MAINTENANCE

TECHNICAL AEROSOLS
for maintenance

Equipment lifetime optimization

Lubricating solutions

Innovative green-based technologies

MOLYDAL DESIGN NEW LUBRICATION TECHNOLOGIES

 Molydal offers a full range of high-tech
industrial lubricants and maintenance
products. Molydal is the leader in offering
cost-savings solutions to maintenance
and production managers thanks to
our wide range of lubricants coupled
with outstanding lubricating systems.

SERVICE :
We offer a complete service in lubricating solutions (greasing equipment,
tailor-made products, lubricant recommendation,technical assistance).
Our qualified team support you to ensure that you optimize your
productivity and increase profitability.

Laboratory :
Research and Development Laboratory.
Formulation to customers specification.
Quality control.

Problem-solver and cost-saving partner :

Tailor-made solution.
Wide range of products for all industries, from process oils
and greases to maintenance aerosols.

DISTRIBUTION :
National and European network.
Over 100 retailers in France and abroad

Innovation :
Green based lubricants for VOC and health issues
Technical accuracy thanks to greasing systems
solution (for oil and grease)
 TABLE OF CONTENTS
GREASES & PASTES...............................................page 4
GRIPCOTT NF
LCH250
MULTI TP
DEGREASERS..........................................................page 5
KL BIO
CONTACTOL DTZ
STARNET
DEWATERING AGENTS ......................................... page 6-7
TOP 5
DEGRIPPANT ALIMENTAIRE
REMFOR V7+
V7 BIO
DEGRIPPANT MOS 2
DEGRIPPANT NF NUCLEAIRE
WORKSHOP AEROSOLS ....................................... page 8-9
AIRBUL NF
AMBRINE AIR ALIMENTAIRE
DECAPANT 90
BELTONN
SMOS
METALWORKING FLUIDS....................................... pages 10
STAREX
TEREBOR
RUST PREVENTATIVES ......................................... page 11
TOP 5
DRY PROTEC
PROTEC 800
GALVANISATION......................................................page 12
GALVASUN
ZEDENCOTT
VARNISH...................................................................page 13
ADERMOS 850
EXTILUB
WELDING ANTI-SPATTER ...................................... page 14
ADS 14
BUSENET 750
NB 25 DTZ
SILICONE FLUIDS....................................................page 15
SILICONES
SILICONES AL
SIL 172 AL
PLASTIC INJECTION MOULDING.......................... pages 16-17
DEMOPLAST
DEMOLUB
DEMOPAST 740
REMFOR
PERF 80
CHAIN LUBRICANTS............................................... page 18
FILLMORE AL
NS 20
NS 250
GLUES AND SEALANTS......................................... page 19
ET 430
BLACK SEAL
AN420
GREASES & PASTES

GRIPCOTT NF
CHARACTERISTICS
Zinc and Copper micronized mixture suspended in a grease base. Color : Silver.

USES
Mounting of bolt and nut assemblies submitted to severe conditions to allow easy dismantling, cylinder head
gaskets, steam joints, and various assemblies and mechanical parts working at high temperatures. Protection,
mounting and lubrication at high temperatures, or in severe chemical or atmospheric surroundings.

PACKAGING
GRNFA2 GRNFTB GRNFB1 GRNF50
Aerosol 650 ml x 12 Tube 140 gr x 12 Box 1 kg x 6 Drum 50 kg x 6

LCH 250
CHARACTERISTICS
Extreme pressure adhesive grease. Lithium Complex Grease with outstanding resistance properties at work and under high
temperatures. Reinforced adhesiveness properties and the used thickener gives to LCH 250 an excellent resistance to humid and
aggressive surroundings This range of greases has outstanding anti-corrosion properties to secure a good protection of materials.

USES
For all types of bearings, gearings or mechanism submitted to severe conditions of use and to high temperatures.

PACKAGING
LCH25050 LCH2505L LCH250B1 LCH250CA LCH250FT
Drum 50 kg Drum 5 L x 2 Box 1 kg x 6 Canister 400 gr x 24 Barrel 180 L

MULTI TP
CHARACTERISTICS
High performance and multi purpose grease. The thickener gives to MULTI TP a good mechanical stability
at work and during storage. The product has extreme pressure additives to reduce wear under high
load and to give protection against corrosion for all type of materials. MULTI TP is adhesive on all metals.
Offers good resistance to water.

USES
For all type of bearings, joints, pins, swivels, racks, agricultural machinery, cement plants, brickyards, sugar factories,
quarries, mines, road transport. This product is also called MULTI PURPOSE.

PACKAGING
MULTI50 MULTI5L MULTIB1 MULTICA MULTIFT
Drum 50 kg Drum 5 L x 2 Box 1 kg x 6 Canister 400 gr x 24 Barrel 180 L

4
DEGREASERS

KL BIO
CHARACTERISTICS
V.O.C Free and biodegradable. 100% renewable raw materials. Dramatic degreasing properties. For heavy
duty or sensitive environments.

USES
Emulsifiable degreasing agent developed to replace petroleum-based solvents. KL BIO is ready to use and can
be rinsed with water may be recycled at ambient temperature. KL BIO is applied with a cloth, poured or sprayed
or the object immersed in it.
PACKAGING
KLBIOA2 KLBIO5L KLBIO30 KLBIOFT
Aerosol 650 ml x 12 Drum 5 L x 2 Keg 30 L Drum 200 L

CONTACTOL DTZ
CHARACTERISTICS
De-Oxidizing Cleaner non-flammable for electrical and electronic contact. A substitution solvent for CFCs, chlorinated solvents and
brominated solvents in many application fields thanks to its almost instantaneous evaporation rate.

USES
Cleaning and rinsing agent for all electrical or electronic mechanisms such as HiFis or telephone gear, coils, relays, printed circuits,
radar equipment, counters, etc.

PACKAGING
CONTADTZA2
Aerosol 650 ml x 12

STARNET
CHARACTERISTICS
Cold aerosol degreaser for industrail usage. STARNET grease remover is guaranteed not to contain chlorinated
solvents, HCFCs or glycol ether and is a non-greasy cold degreaser with very high solvent power. STARNET is inert
with respect to rubbers and most plastics. However, compatibility can vary with the applications conditions.
Therefore, it is recommended to verify before using.

USES
STARNET is perfectly suitable for all degreasing operations on all kinds of mechanical parts where a fast
evaporation rate is desired.

PACKAGING
STARNETA2
Aerosol 650 ml x 12

5
DEWATERING AGENTS

TOP 5 - 5 Functions
CHARACTERISTICS
Lubricant Release agent, anticorrosion protection, waterproofing agent de-oxidizing and de-watering agent. Low
surface tension allowing better penetration to lubricate and protect normally unreachable parts of mechanisms.
Multi-purpose fluid.

USES
Inter-process protection of machined parts. Protection of moulds and tools in foundries, glass works, extrusion,
cutting, plastic injection. Protection of shotguns, door hinges lubrication of locks.

PACKAGING
TOP5A2
Aerosol 650 ml x 12

DEGRIPPANT ALIMENTAIRE
CHARACTERISTICS
Lubricating-penetrating agent having a very low superficial tension. The Food Grade Releasing Agent is free from silicone,
can be used on all metals and is inert towards most elastomer and plastics. Its components allow to proceed to a quick
releasing of through oxidation, seized parts: Bolt-and-nut works, screwed assemblies, iron-works, slides, jack-rods

USES
Reconditioning of all clamped parts. Maintenance, cleaning of all mechanisms. Lubrication: cutting, punching and
small deformation on steels and alloys.Does not soil the parts.
PACKAGING
DGTALA2
Aerosol 650 ml x 12

REMFOR V7 +
CHARACTERISTICS
Lubricating-release agent having a very low superficial tension. Its components allow to proceed to a quick releasing of
through oxidation, seized parts: Bolt-and-nut works, screwed assemblies, iron-works, slides, jack-rods Anti-rust,
anti-corrosion, quick working, avoids the cold drawing of the threads.

USES
Reconditioning of all clamped parts. Maintenance, cleaning of all mechanisms. Lubrication : cutting, punching and
small deformation on steels and alloys. Tapping, boring. Does not soil the parts. Compatible with most of elastomeres
and does not attack the paints.

PACKAGING
REV75L REV7A1 REV7A3 REV7FT
Drum 5 L x 2 Aerosol 520 ml x 12 Aerosol 800 ml x 12 Barrel 200 L

6
DEWATERING AGENTS

V7 BIO
CHARACTERISTICS
V7 BIO is a biodegradable rust remover and lubricant with low surface tension, biodegradable V.O.C Free. Its ingredients
contribute to the rapid release of rusted-in parts: nuts and bolts, screwed assemblies, lock assemblies, slides, jack rods, etc.

USES
For the restoration of all blocked parts. The maintenance and cleaning of all types of mechanism. Lubrication:
Cutting, stamping and slight reworking of steel and alloys.Tapping and drilling. Does not stain parts. Compatible
with the majority of elastomers and does not attack paint.

PACKAGING
KLBIOA2 KLBIO5L KLBIO30 KLBIOFT
Aerosol 650 ml x 12 Drum 5 L x 2 Keg 30 L Drum 200 L

DEGRIPPANT MOS 2
CHARACTERISTICS
DEGRIPPANT MOS 2 has a very high power of penetration allowing a very quick action on all metallic parts having
been submitted to oxidation or corrosion (bolts, dudgeons, iron works, coach-buildings, slides). Its components
combined with Molybdenum disulphide make of this DEGRIPPANT a releasing agent of unequalled quality : the
plating realised with MOS2 avoids a further seizing.

USES
Releasing, lubrication, maintenance and cleaning of all mechanisms. Tapping of the metals.

PACKAGING
DGTA3 DGT5L DGTFT
Aerosol 800 ml x 12 Drum 5 L x 2 Barrel 200 L

DEGRIPPANT NF NUCLEAIRE
CHARACTERISTICS
This food-grade penetrating fluid is also a lubricant, offering very low surface tension. Its compounds allow it to
quickly released through oxidization seized parts. Aspect : Very fluid liquid. Colour : Amber coloured.
USES
Releasing of screw assemblies submitted to atmospheric oxidation and to chemical corrosion. Collector flanges, ex-
haust pipes. Releasing of sluice-rods, shrinking. Lubrication of chains in aggressive surroundings, of locks, hinges,
joints Compatible with non ferrous metals.

PACKAGING
DGNUA2 DGNU5L DGNUB1
Aerosol 650 ml x 12 Drum 5 L Drum 1 L x12

7
WORKSHOP AEROSOLS

AIRBUL NF
GAS LEAK DETECTOR

CHARACTERISTICS
An universal gas leak detector. Enables all pressurised air or gas leaks to
be detected, no matter how small. This fluid has a foaming reaction and
contains a corrosion inhibitor which eliminates any risk of corrosion.

USES
For checking the sealing of all pipes, tanks, valves, stopcocks,
connections... Essential in any company using pressurised air or gas.

PACKAGING
AIRBULNFA2 : Aerosol 650 ml x 12
AIRBULNFA2 : Aerosol 650 ml x 12
AIRBUL5L : Drum 5 L x 2

AMBRINE AIR ALIMENTAIRE

CHARACTERISTICS
Special oil to lubricate the air used to operate pneumatic tools, pumps and compressed air equipment.
AMBRINE AIR alimentaire provides better efficiency in mechanisms, prevents binding and sticking of equipment and assures
an effective and durable lubrication. Non Compounds Program Listed H1 Registration : 126640.

USES
Lubrication of all air circuits in order to assure the lubrication and protection of pneumatic tools, pumps and compressed air
equipment in all environments (humid, dusty, corrosive or hot).

PACKAGING
AMBRB1 AMBR5L
Drum 1 L x 12 Drum 5 L x 12

8
WORKSHOP AEROSOLS

DECAPANT 90 - Universal remover in aerosol

CHARACTERISTICS
Stripper particularly reactive. It has proven performance for fast stripping of inks, paints and varnishes and cleaning the mold
cavities. It can also be used to easily remove adhesives, oils and hardened fats, carbon deposits, joint planes or metal surfaces.

USES
Effective on most surfaces such as wood, metal, glass, tile or stone. Removal of silicone gaskets on covers, on double-
glazed windows, graffiti. Cleaning the mold cavities.

PACKAGING
DECAP90A2
Aerosol 650 ml x 12

BELTONN
CHARACTERISTICS
Belt adhesive, developed to increase adhesiveness and eliminate the slipping of flexible transmission equipment. Avoids
any premature wear and loss of power due inopportune slipping. Is not corrosive towards leather, plastics, rubber or textiles.
USES
Usable on all belts in order to avoid slipping either as a preventive agent, or in case of emergency for a quick
troubleshooting. Allows not to exaggeratedly tighten the belt and thus increase their life time.

PACKAGING
BELTA2
Aerosol 650 ml x 12

SMOS
CHARACTERISTICS
High performance and multi purpose grease. The thickener gives to MULTI TP a good mechanical stability
at work and during storage. The product has extreme pressure additives to reduce wear under high
load and to give protection against corrosion for all type of materials. MULTI TP is adhesive on all metals.
Offers good resistance to water.
USES
For all type of bearings, joints, pins, swivels, racks, agricultural machinery, cement plants, brickyards, sugar factories,
quarries, mines, road transport. This product is also called MULTI PURPOSE.

PACKAGING
SMOSA2
Aerosol 650 ml x 12

9
METALWORKING FLUIDS

STAREX
ANTI CORROSION PRODUCT - FILM

CHARACTERISTICS
Special oil, intended for drilling, tapping and reaming operations as
manual contribution. Its useful packaging in aerosol form allows the
user a precise and punctual application.
STAREX extreme pressure grade is to be used on all steels as
well as on aluminium and copper alloys.

USES
STAREX is easy to degrease on light and copper alloys.
It is recommended to degrease quickly in order to avoid the risks
of superficial stains when the visual aspect is important.

PACKAGING
STARA2
Aerosol 650 ml x 12

TEREBOR
CHARACTERISTICS
High extreme pressure characteristics which assure a perfect cut and significantly reduce tool wear since the thread is continually
lubricated and cooled. Its high cooling power allows increasing the cutting speeds very much ; its low viscosity and good wetting
power assure a quick rise in the formed chip, reducing the risks of pull-out, tool scoring and metallization..

USES
To make a thread in high strength, extra hard, heat and refractory, and stainless steels, remove small diameter chips, recessed holes,
metals with a low machining index on automatic or semi-automatic machines.
PACKAGING
TEREFL TERE5K TERE30
Bottle 125 ml x 12 Drum 5 L x 2 Drum 30 L

10
RUST PREVENTATIVES

PROTEC 800
CHARACTERISTICS
Oily film free from solvent and or silicone. The formulation of PROTEC 800 offers efficient outdoor or indoor protection of
metals against corrosion although it can be easily removed by usual solvents or alkali detergents.

USES
Protection of steel tubes after rolling. Protection of fe-metals raw or machined. Protection of tools, injection moulds, inter-
mediate storage.

PACKAGING
PRO800FT
Barrel 200 L

DRY PROTEC
ANTI CORROSION PRODUCT - FILM

CHARACTERISTICS
Formulated for exterior or interior protection from all types of metal
parts and production equipment. After evaporation of the solvent, it
leaves a film on parts waxy fine, dry to the touch, with a high resis-
tance to moisture. DRY PROTEC has an effect water repellent to
hunt water droplets that can form due to condensation.
Specially formulated not to run and avoid clogging dirt and molds to
the first workstation.
DRY PROTEC protects your items during transit or during storage for
several months.

USES
Protection of steel pipes after rolling, ferrous machined or as cast,
all kinds of tools, injection molds, storage inter machining.

PACKAGING
DRYPROTECA2 : Aerosol 650 ml x 12

11
GALVANISATION

ZEDENCOTT
CHARACTERISTICS
Coating rich in zinc allowing a long life anti corrosion protection of ferrous metals. This kind of coating extends the
now conventional protection of ferrous metals with zinc : hot galvanization, zinc metallisation, electrolytic process. The
protection remains even if an accidental breaking in the continuity of the coating happens.

USES
On all ferrous metals where water, dampness, aggressive atmosphere, cause corrosion. All metallic frames, pipe and tube
assembling, sluices, bolt and nut works, tanks Retouching of iron works, damaged galvanized parts.Treatment of rust
beginnings, cutting edges of the metals. Motor-car industry, marine, public works, transports, chemistry...
PACKAGING
ZEDA2
Aerosol 650 ml x 12

GALVASUN
BRIGHT GALVANIZING

CHARACTERISTICS
Long lasting galvanizing coating for all metals.
GALVASUN has a good behaviour against aggressive surroun-
ding.

USES
For the protection of metals against corrosion. Retouching of iron-
works, damaged galvanized parts. Protection of the cutting edges
of the metals. Protection of screw assembling on galvanized steels.

PACKAGING
GALVASUNA2
Aerosol 650 ml x 12

12
VARNISH

ADERMOS 850
SLIDING VARNISH

CHARACTERISTICS
Cold polymemerizable sliding varnish. Service temperature : - 180 C
to 450C. Excellent adherence to all media. Good anticorrosion
protection. Resistant to oils, greases and other chemical pro-
ducts. Excellent friction properties.

USES
Shake vigorously the aerosol before use. Pressurized recipient :
to be protected against sunlight and not to be exposed to tempera-
tures above 50C. Do not pierce or burn even after usage.

PACKAGING
ADER850A1
Aerosol 520 ml x 12

EXTILUB
CHARACTERISTICS
EXTILUB is at once a dry lubricant and a mould removing agent. As a dry lubricant, it was especially designed
for low moving speeds and middle loads. As a mould removing agent, it is an excellent anti-adhesive agent for all
materials. The phosphatation allows a better hanging of the film.

USES
By lubricating : dry lubricant agent for wood, metals, paper, glass, rubber... Protection of tanks, cables, offset cylinders,
joints in chemical, aggressive or corrosive surroundings. Lubrication in abrasive atmospheres. In mould removing :
excellent agent for plastic materials, stratified materials.
PACKAGING
EXTIA2
Aerosol 650 ml x 12

13
WELDING ANTI-SPATTER

ADS 14
CHARACTERISTICS
Anti-adhesive agent without, used only to welding nozzles but also to all pieces in the neighbourhood
of the parts to be welded. ADS 14 is formulated on a water base and it is free from silicone and metal
particles.
USES
ADS 14 prevent the sticking of metallic particles during melting. It doesnt stain parts. In addition, it is
easy to clean with water or solvent based grease removers. In all welding industries : Sheet metal work,
plumbing, vessel manufacture
PACKAGING
ADS14A2 ADS1430 ADS14FT
Aerosol 520 ml x 12 Keg 30 L Barrel 200 L

BUSENET 750
CHARACTERISTICS
Anti-adhesive agent for the protection of parts and welding nozzles in automatic or half-automatic welding.
Guaranteed free from any metallic charges, silicones, graphite and copper. BUSENET 750 does not stain or cause corrosion
and is easily removed with degreaser usually used and is specially formulated to limit odour problems and smoke emanation.

USES
BUSENET 750 can be used on all surfaces (steel, alloy...) and it doesnt oxide parts. Welding nozzles and parts to be
welded. Protection against spatter.
PACKAGING
BUSE750A1
Aerosol 520 ml x 12

NB 25 DTZ
CHARACTERISTICS
Boron nitride varnish applied as an aerosol to protect surfaces up to 1000C by depositing a dry film. NB 25 DTZ has a
good adherence on all media and contains no silicone or chlorinated solvents.

USES
It is used to protect not only welding tips, but also all types of parts subjected to high temperatures. Welding anti-adhesive.
Protection of parts or tools. Mold removal agent for glass works.

PACKAGING
NB25DTZA1
Aerosol 520 ml x 12

14
SILICONE FLUIDS

SILICONES AL
CHARACTERISTICS
For food-processing industry : Lubrication of bearings and gears subject to small loads.
USES
Lubrication of precision equipment in laboratory. Lubrication of shears, greasing chains subject to low loads.
Clean lubrication of all unloaded mechanisms, and for friction involving metal & plastic and plastic & plastic.
It can also be used as a mould releasing agent. Lubrication, waterproofing, mould releasing, anti-static protection
in the food-processing industry.

PACKAGING
SILALA2
Aerosol 650 ml x 12

SILICONES
CHARACTERISTICS
All-purpose silicones. The silicones used in the formulation were selected to offer multipurpose properties allowing
a very wide use : waterproofing lubrication, mould release, anti-static protection and rust prevention. SILICONE
can secure the lubrication without important modification of the viscosity at high and low temperatures.

USES
To also use as a mould releasing agent for rubber and plastic materials. Lubrication of precision equipment in laboratory
and clock industry. Lubrication of guillotines in the cardboard industry.Greasing of looms.

PACKAGING
SILIA1 SILIA3
Aerosol 520 ml x 12 Aerosol 800 ml x 12

SIL 172 AL
CHARACTERISTICS
Silicone oil for lubricationa and mold removal usable in contact by chance with foods. Highly lubricating and
antistatic silicone oil with added solvent usable in a wide range of applications. SIL 172 AL is a clean and water
repellent lubricant and behaves well with aggressive chemical agents. H1 Registration No. : 129 605.

USES
For all mold removal operations involving rubbers and plastics. For the lubrication of cutter blades, paper manufacturing
cylinders, print shop and plastic industry. For the lubrication of fritted metals, timers, watches, office machines, computers, etc.
For the repair of boots and firearms and the protection of locks against freezing conditions.

PACKAGING
SIL172ALA2 SIL172AL30
Aerosol 650 ml x 12 Drum 30 L

15
PLASTIC INJECTION
MOULDING

DEMOPLAST
CHARACTERISTICS
Anti-adhesion and mould release agent free of silicon, chlorinated solvents and HCFC.
Used to remove plastics from moulds (thermoplastics, thermohardening plastics) and rubber.

USES
Mould release fluid for operations with cold or hot moulds. Droplet spray.

PACKAGING
DEMECO2A2 DEMO740NA2
Aerosol 650 ml x12 Aerosol 650 ml x 12

DEMOLUB
CHARACTERISTICS
Anti-adhesion and mould release agent , chlorinated solvents and HCFC.
Used to remove plastics from moulds (thermoplastics, thermohardening plastics) and rubber.

USES
Mould release fluid for operations with cold or hot moulds. Very fine spray.

PACKAGING
DEMOLUBA1
Aerosol 520 ml x 12

DEMOPLAST 740
CHARACTERISTICS
Anti-adherent agent and a stripper guaranteed without chlorinated solvents or HCFCs. Its used to strip plastic
materials (thermoplastics, thermohardening plastics) and rubbers.
DEMOPLAST 740 is a stripper liquid for operations on hot or cold molds. It doesnt leave residues or stain parts
and is applicable on nonporous substrates.

USES
Formulated on the basis of paintable silicone oils, allows all subsequent coating operations : impregnation, pain-
ting, screen printing, gluing, welding, electrodeposition

PACKAGING
DEMECO2A2
Aerosol 650 ml x12

16
PLASTIC INJECTION
MOULDING

REMFOR
CHARACTERISTICS
Lubricating, penetrating agent having a very low superficial tension. Its components allow to proceed to a quick re-
leasing of through oxidation, seized parts: Bolt-and-nut works, screwed assembling, iron-works, slides, jack-rods
Anti-rust, anti-corrosion, quick working, avoids the cold drawing of the threads.

USES
Reconditioning of all clamped parts. Maintenance, cleaning of all mechanisms. Lubrication : cutting, punching and
small deformation on steels and alloys. Tapping, boring. Does not soil the parts.
PACKAGING
REMFA2
Aerosol 650 ml x 12

PERF 80
CHARACTERISTICS
Fluorinated oil intended for long-term lubrication at very low or
very high temperatures, as well as for chemical environments
that are particularly severe (no approval for the aerosol).

USES
Lubrication for bottling lines, equipment at canneries, abattoirs,
biscuit factories, chocolate factories, dairies ...

PACKAGING
PERF80A2
Aerosol 650 ml x 12

17
CHAIN LUBRICANTS

FILLMORE AL
CHARACTERISTICS
Synthetic lubricant with a foamy aspect specially designed for chain lubrication under severe conditions.
FILMORE AL has an outstanding adhesiveness and shows excellent resistance to water washout with no
throw qualities at low or high speed. H1 Registration No. : 142 222.

USES
Lubrication of chains and conveyors used during production or packing of food or pharmaceutical products.Sterilization,
bottling, fermentation lines, oven chain. For all type of high speed running mechanism or gear .
PACKAGING
FILLALA2
Aerosol 650 ml x 12

NS 20
CHARACTERISTICS
Oily and very adhesive chain lubricant with good wear resistance qualities, its adhesiveness allow resistance to water and steam,
and avoid centrifugation at high operating speeds. Resistant to oxidising environments.

USES
In the industries : automotive (floor conveyor, transfer chain), sugar refining (transmission chains and reception center
lines), food (sterilization lines), preserves (bottling lines), wood (wood particle transport, glass (broken glass transport),
lubrication of jack shafts and slide bars.
PACKAGING
NS20A2 NS2030
Aerosol 650 ml x 12 Keg 30 L

NS 250
CHARACTERISTICS
Outstanding chain lubricant used to lubricate the chains under extreme temperature conditions and in dusty
environment. The nature of its basic oils reinforced by antioxidizing additives, confers excellent lubricating
properties. NS 250 has adhesive qualities which prevent splashing or centrifuging.

USES
Lubrication by dipping, brush, drop by drop or spraying. Lubrication of conveyor, dipper, paint oven or screen printing
chains. Lubrication of transmission chains in the tapestry and dyeing industry.

PACKAGING
NS250A2 NS2505L
Aerosol 650 ml x 12 Drum 5 L x 2

18
GLUES AND SEALANTS

ET 430
CHARACTERISTICS
BRINELL ET 430 is a sealing and tightening mono-compound resin, hardening under anaerobic condition, in contact
with metals or by temperature increase. Product has an high moistening power. During hardening process no increase or
decrease of volume can be observed. Offers excellent anti-corrosion protection on metals.
USES
BRINELL ET 430 i used for extreme tightness of threading and complies with specification of NF EN 751-1, for tightness
material for pipe fittings in contact with gas groups 1, 2 and 3 and for hot water.
PACKAGING
ET430075
75 ml bottle x 6

BLACK SEAL
CHARACTERISTICS
BLACK SEAL is a black silicone seal for sticking and tightness to be used on all materials.

USES
Resistant to oil, grease and solvent. Very high flexibility, vibration resistant.. Can be used as a cord or as a thin coating.
For sticking and tightness of control boxes. Card box tightness. Ready for use

PACKAGING
BLACKSEAL
Aerosol 200 ml x 12

AN 320
CHARACTERISTICS
BRINELL AN 320 is a sealing and tightening resin, without solvent, monocomponent, hardening in the absence of air,
when in contact with metals or by increasing the temperature.Very absorptive product. No increase or reduction in volume
during hardening.Excellent anticorrosion effect on metals.

USES
Average locking and sealing of axes, screws, studs, ball bearings. Effective on all threaded metal elements.

PACKAGING
AN32050
50 ml bottle x 6

19
 Non-exhaustive liste of product
You can find our range of products
www.molydal.com
Votre distributeur

Edition Fvrier 2013

MOLYDAL SA - ZAET 221 rue Paul Langevin 60744 SAINT MAXIMIN

Phone : +33 3 44 61 76 76 - Fax : +33 3 44 25 17 78

20 20