www.atos.

com Table TE015-2/E

Solenoid directional valves with low power consumption

Direct operated, ISO 4401 size 06

On-off directional valves derived from stan-

dard versions and equipped with low power
consumption solenoids. They permits a con-
siderable energy saving and they can be
directly operated from the output stage of the
machine control system (PLC I/O modules)

Two models are available:

- DHE, 15W power, spool type, max opera-
ting limits 40 l/min, 210 bar
- DHO, 8W power, spool type, max opera-
DHE-0631/2/15W-X24DC ting limits 50 l/min, 250 bar

For DHE the coils can be easily replaced

without tools. The coils are fully encapsula-
ted according to temperature class H.

Applicatons
Machine tools, marine system

Surface mounting ISO 4401 size 06

DHO-0611/8W-X24DC
DHO-0711/8W-X24DC (dotted line)

1 MODEL CODE OF SPOOL TYPE DIRECTIONAL VALVES

DHO - 0 61 1 / 8W / A - X 24DC ** /*
Directional control valves Seals material
ISO 4401 size 06 - = NBR
DHE-0 = for DC supply PE = FKM
DHO-0 = for DC supply with
improved performances Series number
Valve configuration, see table 
61 = single solenoid, center plus external Voltage code
position, spring centered 24DC = 24VDC
63 = single solenoid, 2 external positions,
spring offset
67 = single solenoid, center plus external X = without connector
position, spring offset See note 1 at section  for available connectors, to be
71 = double solenoid, 3 positions, spring ordered separately
centered
Other configurations are available on request

Spool type, see table  Options

A = Solenoid mounted at side of port B (only for single solenoid valves).
Solenoid power 15W = for DHE 8W = for DHO In standard versions, solenoid is mounted at side of port A.

2 CONFIGURATIONS and SPOOLS

Configurations Spools Configurations Spools

61
1 0 2 1 0 2 1 0 2 1 0 2 1 0 2
1 0

61/A
0 1 3 4
0 2 63 0/2
1 2
67
0 2 5 6 7 8 63/A 1/2
1 2
67/A
1 0 16 17 58 2/2

71

1 0 2

TE015
 3 MAIN CHARACTERISTICS OF DHE /15W AND DHO /8W DIRECTIONAL VALVES

Assembly position / location Any position

Subplate surface finishing Roughness index Ra 0,4 - flatness ratio 0,01/100 (ISO 1101)
Ambient temperature from -20C to +70C
Fluid Hydraulic oil as per DIN 51524 .... 535; for other fluids see section 
Recommended viscosity 15 100 mm2/s at 40C (ISO VG 15 100)
Fluid contamination class ISO 4401 class 21/19/16 NAS 1638 class 10, in line filters of 25 m (25 75 recommended)
Fluid temperature -20C +60C (standard seals) -20C +80C (/PE seals)
Flow direction As shown in the symbols of tables 
Operating pressure
Ports P,A,B: 350 bar;
DHE, DHO
Port T: 210 bar

Rated flow See diagrams Q/p at section 

Maximum flow 40 l/min for DHE; 50 l/min for DHO; see operating limits at section 

3.1 Coils characteristics

Insulation class H (180C) Due to the occuring surface temperatures of the solenoid coils, the European standards
EN ISO 13732-1 and EN ISO 4413 must be taken into account
Connector protection degree DIN 43650 IP 65
Relative duty factor 100%
Supply voltage tolerance 10%

4 NOTES
1 Type of electric/electronic connector DIN 43650, to be ordered separately
666 = standard connector IP-65, suitable for direct connection to electric supply source.
667 = as 666, but with built-in signal led.

2 Spools
- spools type 0/2, 1/2 and 2/2 are only used for two position valves: single solenoid valves, type DH*-063*/2

5 Q/P DIAGRAMS based on mineral oil ISO VG 46 at 50C

Flow direction DHE DHO
E E
PA PB AT BT PT
Spool type
D
D
Valve pressure drop p [bar]

Valve pressure drop p [bar]

0, 0/1, 6, 7, 8 A A A A B
C
0/2, 1, 1/2, 2, 3 B B B B
C B
4, 5 D D C C D
A
2/2 E E
B
Based on fluid viscosity of 43 mm2/s at 40C. A

Flow rate [l/min] Flow rate [l/min]

6 OPERATING LIMITS
The diagrams have been obtained with DHE DHO
warm solenoids and power supply at lowest 250 300
value (V nom - 10%). The curves refer to
A A
application with symmetrical flow through the
200 240
valve (i.e. P A and B T). In case of
Inlet pressure [bar]

Inlet pressure [bar]

asymmetric flow the operating limits must be B

reduced. B
150 180
C C
D
100 120
DHE, DHO D
A = Spools 0, 1, 1/2, 8 50 60
B = Spools 0/2, 3, 6, 7
C = Spools 4, 5, 58, 16, 17
D = Spools 2/2 0 0
0 8 16 24 32 40 0 12 24 36 48 60
Flow rate [l/min] Flow rate [l/min]
 7 DIMENSIONS [mm]

ISO 4401: 2005

Mounting surface: 4401-03-02-0-05
Fastening bolts:
DHE: 4 socket head screws M5x30 class 12.9
DHO: 4 socket head screws M5x50 class 12.9
Tightening torque = 8 Nm
Seals: 4 OR 108 P = PRESSURE PORT
Ports P,A,B,T: = 7.5 mm (max). A, B = USE PORT
T = TANK PORT
Overall dimensions refer to valves with connectors type 666 For the max pressures on ports, see section 

DHE-06 DHE-07

Option /WP

Mass: 1,75 kg Mass: 2 kg

DHO-06 DHO-07

Mass: 1,9 kg Mass: 2,6 kg

8 MOUNTING SUBPLATES

Counterbore
GAS Ports Mass
Model Ports location [mm]
A-B-P-T [kg]
A-B-P-T

BA-202 Ports A, B, P, T underneath; 3/8" 1,2

BA-204 Ports P, T underneath; ports A, B on lateral side 3/8" 25,5 1,8

BA-302 Ports A, B, P, T underneath 1/2" 30 1,8

The subplates are supplied with 4 fastening bolts M5x50. Also available are multi-station subplates and modular subplates. For further details see table K280.

03/13