Field Service Ver. 1.0 Jun. 2008 5. Firmware upgrade 5. Firmware upgrade 5.1 Preparations for firmware rewriting 5.14 Items required 5 8 § * Drive which enables writing/reading of compact flash + Compact flash (service tool) 5.1.2 Writing data to compact flash 1. Prepare firmware data. 2, Format the compact flash on the PC. NOTE + Use the FAT file format for formatting the compact flash. The machine does not recognize any compact flash that has been formatted in FAT32 or other format. 3. Copy the firmware data to the compact flash. NOTE + When copying the data to the compact flash, directly copy the files contained in the folder, instead of copying the folder. Copy only the data to be rewritten. Note that no display is given on the control panel if wrong firmware is copied. * Be sure to take note of the checksum value of the firmware data. 5.1.3 Checking version * Before rewriting firmware, check the current ROM version. See P.143 31bizhub €200 5. Firmware upgrade Field Service Ver. 1.0 Jun. 2008 5.2 Firmware rewriting procedures NOTE + NEVER remove or insert the compact flash card with the machine power turned ON. + Confirm the current version before upgrading the firmware. + Before upgrading the firmware, confirm that no jobs remain within the machine. 5.2.1 Controller 1. Turn OFF the main power switch. 2, Remove the cover [1] from the com- pact flash insertion slot. 3. Insert the compact flash [1], to which the controller files to be rewritten are copied, into the slot. NOTE + Do not copy engine, job separator, and other firmware to the compact flash. anaFF2cs2604 4, Turn ON the main power switch and the sub power switch. 5. The Flash ROM Setup screen is displayed on the control panel display, and upgrading starts. 6. When “FINISH" is displayed at the bottom of the control panel, upgrading of the firm- ware is completed. Turn OFF the main power switch. NOTE + NEVER turn OFF the main power switch until “FINISH” appears. 32Field Service Ver. 1.0 Jun. 2008 5. Firmware upgrade 7. Remove the compact flash card [1] from the slot. ee ORFF 2052608 8. Reinstall the cover of the slot. 9. Turn ON the main power switch and the sub power switch, 10. Select [Admin.] > [Firmware Version). 11. Check that the firmware version has been updated. 5.2.2 Engineljob separator NOTE + Make sure that the controller firmware is not copied to the compact flash. + To rewrite both the engine and job separator firmware at the same time, copy both types of firmware to the compact flash. to the compact flash, no display is given on the control 1. 2, Remove the cover [1] from the com- pact flash insertion slot. 0zFF2cs2508 8 3bizhub €200 5. Firmware upgrade Field Service Ver. 1.0 Jun. 2008 nm -AR2FF2CS2604 3. Insert the compact flash [1], to which the engine and job separator firm- ware data is copied, into the slot. s Turn ON the main power switch and the 5. Call the service mode to the screen. See P.146 sub power switch, ORFF 2652708 6. Touch [Download Firmware]. AOQFFRESCEOA 7. Select [Engine] and touch [OK]. NOTE + Touch [Job Sep.] also if the job sep- arator firmware data is also to be rewritten.ield Service Ver. 1.0 Jun. 2008 AOAFFDES2004 Do you want to download? AnzFFZESGO08 ARFFRESCIOA 5. Firmware upgrade 8. Check the message, then select (Yes). 9, The screen on the left will appear as soon as downloading starts. NOTE * While this screen is being dis- played, which indicates that the firmware is being rewritten, never turn OFF the main power switch or sub power switch, unplug the power cord, open the cover, or oth- erwise perform action to hamper the rewriting procedure. 10. The screen on the left appears when the rewriting sequence is completed. 11. Check the checksum value recorded against that shown on the screen and make sure that there is a match between the two values. 12. Turn OFF the main power switch. 35 5bizhub C200 5. Firmware upgrade Field Service Ver. 1.0 Jun. 2008 13. Remove the compact flash card [1] from the slot. n ADRFFACS2608 14. Reinstall the cover of the slot. 15. Turn ON the main power switch. 16. Select [Admin.] -> [Firmware Version} 17. Check that the firmware version has been updated. 36