Scribd
Upload
50 views

Windload (Version 1) (Version 1)

The document summarizes the wind load calculations for a low-rise building with a roof slope of 4:12. It provides the velocity pressure, exposure category, and design wind pressure for various surfaces and frames/trusses of the building based on the given dimensions and wind speed of 150 kph. The maximum wind loads along the transverse and longitudinal directions are 5.18 kn/m and 4.02 kn/m respectively.

Uploaded by

Joe Mark Costan Avila
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
50 views

Windload (Version 1) (Version 1)

The document summarizes the wind load calculations for a low-rise building with a roof slope of 4:12. It provides the velocity pressure, exposure category, and design wind pressure for various surfaces and frames/trusses of the building based on the given dimensions and wind speed of 150 kph. The maximum wind loads along the transverse and longitudinal directions are 5.18 kn/m and 4.02 kn/m respectively.

Uploaded by

Joe Mark Costan Avila
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

WIND LOAD

Given:
Roof Slope = 4 : 12
L= 6.75 m
B= 21 m
7m
VELOCITY PRESSURE

qz = 47.3 x 10^-1 kz kzt kd V^2 Iw

kz = 2.01 ( z/zg ) zg = 275 7m


(Table 207 - 5 ; Table 207 - 4)
kz = 0.94 = 9.5

EXPOSURE CATEGORY = C
kzt = 1 (Not near to any topographic formation)
kd = 0.85 (Table 207 - 2) 7m
V= 150 kph (Fig. 207 - 24)
Iw = 1 (Table 207 - 3)

qz = 47.3 x 10^-1 kz kzt kd V^2 Iw 6.75 m


qz = 0.85 kPa

y= m

y/6.75 = 4/12
y= 1.125 m 3.5 m

= tan-1(y/(L/2))
= 0.32 rad 3.5 m
= 18.43 deg

z = h = h1 + h2 + y/2 6.75 m
z=h= 7.56 m
FOR LOW RISE BUILDINGS CASE 1 TO 8:
W= PRESSURE X TRIBUTARY WIDTH
DESIGN WIND PRESSURE
P = qh[GCpf - Gcpi] TRANSVERSE DIRECTION:

Gcpi = 0.18 -0.18 (Enclosed Buildings) (Fig. 207 - 5)


G= 0.85
* Values are linearly interpolated from Fig. 207- 10. 3
* Tortional Load Cases need not be considered since the height of the building is less than 10m. 2
CASE 1 to 8 (A) 3E
SURFACE GCpf Gcpi P (kPa) 0.1L = 0.675 4E 4 2E
1 0.52 0.18 0.29 0.4h = 3.025 1 2
2 -0.69 0.18 -0.74 note : smaller will governs
3 -0.47 0.18 -0.55 1E
4 -0.42 0.18 -0.51
5 -0.45 0.18 -0.54 1
6 -0.45 0.18 -0.54 ALONG GRID 1 ALONG GRID 2
1E 0.78 0.18 0.51 TRIBUTARY WIDTH = 1.35 m TRIBUTARY WIDTH = 7m
2E -1.07 0.18 -1.06 1.43 Kn/m 5.18 Kn/m
3E -0.67 0.18 -0.72 0.98 kn/m 3.87 kn/m
4E -0.62 0.18 -0.68

0.69 kn/m 0.92 kn/m 2.023 kn/m 3.57 kn/m


0.72 kn/m 3.75 kn/m
CASE 9 to 16 (B)

SURFACE GCpf Gcpi P (kPa) CASE 9 TO 16:


1 0.52 -0.18 0.60 W= PRESSURE X TRIBUTARY WIDTH
2 -0.69 -0.18 -0.43
3 -0.47 -0.18 -0.25 TRANSVERSE DIRECTION:
4 -0.42 -0.18 -0.20 6
5 -0.45 -0.18 -0.23
6 -0.45 -0.18 -0.23
1E 0.78 -0.18 0.82 3
2E -1.07 -0.18 -0.76 2
3E -0.67 -0.18 -0.42 3E
4E -0.62 -0.18 -0.37 4E 4 2E
1 2

1E
5
1
ALONG GRID 1 ALONG GRID 2
TRIBUTARY WIDTH = 1.35 m TRIBUTARY WIDTH = 6.75 m
1.02 Kn/m 2.93 Kn/m
0.56 kn/m 1.66 kn/m

1.10 kn/m 0.50 kn/m 4.02 kn/m 1.38 kn/m


0.31 kn/m 1.55 kn/m
DESIGN WIND LOAD SUMMARY PER FRAMES & TRUSSES

SURFACE (LOAD KN/M)


FRAME DIRECTION
1 2 3 4 5 6 1E 2E 3E 4E

1 X - Direction 2.02 5.18 3.87 3.57 3.75 0.72 0.69 1.43 0.98 0.92

2 X - Direction 2.02 5.18 3.87 3.57 3.75 0.72 0.69 1.43 0.98 0.92

3 X - Direction 2.02 5.18 3.87 3.57 3.75 0.72 0.69 1.43 0.98 0.92

4 X - Direction 2.02 5.18 3.87 3.57 3.75 0.72 0.69 1.43 0.98 0.92

SURFACE (LOAD KN/M)


FRAME DIRECTION
1 2 3 4 5 6 1E 2E 3E 4E

A Y - Direction 4.02 2.93 1.66 1.38 1.55 0.31 1.10 1.02 0.56 0.50

B Y - Direction 4.02 2.93 1.66 1.38 1.55 0.31 1.10 1.02 0.56 0.50

You might also like