Scribd
Upload
422 views

Technical Specifications Metals

The document provides technical specifications for metals used in construction. It outlines materials like structural steel, bolts, nuts and welding electrodes that must meet standards from organizations like ASTM and AWS. Fabrication requirements include submitting shop drawings for approval, ensuring clean cuts and holes, and welding according to AWS codes. Erection must be true, straight and plumb, using tools like drift pins and wedges, and limiting errors to 1 in 500. Gas cutting for corrections requires approval.

Uploaded by

shem4fun
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
422 views

Technical Specifications Metals

The document provides technical specifications for metals used in construction. It outlines materials like structural steel, bolts, nuts and welding electrodes that must meet standards from organizations like ASTM and AWS. Fabrication requirements include submitting shop drawings for approval, ensuring clean cuts and holes, and welding according to AWS codes. Erection must be true, straight and plumb, using tools like drift pins and wedges, and limiting errors to 1 in 500. Gas cutting for corrections requires approval.

Uploaded by

shem4fun
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

TECHNICAL SPECIFICATIONS

METALS
Scope
The work includes, furnishing, fabrication, erection or installation, complete of all
structural steel and miscellaneous metal work in accordance with this specification
unless required otherwise in the drawings.

Applicable Documents
The following specifications and standards (latest edition) but referred to hereinafter by
basic designation only shall form part of this specification:

ASTM American Society for Testing and Materials

A36 Structural Steel Specification for


A36M-88

A307-87 Bolts and Studs 60,000 psi Tensile Strength

A325-88 Standard Specification, High Strength Bolts for Joints

A570-85 Hot-Rolled Carbon Steel Sheet and Strip, Structural


Quality

A611-85 Steel, Cold-Rolled Sheet, Carbon, Structural Quality

AWS American Welding Society

D1. 1-85 Structural Welding Code, Steel

AISC American Institute of Steel Construction


Specification for the Design, Fabrication
Erection of Structural Steel for Buildings

AISI American Iron and Steel Institute


Specification for the Design, Fabrication
Erection of Structural Steel for Buildings

Requirements

1 General
The Contractor shall submit to the Engineer for approval shop drawings showing the
proposed re-alignment, replacement, fabrication and installation of all metal work. No
work shall be started until the shop drawings have been approved, and all works shall
conform to the approved shop drawings.
2 Materials
1) Structural steel shapes, plates and bars, unless otherwise shown or specified on the
drawings shall conform to ASTM specification
A36/A36M.

2) Hot-formed steel sheet and strip, unless otherwise shown or specified on the
drawings shall conform to ASTM A570.

3) Bolts, nuts and washers shall conform to specification ASTM A307, with a minimum
yield point of 33,000 psi, unless otherwise shown or specified in the drawings. Heavy
hexagonal bolts, hexagonal nuts and hardened washers, shall be quenched and
tempered medium, carbon steel bolts, nuts and washers complying with ASTM A325

4) Screws and expansion bolts shall be of a standard commercial grade, as approved


by the Engineer, and of the sizes and types indicated.

5) Electrodes for arc welding shall be E60 or E70. AWS D1.1.

6) Miscellaneous metal items including accessories, incidentals, fastenings and


anchorages not mentioned herein, or in other sections but are required to complete
work, and for which there are no detail drawings, shall be provided and installed in
accordance with standard practice of the trades as approved by the Engineer.

3 Fabrication
The work shall be well formed to the shape and size shown and assembled as detailed.
Structural members shall be fabricated and assembled to the greatest extent possible.
Shearing and punching shall produce a clean, true lines and surfaces with burrs
removed. Nuts shall be drawn up tight. Joints which are to be exposed to the weather
shall be watertight. Holes shall be cut, drilled, or punched at right angles to the surface
of the metal and shall not be made or enlarged by burning. Holes in base or bearing
plates shall be drilled.

3.1 Welding of structural steel shall be in accordance with the standard code of
Arc and Gas Welding in Building Construction of the American Welding
Society. All welding works shall be performed by qualified welders only.

3.2 Shop painting. Unless otherwise specified or indicated in the drawings, all
structural steel work (except galvanized surfaces and surfaces that will be
painted with epoxy) shall be given a shop coat of red lead or zinc chromate
primer.

4 Erection
The steel structure shall be erected true to line and grades. Bracings and supports shall
be introduced whenever necessary to take care of all the loads to which the structure
may be subjected. Such bracings shall be left in place as may be required for safety. As
erection progresses, the work shall be bolted to take care of all the dead loads, wind
and erection stresses. No reaming of undersize bolt holes will be permitted, and
erection bolts shall not be used for lining up members.

4.1 Drift pins.


Drift pins may be used only to bring together several parts, they shall not be used
in such manner as to distort or damage the metal.

4.2 Gas cutting.


The use of gas cutting torch in the field for correcting fabrication errors shall not
be permitted on any major member in the structural framing. Its use may be
permitted only when the member is not under stress, and subject to the approval
of the Engineer.

4.3 Base plates and bearing plates.


Base plates and large bearing plates shall be supported on steel wedges or
shims until the supported member have been plumbed, following which the entire
bearing area shall be grouted with non-shrink cement grout.

4.4 Setting up.


Steel shall be erected plumb, level and properly guyed. In setting or erecting of
structural steel, the individual piece shall be considered plumb or level where the
error does not exceed 1 to 500.

You might also like