Scribd
Upload
76 views

Section Analysis

This document analyzes the properties and performance of a cold-formed light gage steel section. It provides key metrics like material yield strength, section properties including area, moments of inertia, and section modulus. Bending capacities are calculated and checked against design limits to ensure the section is safe against yielding under the applied loads.

Uploaded by

Rachelle Quilala
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
76 views

Section Analysis

This document analyzes the properties and performance of a cold-formed light gage steel section. It provides key metrics like material yield strength, section properties including area, moments of inertia, and section modulus. Bending capacities are calculated and checked against design limits to ensure the section is safe against yielding under the applied loads.

Uploaded by

Rachelle Quilala
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
You are on page 1/ 2

ANALYSIS OF COLD-FORMED LIGHT GAGE SECTIONS (LC) LC 150 X 50 X 18 X 3.

0MM

SECTION PROPERTIES :

Fy = 248.00 MPa 47.00


E = 200,000.00 MPa
4 2 1
5
rx = 56.80 mm 4 2 5
16.50
Sx = 33,700.00 mm^3 3 3
Zx = 40,486.96 mm^3
Ix = 2,525,000.00 mm^4 73.5 1
ry = 17.60 mm 57.00
Sy = 6,900.00 mm^3 ho = 147
Zy = 12,161.12 mm^3 1
Iy = 243,000.00 mm^4
J = mm^4
Cw = mm^6 57.00
A = 783.00 mm^2 73.5 1
H = 150.00 mm
B = 50.00 mm 3 4
4 16.50
C = 18.00 mm 2 5
5 3 2 6
t = 3.00 mm
xc = 14.70 mm
13.20 33.80
Lb = 2,000.00 mm

rave. = 7.5730 mm Zx Area, mm^2 i, mm Area*, mm^3 A&B, mm


P = 261.00 mm 1 197.78 32.96 6,519.55
A = 783.00 mm^2 2 95.56 73.50 7,023.81
3 26.78 61.46 1,646.05
4, 5 71.37 70.81 5,054.07
391.50 ### 51.71

Zy1 Area, mm^2 iL, mm Area*, mm^3 L, mm


1 395.56 13.20 5,221.42
2, 3 33.76 2.81 94.99
4, 5 71.37 10.51 750.22
500.70 6,066.63 12.12

Zy2 Area, mm^2 iR, mm Area*, mm^3 R, mm


1, 2 157.36 13.11 2,063.57
3, 4 53.56 33.80 1,810.40
5, 6 71.37 31.11 2,220.52
282.30 6,094.49 21.59

ULTIMATE BENDING MOMENTS :

MNu = 3,000,000.00 N-mm = 3.000 kN-m


MTu = 60,000.00 N-mm = 0.060 kN-m

CHECK FOR YIELDING (LRFD)

506.2-1 _=_=_ _= 10,040,766.25 N-mm = 10.041 kN-m Mnx

506.6-1 _=_=_ _1.6_ _


_ 3,015,956.85 N-mm
_=
1.6_ _= 2,737,920.00 N-mm
Use _= 2,737,920.00 N-mm = 2.738 kN-m Mny

_/(_ )+_/( _ 2)1.00


To be safe, where = 0.90
(Tangential load does not pass through shear center)
_/(_ )+_/( _ 2)=
0.380679 Section is SAFE against yielding.

CHECK FOR DEFLECTION

You might also like