Scribd
Upload
111 views

Figure 1 Velocity Boundary Layer Over A Flat Plate

At a 30 degree angle of attack, flow separation occurs on the top surface of the airfoil, dramatically changing the pressure distribution and causing the airfoil to stall. The boundary layer separates more readily at higher angles of attack, reducing lift and increasing drag. To recover from a stall, the plane must dive to regain laminar flow over the wing and restore the pressure differential producing lift.

Uploaded by

Elora Sofea
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
111 views

Figure 1 Velocity Boundary Layer Over A Flat Plate

At a 30 degree angle of attack, flow separation occurs on the top surface of the airfoil, dramatically changing the pressure distribution and causing the airfoil to stall. The boundary layer separates more readily at higher angles of attack, reducing lift and increasing drag. To recover from a stall, the plane must dive to regain laminar flow over the wing and restore the pressure differential producing lift.

Uploaded by

Elora Sofea
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

1.

Explain about the boundary layer thickness in the boundary layer of both surfaces

Figure 1 velocity boundary layer over a flat plate

Effect of roughness on boundary layer with different roughness gives us a nice


understanding that increasing the roughness of the flat plate, increasing the boundary layer
thickness. Compare to rough surface, the viscosity effect is higher. It is due to the
frictional forces from that surface is very high so that it will increase the boundary layer
thickness of the fluid motion. For a smooth surface, the value of boundary layer thickness
is small. The viscosity effect from smooth surface are only provide small consequence on
the thickness. In real engineering flows, transition to turbulent flows usually happen more
abruptly and also much earlier which in the lower value of than the values given for
smooth flat plate with a calm free stream. The factor such as roughness surface will be
contributed to an earlier transition location. Because the engineering Reynolds number of
= is often used to determine the boundary layer most likely to be laminar (< or likely
turbulent (>). Whereas for the case of smooth surface with clean condition, the critical
Reynolds number for transition to turbulent is 1.

2. Explain differences in terms of results for smooth and rough surfaces.

3. How can we tell whether the flow is turbulent or laminar


Laminar flow generally happens when dealing with small pipes and low flow velocities
whereas Turbulent flow happens in general at high flow rates and with larger pipes.
Turbulent and laminar flow can be differentiated by using Reynolds Number, Re.

ud
Re

where r = density, u = mean velocity, d = diameter and m = viscosity

would help predict the change in flow type. If the value is less than about 2000 then flow
is laminar, if greater than 4000 then turbulent and in between these then in the transition
zone.

Laminar flow: Re < 2000

Transitional flow: 2000 < Re < 4000

Turbulent flow: Re > 4000

4. What is the distance in the plate before the flow becomes turbulent?

As the boundary layer thickness becomes greater, so the velocity gradient become smaller
and the shear stress decreases until it is no longer enough to drag the slow fluid near the
surface along. If this viscous force was the only action then the fluid would come to a rest.
It, of course, does not come to rest but the second mechanism comes into play. Up to this
point the flow has been laminar and Newton's law of viscosity has applied. This part of the
boundary layer is known as the laminar boundary layer. The viscous shear stresses have
held the fluid particles in a constant motion within layers. At certain distances, they
become small as the boundary layer increases in thickness and the velocity gradient gets
smaller. Eventually they are no longer able to hold the flow in layers and the fluid starts to
rotate.
This causes the fluid motion to rapidly becomes turbulent. Fluid from the fast moving
region moves to the slower zone transferring momentum and thus maintaining the fluid by
the wall in motion. Conversely, slow moving fluid moves to the faster moving region
slowing it down. The net effect is an increase in momentum in the boundary layer. We call
the part of the boundary layer the turbulent boundary layer.

5. What happened to the aerofoil profile at 30o angle of attach compared to the normal
position?

Normal flow over a aerofoil is shown in the figure below with the boundary layers greatly
exaggerated.

The velocity increases as air it flows over the wing. The pressure distribution is similar to
that shown below so transverse lift force occurs.

If the angle of the wing becomes too great and boundary layer separation occurs on the top
of the aerofoil the pressure pattern will change dramatically. This phenomenon is known
as stalling.
When stalling occurs, all, or most, of the 'suction' pressure is lost, and the plane will
suddenly drop from the sky. The only solution to this is to put the plane into a dive to
regain the boundary layer. A transverse lift force is then exerted on the wing which gives
the pilot some control and allows the plane to be pulled out of the dive.
Normally at 25o angle and above creates a high lift coefficient due to separated flow going
through the pattern creating lift force. The relation between the lift coefficients can be
claimed as lift coefficient versus angle of attack. As angle pf attack increases, separated
regions on top of the profile increase in size and hinder its properties to create lift. At
critical angel separated flow can be dominant that any further increase created more drag
and less lift on the profile.

You might also like