Scribd
Upload
431 views2 pages

MOSFET Worksheet R2 PDF

This document provides a worksheet to help determine if a MOSFET can be used in a circuit. It outlines 4 key steps: 1) identifying the pinout of the MOSFET, 2) checking the threshold voltage and maximum voltages, 3) determining the drain-source resistance, and 4) calculating the maximum power of the MOSFET based on its thermal resistance and maximum junction temperature. Following these steps with the datasheet ensures the MOSFET meets the voltage and power requirements for the intended application.

Uploaded by

vladan.izbm
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
431 views2 pages

MOSFET Worksheet R2 PDF

This document provides a worksheet to help determine if a MOSFET can be used in a circuit. It outlines 4 key steps: 1) identifying the pinout of the MOSFET, 2) checking the threshold voltage and maximum voltages, 3) determining the drain-source resistance, and 4) calculating the maximum power of the MOSFET based on its thermal resistance and maximum junction temperature. Following these steps with the datasheet ensures the MOSFET meets the voltage and power requirements for the intended application.

Uploaded by

vladan.izbm
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

MOSFET Worksheet

MOSFETs are a great transistor to use in most circuits. They can be a little bit complicated to
design in. Use this worksheet to find the critical information in the datasheet and to help
determine if it can be used in your circuit.

Step 1: Pin-Out
Function Pin Number

Gate

Drain

Source

Tab
(Which pin)

The tab of the transistor is connected to one of the pins, make sure you note that. Also, verify
the orientation of this picture is the same as your datasheet.

Step 2: Threshold Voltage (VGS or VTH) and Max VDS


Function Value Comment

The voltage range necessary to


VGS
turn on the MOSFET

Voltage of the I/O pin used (VGS


VCC
must be less)

The maximum operational voltage


VDS
for the load side

Voltage of whatever you are trying


VLOAD
to control (VDS must be more).

VCC is whatever voltage your circuit I/O runs at, which is probably 3.3V or 5.0V. Make sure this
number is bigger than the minimum threshold voltage VGS.

If youre using a battery or external supply for the load, make sure VDS is bigger than that power
source.

R2 - 09-July-2016 addohms.com/mosfet-guide Pg 1 of 2
Step 3: Drain to Source Resistance (RDS-On)
Function Value Comment

Max RDS Rated limit of RDS. (Will vary with VGS.)

Actual
Expected resistance at your VGS
RDS

Look for the RDS. Keep in mind that RDS will vary with VGS. So the limit (or Max) stated in the
description of the MOSFET, may not apply to your circuit.

Once you know the on-resistance, you can use your loads current to calculate how many watts
the MOSFET will dissipate.

Step 4: Calculate Max MOSFET Power


Function Value Comment

Max
Should be in the range of 125C to 175C.
Junction
If not stated clearly, use 150C.
Temp
Thermal Resistance: Junction-to-Ambient
RJA
Units should be C/W
Sometimes the Maximum Junction Temperature isnt clearly stated. If that is the case, just
assume 150C for TJMax.

TAmbient is the air temperature. Room temperature is usually around 25C.

Make sure that number calculated in Step 3 is less than Step 4. If Step 3 is bigger, you need a
heatsink.

R2 - 09-July-2016 addohms.com/mosfet-guide Pg 2 of 2

You might also like