Scribd
Upload
1K views

Vacuum Catch Pot

This document specifies the design and materials for a vacuum catch pot vessel. The catch pot has a working capacity of 850 liters and is designed to ASME Section VIII Division I standards. It will operate at normal pressures up to 5.5 kg/cm2 and temperatures up to 80°C, with a design pressure of 8 kg/cm2 and design temperature of 100°C. The catch pot has a torispherical shell and bottom closure with 3mm corrosion allowance and will be hydrostatically tested at 12 kg/cm2.

Uploaded by

sushant_jhawer
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
1K views

Vacuum Catch Pot

This document specifies the design and materials for a vacuum catch pot vessel. The catch pot has a working capacity of 850 liters and is designed to ASME Section VIII Division I standards. It will operate at normal pressures up to 5.5 kg/cm2 and temperatures up to 80°C, with a design pressure of 8 kg/cm2 and design temperature of 100°C. The catch pot has a torispherical shell and bottom closure with 3mm corrosion allowance and will be hydrostatically tested at 12 kg/cm2.

Uploaded by

sushant_jhawer
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
You are on page 1/ 1

SPECIFICATION VESSELS AND TANKS

DESCRIPTION VACUUM CATCH POT TYPE


DESIGN CODE ASME SEC VIII DIV I EQUIP NO. V - 123

CONTENT ORGANIC VAPOURS


CAPACITY
WORKING (LITER)
SERVICE DATA TOTAL (LITER) 850 SHELL HOT WATER JACKET

NORMAL / MAX OPERATING PRESS Kg / cm2) 5.5 / Full Vacuum 3


NORMAL / MAX OPERATING TEMP (C) 40 80

DESIGN PRESSURE (Kg/cm2) 8 4


DESIGN TEMPERATURE ( C) 100 100
SHELL CLOSURE TYPE (TOP) Std. Torispherical
SHELL CLOSURE TYPE (BOTTOM) Std. Torispherical
CORROSION ALLOWANCE mm 3 1
DESIGN DATA JOINT EFFICIENCY 0.85 0.7
RADIOGRAPHY (%) 10 Nil
STRESS RELIEVE Nil Nil
TEST PRESSURE (HYDRO / PNEU) (Kg/cm2) 12 6
WELDING PROCEDURE SMAW
SUPPORT ARRANGMENT 3 nos of legs

SHELL IS 2002/SA 515 GR 7 NOZZLE SA 106 GR C FLANGE SA - 105 GR C


MATERIAL OF JACKET IS 2002 NOZZLE SA 106 GR C FLANGE SA - 105 GR C
CONSTRUCTION SHELL CLOSURE IS 2002/SA 515 GR 70 JACKET CLOSURE IS 226
SUPPORTS ISMA 75 BOLTS & NUTS GASKET CAF

SHELL 900 1300


DIMENSIONS
JACKET 1000 1000, Covering bottom completely.

PAINTING Two Coats of Red Oxide Primer on exterior


INSULATION CLEATS, RINGS Required
OTHERS INSPECTION
OTHER ACCESSORIES BY VENDOR Name Plate, Lifting Lugs, Earthing Boss

NOZZLES SCHEDULE
NOZZLE SERVICE FLANGE NOZZLE NECK NOM SIZE
REMARKS
NO QTY STD RTG TYPE SCH PROJ (mm)
N1 1 Inlet ASA 150 RF 40 200 100
N2 1 Outlet ASA 150 RF 40 200 100
N3 1 Pressure Gauge ASA 150 RF 40 200 25
N4 1 Jacket Inlet ASA 150 RF 40 200 25
N5 1 Jacket Outlet ASA 150 RF 40 200 25
N6 1 Jacket Relief ASA 150 RF 40 200 25
N7 1 Drain ASA 150 RF 40 200 25
N8 1 Earthing Clip 50 50 6 SS - 304 20 mm hole strip
N9 1 Pressure Tramsmitter ASA 150 RF 40 200 20

You might also like