Scribd
Upload
406 views3 pages

DMS en BW

The document summarizes an electronic motor starter called the DMS03U and DMS05U that can start any single-phase motor up to 3HP or 5HP respectively. It calculates optimal startup times based on the motor and avoids unnecessary startups. It opens the start circuit if the motor is locked for over 0.5 seconds to prevent overheating or burning out. Connection and disconnection of the start capacitor occurs at zero voltage and current crossings to increase the capacitor's life.

Uploaded by

Quipuscoa Roger
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
406 views3 pages

DMS en BW

The document summarizes an electronic motor starter called the DMS03U and DMS05U that can start any single-phase motor up to 3HP or 5HP respectively. It calculates optimal startup times based on the motor and avoids unnecessary startups. It opens the start circuit if the motor is locked for over 0.5 seconds to prevent overheating or burning out. Connection and disconnection of the start capacitor occurs at zero voltage and current crossings to increase the capacitor's life.

Uploaded by

Quipuscoa Roger
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

ISOVOLT 3HPmax: DMS03U and 5HPmax: DMS05U

www.isovolt.com

DIGITAL MOTOR STARTER UP TO 5HP(4KW) UNIVERSAL


NEW ELECTRONIC CENTRIFUGAL SWITCH FOR ANY SINGLE PHASE
MOTOR UP TO 3HP(2.5KW) AND 5HP(4KW) 110/240VAC 50/60Hz

The smart replacement for any centrifugal switch used on any


motor type, voltage, power, RPM and frequency.
No more problems due to the lack of the specific centrifugal
switch that fits into your single phase motor.

The DMS05U module works on any single phase motor up to 5HP(4KW). TERMINALS
The DMS03U module works on any single phase motor up to 3HP(2.5KW). L - N: Are the power terminals
connected to the main power
Every startup time is mathematically calculated as a function of the motor cables that feeds the motor
type, voltage and loading condition. from 110 to 240V.
On high cycling condition (ON/OFF/ON) the motors coasting speed is They differ on the following:
measured avoiding any unnecessary startup or reduce it. Terminal L The line upon
which the start capacitor (CS)
Problems associated with RPM tolerance, mechanic and electrical fatigue, close/open circuit is made.
vibration, humidity, dust, etc. Are eliminated avoiding erratic motor startups. Terminal N The line upon
If there is a motor-locked condition during startup for more than 0.5s. which the start winding (LS)
The start circuit opens avoiding motor overheats or burn out. is referenced.
If there is a motor-locked condition during normal operation. It will not be A: Connected to the start
restarted unless the operator turns off the motor, find and fix the problem capacitor (CS) and start
and turn it on again. Avoiding motor overheats or burn out that will otherwise winding (LS) junction wire.
occur due to a mechanical centrifugal switch trying to restart the motor.
VANmax=800VAC - DMS05U
Connection and disconnection of the start capacitor (CS) are made at zero VANmax=700VAC - DMS03U
crossing of its voltage and current. After motors startup, the start capacitor
residual voltage is discharged increasing its life. C: Where the free end of the
start capacitor (CS) is wired.
Gaining maximum performance on continuous heavy duty work on: The DMS close/open the
Pumps, compressors, motor-tools, hoists, motorized doors and gate lifts that terminals C-L during startup.
uses single phase motors with centrifugal switches. No arcing contacts
VCLmax= 700VAC - DMS05U
allowing safe operation on hazardous and explosion proof environments.
VCLmax= 570VAC - DMS03U
Motors Power(HP) vs Start-Capacitor(uf) - Suggested values:
1/6 20 - 25
ICLmax value depends on motors
1/5 30 40 See app-note-002
startup time. Example 0.40s:
DMS05U ICLmax@25C= 350Amp
1/4 40 60 On www.isovolt.com
Pmax= 5HP Approved (Tested on 7HP)
1/3 60 80
DMS03U ICLmax@25C= 150Amp
1/2 80 100 SINPAC
Pmax= 3HP Approved (Tested on 5HP)
3/4 100 120 Compatible
1 120 160 Connection:
The module DMS must be installed
1.5 140 180 L- 2
using the included diagrams only by
2 160 - 220 C- 3
qualified technicians.
3 200 - 280 A- 4
4 240 - 360 N- 1
5 330 - 470
ISOVOLT

You might also like