Scribd
Upload
187 views

3.5 Wiring Schematic: Basic Operating Principles Design Guide

The document provides a wiring schematic for a 3-phase power input driving a motor with a switch mode power supply and optional brake resistor. Digital and analog inputs and outputs are shown connected along with relay and RS-485 interface terminals. Safety instructions are provided for an optional safe torque off terminal.

Uploaded by

01666754614
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
187 views

3.5 Wiring Schematic: Basic Operating Principles Design Guide

The document provides a wiring schematic for a 3-phase power input driving a motor with a switch mode power supply and optional brake resistor. Digital and analog inputs and outputs are shown connected along with relay and RS-485 interface terminals. Safety instructions are provided for an optional safe torque off terminal.

Uploaded by

01666754614
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Basic Operating Principles Design Guide

3.5 Wiring Schematic

130BD599.10
3-phase
power
91 (L1)
92 (L2)
93 (L3)
(U) 96
(V) 97
(W) 98
3 3
input
95 PE (PE) 99
Motor

88 (-) Switch Mode


DC bus
Power Supply
89 (+)
10 V DC 24 V DC (R+) 82 Brake
15 mA 130/200 mA resistor
50 (+10 V OUT) + - + -
+10 V DC (R-) 81
S201
0/-10 V DC-
53 (A IN)
1 2

ON

+10 V DC relay1
ON=0/4-20 mA
0/4-20 mA S202 03
OFF=0/-10 V DC -
1 2

0/-10 V DC - +10 V DC
ON

54 (A IN) 240 V AC, 2 A


+10 V DC 02
0/4-20 mA
55 (COM A IN) 01
* relay2
12 (+24 V OUT) 06
240 V AC, 2 A
13 (+24 V OUT) P 5-00 05
400 V AC, 2 A
24 V (NPN)
18 (D IN) 04
0 V (PNP)
24 V (NPN)
19 (D IN) 0 V (PNP) (COM A OUT) 39 Analog Output
0/4-20 mA
(A OUT) 42
20 (COM D IN)
24 V (NPN)
27 (D IN/OUT) 0 V (PNP) S801
24 V ON=Terminated
1 2

ON

OFF=Open

0V 5V
* 24 V (NPN)
29 (D IN/OUT) 0 V (PNP)
24 V
S801 0V
0V
RS-485 RS-485
(N RS-485) 69
24 V (NPN) Interface
32 (D IN) 0 V (PNP) (P RS-485) 68
24 V (NPN) **
33 (D IN) 0 V (PNP) (COM RS-485) 61
: Chassis

* : Ground
37 (D IN)

Figure 3.2 Basic Wiring Schematic

A=Analog, D=Digital
*Terminal 37 (optional) is used for Safe Torque Off. For Safe Torque Off installation instructions, refer to the Safe Torque Off
Instruction Manual for Danfoss VLT Adjustable Frequency Drives. Terminal 37 is not included in FC 301 (except enclosure type
A1). Relay 2 and terminal 29 have no function in FC 301.
**Do not connect cable shield.

MG33BF22 Rev. 2014-04-04 All rights reserved. 17

You might also like