Section 4: Chemical Calculations

Topic Page Numbers

Relative Atomic Mass 2

Relative Molecular Mass 4

Calculating the Formula of Simple Compounds 7

Calculating the Mass of Products/Reactants from an Equation 11 - 12

Percentage Yield 18

Atom Economy 23-24

Comparing Atom Economy for Methods of Titanium Extraction 27-28

BY THE END OF THIS TOPIC YOU SHOULD BE ABLE TO:

Describe relative atomic mass (Ar) and know that

different elements have different masses
Calculate the relative molecular (formula) mass (M r) of
a compound by using its formula
Calculate the formula of a simple compound from given
data
Be able to calculate reacting masses of reactants or
products using a balanced symbol equation
Describe and calculate the percentage yield of a
reaction
Calculate the atom economy of a reaction from a given
equation
Assess and compare the level of waste in chemical
reactions using atom economy

1
 Relative Atomic Mass

Different elements have different numbers of protons,

neutrons and electrons.

The mass of an element comes from the neutrons and protons

in its nucleus (an electrons mass is negligible).

The relative atomic mass is the largest number in the

elements box on the periodic table.

It is usually at the top of the box.

It is often written as Ar.

It tells us how heavy an element is compared to other

elements.

Because it is a way of comparing elements it doesnt have

any units.

2
Relative Atomic Mass Questions

Question 1:

Write down the Ar for the following elements:

Osmium Lithium
Sodium Nitrogen
Platinum Helium
Titanium Carbon
Chlorine Hydrogen
Argon Sulphur

Question 2:

Circle the element that is heavier:

a) Carbon / Oxygen
b) Sodium / Lithium
c) Gold / Copper
d) Hydrogen / Helium
e) Lead / Tin

Question 3:

Write down the elements with the following Ar values:

Ar Element

12

16

23

222

3
 Relative Molecular Mass

The relative molecular mass can be worked out by

adding up the relative atomic masses of the
elements in the molecule.

It can also be written as Mr or relative formula

mass

Example 1: Calculating the relative molecular mass of CH 4

CH4 contains 1 x C and 4 x H atoms (remember the small

number applies to the H only)

Ar for C = 12
Ar for H = 1

So Mr = (1 x 12) + (4 x1)
= 16

Calculate the Mr of the following substances:

(the first 2 have been done for you)

(a)H2O = 1 + 1 + 16 (b) CO2 = 12 + 16 + 16 (c) NaCl =

= 18 = 44
(d) O2 = (e) H2 = (f) HCl =

(g) NaOH = (h) KOH = (i) MgO =

(j) CO = (k) C2H4 = (l) C2H6 =

(m)CH4 = (n) C4H10 = (o) C5H12 =

(p) C6H6 = (q) S8 = (r) Al2O3 =

4
 Example 2: Calculating the relative molecular mass of Al(OH) 3

Al(OH)3 contains 1 x Al, 3 x O and 3 x H (remember the small

number applies to everything inside the bracket)

Ar for Al = 27
Ar for O = 16
Ar for H = 1

So Mr = (1 x 27) + (3 x 16) + (3 x 1)
= 78
.

Now try these examples the first one has been done for you.
(a)Ca(OH)2 = 40 + (16 + 1)2 = 74 (b) (NH4)2SO4 =

(b) (NH4)2Cr2O7 = (d) Fe(OH)2 =

(e) Fe(OH)3 = (f) (NH4)2S203 =

(g) (NH4)3PO4 = (h) C6H2CH3(NO2)3 =

5
Fill in this worksheet

6
 Calculating the Formula of Simple Compounds
You can use relative atomic masses (Ar) to calculate the
formula of compounds when you know the mass of reactants
you used.

Example:
3.2g of sulphur reacts with oxygen to produce 6.4g of sulphur
oxide. What is the formula of the oxide?

Step 1 Write down the masses of reactants:

S = 3.2g O = 6.4 - 3.2 = 3.2g

Step 2 Divide Masses by Ar

3.2 = 0.1 3.2 = 0.2

32 16

Step 3 Divide everything by the smallest number to get the

ratio

0.1 = 1 0.2 = 2
0.1 0.1
Ratio S : O = 1:2
Use this table as a
Step 4 - Write out the formula prompt until you are
confident with the
method.
SO2

Step Process
1 Write down masses of reactants* * If you are
2 Divide by Ar given % just
3 Divide by smallest number to get ratio use the % as
4 Write down formula the mass in
grams.

7
Answer these questions to calculate the formula of simple
compounds:

1. 10.2g of an oxide of aluminium contains 5.4g of aluminium.

Calculate the formula of the oxide (i.e. empirical formula)

2. A compound contains 29.11% sodium, 40.51% sulphur and

30.38% oxygen by mass. Calculate its simplest formula
(empirical formula)

3. 14.2g of a compound that contains 3 elements (sodium,

sulphur and oxygen). The mass of sodium is 4.6g and
sulphur is 3.2g of sulphur. The rest is oxygen. Calculate
the mass of oxygen, and then calculate the simplest
formula of the compound.

8
4. A compound contains 40.21% of potassium, 26.80%
chromium and 32.99% oxygen by mass. Calculate its
empirical formula

5. A sample of a compound containing 3 elements (potassium,

chromium, oxygen) weighs 22.62g. This amount contains
6g of potassium and 8g of chromium and the rest is
oxygen. Calculate the mass of oxygen and then calculate
the simplest formula (empirical formula)

9
 Calculating the Mass of Products from a
Reaction Equation

You can use the reaction equation and information about

relative atomic mass to calculate the mass of products you
would expect to get.

Example
N2 + 3H2 2NH3
If we have 7g of N2, how much NH3 can we make?

Step 1
Write down the Mr or Ar underneath each chemical and multiply
by any balancing number

N2 + 3H2 2NH3
28 3x2 = 6 2x17 = 34

This means that for every 28g of N2 we would expect to get

34g of NH3.

Step 2
Decide what fraction or multiple of the Mr the reacting amount
is:
By examination 7 is 28/4

Step 3
Work out how much product you would get

34 / 4 = 8.5g

Excess means you have more than enough of that reactant so it

wont affect your calculation

10
 Calculating the Mass of Reactants from a
Reaction Equation

The previous method can also be used to work out the mass of
reactants used in a chemical reaction.

Example
The reaction between iron (Fe) and sulphur (S) to make iron
(II) sulphide (FeS).
Fe + S FeS

How much Fe is needed to make 176g of FeS?

Step 1
Write down the Mr or Ar underneath each chemical and multiply
by any balancing number

Fe + S FeS
56 32 88

This means that for every 88g of FeS made, we need 56g of Fe
and 32g of S

Step 2
Decide what fraction or multiple of the Mr the reacting amount
is:
By examination: 176 is 2 x 88

Step 3
Work out how much reactant you would need

56 x 2 = 112g

Q. How much S would be needed to make 176g of FeS?

11
Now try these questions yourself. Remember to start by writing the M r
or Ar under each formula in the equation, and multiplying by the
balancing number.
5.6g of iron react with excess sulphur to make WHAT MASS of
iron(II) sulphide?
Fe + S FeS

3.65g of HCl react with excess sodium hydroxide. What mass of water
is formed?
HCl + NaOH NaCl + H2O

8g of hydrogen are exploded in excess oxygen. What mass of water is

formed?
2H2 + O2 2H2O

If 3.2 g of oxygen is reacted with excess hydrogen, what mass of water

is formed?
2H2 + O2 2H2O

12
What mass of hydrogen and oxygen are needed to make exactly 3.6g of
water (2 answers needed)
2H2 + O2 2H2O

When sulphur (found in coal) burns it forms acid rain. What mass of
sulphur dioxide is formed from 32 tonnes of sulphur and excess
oxygen?
S + O2 SO2

When a hydrocarbon burns in excess oxygen, 2 products are formed

(water and carbon dioxide). What mass of the greenhouse gas (CO 2)
forms when 10g of heptane (C7H16), found in petrol, are burned in
excess O2?
C7H16 + 11O2 7CO2 + 8H2O

13
 Extension Questions
Try these questions

123g of sulphur are burned in excess oxygen. What mass of sulphur

dioxide forms?
S + O2 SO2

29 tonnes of iron (III) oxide are reacted in the blast furnace with
excess carbon monoxide. What mass of iron is produced?
Fe2O3 + 3CO 2Fe + 3CO 2

14
2.567g of pure sodium hydroxide are reacted with excess dilute
sulphuric acid. What mass of water is formed?
2NaOH + H2SO4 Na2SO4 + 2H2O

What mass of lead nitrate has to be thermally decomposed to give 50g

of lead oxide?
2Pb(NO3)2 2PbO + 4NO2 + O2

15
What mass of water is formed when 1kg (1000g) of octane (equivalent
to just over a litre of petrol) is burned in excess oxygen?
2 C8H18 + 25 O2 16 CO2 + 18 H2O

What mass of carbon dioxide is formed on a typical 25 mile car

journey? (Assume the petrol consists of 2kg {2000g} of pure heptane
and that half a gallon of it [2.25 litres] reacts with excess oxygen in
the air).
C7H16 + 11 O2 7 CO2 + 8 H 2O

16
 Percentage Yield

In most chemical reactions you do not get the maximum

expected amount of product. This can be to do with the
chemistry of the reaction or the way the experiment took
place.

Example

Fe + S FeS

56 g of iron reacts to give 80 g of iron sulphide

Step 1:
Calculate the theoretical yield (the maximum amount of
product we could expect) in the same way you did before.

Fe + S FeS
56 32 88

So 56g of iron should give us 88 g of iron sulphide.

Step 2:
Calculate the percentage yield:

= 80 x 100 = 90%
88

17
Look at your answers to the theoretical yield questions a few pages
back and answer these related questions
3.65g of HCl react with excess sodium hydroxide. What is the % yield
if 1.5g of water is formed?
HCl + NaOH NaCl + H2O

3.65 1.5

8g of hydrogen are exploded in excess oxygen. What is the % yield if

only 65g of water is formed?
2H2 + O2 2H2O

18
If 3.2 g of oxygen is reacted with excess hydrogen to give 3.2g of
water. What is the theoretical yield?
2H2 + O2 2H2O

When sulphur (found in coal) burns it forms acid rain. What is the
theoretical yield when 32 tonnes of sulphur are burned to give 63
tonnes of sulphur dioxide?
S + O2 SO2

19
When a hydrocarbon burns in excess oxygen, 2 products are formed
(water and carbon dioxide). What is the percentage yield when 10g of
heptane, found in petrol, is burned in excess O2 to give 25g of the
greenhouse gas (CO2)?
C7H16 + 11O2 7CO2 + 8H2O

1 tonne of nitrogen is reacted with excess hydrogen to give 0.25 tonnes

of ammonia (NH3). What is the percentage conversion?
N2 + 3H2 2NH3

20
Try this typical GCSE question

21
 Atom Economy

This is a measure of how successful a reaction has been

in converting raw materials into a useful product.

It looks similar to percentage yield, but its not the

same thing.

If most of what you produce in a reaction is the desired

product then there will, by definition, be very little
waste.

That is, the Atom Economy (Percentage) will be high

(just below 100).

In an ideal world, all industrial chemical processes should

have an atom economy of 100% since this would mean
there would be no waste (unwanted material).

In practice, much unwanted material that used to be

dumped/buried/burned is now used.

For example, the waste slag from a Blast Furnace is

nowadays turned into insulation blocks for new homes.

Atom Economy = Mass of useful product x100

Total mass of reactants used

22
 Calculating Atom Economy

Most chemical reactions produce useful products and waste

products. Atom economy allows us to calculate the percentage
of reactants that are converted into useful products.

Example 1:
What is the atom economy for making hydrogen by reacting
coal with steam?

C(s) + 2H2O(g) CO2(g) + 2H2(g)

Step 1: Work out the Mr and Ar values for the reactants and
the useful products.

C(s) + 2H2O(g) CO2(g) + 2H2(g)

Mr / A r 2(2+16) 2x2
12 36 4

Step 2: Work out the percentage of useful product using the

following equation:

Atom Economy = Mass of useful product x100

Total mass of reactants used

= 4 x 100 = 8.3%
36 + 12

So this reaction is not very economical and probably would not

be used to make hydrogen industrially.

23
Example 2:

Lithium hydroxide will react with nitric acid to produce lithium nitrate
plus water. Suppose that we are trying to make lithium nitrate, and that
the water we also make is the waste material. Firstly we write an
equation
LiOH + HNO3 LiNO3 + H 2O

Then we write the Mr (Relative Formula Masses) underneath

LiOH + HNO3 LiNO3 + H 2O
24 63 69 18

Atom economy = (69/87) x 100 = 79.3%

(If you are wondering where 87 comes from, its 24 + 63)

Calculate the atom economy percentage for the Blast Furnace reaction.
The desired product is iron and the waste product is carbon dioxide

Fe2O3 + 3CO 2Fe + 3CO 2

24
Calculate the atom economy percentage for the Haber Process. The
desired product is ammonia (NH3).

N2 + 3H2 2NH3

Calculate the atom economy percentage for the Oswald Process (the
desired product is nitric acid).

NH3 + 2O2 HNO3 + H 2O

25
Try this typical GCSE question

26
 Comparing the Atom Economy for 2
methods of Titanium (Ti) extraction

Titanium is a very useful metal.

It is light (low density), strong, hard and resists
corrosion.

For these reasons it has many uses including in the

aerospace industry & for artificial hip joints.

Although there is plenty of titanium in the Earths crust it is

an expensive metal due to extraction costs and the low atom
economy.

There are 2 methods for extracting Titanium the traditional

method and the modern electrolytic method.

Method 1 The Traditional Method

The following reaction is used:

TiO2 + 2Cl2 + C + 4Na CO2 + Ti + 4NaCl

Calculate the atom economy for this reaction:

(The desired product is Ti (CO2 & NaCl are waste products)

TiO2 + 2Cl2 + C + 4Na CO2 + Ti + 4NaCl

27
 Do you agree that this is rather wasteful?
Your answer should have been 14.7%.
This means that 100 14.7 = 85.3% is potentially waste
material (or, at least, not very useful).

Method 2 The Modern Electrolytic Method

More recently a better process has been developed using

direct electrolysis.
This will hopefully enable titanium to be produced at half
its current price, or even less.
You do not need to know details of the process, but it can
be summarised as follows:

TiO2 Ti + O2

Notice that the only by-product is oxygen, which is, of

course, very useful.
Can YOU now work out the atom economy percentage for
this process?
It ought to be much more efficient than 14.7%.

TiO2 Ti + O2

28
Relevant Internet and School Network Links

In school, try these web links and click on the white arrow in the green
square to view:

http://www.yenka.com/freecontent/item.action?quick=13i#
http://www.yenka.com/freecontent/item.action?quick=13j#
http://www.yenka.com/freecontent/item.action?quick=u0

School network Links:

SUBJECTS > SCIENCE > CHEMISTRY > ABSORB CHEMISTRY FOR

GCSE > INTRODUCING MOLES
SUBJECTS > SCIENCE > CHEMISTRY > ABSORB CHEMISTRY FOR
GCSE > MOLES IN CHEMICAL EQUATIONS
SUBJECTS > SCIENCE > FOOTPRINTS > MATERIALS & THEIR
PROPERTIES > ELEMENTS, COMPOUNDS & MIXTURES
SUBJECTS > SCIENCE > CHEMISTRY > ABSORB CHEMISTRY FOR
GCSE > EXTRACTION OF TITANIUM
SUBJECTS > SCIENCE > CHEMISTRY > ABSORB CHEMISTRY FOR
GCSE > MOLES & CHEMICAL FORMULAE

Useful websites:

http://web.visionlearning.com/MW_calculator.shtml
http://www.tufts.edu/as/wright_center/fellows/george/georgepage3.ht
m

Please note some of these websites include extension materials and

useful concepts (such as the mole) which can be extremely useful but
you do not necessarily need to know for your exam!

29