7/12/14 Electrical Interview Questions-Interview Questions and Answers-25066

Placement Papers Aptitude Preparation Interview Preparation General Knowledge Online Test Buy Now
P3Home > Interview Preparation > Technical Interview Prep > Electrical Interview Questions > Electrical Interview Questions

Learn and
More from this lesson Electrical Interview Questions Likepractice
8.3k Share
Technical Interview Prep, Interview Preparation, Electrical
160032 views, 1905 found it usefulInterview Questions questions and answers with explanation for
Electrical Questions from AC-
interview,placement test,online test,competitive examination
DC Motors
and entrance test
Electrical Questions from
power electronics Review a list of frequently asked Electrical interview questions for electrical graduates. Frequently
asked interview questions with answers under the subjects like electrical machines,Transmission
and distribution,Power electronics and some general basic questions.

Technical Interview Prep

1. What is a System?
Technical Interview-
Introduction When a number of elements or components are connected in a sequence to perform a specific
function, the group of elements that all constitute a System
C Interview Questions

C++ Interview Questions | Free

2. What is Control System?
C# Interview Questions
In a System the output and inputs are interrelated in such a manner that the output quantity or
DBMS Interview Questions variable is controlled by input quantity, then such a system is called Control System.
The output quantity is called controlled variable or response and the input quantity is called
OS Interview Questions command signal or excitation.
Java Interview Questions

.Net Interview Questions 3. What are different types of Control Systems?

PHP Interview Questions Two major types of Control Systems are 1) Open loop Control System 2) Closed Loop Control
Systems
Networking Interview
Open loop Control Systems:The Open loop Control System is one in which the Output Quantity has
Questions
no effect on the Input Quantity. No feedback is present from the output quantity to the input quantity
Software Testing Interview for correction.
Questions Closed Loop Control System:The Closed loop Control System is one in which the feedback is
provided from the Output quantity to the input quantity for the correction so as to maintain the
Data Structure Interview
desired output of the system.
Questions

Algorithms Interview Questions

4. What is a feedback in Control System?
Electrical Interview Questions
The Feedback in Control System in one in which the output is sampled and proportional signal is fed
Electronics Interview back to the input for automatic correction of the error ( any change in desired output) for futher
Questions
processing to get back the desired output.
Mechanical Interview
Questions

Civil 5. Why Negative Feedback is preffered in the Control System?

The role of Feedback in control system is to take the sampled output back to the input and compare
output signal with input signal for error ( deviation from the desired result).
Negative Feedback results in the better stability of the system and rejects any disturbance signals
and is less sensitive to the parameter variations. Hence in control systems negative feedback is

considered.

6. What is the effect of positive feedback on stability of the system?

Positive feedback is not used generally in the control system because it increases the error signal
and drives the system to instability. But positive feedbacks are used in minor loop control systems
to amplify certain internal signals and parameters

7. What is Latching current?

Gate signal is to be applied to the thyristor to trigger the thyristor ON in safe mode. When the
thyristor starts conducting the forward current above the minimum value, called Latching current, the
gate signal which is applied to trigger the device in no longer require to keep the scr in ON position.

8. What is Holding current ?

When scr is conducting current in forward conduction state, scr will return to forward blocking state
when the anode current or forward current falls below a low level called Holding current
Note: Latching current and Holding current are not same. Latching current is associated with the
turn on process of the scr whereas holding current is associated with the turn off process. In general
holding current will be slightly lesser than the latching current.

9. Why thyristor is considered as Charge controlled device?

During the triggering process of the thyristor from forward blocking state to forward conduction state
through the gate signal, by applying the gate signal (voltage between gate and cathode) increases
the minority carrier density in the p-layer and thereby facilitate the reverse break over of the junction
J2 and thyristor starts conducting. Higher the magnitude of the gate current pulse, lesser is the time
required to inject the charge and turning on the scr. By controlling the amount of charge we can
control the turning on time of the scr.

10. What are the different losses that occur in thyristor while operating?

placement.freshersworld.com/power-preparation/technical-interview-preparation/electrical-interview-questions-25066 1/5
7/12/14 Electrical Interview Questions-Interview Questions and Answers-25066
Different losses that occur are
a)Forward conduction losses during conduction of the thyristor
b)Loss due to leakage current during forward and reverse blocking.
c)Power loss at gate or Gate triggering loss.
d)Switching losses at turn-on and turn-off.

11. What is meant by knee point voltage?

Knee point voltage is calculated for electrical Current transformers and is very important factor to
choose a CT. It is the voltage at which a CT gets saturated.(CT-current transformer).

12. What is reverse power relay?

Reverse Power flow relay are used in generating stations's protection. A generating stations is
supposed to fed power to the grid and in case generating units are off,there is no generation in the
plant then plant may take power from grid. To stop the flow of power from grid to generator we use
reverse power relay.

13. What will happen if DC supply is given on the primary of a transformer?

Mainly transformer has high inductance and low resistance.In case of DC supply there is no
inductance ,only resistance will act in the electrical circuit. So high electrical current will flow
through primary side of the transformer.So for this reason coil and insulation will burn out.

14. What is the difference between isolators and electrical circuit breakers? What is bus-
bar?
Isolators are mainly for switching purpose under normal conditions but they cannot operate in fault
conditions .Actually they used for isolating the CBs for maintenance. Whereas CB gets activated
under fault conditions according to the fault detected.Bus bar is nothing but a junction where the
power is getting distributed for independent loads.

15. What are the advantage of free wheeling diode in a Full Wave rectifier?
It reduces the harmonics and it also reduces sparking and arching across the mechanical switch so
that it reduces the voltage spike seen in a inductive load.

16. Mention the methods for starting an induction motor?

The different methods of starting an induction motor:
a)DOL:direct online starter
b)Star delta starter
c)Auto transformer starter
d)Resistance starter
e)Series reactor starter

17. What is the power factor of an alternator at no load?

At no load Synchronous Impedance of the alternator is responsible for creating angle difference. So
it should be zero lagging like inductor.

18. What is the function of anti-pumping in circuit breaker?

When breaker is close at one time by close push button,the anti pumping contactor prevent re close
the breaker by close push button after if it already close.

19. What is stepper motor.what is its uses?

Stepper motor is the electrical machine which act upon input pulse applied to it. it is one type of
synchronous motor which runs in steps in either direction instead of running in complete cycle.so, in
automation parts it is used.

20. There are a Transformer and an induction machine. Those two have the same supply.
For which device the load current will be maximum? And why?
The motor has max load current compare to that of transformer because the motor consumes real
power.. and the transformer is only producing the working flux and its not consuming.. hence the
load current in the transformer is because of core loss so it is minimum.

21. What is SF6 Circuit Breaker?

SF6 is Sulpher hexa Flouride gas.. if this gas is used as arc quenching medium in a Circuitbreaker
means SF6 CB.

22. What is ferrantic effect?

Output voltage is greater than the input voltage or receiving end voltage is greater than the sending
end voltage.

23. What is meant by insulation voltage in cables? explain it?

It is the property of a cable by virtue of it can withstand the applied voltage without rupturing it is
known as insulation level of the cable.

24. What is the difference between MCB & MCCB, Where it can be used?
placement.freshersworld.com/power-preparation/technical-interview-preparation/electrical-interview-questions-25066 2/5
7/12/14 Electrical Interview Questions-Interview Questions and Answers-25066
24. What is the difference between MCB & MCCB, Where it can be used?
MCB is miniature circuit breaker which is thermal operated and use for short circuit protection in
small current rating circuit. MCCB moulded case circuit breaker and is thermal operated for over
load current and magnetic operation for instant trip in short circuit condition.under voltage and under
frequency may be inbuilt. Normally it is used where normal current is more than 100A.

25. Where should the lighting arrestor be placed in distribution lines?

Near distribution transformers and out going feeders of 11kv and incomming feeder of 33kv and near
power transformers in sub-stations.

26. Define IDMT relay?

It is an inverse definite minimum time relay.In IDMT relay its operating is inversely proportional and
also a characteristic of minimum time after which this relay operates.It is inverse in the sense ,the
tripping time will decrease as the magnitude of fault current increase.

27. What are the transformer losses?

TRANSFORMER LOSSES - Transformer losses have two sources-copper loss and magnetic loss.
Copper losses are caused by the resistance of the wire (I2R). Magnetic losses are caused by eddy
currents and hysteresis in the core. Copper loss is a constant after the coil has been wound and
therefore a measurable loss. Hysteresis loss is constant for a particular voltage and current. Eddy-
current loss, however, is different for each frequency passed through the transformer.

28. what is the full form of KVAR?

We know there are three types of power in Electricals as Active, apparent & reactive. So KVAR is
stand for ``Kilo Volt Amps with Reactive component.

29. Two bulbs of 100w and 40w respectively connected in series across a 230v supply which
bulb will glow bright and why?
Since two bulbs are in series they will get equal amount of electrical current but as the supply
voltage is constant across the bulb(P=V^2/R).So the resistance of 40W bulb is greater and voltage
across 40W is more (V=IR) so 40W bulb will glow brighter.

30. Why temperature rise is conducted in bus bars and isolators?

Bus bars and isolators are rated for continuous power flow, that means they carry heavy currents
which rises their temperature. so it is necessary to test this devices for temperature rise.

31. What is the difference between synchronous generator & asynchronous generator?
In simple, synchronous generator supply's both active and reactive power but asynchronous
generator(induction generator) supply's only active power and observe reactive power for
magnetizing.This type of generators are used in windmills.

32. What is Automatic Voltage regulator(AVR)?

AVR is an abbreviation for Automatic Voltage Regulator.It is important part in Synchronous
Generators, it controls theoutput voltage of the generator by controlling its excitation current. Thus it
can control the output Reactive Power of the Generator.

33. Difference between a four point starter and three point starter?
The shunt connection in four point stater is provided separately form the line where as in three point
stater it is connected with line which is the drawback in three point stater

34. Why the capacitors works on ac only?

Generally capacitor gives infinite resistance to dc components(i.e., block the dc components). it
allows the ac components to pass through.

35. How many types of colling system it transformers?

1. ONAN (oil natural,air natural)
2. ONAF (oil natural,air forced)
3. OFAF (oil forced,air forced)
4. ODWF (oil direct,water forced)
5. OFAN (oil forced,air forced)

36. Operation carried out in Thermal power stations?

The water is obtained in the boiler and the coal is burnt so that steam is obtained this steam is
allowed to hit the turbine , the turbine which is coupled with the generator generates the electricity.

37. What is 2 phase motor?

A two phase motor is a motor with the the starting winding and the running winding have a phase
split. e.g;ac servo motor.where the auxiliary winding and the control winding have a phase split of 90
degree.

38. What is the principle of motor?

Whenever a current carrying conductor is placed in an magnetic field it produce turning or twisting
movement is called as torque.
placement.freshersworld.com/power-preparation/technical-interview-preparation/electrical-interview-questions-25066 3/5
7/12/14 Electrical Interview Questions-Interview Questions and Answers-25066
movement is called as torque.

39. What is meant by armature reaction?

The effect of armature flu to main flux is called armature reaction. The armature flux may support
main flux or opposes main flux.

40. What is the difference between synchronous generator & asynchronous generator?
In simple, synchronous generator supply's both active and reactive power but asynchronous
generator(induction generator) supply's only active power and observe reactive power for
magnetizing.This type of generators are used in windmills.

41. Whats is MARX CIRCUIT?

It is used with generators for charging a number of capacitor in parallel and discharging them in
series.It is used when voltage required for testing is higher than the available.

42. What are the advantages of speed control using thyristor?

Advantages :
1. Fast Switching Characterstics than Mosfet, BJT, IGBT
2. Low cost
3. Higher Accurate.

43. What is ACSR cable and where we use it?

ACSR means Aluminium conductor steel reinforced, this conductor is used in transmission &
distribution.

44. Whats the one main difference between UPS & inverter ? And electrical engineering &
electronics engineering ?
Uninterrupt power supply is mainly use for short time . means according to ups VA it gives backup.
ups is also two types : on line and offline . online ups having high volt and amp for long time backup
with with high dc voltage.but ups start with 12v dc with 7 amp. but inverter is startwith 12v,24,dc to
36v dc and 120amp to 180amp battery with long time backup.

45. What will happen when power factor is leading in distribution of power?
If their is high power factor, i.e if the power factor is close to one:
a)Losses in form of heat will be reduced,
b)Cable becomes less bulky and easy to carry, and very cheap to afford, &
c)It also reduces over heating of tranformers.

46. What are the advantages of star-delta starter with induction motor?
(1). The main advantage of using the star delta starter is reduction of current during the starting of
the motor.Starting current is reduced to 3-4 times Of current of Direct online starting.(2). Hence the
starting current is reduced , the voltage drops during the starting of motor in systems are reduced.

47. Why Delta Star Transformers are used for Lighting Loads?
For lighting loads, neutral conductor is must and hence the secondary must be star winding. and
this lighting load is always unbalanced in all three phases. To minimize the current unbalance in the
primary we use delta winding in the primary. So delta / star transformer is used for lighting loads.

48. Why computer humming sound occurred in HT transmission line?

This computer humming sound is coming due to ionization (breakdown of air into charged particles)
of air around transmission conductor. This effect is called as Corona effect, and it is considered as
power loss.

49. What is rated speed?

At the time of motor taking normal current (rated current)the speed of the motor is called rated

speed. It is a speed at which any system take small current and give maximum efficiency.

50. If one lamp connects between two phases it will glow or not?
If the voltage between the two phase is equal to the lamp voltage then the lamp will glow. When the
voltage difference is big it will damage the lamp and when the difference is smaller the lamp will glow
depending on the type of lamp.

Found This Useful ? : Yes No << Previous Next >>

Read more

Interview tips Job interview Interview preparation

Phone interview Interview preparation Tips Interview Preparation and basic tips

4 different parts of interview preparation How To Dress For Your Next Job Interview Interview body language

Bank Interview questions & Answers Group Discussion Topics Group discussion tips

placement.freshersworld.com/power-preparation/technical-interview-preparation/electrical-interview-questions-25066 4/5
7/12/14 Electrical Interview Questions-Interview Questions and Answers-25066
Types of Group Discussion HR interview questions

Jobs Placement Preparation Career & Courses

JOBS BY CATEGORY JOBS BY COURSES SAMPLE PLACEMENT PAPERS HIGHER STUDIES IN INDIA TRAINING COURSES
IT / Software Jobs BE / B.Tech Jobs Placement Papers M.Tech Java / J2EE
Core Technical Jobs MCA Jobs Selection Procedure MBA PHP / MySQL
Government Sector Jobs MBA / PGDM Jobs Company Profiles MCA SEO / Web Designing
Defence Jobs ME / M.Tech Jobs Latest Papers TEST PREPARATION Assembly Language
Research Jobs M.Sc Jobs IT Companies GRE Android Development
BPO Jobs B.Com Jobs Non IT Companies BlackBerry Development
GMAT
Bank Jobs BBA / BBM Jobs Bank Papers CAT / MAT iPhone Development
Dream Jobs> 5 lpa BCA Jobs IELTS / TOEFL Mobile Testing
Walk-ins Jobs B.Sc Jobs POWER PLACEMENT PREPARATION Wireless Technology
GATE
Manpower Consultants Diploma Jobs Aptitude Preparation Defence MicroSoft(MS) SQL
Teaching Jobs JOBS BY CITIES General Knowledge Civil Services Microsoft(MS) Access
1-3 Years Exp.Jobs Interview Preparation HTML / JavaSript / CSS / Ajax
Jobs in Ahmedabad STUDIES ABROAD
Jobs in Bangalore Online Tests Joomla / Drupal / Wordpress
USA
Archived Job Jobs in Chennai IT Companies Preparation ASP
Australia
Job Results Jobs in Delhi / NCR GATE Preparation ASP.NET / C#
UK
Jobs by Company Jobs in Hyderabad CAT Preparation C
New Zealand
Jobs by Branches Jobs in Kolkata Bank Exam Preparation C++
Canada
Jobs by Roles Jobs in Mumbai PSU Companies Preparation
Singapore List your Institute here
Jobs by Skills
Jobs in Pune
Internships Jobs in Gurgaon
Scholarships Jobs in Noida
Success Stories

Candidate Services

Freshersworld.com : The No.1 Jobsite for Freshers in India

Freshersworld.com is the No.1 Jobsite for freshers in India with more than 3500+ top companies hiring through
Freshersworld.com. Freshersworld is a one-stop shop for all your career needs, right from your campus interview
preparation till the final selection in your dream company.

Get in Touch

About Us | Blog | FAQs | Advertise With Us | Recruitment Solutions | Contact Us

Terms of Use | Privacy Policy | Copyright | Sitemap 2000 - 2013 Freshersworld.com

placement.freshersworld.com/power-preparation/technical-interview-preparation/electrical-interview-questions-25066 5/5