part numbers.

Finding parts, locations, and addresses 227

Front assembly

Table 137. Front assembly part numbers

Index CCIN Part number Units per Description
number assembly
1 1 Chassis assembly
2 45D5215 1 Disk unit cage assembly (5802 only)
2 44V7924 1 Disk unit cage filler (5877 only)
3 58B0 44V6821 0 - 18 69 GB small form factor Solid-state drive (5802
only)
3 198B 44V4429 0 - 18 69.7 GB 15K small form factor SAS disk drive
(5802 only)
3 198C 44V6844 0 - 18 139.5 GB 15K small form factor SAS disk drive
(5802 only)
3 42R8391 0 - 18 73.4 GB 10K small form factor SAS disk drive
(5802 only)
3 44V4426 0 - 18 73.4 GB 15K small form factor SAS disk drive
(5802 only)
3 42R8392 0 - 18 146.8 GB 10K small form factor SAS disk drive
(5802 only)
3 44V6845 0 - 18 146.8 GB 15K small form factor SAS disk drive
(5802 only)
3 44V6833 0 - 18 300 GB 10K small form factor SAS disk drive
(5802 only)
4 26K8680 0 - 18 Disk unit filler (5802 only)
5 45D6918 4 Port card assembly
6 42R8429 4 Fan assembly
7 44V6774 2 Power supply

228 Finding parts, locations, and addresses

Back assembly

Table 138. Back assembly part numbers

Index CCIN Part number Units per Description
number assembly
8 45D5321 1 PCI cage multicard assembly
9 Comes with PCI cage multicard assembly and is
not a separate FRU
10 45D5229 1 EMC card assembly
11 44V5743 1 EMC filler bracket
12 44V5739 1 Power cable assembly
13 45D5008 1 SAS conduit card assembly (5802 only)
13 44V7286 1 SAS conduit card filler (5877 only)
14 45D5221 1 Midplane assembly

Table 139. Cables

CCIN Description Part number
0.6 meter SAS AT cable (SAS adapter to 5802 SAS conduit card) 44V5132
0.6 meter IB cable 45D4785
1.5 meter IB cable 45D4786
2.5 meter IB cable 45D4787
3 meter IB cable 45D5271
8 meter IB cable 45D4788

Table 140. Miscellaneous parts

CCIN Description Part number
External cables and cords See Site and hardware
planning.

Finding parts, locations, and addresses 229

Table 140. Miscellaneous parts (continued)
CCIN Description Part number
PCI adapters See Managing PCI adapters.
Cable configuration See Enclosures and
expansion units.

5803 and 5873 system parts

Indexed drawings show parts system part numbers.

Front assembly

Table 141. Front assembly part numbers

Index CCIN Part number Units per Description
number assembly
1 44V8265 1 Chassis assembly
2 45D5223 1 Disk unit cage assembly
2 44V5898 1 Disk unit cage filler
3 58B0 44V6821 AR 2.5-inch 69 GB Solid-state drive
3 58B3 74Y5294 AR 2.5-inch 177 GB Solid-state drive
3 AR Disk unit assembly
4 39Y8083 AR Disk unit filler
5 45D6918 4 Port card assembly
6 42R8429 6 Fan assembly
7 45D3978 2 Power supply

230 Finding parts, locations, and addresses

Back assembly

Table 142. Back assembly part numbers

Index CCIN Part number Units per Description
number assembly
8 45D5321 2 PCI cage multicard assembly
9 Not a separate FRU, comes with PCI adapter
10 45D5008 1 SAS conduit card assembly
10 44V7286 1 SAS conduit card filler
11 45D5438 1 Midplane assembly

Table 143. Cables

CCIN Description Part number
.6 meter IB cable 45D4785
1.5 meter IB cable 45D4786
2.5 meter IB cable 45D4787
3 meter IB cable 45D5271
8 meter IB cable 45D4788

Table 144. Miscellaneous parts

CCIN Description Part number
External cables and cords See Site and hardware
planning.
PCI adapters See Managing PCI adapters.
Cable configuration See Enclosures and
expansion units.

Finding parts, locations, and addresses 231

5886 system parts
Indexed drawings show parts system part numbers.

Assembly

Table 145. I/O backplane and cabling assembly part numbers

Index number CCIN Part number Units Description
1 509A 44V3937 2 Enclosure Services Manager (ESM)
2 509C 42C2140 2 Power supply
3 509B 42R7898 1 Midplane
4 39R6584 1 Right bezel
5 58B0 44V6819 112 3.5-inch 69 GB Solid-state drive
5 42R6690 112 69.7 GB SAS 15 K, IBM i
5 42R6691 112 139.5 GB SAS 15 K, IBM i
5 42R6692 112 283.7 GB SAS 15 K, IBM i
5 10N7230 112 73.4 GB SAS 15 K, AIX and Linux
5 10N7232 112 146.8 GB SAS 15 K, AIX and Linux
5 10N7234 112 300 GB SAS 15 K, AIX and Linux
6 39R6583 1 Left bezel

Table 146. Cables

CCIN Part number Description
44V4041 1 meter SAS 4x AI cable
44V4163 3 meter SAS 4x AE cable

232 Finding parts, locations, and addresses

Table 146. Cables (continued)
CCIN Part number Description
44V4164 6 meter SAS 4x AE cable
44V4147 1 meter SAS 4x EE cable
44V4148 3 meter SAS 4x EE cable
44V4149 6 meter SAS 4x EE cable
44V4151 3 meter SAS 2x cable
44V4152 6 meter SAS 2x cable
44V4157 1.5 meter SAS YO cable
44V4158 3 meter SAS YO cable
44V4159 6 meter SAS YO cable
44V4160 15 meter SAS YO cable
44V4161 1.5 meter SAS YI cable
44V4162 3 meter SAS YI cable
44V4154 3 meter SAS X cable
44V4155 6 meter SAS X cable
44V4156 15 meter SAS X cable
42R6748 SAS W cable

Table 147. Miscellaneous parts

CCIN Part number Description
External cables See Site and hardware planning.
and cords
Cable See Enclosures and expansion units.
configuration
42R6748 Wrap plug
39R6548 ESM blank
39M4375 DASD blank
39M5377 Power cord rack jumper
39R6550 Rail kit
22R2809 DASD filler

Finding parts, locations, and addresses 233

234 Finding parts, locations, and addresses
Appendix. Notices
This information was developed for products and services offered in the U.S.A.

The manufacturer may not offer the products, services, or features discussed in this document in other
countries. Consult the manufacturer's representative for information on the products and services
currently available in your area. Any reference to the manufacturer's product, program, or service is not
intended to state or imply that only that product, program, or service may be used. Any functionally
equivalent product, program, or service that does not infringe any intellectual property right of the
manufacturer may be used instead. However, it is the user's responsibility to evaluate and verify the
operation of any product, program, or service.

The manufacturer may have patents or pending patent applications covering subject matter described in
this document. The furnishing of this document does not grant you any license to these patents. You can
send license inquiries, in writing, to the manufacturer.

The following paragraph does not apply to the United Kingdom or any other country where such
provisions are inconsistent with local law: THIS INFORMATION IS PROVIDED AS IS WITHOUT
WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain
transactions, therefore, this statement may not apply to you.

This information could include technical inaccuracies or typographical errors. Changes are periodically
made to the information herein; these changes will be incorporated in new editions of the publication.
The manufacturer may make improvements and/or changes in the product(s) and/or the program(s)
described in this publication at any time without notice.

Any references in this information to Web sites not owned by the manufacturer are provided for
convenience only and do not in any manner serve as an endorsement of those Web sites. The materials at
those Web sites are not part of the materials for this product and use of those Web sites is at your own
risk.

The manufacturer may use or distribute any of the information you supply in any way it believes
appropriate without incurring any obligation to you.

Any performance data contained herein was determined in a controlled environment. Therefore, the
results obtained in other operating environments may vary significantly. Some measurements may have
been made on development-level systems and there is no guarantee that these measurements will be the
same on generally available systems. Furthermore, some measurements may have been estimated through
extrapolation. Actual results may vary. Users of this document should verify the applicable data for their
specific environment.

Information concerning products not produced by this manufacturer was obtained from the suppliers of
those products, their published announcements or other publicly available sources. This manufacturer has
not tested those products and cannot confirm the accuracy of performance, compatibility or any other
claims related to products not produced by this manufacturer. Questions on the capabilities of products
not produced by this manufacturer should be addressed to the suppliers of those products.

All statements regarding the manufacturer's future direction or intent are subject to change or withdrawal
without notice, and represent goals and objectives only.

Copyright IBM Corp. 2007, 2012 235

The manufacturer's prices shown are the manufacturer's suggested retail prices, are current and are
subject to change without notice. Dealer prices may vary.

This information is for planning purposes only. The information herein is subject to change before the
products described become available.

This information contains examples of data and reports used in daily business operations. To illustrate
them as completely as possible, the examples include the names of individuals, companies, brands, and
products. All of these names are fictitious and any similarity to the names and addresses used by an
actual business enterprise is entirely coincidental.

If you are viewing this information in softcopy, the photographs and color illustrations may not appear.

The drawings and specifications contained herein shall not be reproduced in whole or in part without the
written permission of the manufacturer.

The manufacturer has prepared this information for use with the specific machines indicated. The
manufacturer makes no representations that it is suitable for any other purpose.

The manufacturer's computer systems contain mechanisms designed to reduce the possibility of
undetected data corruption or loss. This risk, however, cannot be eliminated. Users who experience
unplanned outages, system failures, power fluctuations or outages, or component failures must verify the
accuracy of operations performed and data saved or transmitted by the system at or near the time of the
outage or failure. In addition, users must establish procedures to ensure that there is independent data
verification before relying on such data in sensitive or critical operations. Users should periodically check
the manufacturer's support websites for updated information and fixes applicable to the system and
related software.

Trademarks
IBM, the IBM logo, and ibm.com are trademarks or registered trademarks of International Business
Machines Corp., registered in many jurisdictions worldwide. Other product and service names might be
trademarks of IBM or other companies. A current list of IBM trademarks is available on the Web at
Copyright and trademark information at www.ibm.com/legal/copytrade.shtml.

INFINIBAND, InfiniBand Trade Association, and the INFINIBAND design marks are trademarks and/or
service marks of the INFINIBAND Trade Association.

Linux is a registered trademark of Linus Torvalds in the United States, other countries, or both.

Other company, product, or service names may be trademarks or service marks of others.

Electronic emission notices

Class A Notices
The following Class A statements apply to the IBM servers that contain the POWER6 processor.

Federal Communications Commission (FCC) statement

Note: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of this

236 Finding parts, locations, and addresses

equipment in a residential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at his own expense.

Properly shielded and grounded cables and connectors must be used in order to meet FCC emission
limits. IBM is not responsible for any radio or television interference caused by using other than
recommended cables and connectors or by unauthorized changes or modifications to this equipment.
Unauthorized changes or modifications could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

Industry Canada Compliance Statement

This Class A digital apparatus complies with Canadian ICES-003.

Avis de conformit la rglementation d'Industrie Canada

Cet appareil numrique de la classe A respecte est conforme la norme NMB-003 du Canada.

European Community Compliance Statement

This product is in conformity with the protection requirements of EU Council Directive 2004/108/EC on
the approximation of the laws of the Member States relating to electromagnetic compatibility. IBM cannot
accept responsibility for any failure to satisfy the protection requirements resulting from a
non-recommended modification of the product, including the fitting of non-IBM option cards.

This product has been tested and found to comply with the limits for Class A Information Technology
Equipment according to European Standard EN 55022. The limits for Class A equipment were derived for
commercial and industrial environments to provide reasonable protection against interference with
licensed communication equipment.

European Community contact:

IBM Technical Regulations
Pascalstr. 100, Stuttgart, Germany 70569
Tele: 0049 (0)711 785 1176
Fax: 0049 (0)711 785 1283
E-mail: [email protected]

Warning: This is a Class A product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.

VCCI Statement - Japan

The following is a summary of the VCCI Japanese statement in the box above:

This is a Class A product based on the standard of the VCCI Council. If this equipment is used in a
domestic environment, radio interference may occur, in which case, the user may be required to take
corrective actions.
Appendix. Notices 237
Japanese Electronics and Information Technology Industries Association (JEITA)
Confirmed Harmonics Guideline (products less than or equal to 20 A per phase)

Japanese Electronics and Information Technology Industries Association (JEITA)

Confirmed Harmonics Guideline with Modifications (products greater than 20 A per
phase)

Electromagnetic Interference (EMI) Statement - People's Republic of China

Declaration: This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may need to perform practical action.

Electromagnetic Interference (EMI) Statement - Taiwan

The following is a summary of the EMI Taiwan statement above.

Warning: This is a Class A product. In a domestic environment this product may cause radio interference
in which case the user will be required to take adequate measures.

IBM Taiwan Contact Information:

238 Finding parts, locations, and addresses

Electromagnetic Interference (EMI) Statement - Korea

Please note that this equipment has obtained EMC registration for commercial use. In the event that it
has been mistakenly sold or purchased, please exchange it for equipment certified for home use.

Germany Compliance Statement

Deutschsprachiger EU Hinweis: Hinweis fr Gerte der Klasse A EU-Richtlinie zur

Elektromagnetischen Vertrglichkeit

Dieses Produkt entspricht den Schutzanforderungen der EU-Richtlinie 2004/108/EG zur Angleichung der
Rechtsvorschriften ber die elektromagnetische Vertrglichkeit in den EU-Mitgliedsstaaten und hlt die
Grenzwerte der EN 55022 Klasse A ein.

Um dieses sicherzustellen, sind die Gerte wie in den Handbchern beschrieben zu installieren und zu
betreiben. Des Weiteren drfen auch nur von der IBM empfohlene Kabel angeschlossen werden. IBM
bernimmt keine Verantwortung fr die Einhaltung der Schutzanforderungen, wenn das Produkt ohne
Zustimmung der IBM verndert bzw. wenn Erweiterungskomponenten von Fremdherstellern ohne
Empfehlung der IBM gesteckt/eingebaut werden.

EN 55022 Klasse A Gerte mssen mit folgendem Warnhinweis versehen werden:

"Warnung: Dieses ist eine Einrichtung der Klasse A. Diese Einrichtung kann im Wohnbereich
Funk-Strungen verursachen; in diesem Fall kann vom Betreiber verlangt werden, angemessene
Manahmen zu ergreifen und dafr aufzukommen."

Deutschland: Einhaltung des Gesetzes ber die elektromagnetische Vertrglichkeit von Gerten

Dieses Produkt entspricht dem Gesetz ber die elektromagnetische Vertrglichkeit von Gerten
(EMVG). Dies ist die Umsetzung der EU-Richtlinie 2004/108/EG in der Bundesrepublik Deutschland.

Zulassungsbescheinigung laut dem Deutschen Gesetz ber die elektromagnetische Vertrglichkeit von
Gerten (EMVG) (bzw. der EMC EG Richtlinie 2004/108/EG) fr Gerte der Klasse A.

Dieses Gert ist berechtigt, in bereinstimmung mit dem Deutschen EMVG das EG-Konformittszeichen
- CE - zu fhren.

Verantwortlich fr die Konformittserklrung nach des EMVG ist die IBM Deutschland GmbH, 70548
Stuttgart.

Appendix. Notices 239

Generelle Informationen:

Das Gert erfllt die Schutzanforderungen nach EN 55024 und EN 55022 Klasse A.

Electromagnetic Interference (EMI) Statement - Russia

Terms and conditions

Permissions for the use of these publications is granted subject to the following terms and conditions.

Personal Use: You may reproduce these publications for your personal, noncommercial use provided that
all proprietary notices are preserved. You may not distribute, display or make derivative works of these
publications, or any portion thereof, without the express consent of the manufacturer.

Commercial Use: You may reproduce, distribute and display these publications solely within your
enterprise provided that all proprietary notices are preserved. You may not make derivative works of
these publications, or reproduce, distribute or display these publications or any portion thereof outside
your enterprise, without the express consent of the manufacturer.

Except as expressly granted in this permission, no other permissions, licenses or rights are granted, either
express or implied, to the publications or any information, data, software or other intellectual property
contained therein.

The manufacturer reserves the right to withdraw the permissions granted herein whenever, in its
discretion, the use of the publications is detrimental to its interest or, as determined by the manufacturer,
the above instructions are not being properly followed.

You may not download, export or re-export this information except in full compliance with all applicable
laws and regulations, including all United States export laws and regulations.

THE MANUFACTURER MAKES NO GUARANTEE ABOUT THE CONTENT OF THESE

PUBLICATIONS. THESE PUBLICATIONS ARE PROVIDED "AS-IS" AND WITHOUT WARRANTY OF
ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED
WARRANTIES OF MERCHANTABILITY, NON-INFRINGEMENT, AND FITNESS FOR A PARTICULAR
PURPOSE.

240 Finding parts, locations, and addresses




Printed in USA